Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PRESSING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

Modeling the thermal deformation of TATB-based explosives. Part 1: Thermal expansion of “neat-pressed” polycrystalline TATB

We detail a modeling approach to simulate the anisotropic thermal expansion of polycrystalline (1,3,5-triamino-2,4,6-trinitrobenzene) TATB-based explosives that utilizes microstructural information including porosity, crystal aspect ratio, and processing-induced texture. This report, the first in a series, focuses on nonlinear thermal expansion of “neat-pressed” polycrystalline TATB specimens which do not contain any binder; additional complexities related to polymeric binder and irreversible ratcheting behavior are briefly discussed, however detailed investigation of these aspects are deferred to subsequent reports. In this work we have, for the first time, developed a mesoscale continuum model relating the thermal expansion of polycrystal TATB specimens to their microstructural characteristics. A self-consistent homogenization procedure is used to relate macroscopic thermoelastic response to the constitutive behavior of single-crystal TATB. The model includes a representation of grain aspect ratio, porosity, and crystallographic texture attributed to the consolidation process. A quantitative model is proposed to describe the evolution of preferred orientation of graphitic planes in TATB during consolidation and an algorithm constructed to develop a discrete representation of the associated orientation distribution function. Analytical and numerical solutions using this model are shown to produce textures consistent with previous measurements and characterization for isostatic and uniaxial “die-pressed” specimens. Predicted thermal strain versus temperature for textured specimens are shown to be in agreement with corresponding experimental measurements. Using the developed modeling approach, several simulations have been run to investigate the influence of microstructure on macroscopic thermal expansion behavior. Results from these simulations are used to identify qualitative trends. Implications of the identified trends are discussed in the context of thermal deformation of engineered components whose consolidation process is generally more complex than isostatic or die-pressed specimens. Finally, an envisioned application of the modeling approach to simulating thermal expansion of weapon systems and components is outlined along with necessary future work to introduce the effects of binder and ratcheting behavior. Key conclusions from this work include the following. Both porosity and grain aspect ratio have an influence on the thermal expansion of polycrystal TATB considering realistic material variability. Thepreferred orientation of the single crystal TATB [001] poles within a polycrystal gives rise to pronounced anisotropy of the macroscopic thermal expansion. The extent of this preferred orientation depends on the magnitude of deformation, and consequently, is expected to vary spatially throughout manufactured components much like porosity. The modeling approach presented here has utility toward bringing spatially variable microstructural features into macroscale system engineering modelsAbstract Not Provided

36 MATERIALS SCIENCE↗

A Thermal Control System for an Isostatic Press

This paper proposes a concept of operation for an isostatic pressing capability using a proposed thermally controlled system developed using system engineering methodology. The concept utilizes a computer controlled fluid based heat exchange system capable of heating or cooling a pressure vessel in which high explosive (HE) is isostatically pressed. A press operator controls the system through a computer interface.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Thermal Test on Target with Pressed Disks

A thorough test of the thermal performance of a target for Mo 99 production using solid Mo 100 target to produce the Mo 99 via a gamma-n reaction has previously been conducted at Argonne National Laboratory (ANL). The results are reported in “Zero Degree Line Mo Target Thermal Test Results and Analysis,” LANL report Number LA-UR-15-23134 dated 3/27/15. This target was comprised of 25 disks 1 mm thick and 12 mm in diameter, separated by helium coolant gaps 0.5 mm wide. The test reported in the above referenced report was conducted with natural Mo disks all cut from commercial rod. The production plant will have Mo 100 disks pressed and sintered using a process being developed at Oak Ridge National Laboratory (ORNL). The structural integrity of press-and-sinter disks is of some concern. The test reported herein included 4 disks made by the ORNL process and placed in the high heat, and therefore high thermal stress, region of the target. The electron beam energy was 23 MeV for these tests. Beam spot size was 3.5 mm horizontal and 3 mm vertical, FWHM. The thermal stress test of pressed-and-sintered disks resulted in no mechanical failures. The induced thermal stresses were below yield stress for natural Mo, indicating that up to that stress state no inherent deficiencies in the mechanical properties of the fabricated disks were evident.

07 ISOTOPE AND RADIATION SOURCES↗

A high-fidelity model for coupling flow and mechanical deformation of the porous paper web - a key to improved understanding of dewatering and rewet at the press section in paper making

The U.S. pulp and paper industry is the third-largest manufacturing user of energy, with an energy demand of 2,540 trillion Btu in 2010. Within the papermaking process, drying consumes over 400 trillion Btu annually which makes it one of the largest energy saving opportunities. In the 2014 Forest Products Industry Technology Roadmap, it is concluded that increasing the paper web solid content entering the dryer section from the current 45- 55 percent to approaching 65 percent, which would save 1.0 MMBtu per ton or 20 percent of the energy used in drying, is one of the most needed technology breakthroughs to achieve a more sustainable approach for manufacturing pulp and paper products. Achieving such significant energy savings highly depends on understanding the fundamental dynamics of the wet press process and then developing optimized solutions for design of more energy-efficient press processes and equipment. The objective of this project is to develop reliable computational capabilities to accurately simulate the flow of water from/to the porous pulp medium (dewatering/rewetting) during the pressing process in paper making.

42 ENGINEERING↗

TA-03-0035 Press Building – D&D

The Press Building was constructed in 1954 with 15,073 ft 2 of floor space. It was built to house a 5000 ton double action Lake Erie hydraulic press and a uranium casting area. Missions included uranium activities associated with the Nuclear Weapons and Rover Rocket programs. At the end of the Rover program, the building continued to support various uranium materials science projects until the building was placed into a cold and dark status in 2013 and then was demolished in 2017. The building interior, the press, and associated systems were radiological contaminated and disposed of as low level waste. The demolition of this building opened up valuable real estate in the TA-3 area for the future construction of an ~11,000 Sq. Ft. Biosafety Level 2 laboratory and office building. This building will support the ongoing Bioscience Division mission at the laboratory.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Hot Press Market Study

A study has been conducted to identify vendors for a hot press suitable for meeting program deliverables chiefly to achieve a higher TRL for the material and process. This study identities the high level specifications for the hot press which must be able to produce samples to support both the fabrication method development and fabricate full size components for testing to demonstrate success. Three vendors capable of meeting hot press specifications were contacted and estimates were obtained. A comparison of the equipment was performed and a recommendation is made for equipment acquisition.

36 MATERIALS SCIENCE↗

Zirconium Carbide Produced by Spark Plasma Sintering and Hot Pressing: Densification Kinetics, Grain Growth, and Thermal Properties

Spark plasma sintering (SPS) has been employed to consolidate a micron-sized zirconium carbide (ZrC) powder. ZrC pellets with a variety of relative densities are obtained under different processing parameters. The densification kinetics of ZrC powders subjected to conventional hot pressing and SPS are comparatively studied by applying similar heating and loading profiles. Due to the lack of electric current assistance, the conventional hot pressing appears to impose lower strain rate sensitivity and higher activation energy values than those which correspond to the SPS processing. A finite element simulation is used to analyze the temperature evolution within the volume of ZrC specimens subjected to SPS. The control mechanism for grain growth during the final SPS stage is studied via a recently modified model, in which the grain growth rate dependence on porosity is incorporated. Finally, the constant pressure specific heat and thermal conductivity of the SPS-processed ZrC are determined to be higher than those reported for the hot-pressed ZrC and the benefits of applying SPS are indicated accordingly.

36 MATERIALS SCIENCE↗

Constitutive Behavior and Hot Workability of a Hot Isostatic Pressed Ti-22Al-25Nb Alloy during Hot Compression

A Ti-22Al-25Nb alloy was fabricated from prealloyed powders by hot isostatic pressing for 2 h at a temperature of 1050 °C and pressure of 100 MPa. The hot deformation behavior of the Ti-22Al-25Nb alloy was characterized by isothermal compression testing at deformation temperatures between 900 and 1060 °C and strain rates between 0.001 and 1 s{sup −1}. Based on the true stress–strain curves, a constitutive equation was constructed to describe the flow stress as a function of the strain rate and deformation temperature. Three-dimensional (3D) processing maps were developed based on dynamic material model theory using the stress flow data to identify the instability and optimization regions of the hot processing parameters. The results show that the flow stress decreases with increasing deformation temperature and decreasing strain rate, and the softening mechanisms are different under different deformation conditions. The apparent activation energies in the (α{sub 2} + β/B2 + O) and (α{sub 2} + B2) phase regions are calculated to be 865.177 and 590.661 kJ/mol, respectively, which suggests that the hot isostatic pressed (HIPed) Ti-22Al-25Nb alloy requires a high hot deformation activation energy. Combined with microstructural observations, the optimal processing domains are determined to be a temperature range of 1030-1060 °C and strain rate range of 0.01-0.1 s{sup −1} in the α{sub 2} + B2 phase region. Moreover, the results indicate that adiabatic shear bands and severe inhomogeneous deformation cause flow instability at lower temperatures (900-1005 °C) and higher strain rates (> 0.1 s{sup −1}).

36 MATERIALS SCIENCE↗

Numerical Simulation of Cold Pressing of Armstrong CP-Ti Powders

Numerical simulation results for the cold pressing of Armstrong CP-Ti Powders are presented. The computational model was implemented in the commercial finite element program ABAQUSTM. Several simulation cases were conducted for cylindrical samples with different friction coefficients and different compaction pressures, under both single-action and dual-action uniaxial pressing. Numerical simulation results for the density distribution are compared against experimental data in order to validate the computational model.

36 MATERIALS SCIENCE↗

A Facile, Low-Cost Hot-Pressing Process for Fabricating Lithium-Sulfur Cells with Stable Dynamic and Static Electrochemistry

Lithium–sulfur batteries are among the most promising low-cost, high-energy-density storage devices. However, the inability to host a sufficient amount of sulfur in the cathode while maintaining good electrochemical stability under a lean electrolyte condition has limited the progress. The main cause of these challenges is the sensitivity of the sulfur cathode to the cell-design parameters (i.e., the amount of sulfur and electrolyte) and the experimental testing conditions (i.e., cycling rates and analysis duration). Here, a hot-pressing method is presented that effectively encapsulates a high amount of sulfur in the cathode within only 5 s, resulting in high sulfur loading and content of, respectively, 10 mg cm -2 and 65 wt%. The hot-pressed sulfur (HPS) cathodes exhibit superior dynamic and static electrochemical performance under a broad cycling-rate (C/20–1C rates) and low electrolyte/sulfur ratio (6 µL mg -1 ) conditions. The dynamic cell stability is demonstrated by high gravimetric and areal capacities of, respectively, 415–730 mAh g -1 and 7–12 mAh cm -2 at C/20–1C rates with a high capacity retention of over 70% after 200 cycles. As a result, the static cell stability is demonstrated by excellent shelf life with low self-discharge and stable cycle life on storing for over one year.

25 ENERGY STORAGE↗

New coal char-based bricks: Effects of curing temperature, humidity, pressing pressure, and addition of superplasticizer on the physical, mechanical, and thermal properties

Coal char, as a sustainable and eco-friendly material, holds significant potential for use in new construction materials, specifically, coal char-based bricks. This study employed the pre-pressing method to create char bricks containing high char content of 70%. The impact of various curing temperatures (20, 40, 60 °C), humidity levels (15% and 90%), and pressing pressures (3.5, 7, and 10 MPa) on the density, X-ray diffraction, compressive strength, and thermal conductivity of char-based samples were examined. The addition of superplasticizer and the performance of char bricks were assessed by comparing them to traditional clay bricks and corresponding standards. The study discovers that the temperature of 40 °C enhances the early 7-day strength of char brick samples, while the highest 28-day strength is observed in char bricks at a temperature of 20 °C and humidity of 90%. Compared to conventional clay bricks (with density of 1.9 g/cm3, thermal conductivity of 0.39-0.63 W/mK, compressive strength of 10-20 MPa), the proposed char bricks exhibit lower density (~0.8 g/cm 3 ), lower thermal conductivity (0.26-0.35 W/mK), and good performance in compressive strength (up to 15 MPa). Lastly, coal char-based bricks with high char content demonstrate significant advantages over traditional clay bricks, making them a sustainable and environmentally friendly building material option.

36 MATERIALS SCIENCE↗

The investigation of die-pressing and sintering behavior of ITP CP-Ti and Ti-6Al-4V powders

This paper investigated the die-pressing and sintering behavior of the low-cost CP-Ti and Ti-6Al- 4V powders made by the Armstrong Process . The Armstrong powders have an irregular coral like, dendritic morphology, with a dendrite size of approximately 2-5 m. As-received as well as milled powders were uniaxially pressed at designated pressures up to 690 MPa to form disk samples with different aspect ratios. In the studied pressure range, an empirical powder compaction equation was applied to linearize the green density pressure relationship, and powder compaction parameters were obtained. The Armstrong Ti-64 powder exhibited a significantly higher sinterability than the CP-Ti powder. This was explained to be due to the higher diffusivity of V at the sintering temperature. The Ti-64 samples with a green density of 71.0% increased to 99.6% after sintering at 1300oC for 1 hour. An ex-situ technique was used to track the powder morphology change before and after sintering.

36 MATERIALS SCIENCE↗

Additive-free hot-pressed silicon carbide ceramics-A material with exceptional mechanical properties

Densification of silicon carbide without any sintering aids by hot-pressing and rapid hot pressing was investigated. Full density (>99% t.d.) has been reached at 1850 °C, a temperature of at least 150-200 °C lower compared to the up to now known solid state sintered silicon carbide powders. Silicon carbide was freeze granulated and heat treated prior the densification. Furthermore, evolution of microstructure, mechanical properties and creep behavior were evaluated and compared to reference ceramics from as received silicon carbide powder as well as those of commercial one. Novel method results in dense ceramics with Vickers hardness and indentation fracture toughness of 29.0 GPa and 5.25 MPam 1/2 , respectively. Moreover, the creep rate of 3.8 x 10 –9 s –1 at 1450 °C and the load of 100 MPa is comparable to the commercial α-SiC solid state sintered at 2150 °C.

36 MATERIALS SCIENCE↗

Processing of surrogate nuclear fuel pellets for better dimensional control with dry bag isostatic pressing

A study of improved methods of processing fuel pellets was undertaken using ceria and zirconia/yttria/alumina as surrogates. Through proper granulation and vertical vibration (tapping) of the parts bag prior to dry bag isostatic pressing (DBIP), reproducibility of diameter profiles among multiple pellets of ceria was improved by almost an order of magnitude. Reproducibility of sintered pellets was sufficiently good to possibly avoid grinding. Deviation from the mean diameter along the length of multiple pellets, as well as, deviation from roundness, decreased after sintering. This is not generally observed with dry pressed pellets. Thus it is possible to machine to tolerance before sintering if grinding is necessary.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Microstructure and microchemistry changes at U-10Mo fuel/AA6061 cladding interfaces with varying hot isostatic pressing conditions

Monolithic uranium - 10 wt.% molybdenum (U-10Mo) is a promising high-assay low-enriched uranium fuel system for nuclear reactors used in research, medical isotope production, and remote power applications. During manufacturing, AA6061 cladding is bonded to the U-10Mo fuel plate via hot isostatic pressing, during which diffusion and fuel/cladding chemical interaction occurs at plate edges. Furthermore, the microstructure and microchemistry changes that occur at fuel/cladding interfaces are important to understand as a function of process parameters to develop a reliable fuel fabrication process and to meet the desired specifications. Here, microstructural and microchemical changes are studied using complementary electron microscopy and atom probe tomography for two manufactured fuel plates with varied hot isostatic pressing (HIP) parameters. Results highlight that modifying thermomechanical processing parameters significantly changed the interaction layer thickness between U-10Mo and AA6061 by an order of magnitude. In addition to this the distribution and concentration of elements (i.e., Al, Si, Mg) from cladding to fuel was also investigated.

36 MATERIALS SCIENCE↗

Mechanical and microstructural characterization of 6061 aluminum alloy strips severely deformed by Dissimilar Channel Angular Pressing

Dissimilar Channel Angular Pressing (DCAP) is a severe plastic deformation technique to improve the mechanical properties of flat products by producing ultrafine grains. In this study, the changes in the microstructure and mechanical properties of 6061 Al-alloy strips deformed by various numbers of DCAP passes were investigated. Some DCAPed samples were also held at 200 deg. C and 350 deg. C to investigate the effect of post-annealing. Mechanical properties were determined by hardness and tension tests; and microstructural changes were investigated by TEM analysis. Up to a critical level of plastic strain, remarkable improvements have been observed in the strength and hardness of the severely deformed strips; and the improvements have been explained by variations in grain size, dislocation structure, and formation of subgrains. - Research Highlights: {yields}Dissimilar Channel Angular Pressing (DCAP). {yields}Severe plastic deformation (SPD). {yields}Transmission Electron Microscopy of the 6061 Al alloy. {yields}Mechanical Properties of 6061 Al alloy.

36 MATERIALS SCIENCE↗

Fabrication and microstructures of functional gradient SiBCN–Nb composite by hot pressing

A functional gradient material with five layers composed of SiBCN ceramic and niobium (Nb) was prepared successfully by hot pressing. The phase composition, morphology features and microstructures were investigated in each layer of the gradient material. The Nb-containing compounds involving NbC, Nb{sub 6}C{sub 5}, Nb{sub 4}C{sub 3}, Nb{sub 5}Si{sub 3} and NbN increase with the volume fraction of Nb increasing in the sub-layer. They are randomly scattered (≤ 25 vol.% Nb), then strip-like, and finally distribute continuously (≥ 75 vol.% Nb). The size of BN(C) and SiC grains in Nb-containing layers is larger than in 100% SiBCN layer due to the loss of the capsule-like structures. No distinct interfaces form in the transition regions indicating the gradual changes in phase composition and microstructures. - Highlights: • A functional gradient SiBCN–Nb material was prepared successfully by hot pressing. • Phase composition, morphology features and microstructures were investigated. • Thermodynamic calculation was used to aid in the phase analysis. • No distinct interfaces form typical of the functional gradient material.

36 MATERIALS SCIENCE↗

The Performance of CH3NH3PbI3 - Nanoparticles based – Perovskite Solar Cells Fabricated by Facile Powder press Technique

Highlights: • Perovskite nanoparticles (PNs) were prepared using simple solid-state technique. • Perovskite layer has been deposited by facile powder press technique - a solution cum vacuum-free. • Fabricated device structure: FTO/c-TiO{sub 2}/mp-TiO{sub 2}/Perovskite/CuI/Cr/Pt-coated FTO. • 1:3 M ratio of PbI{sub 2} in MAI resulted in achieving a PCE of 3.90%. • From the stability test, it is inferred that deterioration in ‘η’ and ‘V{sub OC}’ was by 27.87% and 29.23% respectively. - Abstract: Here, we have introduced a facile solid-state route assisted method to prepare CH{sub 3}NH{sub 3}PbI{sub 3} perovskite nanoparticles (PNs) and together with a facile - powder press technique, for the deposition of prepared PNs - a solution cum vacuum-free route. The perovskite layer was prepared using different lead iodide (PbI{sub 2}) precursor molar concentrations (0.5, 1, 1.5, 2 mmol) and the PbI{sub 2} concentration was found to have a significant impact on the structural, optical, morphological and electrical properties. The sample prepared using molar ratio PbI{sub 2}: MAI at 1:3 shows the optimal bandgap value (∼1.51 eV), broader band edge peak at 755 nm and found have good optical property for photovoltaic (PV) applications. The J–V performance of the fabricated perovskite device with FTO/c-TiO{sub 2}/mp-TiO{sub 2}/Perovskite/CuI/ Cr/Pt-coated FTO counter electrode has been studied. The device fabricated using the concentration at PbI{sub 2}:MAI 1:3 achieved a PCE of 3.9% and resulted in better long-term stability with deterioration in η and V{sub OC} by 27.87% and 29.23% after 15 days.

14 SOLAR ENERGY↗