Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PAST”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

Effect of Carbon Nanofiber Clustering on the Micromechanical Properties of a Cement Paste

The use of carbon nanofibers (CNFs) in cement systems has received significant interest over the last decade due to their nanoscale reinforcing potential. However, despite many reports on the formation of localized CNF clusters, their effect on the cement paste micromechanical properties and relation to the mechanical response at the macroscopic scale are still not fully understood. In this study, grid nanoindentation coupled with scanning electron microscopy and energy dispersive spectroscopy was used to determine the local elastic indentation modulus and hardness of a portland cement paste containing 0.2% CNFs with sub-micro and microscale CNF clusters. The presence of low stiffness and porous assemblage of phases (modulus of 15–25 GPa) was identified in the cement paste with CNFs and was attributed primarily to the interfacial zone surrounding the CNF clusters. The CNFs favored the formation of higher modulus C–S–H phases (>30 GPa) in the bulk paste at the expense of the lower stiffness C–S–H. Nanoindentation results combined with a microscale–macroscale upscaling homogenization method further revealed an elastic modulus of the CNF clusters in the range from 18 to 21 GPa, indicating that the CNF clusters acted as compliant inclusions relative to the cement paste.

36 MATERIALS SCIENCE↗

Influence of superplasticizers on the rheology and stability of limestone and cement pastes

The influence of superplasticizers on the rheological properties and dynamic stability of cement and reference limestone pastes were examined at room temperature. The pastes were initially formulated to exhibit nearly identical rheological parameters and bleeding-segregation characteristics, with w/c = 0.50 for the limestone and 0.55 for the cement. The former was examined at equilibrium pH {approx} 10 and at pH 12.5 following addition of Ca(OH){sub 2} to allow distinction of effects related to high pH and Ca{sup +2} from those related to cement hydration reactions. Both polynaphthalene- (PNS) and polyacrylate-type (PC) superplasticizers were investigated, adjusting the dosages to cover the same range of paste fluidity. Superplasticizer-particle interactions were monitored through binding isotherms and zeta potential measurements. The rheology of the pastes was evaluated through the mini-slump test and dynamic viscosity measurements which yielded key rheological parameters: yield stress, elastic and loss moduli (G' and G'') and zero-shear viscosity ({eta}{sub 0}). The paste stability was monitored as function of time, i.e. migration of solids and liquid phase measured in-situ and in 'real time', through surface bleeding measurements and from a multipoint conductivity method. The results provide new insight on the relative modes of action of PNS- and PC-type superplasticizers as dispersants. Also, the combined rheology and stability data allow an improved description of the processes responsible for bleeding and segregation in cementitious and reference systems.

36 MATERIALS SCIENCE↗

Sorption kinetics of superabsorbent polymers (SAPs) in fresh Portland cement-based pastes visualized and quantified by neutron radiography and correlated to the progress of cement hydration

Water sorption of two superabsorbent polymers in cement-based pastes has been characterized by neutron radiography. Cement pastes with W/C of 0.25 and 0.50 and one additionally containing silica fume (W/C = 0.42) were investigated. The SAPs differed in their inherent sorption kinetics in extracted cement pore solution (SAP 1: self-releasing; SAP 2: retentive). Desorption from SAP 1 started very early after paste preparation. Hence, its individual non-retentiveness governs its behavior only. SAP 2 released water into all matrices, but its kinetics were different. In the paste with the highest W/C, some moderate water release was recorded from the beginning. In the other two pastes, SAP 2 retained its stored liquid during the dormant period, i.e., up to the percolation threshold. Intense desorption then set in and continued throughout the acceleration period. These findings explain the pronouncedly higher efficiency of SAP 2 as internal curing admixture as compared to SAP 1.

36 MATERIALS SCIENCE↗

Interactions between fluoride ions and cement paste containing superplasticizer

Fluoride compounds are used as fluxes in the low-temperature calcination of cement. Elution of fluoride ions after calcination decreases the fluidity of cement paste containing superplasticizers, but the mechanism of fluidity decrease is unclear. Authors investigated the effects of fluoride on cement pastes containing superplasticizers and the fluidity decrease mechanism. KF addition to cement paste containing a polycarboxylate- or naphthalenesulfonate-based superplasticizer increased the yield stress, the amount of adsorbed superplasticizer, and the solid-phase specific surface area. KF addition increased the amount of adsorbed superplasticizer for alite paste but not for Ca{sub 3}Al{sub 2}O{sub 6}-CaSO{sub 4} paste. Transmission electron microscopy found SiO{sub 2} fine particles after KF addition. In the absence of water, the increase in specific surface area with fluoride was larger in hydrated than in unhydrated cement. It is supposed that the fluidity decrease results from the preferential adsorption of superplasticizer on SiO{sub 2} particles generated by reactions between hydrated calcium silicate and fluoride ions.

36 MATERIALS SCIENCE↗

Influence of fly ash and metakaolin on the microstructure and compressive strength of magnesium potassium phosphate cement paste

The influences of fly ash and metakaolin added as substitutions (by up to 50 wt%) of magnesium potassium phosphate cement (MKPC) on the microstructures and compressive strengths of the MKPC pastes were investigated. The results indicate that the aluminosilicate fractions of both fly ash and metakaolin are involved in the acid-base reaction of MKPC system, leading to a preferential formation of irregular crystalline struvite-K incorporated with Al and Si elements and/or amorphous aluminosilicate phosphate products. Metakaolin is more reactive than fly ash in the MKPC system. For the same addition dosage, the MKPC pastes containing metakaolin exhibit higher compressive strengths than the pastes containing fly ash. This is attributed to the formation of more highly reinforced microstructures and denser interfaces between the metakaolin particle and hydration products (e.g. struvite-K) in the MKPC paste containing metakaolin. Addition of 30 wt% metakaolin increases the compressive strengths of MKPC pastes at all test ages.

36 MATERIALS SCIENCE↗

Microstructural refinement of cement paste internally cured by polyacrylamide composite hydrogel particles containing silica fume and nanosilica

Supplementary cementitious materials were incorporated into hydrogel-based internal curing agents to improve the hydration, microstructure, and ultimately strength of internally cured high-performance cement paste. Polyacrylamide composite hydrogel particles containing amorphous silica – either silica fume or nanosilica – and two different polymer network crosslink densities were synthesized and incorporated into cement paste. The presence of silica and low crosslink density increased the absorption capacity of the particles in pore solution. Micrographs of internally cured paste indicated a significant improvement in hydrogel-related void-filling ability and an increase in void size for low crosslink density particles containing silica. Compressive strength and electrical resistivity increased at later ages for paste samples containing particles with higher silica dosage. The relationship between extent of hydration, void size, and void-filling activity was found to strongly influence the paste's long-term strength and is thus an important structure-property relationship to consider when selecting hydrogels for internal curing purposes.

36 MATERIALS SCIENCE↗

The effects of the mechanical–chemical stabilization process for municipal solid waste incinerator fly ash on the chemical reactions in cement paste

Highlights: ► Milling extracted MSWI fly ash. ► Increasing specific surface area, destruction of the crystalline texture, and increasing the amount of amorphous materials. ► Increasing heavy metal stability. ► Inducing pozzolanic reactions and increasing the early and later strength of the cement paste. - Abstract: A water extraction process can remove the soluble salts present in municipal solid waste incinerator (MSWI) fly ash, which will help to increase the stability of the synthetic materials produced from the MSWI fly ash. A milling process can be used to stabilize the heavy metals found in the extracted MSWI fly ash (EA) leading to the formation of a non-hazardous material. This milled extracted MSWI fly ash (MEA) was added to an ordinary Portland cement (OPC) paste to induce pozzolanic reactions. The experimental parameters included the milling time (96 h), water to binder ratios (0.38, 0.45, and 0.55), and curing time (1, 3, 7 and 28 days). The analysis procedures included inductively coupled plasma atomic emission spectroscopy (ICP/AES), BET, mercury intrusion porosimetry (MIP), X-ray diffraction (XRD), and nuclear magnetic resonance (NMR) imaging. The results of the analyses indicate that the milling process helped to stabilize the heavy metals in the MEA, with an increase in the specific surface area of about 50 times over that of OPC. The addition of the MEA to the OPC paste decreased the amount of Ca(OH){sub 2} and led to the generation of calcium–silicate–hydrates (C–S–H) which in turned increased the amount of gel pores and middle sized pores in the cement. Furthermore, a comparison shows an increase in the early and later strength over that of OPC paste without the addition of the milled extracted ash. In other words, the milling process could stabilize the heavy metals in the MEA and had an activating effect on the MEA, allowing it to partly substitute OPC in OPC paste.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Application of Thermoporometry to Evaluate the Mesoporosity of Cement Pastes

In the context of temporary near-surface or reversible deep geological storage of intermediate-level radioactive waste (ILW), most wastes package concepts comprise an external container made of fiber reinforced concrete, receiving several primary waste packages. Self-irradiation of encapsulating and/or embedding matrices can lead to continuous production of hydrogen which, for obvious safety reasons, must be removed from the container. Previous studies have demonstrated that gas transport depends on two interdependent factors: the water saturation and the microstructural properties of the material. Most techniques used to investigate cement paste porosity require drying of the cement paste prior to the test, which can modify the material microstructure and does not permit the localization of the aqueous phase in the material with various degrees of saturations. This paper focuses on the characterization of pores in cement paste by thermoporometry. The technique, based on the thermodynamic conditions of the melting-solidification reactions of a condensate inside a porous body, provides a simple method for determining the pore size distribution in saturated cement pastes. The results obtained on cement pastes of different formulations with different types of cement are discussed in term of material microstructure and compared with those obtained by other techniques.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Physico-chemical studies of hardened cement paste structure with micro-reinforcing fibers

The results of physico-chemical studies of modified hardened cement paste with micro-reinforcing fibers are given in this article. The goal was to study the reasons of the increase of strength properties of modified hardened cement paste by the method of X-ray diffraction and electron microscopy. It is shown that the use of mineral fibers in the production of cement based material has positive effect on its properties. The study found out that the increase in the strength of the hardened cement paste with micro-reinforcing fibers is due to the increase of the rate of hydration of cement without a significant change in the phase composition in comparison with hardened cement paste without additive. The results of microstructure investigation (of control samples and samples of the reinforced hardened cement paste) have shown that introduction of mineral fibers in the amount of 0.1-2 % by weight of cement provides the structure of the homogeneous microporous material with uniform distribution of the crystalline phase provided by densely packed hydrates.

36 MATERIALS SCIENCE↗

Characterization of Laboratory Prepared Concrete Pastes Exposed to High Alkaline and High Sodium Salt Solutions

The objective of this study was to identify potential chemical degradation mechanisms for the Saltstone Disposal Unit (SDU) concretes, which over the performance life of the structures may be exposed to highly alkaline sodium salt solutions containing sulfate, hydroxide, and other potentially corrosive chemicals in salt solution and saltstone flush water, drain water, leachate and / or pore solution. The samples analyzed in this study were cement pastes prepared in the SIMCO Technologies, Inc. concrete laboratory. They were based on the paste fractions of the concretes used to construct the Saltstone Disposal Units (SDUs). SDU 1 and 4 concrete pastes were represented by the PV1 test specimens. The paste in the SDU 2, 3, 5, and 6 concrete was represented by the PV2 test specimens. SIMCO Technologies, Inc. selected the chemicals and proportions in the aggressive solutions to approximate proportions in the saltstone pore solution [2, 3, 5, and 6]. These test specimens were cured for 56 days in curing chamber before being immersed in aggressive solutions. After exposure, the samples were frozen to prevent additional chemical transport and reaction. Selected archived (retrieved from the freezer) samples were sent to the Savannah River National Laboratory (SRNL) for additional characterization using x-ray diffraction (XRD), scanning electron microscopy (SEM), and energy dispersive x-ray (EDX) spectroscopy. Characterization results are summarized in this report. In addition, a correlation between the oxide composition of the pastes and their chemical durability in the alkaline salt solutions is provided.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

A new approach to flow problems past a screen

A new method to simulate flows past a two-dimensional porous plate is proposed. The method is a simple application of a discrete vortex method which has been well established for flows past an inclined flat plate. In this method, a flow past a porous plate is described as superposition of the velocity potential of a uniform flow on that of a flow past a flat plate. The effect of porosity is replaced by that of a mass flow rate of the approaching freestream passing through the plate. Calculated flow features are compared with experiments. It is shown that the present method is effective in the simulation of the flow past a porous plate.

Inoue, O.↗

Recent Climate and Ice-Sheet Changes in West Antarctica Compared with the Past 2,000 Years

Changes in atmospheric circulation over the past five decades have enhanced the wind-driven inflow of warm ocean water onto the Antarctic continental shelf, where it melts ice shelves from below1-3. Atmospheric circulation changes have also caused rapid warming4 over the West Antarctic Ice Sheet, and contributed to declining sea-ice cover in the adjacent Amundsen-Bellingshausen seas5. It is unknown whether these changes are part of a longer-term trend. Here, we use waterisotope (Delta O-18) data from an array of ice-core records to place recent West Antarctic climate changes in the context of the past two millennia. We find that the δ18O of West Antarctic precipitation has increased significantly in the past 50 years, in parallel with the trend in temperature, and was probably more elevated during the 1990s than at any other time during the past 200 years. However, Delta O-18 anomalies comparable to those of recent decades occur about 1% of the time over the past 2,000 years. General circulation model simulations suggest that recent trends in Delta O-18 and climate in West Antarctica cannot be distinguished from decadal variability that originates in the tropics. We conclude that the uncertain trajectory of tropical climate variability represents a significant source of uncertainty in projections of West Antarctic climate and ice-sheet change.

Ice-sheet↗

Application of Interparticle Spacing Model to Maximize Filler Content in Cementitious Pastes

One of the most impactful ways to reduce embodied carbon of concrete in the near term is by partially replacing Portland cement with supplementary cementitious materials and/or fillers. This article describes an approach to reduce cement content in concrete through the development of high filler, low water (HFLW) cementitious pastes. Pastes with cement content as low as 50% (% weight of fines) were designed by applying models that maximize the packing density of the granular system and that consider the characteristics of the materials to calculate interparticle spacing (IPS), thereby allowing to obtain pastes with higher solids concentration and lower water demand. Strong correlations were found between IPS, the consistency index of the Herschel-Bulkley rheological model, and cement hydration kinetic parameters of binary and ternary pastes containing a Portland limestone cement and up to two different types of ground limestone. The approach showed to be feasible for the design of HFLW concrete paste fraction.

Antunes da Silva, Denise↗

Investigation of the Interactions Between Low-Temperature Ag Paste Components and SiO2/Poly-Si(n) Contacts and the Impact on Contact Properties

Reducing poly-Si thickness to minimize parasitic absorption on a light-receiving side of a TOPCon solar cell without suffering voltage losses after metallization is a challenge in optimizing TOPCon performance. As an alternative to fire-through pastes, we investigate low-temperature Ag paste to SiO2/poly-Si passivating contacts through fabrication of electrical test structures to characterize the passivation quality and electrical transport across the metallized interface. With current paste chemistries, we find that solvent wetting of the poly-Si surface before evaporation and non-volatile binder resin adhesion to the surface after curing are major impediments which prevent Ag contact formation. However, low- resistance poly-Si/Ag interfaces formed with physical vapour deposition similarly degrade after annealing, indicating contacting issues related to the Ag content even in the absence of the organic paste components.

low temperature Ag paste↗

The mechanism of cesium immobilization in densified silica-fume blended cement pastes

The role of silica-fume agglomerates, found in densified silica-fume (DSF) pastes, in the immobilization mechanism of Cs ions was studied. Samples of cementitious pastes containing two different forms of silica fume - DSF and raw silica fume (RSF) - were prepared. Leaching experiments showed that both additives reduced the leachability of the metal ion, but the effect of the DSF paste was much stronger. Scanning Electron Microscopy, together with Differential Thermal Analysis, proved that no agglomerated particles were present in the RSF pastes and that the extent of pozzolanic reactivity was higher. We therefore believe that unreacted silica within the DSF agglomerates adsorbs Cs ions and consequently increases their immobilization. Furthermore, this work suggests that during the pozzolanic reaction, a hydrated rim develops around the agglomerate that acts as an additional diffusion barrier for the Cs ions, resulting in an increased efficiency of Cs immobilization.

36 MATERIALS SCIENCE↗

On the mechanism of polypropylene fibres in preventing fire spalling in self-compacting and high-performance cement paste

With the increasing application of self-compacting concrete (SCC) in construction and infrastructure, the fire spalling behavior of SCC has been attracting due attention. In high performance concrete (HPC), addition of polypropylene fibers (PP fibers) is widely used as an effective method to prevent explosive spalling. Hence, it would be useful to investigate whether the PP fibers are also efficient in SCC to avoid explosive spalling. However, no universal agreement exists concerning the fundamental mechanism of reducing the spalling risk by adding PP fiber. For SCC, the reduction of flowability should be considered when adding a significant amount of fibres. In this investigation, both the micro-level and macro-level properties of pastes with different fiber contents were studied in order to investigate the role of PP fiber at elevated temperature in self-compacting cement paste samples. The micro properties were studied by backscattering electron microscopy (BSE) and mercury intrusion porosimetry (MIP) tests. The modification of the pore structure at elevated temperature was investigated as well as the morphology of the PP fibers. Some macro properties were measured, such as the gas permeability of self-compacting cement paste after heating at different temperatures. The factors influencing gas permeability were analyzed. It is shown that with the melting of PP fiber, no significant increase in total pore volume is obtained. However, the connectivity of isolated pores increases, leading to an increase of gas permeability. With the increase of temperature, the addition of PP fibers reduces the damage of cement pastes, as seen from the total pore volume and the threshold pore diameter changes. From this investigation, it is concluded that the connectivity of pores as well as the creation of micro cracks are the major factors which determine the gas permeability after exposure to high temperatures. Furthermore, the connectivity of the pores acts as a dominant factor for temperatures below 300 deg. C. For higher temperatures micro cracks are becoming the major factor which influences the gas permeability.

36 MATERIALS SCIENCE↗

Influence of spraying on the early hydration of accelerated cement pastes

In practice, most of the studies about the interaction between cement and accelerators is performed with hand-mixed pastes. However, in many applications mixing occurs through spraying, which may affect accelerators reactivity and the microstructure of the hardened paste. The objective of this study is to analyze how the mixing process influences the early hydration of accelerated cement pastes. Isothermal calorimetry, X-ray diffraction, thermogravimetry and SEM imaging were performed on cement pastes produced by hand-mixing and by spraying, using equivalent doses of an alkali-free and an alkaline accelerator and two types of cement. Results showed a great influence of the spraying process on the reactivity of accelerators and on the morphology of the precipitated hydrates. Variations in hydration kinetics caused by the mixing method are explained and the results obtained might have a significant repercussion on how future research on the behavior of accelerated mixes will be performed.

36 MATERIALS SCIENCE↗

Micro- and nano-structural evolutions in white Portland cement/pulverized fuel ash cement pastes due to deionized-water leaching

Thin slices of white Portland cement-low calcium pulverized fuel ash (pfa) blended cement pastes containing 30 or 50% pfa were leached progressively in de-ionized water. The paste with 50% pfa was aged 13 years prior to leaching and those with 30% pfa were aged 1 and 13 years. Pastes were leached for up to 75 days and were characterized using thermal analysis, X-ray diffraction, analytical scanning and transmission electron microscopy, and solid-state nuclear magnetic resonance spectroscopy. Leaching affected the pastes in the following sequence: (i) crystals of Ca(OH){sub 2} large enough to be resolved by backscattered electron imaging were removed completely prior to any effect on C-A-S-H; (ii) the Ca/Si ratio of C-A-S-H reduced from ≈ 1.4 to ≈ 1.0 whilst the aluminosilicate structure was unaffected; (iii) further reduction in the Ca/Si ratio of C-A-S-H was accompanied by lengthening of the aluminosilicate chains; (iv) the Ca/Si ratio of C-A-S-H reduced ultimately to ≈ 0.6.

36 MATERIALS SCIENCE↗