Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PRODUCTION ENGINEERING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS2009

Actively Controlled Components

Active Control can help to meet future engine requirements by an active improvement of the component characteristics. The concept is based on an intelligent control logic, which senses actual operating conditions and reacts with adequate actuator action. This approach can directly improve engine characteristics as performance, operability, durability and emissions on the one hand. On the other hand active control addresses the design constrains imposed by unsteady phenomena like inlet distortion, compressor surge, combustion instability, flow separations, vibration and noise, which only occur during exceptional operating conditions. The feasibility and effectiveness of active control technologies have been demonstrated in lab-scale tests. This chapter describes a broad range of promising applications for each engine component. Significant efforts in research and development remain to implement these technologies in engine rig and finally production engines and to demonstrate today s engine generation airworthiness, safety, reliability, and durability requirements. Active control applications are in particular limited by the gap between available and advanced sensors and actuators, which allow an operation in the harsh environment in an aero engine. The operating and performance requirements for actuators and sensors are outlined for each of the gas turbine sections from inlet to nozzle.

W. Horn↗
DOE OSTI2021

Developing Multi-Gene CRISPRa/I Programs to Accelerate DBTL Cycles in ABF Hosts Engineered for Chemical Production (CRADA 468)

Bacterial metabolism is comprised of large and complex gene networks that can produce valuable chemical products. Sophisticated organism engineering efforts are required to optimize production of high-value compounds from these networks. In principle, synthetic multi-gene transcriptional programs could be constructed to reengineer these networks for efficient industrial chemical production. In practice, however, our incomplete ability to understand and model the underlying networks, combined with our limited ability to predictably control the expression of multiple genes makes achieving this goal difficult. To overcome these challenges, we will combine new CRISPR-Cas multi-gene expression programs with computational modeling, machine learning, and multi-omics data to enhance the efficacy of design-build-test-learn (DBTL) cycles. For industrially promising microorganisms in early stages of development, creating technologies for rapidly engineering complex multi-gene programs could be transformative for accelerating data- and model-driven strain design. New CRISPR-Cas tools allow programmable gene activation (CRISPRa) or repression (CRISPRi) at multiple genes simultaneously, using the catalytically inactive Cas9 protein (dCas9) with guide RNAs that recognize DNA targets through predictable Watson-Crick base pairing. To enable accelerated DBTL cycles, we will combine these technologies with advanced Agile BioFoundry (ABF) capabilities for multi-omics data collection and machine learning. We will demonstrate the immediate applicability of these tools by rapidly improving the production of an industrial aromatic in multiple ABF organisms. We recently identified and optimized new transcriptional activators that can be linked to programmable CRISPR-Cas DNA binding domains to activate gene expression in E. coli. We can now use these CRISPRa tools as generalizable trans-acting regulators for combinatorial multi-gene expression tuning that can be easily transferred to new pathways and networks without additional genome engineering. We anticipate these tools will also transfer to new hosts. We have recently found that CRISPRa systems developed in E. coli can be readily ported to Pseudomonas putida, suggesting that multi-gene CRISPRa/i programs for diverse ABF organisms may be within reach.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Heavy-Duty Low-Temperature and Diesel Combustion & Heavy-Duty Combustion Modeling (FY 2018 Annual Progress Report)

Regulatory drivers and market demands for lower pollutant emissions, lower carbon dioxide emissions, and lower fuel consumption motivate the development of clean and fuel-efficient engine operating strategies. Most current production engines use a combination of both in-cylinder and exhaust emission control strategies to achieve these goals. The emissions and efficiency performance of in-cylinder strategies depend strongly on flow and mixing processes associated with fuel injection. Both heavy- and light-duty engine/vehicle manufacturers use multiple-injection strategies to reduce noise, emissions, and fuel consumption. For both conventional and low-temperature diesel combustion, the state of knowledge and modeling tools for multiple injections are far less advanced than for single-injection strategies. Engine efficiency is limited to some degree by tradeoffs that must be accepted to meet particulate matter (including soot) emissions limits. Recent work on this project has filled some knowledge gaps on soot oxidation with multiple injections, and the current work for Fiscal Year (FY) 2018 addresses knowledge gaps on soot formation for multiple injections. While total in-cylinder soot is readily measured, discerning formation from oxidation is difficult. The FY 2018 experiments are designed to create in-cylinder conditions at the threshold of soot formation, where processes that affect soot formation can be more readily discerned. Soot formation pathways under such conditions are fraught with uncertainties, and soot models significantly overpredict polyaromatic hydrocarbon (PAH) and soot, so experimental data at these conditions will provide much needed data for improvements to PAH and soot models.

02 PETROLEUM↗
NASA NTRS1996

Spherical Joint Piston and Connecting Rod Developed

Under an interagency agreement with the Department of Energy, the NASA Lewis Research Center manages a Heavy-Duty Diesel Engine Technology (HDET) research program. The overall program objectives are to reduce fuel consumption through increased engine efficiency, reduce engine exhaust emissions, and provide options for the use of alternative fuels. The program is administered with a balance of research contracts, university research grants, and focused in-house research. The Cummins Engine Company participates in the HDET program under a cost-sharing research contract. Cummins is researching and developing in-cylinder component technologies for heavy-duty diesel engines. An objective of the Cummins research is to develop technologies for a low-emissions, 55-percent thermal efficiency (LE-55) engine. The best current-production engines in this class achieve about 46-percent thermal efficiency. Federal emissions regulations are driving this technology. Regulations for heavy duty diesel engines were tightened in 1994, more demanding emissions regulations are scheduled for 1998, and another step is planned for 2002. The LE-55 engine emissions goal is set at half of the 1998 regulation level and is consistent with plans for 2002 emissions regulations. LE-55 engine design requirements to meet the efficiency target dictate a need to operate at higher peak cylinder pressures. A key technology being developed and evaluated under the Cummins Engine Company LE-55 engine concept is the spherical joint piston and connecting rod. Unlike conventional piston and connecting rod arrangements which are joined by a pin forming a hinged joint, the spherical joint piston and connecting rod use a ball-and-socket joint. The ball-and-socket arrangement enables the piston to have an axisymmetric design allowing rotation within the cylinder. The potential benefits of piston symmetry and rotation are reduced scuffing, improved piston ring sealing, improved lubrication, mechanical and thermal load symmetry, reduced bearing stresses, reduced running clearances, and reduced oil consumption. The spherical joint piston is a monolithic, squeeze-cast, fiber-reinforced aluminum piston. The connecting rod has a ball end that seats on a spherical saddle within the piston and is retained by a pair of aluminum bronze holder rings. The holder rings are secured by a threaded ring that mates with the piston. As part of the ongoing research and development activity, the Cummins Engine Company successfully completed a 100-hr test of the spherical joint piston and connecting rod at LE- 55 peak steady-state engine conditions. In addition, a 100-hr transient cycle test that varied engine conditions between LE-55 no-load and LE-55 full-load was successfully completed.

Source record↗
NASA NTRS2008

Development Status of the CECE Cryogenic Deep Throttling Demonstrator Engine

As one of the first technology development programs awarded by NASA under the U.S. Space Exploration Policy (USSEP), the Pratt & Whitney Rocketdyne (PWR) Deep Throttling, Common Extensible Cryogenic Engine (CECE) program was selected by NASA in November 2004 to begin technology development and demonstration toward a deep throttling, cryogenic engine supporting ongoing trade studies for NASA's Lunar Lander descent stage. The CECE program leverages the maturity and previous investment of a flight-proven hydrogen/oxygen expander cycle engine, the PWR RLI0, to develop and demonstrate an unprecedented combination of reliability, safety, durability, throttlability, and restart capabilities in a high-energy, cryogenic engine. The testbed selected for the deep throttling demonstration phases of this program was a minimally modified RL10 engine, allowing for maximum current production engine commonality and extensibility with minimum program cost. Two series of demonstrator engine tests, the first in April-May 2006 and the second in March-April 2007, have demonstrated in excess of 10:1 throttling of the hydrogen/oxygen expander cycle engine. Both test series have explored a combustion instability ("chug") environment at low throttled power levels. These tests have provided an early demonstration of an enabling cryogenic propulsion concept with invaluable system-level technology data acquisition toward design and development risk mitigation for future CECE Demonstrator engine tests.

Source record↗
NASA NTRS2007

CECE: A Deep Throttling Demonstrator Cryogenic Engine for NASA's Lunar Lander

As one of the first technology development programs awarded under NASA's Vision for Space Exploration, the Pratt & Whitney Rocketdyne (PWR) Deep Throttling, Common Extensible Cryogenic Engine (CECE) program was selected by NASA in November 2004 to begin technology development and demonstration toward a deep throttling, cryogenic Lunar Lander engine for use across multiple human and robotic lunar exploration mission segments with extensibility to Mars. The CECE program leverages the maturity and previous investment of a flight-proven hydrogen/oxygen expander cycle engine, the RL10, to develop and demonstrate an unprecedented combination of reliability, safety, durability, throttlability, and restart capabilities in a high-energy, cryogenic engine. NASA Marshall Space Flight Center and NASA Glenn Research Center personnel were integral design and analysis team members throughout the requirements assessment, propellant studies and the deep throttling demonstrator elements of the program. The testbed selected for the initial deep throttling demonstration phase of this program was a minimally modified RL10 engine, allowing for maximum current production engine commonality and extensibility with minimum program cost. In just nine months from technical program start, CECE Demonstrator No. 1 engine testing in April/May 2006 at PWR's E06 test stand successfully demonstrated in excess of 10:1 throttling of the hydrogen/oxygen expander cycle engine. This test provided an early demonstration of a viable, enabling cryogenic propulsion concept with invaluable system-level technology data acquisition toward design and development risk mitigation for both the subsequent CECE Demonstrator No. 2 program and to the future Lunar Lander Design, Development, Test and Evaluation effort.

Giuliano, Victor J.↗
NASA NTRS2010

CECE: Expanding the Envelope of Deep Throttling Technology in Liquid Oxygen/Liquid Hydrogen Rocket Engines for NASA Exploration Missions

As one of the first technology development programs awarded by NASA under the Vision for Space Exploration, the Pratt & Whitney Rocketdyne (PWR) Deep Throttling, Common Extensible Cryogenic Engine (CECE) program was selected by NASA in November 2004 to begin technology development and demonstration toward a deep throttling, cryogenic engine supporting ongoing trade studies for NASA s Lunar Lander descent stage. The CECE program leverages the maturity and previous investment of a flight-proven hydrogen/oxygen expander cycle engine, the PWR RL10, to develop and demonstrate an unprecedented combination of reliability, safety, durability, throttlability, and restart capabilities in high-energy, cryogenic, in-space propulsion. The testbed selected for the deep throttling demonstration phases of this program was a minimally modified RL10 engine, allowing for maximum current production engine commonality and extensibility with minimum program cost. Four series of demonstrator engine tests have been successfully completed between April 2006 and April 2010, accumulating 7,436 seconds of hot fire time over 47 separate tests. While the first two test series explored low power combustion (chug) and system instabilities, the third test series investigated and was ultimately successful in demonstrating several mitigating technologies for these instabilities and achieved a stable throttling ratio of 13:1. The fourth test series significantly expanded the engine s operability envelope by successfully demonstrating a closed-loop control system and extensive transient modeling to enable lower power engine starting, faster throttle ramp rates, and mission-specific ignition testing. The final hot fire test demonstrated a chug-free, minimum power level of 5.9%, corresponding to an overall 17.6:1 throttling ratio achieved. In total, these tests have provided an early technology demonstration of an enabling cryogenic propulsion concept with invaluable system-level technology data acquisition toward design and development risk mitigation for future lander descent main engines.

Giuliano, Victor J.↗
NASA NTRS2010

CECE: Expanding the Envelope of Deep Throttling in Liquid Oxygen/Liquid Hydrogen Rocket Engines For NASA Exploration Missions

As one of the first technology development programs awarded by NASA under the Vision for Space Exploration, the Pratt & Whitney Rocketdyne (PWR) Deep Throttling, Common Extensible Cryogenic Engine (CECE) program was selected by NASA in November 2004 to begin technology development and demonstration toward a deep throttling, cryogenic engine supporting ongoing trade studies for NASA s Lunar Lander descent stage. The CECE program leverages the maturity and previous investment of a flight-proven hydrogen/oxygen expander cycle engine, the PWR RL10, to develop technology and demonstrate an unprecedented combination of reliability, safety, durability, throttlability, and restart capabilities in a high-energy cryogenic engine. The testbed selected for the deep throttling demonstration phases of this program was a minimally modified RL10 engine, allowing for maximum current production engine commonality and extensibility with minimum program cost. Three series of demonstrator engine tests, the first in April-May 2006, the second in March-April 2007 and the third in November-December 2008, have demonstrated up to 13:1 throttling (104% to 8% thrust range) of the hydrogen/oxygen expander cycle engine. The first two test series explored a propellant feed system instability ("chug") environment at low throttled power levels. Lessons learned from these two tests were successfully applied to the third test series, resulting in stable operation throughout the 13:1 throttling range. The first three tests have provided an early demonstration of an enabling cryogenic propulsion concept, accumulating over 5,000 seconds of hot fire time over 27 hot fire tests, and have provided invaluable system-level technology data toward design and development risk mitigation for the NASA Altair and future lander propulsion system applications. This paper describes the results obtained from the highly successful third test series as well as the test objectives and early results obtained from a fourth test series conducted over March-May 2010

Giuliano, Victor J.↗
DOE OSTI2024

OPERATION OF FT4000® SINGLE NOZZLE COMBUSTOR WITH HIGH HYDROGEN

This paper reports initial results from an effort to develop a retrofittable fuel/air injector for the FT4000® aeroderivative gas turbine that enables use of hydrogen as a carbon-free fuel for efficient power generation. The FT4000 engine’s low-NOx combustor was developed by Pratt & Whitney and RTX Technology Research Center with core technology from the Pratt & Whitney PW4000 turbofan aircraft engine. The work reported here advances the technology readiness level of the FT4000 combustor for operation with hydrogen, starting with an experimental assessment of the current production hardware with increasing hydrogen content mixed with natural gas. High-pressure single-sector combustor rig tests have been completed, demonstrating the ability for the dual fuel nozzle to operate an FT4000 combustor on 100% hydrogen with low nitrogen oxide (NOx) missions. Metal temperature measurements and video images of the flame structure from zero to 100% hydrogen highlight opportunities to improve the fuel nozzle robustness for high hydrogen conditions. The current FT4000 production engine operates on either natural gas or No. 2 fuel oil with water injection to achieve high thermal efficiency and low emissions. This engine is fielded by Mitsubishi Power Aero and delivers 70 MW of power with a simple-cycle efficiency of over 41% when operating with wet compression. Results from this study have cleared the current production FT4000 engines with dual fuel nozzles to operate at baseload power on blends of hydrogen mixed with natural gas and water.

power generation↗
NASA NTRS1998

Advanced Subsonic Combustion Rig

Researchers from the NASA Lewis Research Center have obtained the first combustion/emissions data under extreme future engine operating conditions. In Lewis' new world-class 60-atm combustor research facility--the Advanced Subsonic Combustion Rig (ASCR)--a flametube was used to conduct combustion experiments in environments as extreme as 900 psia and 3400 F. The greatest challenge for combustion researchers is the uncertainty of the effects of pressure on the formation of nitrogen oxides (NOx). Consequently, U.S. engine manufacturers are using these data to guide their future combustor designs. The flametube's metal housing has an inside diameter of 12 in. and a length of 10.5 in. The flametube can be used with a variety of different flow paths. Each flow path is lined with a high-temperature, castable refractory material (alumina) to minimize heat loss. Upstream of the flametube is the injector section, which has an inside diameter of 13 in. and a length of 0.5-in. It was designed to provide for quick changeovers. This flametube is being used to provide all U.S. engine manufacturers early assessments of advanced combustion concepts at full power conditions prior to engine production. To date, seven concepts from engine manufacturers have been evaluated and improved. This collaborated development can potentially give U.S. engine manufacturers the competitive advantage of being first in the market with advanced low-emission technologies.

Lee, Chi-Ming↗
NASA NTRS2012

Principles to Products: Toward Realizing MOS 2.0

This is a report on the Operations Revitalization Initiative, part of the ongoing NASA-funded Advanced Multi-Mission Operations Systems (AMMOS) program. We are implementing products that significantly improve efficiency and effectiveness of Mission Operations Systems (MOS) for deep-space missions. We take a multi-mission approach, in keeping with our organization's charter to "provide multi-mission tools and services that enable mission customers to operate at a lower total cost to NASA." Focusing first on architectural fundamentals of the MOS, we review the effort's progress. In particular, we note the use of stakeholder interactions and consideration of past lessons learned to motivate a set of Principles that guide the evolution of the AMMOS. Thus guided, we have created essential patterns and connections (detailed in companion papers) that are explicitly modeled and support elaboration at multiple levels of detail (system, sub-system, element...) throughout a MOS. This architecture is realized in design and implementation products that provide lifecycle support to a Mission at the system and subsystem level. The products include adaptable multi-mission engineering documentation that describes essentials such as operational concepts and scenarios, requirements, interfaces and agreements, information models, and mission operations processes. Because we have adopted a model-based system engineering method, these documents and their contents are meaningfully related to one another and to the system model. This means they are both more rigorous and reusable (from mission to mission) than standard system engineering products. The use of models also enables detailed, early (e.g., formulation phase) insight into the impact of changes (e.g., to interfaces or to software) that is rigorous and complete, allowing better decisions on cost or technical trades. Finally, our work provides clear and rigorous specification of operations needs to software developers, further enabling significant gains in productivity.

AMMOS↗
NASA NTRS1985

Improving engineering effectiveness

Methodologies to improve engineering productivity were investigated. The rocky road to improving engineering effectiveness is reviewed utilizing a specific semiconductor engineering organization as a case study. The organization had a performance problem regarding new product introductions. With the help of this consultant as a change agent the engineering team used a systems approach to through variables that were effecting their output significantly. Critical factors for improving this engineering organization's effectiveness and the roles/responsibilities of management, the individual engineers and the internal consultant are discussed.

Fiero, J. D.↗
DOE OSTI2019

Development and Validation of Predictive Models for In-Cylinder Radiation and Wall Heat Transfer

The lack of accurate submodels for in-cylinder radiation and heat transfer has been identified as a key shortcoming in developing truly predictive, physics-based computational fluid dynamics (CFD) models that can be used to develop and design combustion systems for advanced high-efficiency, low-emissions engines. Measurements of wall boundary layers in engines show discrepancies of up to 100% with respect to standard CFD boundary layer models. And analysis of in-cylinder radiation based on the most recent spectral property databases and high-fidelity radiative transfer equation solvers has shown that at operating pressures and exhaust-gas recirculation levels typical of modern compression-ignition truck engines, molecular gas radiation (mainly carbon dioxide and water vapor) can be more important than soot particle radiation, and that a significant fraction of the emitted radiation (50% or more) can be reabsorbed before reaching the walls, thereby acting to redistribute energy in the combustion chamber. In this project, an integrated experimental and simulation approach has been used to generate new physical insight into in-cylinder heat-transfer processes in engines, and to develop computationally practicable CFD-based models that accurately represent the physics. New experimental data have been taken in an optically accessible single-cylinder research engine, and in a multi-cylinder production engine. Those data have provided new insight into the radiative environment in engines. New CFD models have been developed and validated for in-cylinder heat transfer, focusing mainly on radiative heat transfer and coupling between turbulent boundary layer wall heat transfer and radiative heat transfer. The CFD models have been developed and implemented in an open-source software framework that can be shared with other researchers. The models are compatible both with unsteady Reynolds-averaged Navier Stokes (URANS) formulations and with large-eddy simulations (LES) of in-cylinder processes in engines.

02 PETROLEUM↗
DOE OSTI2023

Engineering Computational Practices (Rev. 1)

This manual will attempt to motivate the use of an automated build system for the purposes of computational science and engineering. As part of this motivation, the surrounding computational practices of version control, documen tation, compute environment management, and regression testing will also be addressed as applied to the practice of computational engineering. Specifically, this manual intends to motivate the adoption of these traditional software engineering practices for use in research and production engineering simulation projects. This manual is not the first such effort in the greater scientific computing community. In fact, the authors relied heavily on the lesson plans of the Software Carpentry, established to teach computing skills to researchers in 1998. As the intention for this manual is to lay out fundamental practices of engineering computing, it will not attempt to fully teach the underlying concepts and will instead reference the well designed lesson plans of the Software Carpentry. Where possible, this manual will explain to general computing practices and concepts and limit discussion of specific software implementations to examples or vehicles for practice in concrete application. The specific software taught by the Software Carpentry curriculum is an excellent starting point to learn the core concepts of computational engi neering. However, the authors have found that applications to engineering simulation and analysis require translation of these software development concepts into the language and workflows of computational engineers. Adopting these computational tools may require engineers to re-imagine their workflows in some combination of traditional engineer ing and software concepts. It has also been necessary to extend existing software build systems for engineering practices beyond the simple wrap ping of engineering software execution. Where necessary, examples of specific software and their method of extension to engineering simulations will be given, with reference to the User Manual for recommended practical use. Where this manual relies on specific implementation examples, it should be understood that the practicing engineer may find that different software is more amenable to their specific work. It is always the overall collection of computational practices is more important than any specific software implementation. The ability to recognize which concepts are implemented by a software package will make a practicing engineer agile to changing project needs, computing resources, numeric solvers, programming languages, and even available funding.

42 ENGINEERING↗
NASA NTRS1990

Computer aided system engineering and analysis (CASE/A) modeling package for ECLS systems - An overview

An overview of the CASE/A-ECLSS series modeling package is presented. CASE/A is an analytical tool that has supplied engineering productivity accomplishments during ECLSS design activities. A components verification program was performed to assure component modeling validity based on test data from the Phase II comparative test program completed at the Marshall Space Flight Center. An integrated plotting feature has been added to the program which allows the operator to analyze on-screen data trends or get hard copy plots from within the CASE/A operating environment. New command features in the areas of schematic, output, and model management, and component data editing have been incorporated to enhance the engineer's productivity during a modeling program.

Dalee, Robert C.↗
NASA NTRS1985

Current and future engine applications of Gr/PI composites

The application of organic matrix composites to gas turbine engine components has been the subject of numerous government and company funded programs since the 1960's. The possibility of significant weight reductions, performance improvements and lower component costs have made the organic matrix composites extremely attractive to aircraft engine designers. Very little of this potential was incorporated into production engines over the years even though a significant number of components were designed, fabricated and tested. Some of the reasons behind the slow rate of incorporation include the following: (1) criticality; (2) engine operating temperature; (3) small component size; (4) small production volume; (5) high production cost; and (6) interfacing with metal parts.

Cavano, P. J.↗
DOE OSTI2020

Combining Random Mutagenesis and Metabolic Engineering for Enhanced Tryptophan Production in Synechocystis sp. Strain PCC 6803

Tryptophan (Trp) is an essential aromatic amino acid that has value as an animal feed supplement, as the amount found in plant-based sources is insufficient. An alternative to production by engineered microbial fermentation is to have tryptophan biosynthesized by a photosynthetic microorganism that could replace or supplement both the plant and industrially used microbes. We selected Synechocystis sp. strain PCC 6803, a model cyanobacterium, as the host and studied metabolic engineering and random mutagenesis approaches. Previous work on engineering heterotrophic microbes for improved Trp titers has targeted allosteric feedback regulation in enzymes 3-deoxy-d-arabinoheptulosonate 7-phosphate synthase (DAHPS) and anthranilate synthase (AS) as major bottlenecks in the shikimate pathway. In this work, the genes encoding feedback-resistant enzymes from Escherichia coli, aroG fbr and trpE fbr , were overexpressed in the host wild-type (WT) strain. Separately, the WT strain was subjected to random mutagenesis and selection using an amino acid analog to isolate tryptophan-overproducing strains. The randomly mutagenized strains were sequenced in order to identify the mutations that resulted in the desirable phenotypes. Interestingly, the tryptophan overproducers had mutations in the gene encoding chorismate mutase (CM), which catalyzes the conversion of chorismate to prephenate. The best tryptophan overproducer from random mutagenesis was selected as a host for metabolic engineering where aroG fbr and trpE fbr were overexpressed. The best strain developed produced 212 ± 23 mg/liter of tryptophan after 10 days of photoautotrophic growth under 3% (vol/vol) CO2. We demonstrated that a combination of random mutagenesis and metabolic engineering was superior to either individual approach.

59 BASIC BIOLOGICAL SCIENCES↗