Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Particle size distribution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Highly Durable and Active Pt/Sb-Doped SnO 2 Oxygen Reduction Reaction Electrocatalysts Produced by Atomic Layer Deposition

Platinum supported on mixed-metal oxides (MMOs) are a class of active and durable cathode catalysts for proton exchange membrane fuel cell (PEMFC) due to a combination of the high oxidative stability of the supports and strong-metal-support interactions (SMSI) that enable them to exceed the activity of Pt/C. Herein, we solve a significant remaining challenge with Pt/MMO systems, namely the relatively low surface area and porosity. This is achieved by dispersing nearly-uniform Pt clusters using atomic layer deposition (ALD) on highly conductive (6.2 S/cm) and stable antimony doped tin dioxide (ATO) support. ALD-Pt/ATO exhibited significantly higher electrochemically active surface area (ECSA) (74 m 2 /g) and oxygen reduction reaction (ORR) catalytic activity (102 mA/mg Pt at 0.9 V vs. RHE) compared to Pt/ATO synthesized using ethylene glycol (ECSA=31 m 2 /g Pt , mass activity=52 mA/mg Pt at 0.9 V vs. RHE) and formic acid reduction methods (ECSA=28 m 2 /g Pt , mass activity=46 mA/mg Pt at 0.9 V vs. RHE). Further characterization showed that wet chemical methods resulted in poorer Pt particle dispersion, poor control over Pt particle size distribution and chemical degradation of the support (during Pt deposition). Given the near-ideal Pt particle size distribution of the ALD-Pt/ATO, particle size growth and loss of ECSA was found to be minimal over the course of rigorous potential cycling. Thus, after 10,000 potential cycles between 1V and 1.5V vs. RHE, ALD-Pt/ATO and other Pt/ATOs were found to retain 100% of their initial ECSA compared to 57.6% retention for Pt/C. Upon testing in a H 2 /air PEMFC, following 1,000 potential cycles, the change in ALD-Pt/ATO performance was negligible while Pt/C exhibited a 68.2% loss of initial peak power density. Thus, ALD-Pt/ATO is an active and highly durable ORR electrocatalyst in PEMFCs under start-up-shut down conditions.

25 ENERGY STORAGE↗
DOE OSTI2022

mergedsmpsaps

Merged aerosol particle size distributions for the Aerodynamic Particle Sizer (APS) and Scanning Mobility Particle Sizer (SMPS) instruments

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Evaluation of methods for characterizing the fine particulate matter emissions from aircraft and other diffusion flame combustion aerosol sources

The U. S. Environmental Protection Agency in collaboration with the U. S. Air Force Arnold Engineering Development Complex conducted the VAriable Response In Aircraft nvPM Testing (VARIAnT) 3 and 4 test campaigns to compare nvPM emissions measurements from a variety of diffusion flame combustion aerosol sources (DFCASs), including a Cummins diesel engine, a diesel powered generator, two gas turbine start carts, a J85-GE-5 turbojet engine burning multiple fuels, and a Mini-CAST soot generator. The VARIAnT research program has conducted four test campaigns to date with the VARIAnT 3 and 4 test campaigns focusing on BC mass instrument performance, use of gas turbine engine sources for BC mass instrument calibration, and the characterization of the aerosols produced from the combustion sources. Results from both campaigns revealed agreement of about 20% between the AVL Micro-Soot Sensor, the Cavity Attenuated Phase Shift (CAPS PMSSA) monitor and the thermal-optical reference method for elemental carbon (EC), independent of the calibration source used. For the Artium LII-300, the measured mass concentrations in VARIAnT3 fall within 18% and in VARIAnT4 fall within 32% of the reference EC mass concentration when calibrated on a combustor rig in VARIAnT3 and on a LGT-60 start cart in VARIAnT4, respectively. It was also found that the three mass instrument types (MSS, CAPS PMSSA, and LII-300) can exhibit different BC to reference EC ratios depending on the emission source that appear to correlate to particle geometric mean mobility diameter, morphology, or some other parameter associated with particle geometric mean diameter (GMD) with the LII-300 showing a slightly stronger apparent trend with GMD. Systematic differences in LII-300 measured mass concentrations have been reduced by calibrating with a turbine combustion source (combustor or turbine engine). With respect to the particle size measurements made, the sizing instruments (TSI SMPS, TSI EEPS, and Cambustion DMS 500) were found to be in general agreement in terms of size distributions and concentrations with some exceptions. Teflon filter measurements of the total aerosol mass produced by the various DFCASs differed from the reference EC, BC, and integrated particle sized distribution measured aerosol masses. The Teflon filter measured mass was 30 to 40% greater than the reference EC and 50 to 60% greater than the BC mass for the J85 in both test campaigns. The measurements of particle size distributions and single particle analysis by miniSPLAT indicated the presence of large particles (>100 nm) having more compact morphologies, higher effective density, and a composition dominated by OC and ash. This increased large particle fraction is also associated with higher values of single scattering albedo measured by the CAPS PMSSA instrument and higher OC/EC measurements. These measurements indicate gas turbine engine emissions can be a more heterogeneous mix of particle types beyond the original E31 assumption that it is mainly composed of black carbon.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2024

Microtomographic Measurements of Total Air‐Water Interfacial Areas for Soils

Abstract Synchrotron X‐ray microtomography (XMT) was used to measure total air‐water interfacial areas (A aw ) as a function of water saturation (S w ) for several soils that comprise a range of physical and geochemical properties. Measurements were also conducted for glass beads and quartz sands for comparison. Apparent near‐linearA aw ‐S w relationships are observed for the three sands and the three sandy soils. In contrast, the measured interfacial areas for two soils that contain greater proportions of silt and clay are strongly nonlinear functions of water saturation. The greater degree of nonlinearity observed for these two soils is due to their much greater particle‐size distributions (i.e., uniformity coefficients) and their concomitant greater range in pore sizes. Interfacial areas determined with the thermodynamic method were used to benchmark the XMT measurements. XMT‐measured interfacial areas compare well to the thermodynamic‐determined values for the sands and sandy soils. In contrast, the XMT‐measured interfacial areas for the two soils with larger particle‐size distributions are not fully congruent with the thermodynamic‐determined values. Both of these soils have large fractions of pore space comprising nominal pore diameters smaller than the resolution of the XMT imaging. These results suggest that air‐water interfacial area may not always be fully characterized by standard XMT for soils with large particle‐size distributions.

Environmental Sciences & Ecology↗
DOE OSTI2021

238 PuO 2 In Vitro Lung Dissolution Rate and Particle Size Determination for Material Involved in the June 8, 2020 Incident at the Los Alamos National Laboratory PF-4 Facility

As part of the LANL response to the June 8, 2020 238 PuO 2 inhalation exposure incident in PF-4, the Nuclear and Radiochemistry Group (C-NR) was asked to assist in determining the lung dissolution rate and particle size distribution of the airborne material. These material characteristics, along with urine and fecal bioassay data, are used by the Radiation Protection Services (RP-SVS) internal dosimetrists to refine dose estimates for exposed workers. Similar to previous studies, an in vitro lung dissolution rate study was performed to assess how fast 238 Pu is cleared from the lungs. Given that PuO 2 is a relatively insoluble material, it dissolves very slowly and requires in vitro studies of 100 or more days to estimate dissolution rates. This report details the results of a 100 day in vitro dissolution rate study and the particle size characteristics of 238 PuO 2 collected on an air filters during the incident. Results show that the 238 PuO 2 involved in this incident has behavior comparable to PuO 2 from previous in vitro studies, with approximately 1% of material dissolving quickly, and 99% of the material dissolving very slowly, with a half-time of approximately 120 years. This is somewhat slower than what was determined in a previous study of LANL 238 PuO 2 , which had an experimental dissolution half-time of 3 years, but significantly faster than 3000 years measured for 239 PuO 2 . Particle size distribution measurements indicate that particle sizes range from 0.10 µm – 6 µm, with most < 2 µm, which is reasonable based on our understanding of the process history of the 238 PuO 2 . Particle size, specific surface area, calcining temperature, specific activity, and age all are known factors that can impact the dissolution rate of refractory materials, however, there are too few studies to quantify the exact influence of these parameters on a measured dissolution rate. The results of this study add to that knowledge base, and provide new insights into the dissolution rates for this LANL process-specific 238 PuO 2 material.

63 RADIATION, THERMAL, AND OTHER ENVIRON. POLLUTAN↗
DOE OSTI2024

3002 Humidified Tandem Differential Mobility Analyzer (HTDMA) Instrument Handbook

The Brechtel Manufacturing Inc. (BMI) Humidified Tandem Differential Mobility Analyzer (HT-DMA Model 3002) (Brechtel and Kreidenweis 2000a,b, Henning et al. 2005, Xerxes et al. 2014) measures how aerosol particles of different initial dry sizes grow or shrink when exposed to changing relative humidity (RH) conditions. It uses two different mobility analyzers (DMA) and a humidification system to make the measurements. One DMA selects a narrow size range of dry aerosol particles, which are exposed to varying RH conditions in the humidification system. The second (humidified) DMA scans the particle size distribution output from the humidification system. Scanning a wide range of particle sizes enables the second DMA to measure changes in size or growth factor (growth factor = humidified size/dry size), due to water uptake by the particles. A Condensation Particle Counter (CPC) downstream of the second DMA counts particles as a function of selected size in order to obtain the number size distribution of particles exposed to different RH conditions.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Characterization of Surrogate Molten Salt Reactor Aerosol Streams

Measuring the aerosol evolution from MSRs is important for monitoring the off-gas system of the reactor and is particularly important for detecting off-normal conditions. In a molten salt reactor (MSR) accident scenario, an aerosol release would be a major factor in the source term. This aerosol stream would likely be generated from a breach in the cover gas system, which causes particles produced from fission itself to escape, or from a salt spill that produces aerosols through splashing and secondary reactions. The particle size of the produced aerosols is anticipated to vary greatly and range from 0.01 to 10 µm. The transport of these aerosols would be dependent on the particle size. A better understanding of aerosol generation, size, and monitoring methods are needed to inform estimation and mitigation of potential aerosolized source terms from MSRs. While salt spill experiments are being performed at Argonne National Laboratory, the development of aerosol characterization and monitoring methods are being developed at Oak Ridge National Laboratory. To generate prototypic aerosols for use in testing monitoring instruments and mitigation methods, a surrogate aerosol stream was produced with a Collison nebulizer, and the particle size distributions were measured with a cascade impactor. The results demonstrated that by changing the nebulizer pressure, the aerosol particle size distribution can be adjusted to best match the region of interest for experiments with higher pressures, driving the particle size down. However, nearly all aerosols formed exceeded 1 µm in diameter, providing a lower bound for the surrogate aerosol stream. In addition to verifying the applicability of this surrogate aerosol stream, this work has shown that a laser induced breakdown spectroscopy monitoring system that is under development is resilient to changes in particle sizes, increasing its robustness for off-gas monitoring.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2020

Analysis of hematite attrition in a grid jet apparatus

Particulate attrition is of interest for novel carbon-capture processes such as chemical looping combustion because the makeup cost of oxygen carrier is a significant portion of operating cost. As such, models to study and predict attrition of various oxygen carriers in fluidized bed systems are being developed. One of the regions of concern in fluidized bed systems is the high-velocity jet region near gas distributors in a fluid bed. This work studies the attrition of hematite particles using a modified ASTM apparatus to measure the particle size distribution throughout the experiment. Bed weight and gas velocity were varied. Hematite particles above the corresponding threshold value had a severe variation of particle size distributions which decreased with time. Weight fractions of the sieves over time were fit to a linear, time-variant population balance model to offer insight into particle attrition. The first-order rate constant was modified as a decaying exponential.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Composite binder, processing, and particle size effects on mechanical properties of non-hazardous high explosive surrogates

Plastic-bonded explosives (PBX) are polymer matrix composites that are highly loaded with micron-scale explosive crystals. The thermal and mechanical properties of these materials must be well-understood so that appropriate engineering models can be developed, but testing such properties under many scenarios can be hazardous and expensive. A non-hazardous PBX surrogate (“mock”) may be used in place of a PBX in many experiments if the thermomechanical properties are well-matched. Our previous research has shown that 5-iodo-2'-deoxyuridine (IDOX) is a promising crystalline filler material for the explosive cyclotetramethylene-tetranitramine (HMX). In this study, we investigate how the binder composition, variations in the IDOX particle size distribution, and pressing temperature affect the compressive strength and elastic modulus. We observe that while the binder system used in the composite dominates the mechanical response, the particle size distribution and pressing conditions do have a measurable effect on the material compliance and strength.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗
DOE OSTI2025

Let’s Stick Together: Interplay of Moisture, Particle Size, and Anatomical Fraction in the Flowability of Corn Stover Crumbles

Handling of agricultural waste biomass feedstocks (such as corn stover) is a persistent challenge in the production of biofuels and chemicals at integrated biorefineries. Inconsistent flowability and high feedstock variability creates equipment downtime and processing challenges. This work investigates the influence of anatomical fractionation and moisture content on the bulk solids handling behavior of corn stover crumbles. A combination of rotational shear testing, tribological measurements, and surface and sorption characterization techniques (inverse gas chromatography (IGC), dynamic vapor sorption (DVS), and electron microscopy) were used to evaluate the contributions of particle composition, size, and surface properties to flow behavior. Shear and frictional testing revealed that moisture content has the greatest effect on flowability, significantly increasing unconfined yield strength (ƒ c ) and reducing the flow function coefficient (F F C), regardless of anatomical fraction. While differences in surface energy were observed between fractions, particularly in polar contributions (γ AB ), these did not correspond to meaningful differences in flow behavior. Coarser 6 mm particles exhibited poorer flow performance than 4 mm crumbles, likely due to broader particle size distributions and increased particle interlocking. Taken together, these results suggest that anatomical fractionation provides minimal benefit from a bulk handling perspective. Moisture content and particle size heterogeneity dominate handling behavior, reinforcing the utility of unfractionated corn stover in processing environments. These insights can inform the design of more efficient and reliable feedstock processing systems for agricultural biomass in integrated biorefineries.

09 BIOMASS FUELS↗
DOE OSTI2024

A remote sensing algorithm for vertically resolved cloud condensation nuclei number concentrations from airborne and spaceborne lidar observations

Cloud condensation nuclei (CCN) are mediators of aerosol–cloud interactions (ACIs), contributing to the largest uncertainties in the understandings of global climate change. We present a novel remote-sensing-based algorithm that quantifies the vertically resolved CCN number concentrations (N CCN ) using aerosol optical properties measured by a multiwavelength lidar. The algorithm considers five distinct aerosol subtypes with bimodal size distributions. The inversion used the lookup tables developed in this study, based on the observations from the Aerosol Robotic Network, to efficiently retrieve optimal particle size distributions from lidar measurements. The method derives dry aerosol optical properties by implementing hygroscopic enhancement factors in lidar measurements. The retrieved optically equivalent particle size distributions and aerosol-type-dependent particle composition are utilized to calculate critical diameters using κ-Köhler theory and N CCN at six supersaturations ranging from 0.07 % to 1.0 %. Sensitivity analyses indicate that uncertainties in extinction coefficients and relative humidity greatly influence the retrieval error in N CCN . The potential of this algorithm is further evaluated by retrieving N CCN using airborne lidar from the NASA ObseRvations of Aerosols above CLouds and their intEractionS (ORACLES) campaign and is validated against simultaneous measurements from the CCN counter. The independent validation with robust correlation demonstrates promising results. Furthermore, the N CCN has been retrieved for the first time using a proposed algorithm from spaceborne lidar – Cloud-Aerosol Lidar with Orthogonal Polarization (CALIOP) – measurements. The application of this new capability demonstrates the potential for constructing a 3D CCN climatology at a global scale, which helps to better quantify ACI effects and thus reduce the uncertainty in aerosol climate forcing.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

The influence of cooling rate on condensation of iron, aluminum, and uranium oxide nanoparticles

Fundamental observations of particle size distributions are needed to develop models that predict the fate and transport of radioactive materials in the atmosphere following a nuclear incident. The extent of material transport is influenced by the time scales of particle formation processes (e.g., condensation, coagulation). In this study, we investigated the influence of cooling time scales on size distributions of uranium, aluminum, and iron oxide particles that are synthesized separately under identical run conditions inside the controlled environment of an argon plasma flow reactor. Two distinct temperature distributions are imposed along the flow reactor by varying the argon flow rate downstream of the plasma torch. The vaporized reactants of uranium, aluminum, and iron are cooled from about 5000K to 1000K before they are collected on silicon wafers for ex situ scanning electron microscope analysis. The microscope images show that the sizes of the largest aluminum and iron oxide particles heavily depend on the cooling time scales, whereas significant size variation with cooling rate is not observed for uranium oxide particles. In addition, the size distribution of aluminum oxide particles exhibits the broadest range among all three metal oxides studied. We performed simulations of particle size distributions using a kinetic model that couples gas phase oxidation chemistry with particle formation processes, including nucleation, condensation, and coagulation. The model results demonstrate the strong sensitivity of particle size distribution to different cooling histories (i.e., temperature vs residence time) along the flow reactor. In conclusion, the kinetic model also helps identify directions for future research to improve the predictions.

36 MATERIALS SCIENCE↗
DOE OSTI2025

ED-cPSD: Fast Phase-Size Distribution via Sequential Erosion-Dilation

The Erosion-Dilation continuous Phase-Size Distribution, ED-cPSD, is an application for calculating continuous pore and particle-size distribution from digital reconstructions and/or image-based structural data. It is based on the erosion-dilation continuous phase-size distribution method. A continuous size distribution is a measure of the probability density of finding a particle or pore of a certain size. These distributions are of interest in any field of study involving porous media, including but not limited to electrochemistry, petroleum engineering, geology, and food science. The algorithm behind the software provides a computationally efficient way to calculate phase-size distributions for large domains. For a 3D battery electrode reconstruction with 1.3 x 10 8 voxels, the particle size distribution is derived in under 2 min on a desktop, while also retaining flexibility and computational efficiency for HPC-scale multi-threading. The software can handle structures with over 10 9 voxels. The algorithm is roughly 280 times faster than a previous version on the same task.

Characterization↗
DOE OSTI2023

Understanding Biases in Sample Preparation Techniques for Coupled Scanning Electron Microscopy and MAMA PuO 2 Morphological Analysis

In this project, the scanning electron microscopy (SEM) sampling method used during the statistical design study (SDS) was investigated to determine if any sampling biases were present in the analyzed data. Using standard particle size distribution powders from the National Institute of Standards and Technology (NIST 1984 standard reference material) with the origin wet dispersion method, it was determined that a bias to smaller particles was present. This was supported by theoretical calculations using Stokes’ law to determine the settling rate of spherical particles of roughly the same size and mass as those found in the SDS. Based on the theoretical calculations, it was determined that the settling rate for each of the 76 powder sets in the SDS could be unique based on specific particle shape and mass distributions, making a universal correction factor/formula not applicable. Therefore, priority shifted to developing an improved wet dispersion method that significantly reduced the particle settling rate for all particle size and shapes. This was achieved by replacing the original solvent (isopropyl alcohol) with a heavy liquid (lithium heteropolytungstates), which dramatically slowed the settling rate and allowed for the capture of a suitable homogeneous aliquot. SEM imaging and Morphological Analysis for Material Attribution (MAMA) software analysis were conducted on the NIST standard, and the SEM/MAMA data were compared to data captured by a dynamic image analysis particle size analyzer. The resulting data confirmed that the new wet dispersion method does indeed deliver an improved representative aliquot to the SEM stub. For instance, in the NIST certificate, the average particle size is ~17.1 µm ± 2.2 µm with a normal distribution. The initial wet dispersion method resulted in a drastically reduced average particle size of 6.1 µm in addition to a non-representative heavy bi-modal distribution whereas the improved LST wet dispersion method resulting in an average particle size that was much closer to the NIST certificate (12.7 µm) with a similar normal distribution. Although the improved method was still short of the NIST certificate average, atomic force microscopy analysis determined that the resulting ~20-25% reduction in size was due to particles sinking into the carbon sticky tape used for SEM imaging. It is believed that that this bias can be calibrated in a much more predicable manner than the original settling rate bias. In addition, the matching normal distribution curves between the NIST certificate and the heavy liquid method indicate a much-improved representative aliquot has been sampled and imaged. A surrogate CeO 2 powder was used to reflect PuO 2 more accurately and to aid in implementing radiological controls and shielding. The resulting data sets from the SEM/MAMA method and the particle size analyzer give almost identical average particle sizes and particle distribution statistics. Future work will re-analyze several select runs from the SDS to determine if morphological signatures can be found with the improved sampling method.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Bimodal particle distributions with increased thermal conductivity for solid particles as heat transfer media and storage materials

Solid particles are being considered in several high temperature thermal energy storage systems and as heat transfer media in a variety of advanced power generation systems, particularly in concentrated solar power plants. The downside of such an approach is the low overall heat transfer coefficients caused by the inherently low thermal conductivity values of the low-cost solid media when coupled to heat exchanger for the power cycle working fluid. Choosing the right particle size distribution, emittance, and material of the solid media can all make a substantial difference in packed bed thermal conductivity. Current research though exclusively focuses on continuous unimodal distributions of particles. Here, in this work, we propose the use of a binary particle system with a bimodal size distribution to significantly increase packed bed thermal conductivity by reducing packed bed porosity. This is the first study related to ceramic solid particle heat transfer that has considered the thermal conductivity of non-unimodal size distributions at room and elevated temperatures. The following study found that for the binary particle system using Carbo particles CP 16/30 – CP 70/140 where the large particle volume fraction was 50% there was an 17–47% increase in packed bed thermal conductivity when compared with a nearly unimodal particle size distribution of CP 16/30 between 50 and 300 °C. Two different porosity and effective thermal conductivity models were studied, with one providing better prediction of porosity but both effective thermal conductivity models providing less predictive capacity. Importantly this approach can have a substantial impact of thermal performance, with little to no impact on the particle cost.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Simulant Development of Potential 200 West Area Waste Feeds

Preliminary planning for retrieval, qualification, and pretreatment of waste in Hanford’s 200 West Area (200W) has begun as part of the West Area Risk Management project. Experimental studies to technically mature pretreatment process operations will likely be needed because of the uniqueness of 200W waste. Pacific Northwest National Laboratory formulated five simulants to represent 200W-qualified feed based on the preliminary flowsheet provided by Washington River Protection Solutions, LLC. The simulant recipes were devised using applicable historical information as a reference point to support the use of the flowsheet waste vectors, which were combined into five distinct groups. These five groups formed the basis for the liquid composition targets that were adapted into recipes using charged-balanced salt species. The liquid phase recipes were batched in 1-L quantities and analyzed at Pacific Northwest National Laboratory. Once confirmed to be stable, the liquid solutions were tested for compatibility with candidate solid components. Specific solid components were recommended based on cross-examining the proposed solid phases in the flowsheet with relevant data from the literature. Mixtures of solid components were added to aliquots of the liquid batches and sub-sampled to measure particle size distribution. The measured distribution was compared to independently created benchmark distributions appropriate for each simulant. This process was iterated until a solid phase composition that resulted in a representative particle size distribution was found. After the final compositions were confirmed, a suite of chemical and physical characterization data was collected. This report describes the simulant basis, formulation methodology, laboratory measurements, and data collected for the recipes recommended to represent 200W waste feeds.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

A versatile machine learning workflow for high-throughput analysis of supported metal catalyst particles

Accurate and efficient characterization of nanoparticles (NPs), particularly regarding particle size distribution, is essential for advancing our understanding of their structure-property relationship and facilitating their design for various applications. In this study, we introduce a novel two-stage artificial intelligence (AI)-driven workflow for NP analysis that leverages prompt engineering techniques from state-of-the-art single-stage object detection and large-scale vision transformer (ViT) architectures. This methodology is applied to transmission electron microscopy (TEM) and scanning TEM (STEM) images of heterogeneous catalysts, enabling high-resolution, high-throughput analysis of particle size distributions for supported metal catalyst NPs. The model's performance in detecting and segmenting NPs is validated across diverse heterogeneous catalyst systems, including various metals (Ru, Cu, PtCo, and Pt), supports (silica (SiO 2 ), γ-alumina (γ-Al 2 O 3 ), and carbon black), and particle diameter size distributions with mean and standard deviations ranging from 1.6 ± 0.2 nm to 9.7 ± 4.6 nm. The proposed machine learning (ML) methodology achieved an average F1 overlap score of 0.91 ± 0.01 and demonstrated the ability to disentangle overlapping NPs anchored on catalytic support materials. The segmentation accuracy is further validated using the Hausdorff distance and robust Hausdorff distance metrics, with the 90th percent of the robust Hausdorff distance showing errors within 0.4 ± 0.1 nm to 1.4 ± 0.6 nm. In conclusion, our AI-assisted NP analysis workflow demonstrates robust generalization across diverse datasets and can be readily applied to similar NP segmentation tasks without requiring costly model retraining.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

CACTI: Best Estimate Aerosol Size Distribution by airborne measurements

These data were collected during the Cloud, Aerosol, and Complex Terrain Interactions (CACTI; https://www.arm.gov/research/campaigns/amf2018cacti ) field campaign in the Sierras de Córdoba mountain range of north-central Argentina as part of ARM Aerial Facility (AAF) deployment. The ARM Aerial Facility Gulfstream-1 was operated from Las Higueras Airport (IATA: RCU, ICAO: SAOC), Río Cuarto, Córdoba, Argentina, for the Intensive Observation Period (IOP) from Nov. 1 through Dec. 15, 2018. The G-1 aircraft performed 22 research flights over the first ARM Mobile Facility (AMF1) location in the Sierras de Córdoba mountain range to measure atmospheric state and turbulence, cloud water content and droplet size distributions, aerosol precursor gases, aerosol chemical composition and size distributions. The current data set presents Best Estimate Aerosol Size Distribution: a merged aerosol size distribution composed of the data from 5 sensors; three aerosol spectrometers: Scanning Mobility Particle Sizer (SMPS), Ultra-High Sensitivity Aerosol Spectrometer (UHSAS), and Passive Cavity Aerosol Spectrometer (PCASP); and two cloud probes: Cloud Aerosol Spectrometer (CAS) and Fast Cloud Droplet Probe (FCDP). The SMPS data were interpolated to 1 second from “native” time resolution of about 64 second to match all other probes.

54 ENVIRONMENTAL SCIENCES↗