Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “P CODES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

Verification and Validation of the PLTEMP/ANL Code for Thermal-Hydraulic Analysis of Experimental and Test Reactors

The document compiles in a single volume several verification and validation works done for the PLTEMP/ANL code during the years of its development and improvement. Some works that are available in the open literature are simply referenced at the outset, and are not included in the document. PLTEMP has been used in conversion safety analysis reports of several US and foreign research reactors that have been licensed and converted. A list of such reactors is given. Each chapter of the document deals with the verification or validation of a specific model. The model verification is usually done by comparing the code with hand calculation, Microsoft spreadsheet calculation, or Mathematica calculation. The model validation is done by comparing the code with experimental data or a more validated code like the RELAP5 code.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Neutron Yield Study of Direct-Drive, Low-Adiabat Cryogenic D2 Implosions on OMEGA Laser System

Neutron yields of direct-drive, low-adiabat (alpha ~~ 2 to 3) cryogenic D2 target implosions on the OMEGA laser system [T. R. Boehly et al., Opt. Commun. 133, 495 (1997)] have been systematically investigated using the two-dimensional (2D) radiation hydrodynamics code DRACO [P. B. Radha et al., Phys. Plasmas 12, 056307 (2005)]. Low-mode (ell <- 12) perturbations, including initial target offset, ice-layer roughness, and laser-beam power imbalance, were found to be the primary source of yield reduction for thin-shell (5 um), low-alpha, cryogenic targets. The 2D simulations of thin-shell implosions track experimental measurements for different target conditions and peak laser intensities ranging from 2.5 x 10^14–6 x 10^14 W/cm^2. Simulations indicate that the fusion yield is sensitive to the relative phases between the target offset and the ice-layer perturbations. The results provide a reasonable good guide to understanding the yield degradation in direct-drive, low-adiabat, cryogenic, thin-shell-target implosions. Thick-shell (10 um) implosions generally give lower yield over clean than low-ell-mode DRACO simulation predictions. Simulations including the effect of laser-beam nonuniformities indicate that high-ell-mode perturbations caused by laser imprinting further degrade the neutron yield of thick-shell implosions. To study ICF compression physics, these results suggest a target specification with a <-30 um offset and ice-roughness of sigma_rms < 3 um are required.

Hu, S X↗

User Manual for the PROTEUS Mesh Tools

This report describes the various mesh tools that are provided with the PROTEUS code giving both descriptions of the input and output. In many cases the examples are provided with a regression test of the mesh tools. The most important mesh tools for any user to consider using are the MT_MeshToMesh.x and the MT_RadialLattice.x codes. The former allows the conversion between most mesh types handled by PROTEUS while the second allows the merging of multiple (assembly) meshes into a radial structured grid. Note that the mesh generation process is recursive in nature and that each input specific for a given mesh tool (such as .axial or .merge) can be used as “mesh” input for any of the mesh tools discussed in this manual.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Frame sync acquisition for biorthogonally coded data

The paper analyzes the optimum frame-synchronization problem for biorthogonally coded data received over the additive white Gaussian noise (AWGN) channel and decoded prior to sync acquisition. In deriving the optimum frame-sync algorithm, the discussion is restricted to the case in which each frame contains F complete code words, including a frame-sync prefix of P complete code words. The k-bit source words and k-bit decoded words are regarded as super symbols from an alphabet of binary k-tuples. The biorthogonal encoder, the AWGN channel, and the decoder are lumped into a super symbol channel whose characteristics determine the form of the optimum frame-sync decision rule. A union-bound approach is used to provide a quantitative measure of the probability of false synchronization for the algorithm derived.

Levitt, B. K.↗

Design study of long-life PWR using thorium cycle

Design study of long-life Pressurized Water Reactor (PWR) using thorium cycle has been performed. Thorium cycle in general has higher conversion ratio in the thermal spectrum domain than uranium cycle. Cell calculation, Burn-up and multigroup diffusion calculation was performed by PIJ-CITATION-SRAC code using libraries based on JENDL 3.2. The neutronic analysis result of infinite cell calculation shows that {sup 231}Pa better than {sup 237}Np as burnable poisons in thorium fuel system. Thorium oxide system with 8%{sup 233}U enrichment and 7.6{approx} 8%{sup 231}Pa is the most suitable fuel for small-long life PWR core because it gives reactivity swing less than 1%{Delta}k/k and longer burn up period (more than 20 year). By using this result, small long-life PWR core can be designed for long time operation with reduced excess reactivity as low as 0.53%{Delta}k/k and reduced power peaking during its operation.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Planetary Torque in 3D Isentropic Disks

Planetary migration is inherently a three-dimensional (3D) problem, because Earth-size planetary cores are deeply embedded in protoplanetary disks. Simulations of these 3D disks remain challenging due to the steep resolution requirements. Using two different hydrodynamics codes, FARGO3D and PEnGUIn, we simulate disk–planet interaction for a one to five Earth-mass planet embedded in an isentropic disk. We measure the torque on the planet and ensure that the measurements are converged both in resolution and between the two codes. We find that the torque is independent of the smoothing length of the planet’s potential ( r {sub s}), and that it has a weak dependence on the adiabatic index of the gaseous disk ( γ ). The torque values correspond to an inward migration rate qualitatively similar to previous linear calculations. We perform additional simulations with explicit radiative transfer using FARGOCA, and again find agreement between 3D simulations and existing torque formulae. We also present the flow pattern around the planets that show active flow is present within the planet’s Hill sphere, and meridional vortices are shed downstream. The vertical flow speed near the planet is faster for a smaller r {sub s} or γ , up to supersonic speeds for the smallest r {sub s} and γ in our study.

79 ASTRONOMY AND ASTROPHYSICS↗

A Prototype {sup 212}Pb Medical Dose Calibrator for Alpha Radioimmunotherapy

AREVA Med, an AREVA group subsidiary, is developing innovative cancer-fighting therapies involving the use of {sup 212}Pb for alpha radioimmunotherapy. Canberra Industries, the nuclear measurement subsidiary of AREVA, has been working with AREVA Med to develop a prototype measurement system to assay syringes containing a {sup 212}Pb solution following production by an elution system. The relative fraction of emitted radiation from the source associated directly with the {sup 212}Pb remains dynamic for approximately 6 hours after the parent is chemically purified. A significant challenge for this measurement application is that the short half-life of the parent nuclide requires assay prior to reaching equilibrium with progeny nuclides. A gross counting detector was developed to minimize system costs and meet the large dynamic range of source activities. Prior to equilibrium, a gross counting system must include the period since the {sup 212}Pb was pure to calculate the count rate attributable to the parent rather than the progeny. The dynamic state is determined by solving the set of differential equations, or Bateman equations, describing the source decay behavior while also applying the component measurement efficiencies for each nuclide. The efficiencies were initially estimated using mathematical modeling (MCNP) but were then benchmarked with source measurements. The goal accuracy of the system was required to be within 5%. Independent measurements of the source using a high resolution spectroscopic detector have shown good agreement with the prototype system results. The prototype design was driven by cost, compactness and simplicity. The detector development costs were minimized by using existing electronics and firmware with a Geiger-Mueller tube derived from Canberra's EcoGamma environmental monitoring product. The acquisition electronics, communications and interface were controlled using Python with the EcoGamma software development kit on a Raspberry Pi Linux computer mounted inside a standard project box. The results of initial calibration measurements are presented. (authors)

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

ANTARES: a new IRSN computational chain for safety analysis

Since some years, the IRSN has developed a new project to simulate accurately the interaction between neutronic and thermal hydraulic phenomena. This project called ANTARES (Advanced Neutronics and Thermal-hydraulic for the Analysis of Reactor Safety) couples the thermal hydraulic code CATHARE-3 with the 3D neutronic nodal code PARCS. The purpose of this project is to take the advantage of the complementary of these 2 codes, by the knowledge of the 3D core power distribution in CATHARE-3 (computed by PARCS) and improving the thermal hydraulic boundaries conditions in PARCS. In this way, the IRSN diversifies and enlarges its available tools to perform safety analysis with improved accuracy. The current technique usually adopted in France for the safety demonstrations for Reactivity Insertion Accident (RIA) is the so-called 'conservative' approach, which consists of reducing all the feedback (Doppler and moderator effects) and in modifying some physical quantities in such a way to increase a power peak. For this reason, these facilities ('penalties') have been implemented in ANTARES. In this paper we will give two examples of accidental transients that can be simulated with ANTARES: a Main Steam Line Break (MSLB) and an inadvertent boron dilution event. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

ABSTRACTION OF INFORMATION FROM 2- AND 3-DIMENSIONAL PORFLOW MODELS INTO A 1-D GOLDSIM MODEL - 11404

The Savannah River National Laboratory has developed a 'hybrid' approach to Performance Assessment modeling which has been used for a number of Performance Assessments. This hybrid approach uses a multi-dimensional modeling platform (PorFlow) to develop deterministic flow fields and perform contaminant transport. The GoldSim modeling platform is used to develop the Sensitivity and Uncertainty analyses. Because these codes are performing complementary tasks, it is incumbent upon them that for the deterministic cases they produce very similar results. This paper discusses two very different waste forms, one with no engineered barriers and one with engineered barriers, each of which present different challenges to the abstraction of data. The hybrid approach to Performance Assessment modeling used at the SRNL uses a 2-D unsaturated zone (UZ) and a 3-D saturated zone (SZ) model in the PorFlow modeling platform. The UZ model consists of the waste zone and the unsaturated zoned between the waste zone and the water table. The SZ model consists of source cells beneath the waste form to the points of interest. Both models contain 'buffer' cells so that modeling domain boundaries do not adversely affect the calculation. The information pipeline between the two models is the contaminant flux. The domain contaminant flux, typically in units of moles (or Curies) per year from the UZ model is used as a boundary condition for the source cells in the SZ. The GoldSim modeling component of the hybrid approach is an integrated UZ-SZ model. The model is a 1-D representation of the SZ, typically 1-D in the UZ, but as discussed below, depending on the waste form being analyzed may contain pseudo-2-D elements. A waste form at the Savannah River Site (SRS) which has no engineered barriers is commonly referred to as a slit trench. A slit trench, as its name implies, is an unlined trench, typically 6 m deep, 6 m wide, and 200 m long. Low level waste consisting of soil, debris, rubble, wood, etc. is disposed within the trench which is then covered with soil and a cap. The filled trench resembles the surrounding soil, albeit with a higher porosity. As a result, the flow field through the trench is essentially 1-dimensional. This dimensionality makes the abstraction of information from this waste form fairly simple. Engineered waste forms present challenges not seen in the slit trench because of their higher dimensionality. Flow fields must conform to the barriers and are therefore subject to changes in direction. This paper will examine one case and show how this multidimensional flow field can be abstracted into a 1-dimensional flow field while retaining characteristics important to the transport of radioactive contaminants. One complication not addressed by the two preceding examples is that of multiple sources. This presents quite a challenge to the benchmarking exercise, but a fairly robust method has been developed to deal with it. While the PorFlow analyses can treat all sources as independent in space, this is not possible with a 1-D model. This problem has been addressed by constructing multiple 1-D models of the waste forms and using plume overlaps at the assessment points to address the multiple sources which can contribute to a distinct assessment point.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Non-local equilibrium two-phase flow model with phase change in porous media and its application to reflooding of a severely damaged reactor core

A generalized non local-equilibrium, three-equation model was developed for the macroscopic description of two-phase flow heat and mass transfer in porous media subjected to phase change. Six pore-scale closure problems were proposed to determine all the effective transport coefficients for representative unit cells. An improved model is presented in this paper with the perspective of application to intense boiling phenomena. The objective of this paper is to present application of this model to the simulation of reflooding of severely damaged nuclear reactor cores. In case of accident at a nuclear power plant, water sources may not be available for a long period of time and the core heats up due to the residual power. Any attempt to inject water during core degradation can lead to quenching and further fragmentation of the core material. The fragmentation of fuel rods and melting of reactor core materials may result in the formation of a {sup d}ebris bed{sup .} The typical particle size in a debris bed might reach few millimeters (characteristic length-scale: 1 to 5 mm), which corresponds to a high permeability porous medium. The proposed two-phase flow model is implemented in the ICARECATHARE code, developed by IRSN to study severe accident scenarios in pressurized water reactors. Currently, the French IRSN has set up two experimental facilities to study debris bed reflooding, PEARL and PRELUDE, with the objective to validate safety models. The PRELUDE program studies the complex two phase flow of water and steam in a porous medium (diameter 180 mm, height 200 mm), initially heated to a high temperature (400 deg. C or 700 deg. C). The series of PRELUDE experiments achieved in 2010 constitute a significant complement to the database of high temperature bottom reflood experimental data. They provide relevant data to understand the progression of the quench front and the intensity of heat transfer. Modeling accurately these experiments required improvements to the reflooding model, especially in terms of the existence of various saturation regimes. The improved two-phase flow model shows a good agreement with PRELUDE experimental results.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Application of Generic Disposal System Models

This report describes specific GDSA activities in fiscal year 2015 (FY2015) toward the development of the enhanced disposal system modeling and analysis capability for geologic disposal of nuclear waste. The GDSA framework employs the PFLOTRAN thermal-hydrologic-chemical multi-physics code (Hammond et al., 2011) and the Dakota uncertainty sampling and propagation code (Adams et al., 2013). Each code is designed for massively-parallel processing in a high-performance computing (HPC) environment. Multi-physics representations in PFLOTRAN are used to simulate various coupled processes including heat flow, fluid flow, waste dissolution, radionuclide release, radionuclide decay and ingrowth, precipitation and dissolution of secondary phases, and radionuclide transport through the engineered barriers and natural geologic barriers to a well location in an overlying or underlying aquifer. Dakota is used to generate sets of representative realizations and to analyze parameter sensitivity.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

FRAMES-2.0 Software System: Frames 2.0 Pest Integration (F2PEST)

The implementation of the FRAMES 2.0 F2PEST module is described, including requirements, design, and specifications of the software. This module integrates the PEST parameter estimation software within the FRAMES 2.0 environmental modeling framework. A test case is presented.

97 MATHEMATICS AND COMPUTING↗

Optimized design of reactor cores for continuous operation of Belgian nuclear power plants

Two Belgian nuclear power plants, owned and operated by Electrabel, were initially planned to be phased out in 2015, reaching their maximum life time of operation by the initial design. The fuel management of those two units has been subsequently designed by Tractebel to make the best use of the energy in the fuel assemblies either in the core or in the storage pool and to minimize the size of the fresh reloads in the terminating cycles. However, for ensuring energy security in Belgium, the Government decided in the same year to extend the life time of operation of the two units for 10 years, which raised the need to resume their continuous operation, in the opposite direction of the core contents and with a significant break in the usual sequence of cycle reloads. All this required adaptation of the tools and process for optimized reactor core design, in order to ensure the continuous and flexible operation of those units. The Tractebel LWRWIMS-PANTHER (LWP) core physics package is based on the 3-dimensional (3D) neutronic code PANTHER and the lattice code LWRWIMS for the generation of the assembly nuclear data. Both have been qualified by Tractebel for the Belgian Units to perform a complete range of PWR reactor calculations for fuel management design safety parameters assessment, transient analysis and operational support. In-core fuel management involves calculating core reactivity, power distribution and isotopic inventory for subsequent fuel cycles of a nuclear power plant in order to maintain adequate safety margins and operating lifetime for each core loading. This paper presents Tractebel's improved core design tools and process, the approach to optimize the reactor core design, and the applications to the 2 successive but opposite design requirements.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Importance of 3-D S{sub N} depletion in non-proliferation using BSOLVE

We present a single Pressurized Water Reactor (PWR) 3-D fuel rod design for depletion analysis using BSOLVE, our newly developed Runge-Kutta-Fehlberg based depletion code. BSOLVE is coupled with the deterministic 3-D S{sub N} particle transport code, PENTRAN, applied here with a 4-neutron energy group comparison to Continuous Energy (C/E) SERPENT2 Monte Carlo results. Differences are expected, as PENTRAN+BSOLVE retains full (multi-group) energy information for reactions, nuclide specific fission contributions, and energy dependent fission yields, using the latest available ENDF-BVIII data, important to retain accurate burned fuel inventories; SERPENT2 collapses burnup reactions to a single energy value. For depletion times up to ∼ 700 days and typical PWR power densities, relative differences between multigroup 3-D S{sub N} with full energy data and Monte Carlo one group burnup for trans-uranium nuclide concentrations and fission products are up to ∼20%. System eigenvalues are consistent, but with differences early and late in the cycle attributed to multigroup vs. C/E Monte Carlo cross sections. This work highlights the importance of low variance transport driven burnup for non-proliferation concerns, since plutonium quality varies significantly along axial lengths, and is more challenging to converge using Monte Carlo; details of depletion steps with spatial/zone dependent plutonium quality are provided. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗