Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “OSCILLATING CYLINDER”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

An experimental study of free surface deformation in oscillatory thermocapillary flow

Free surface deformation of a test fluid induced by steady and oscillatory thermocapillary flow in a small cylindrical container (diameter = 4.8 mm) is studied experimentally. The fluid (2 Cs oil) is heated by a cylindrical wire (diameter = 0.48 mm) placed along the centerline of the cylinder. The relative displacement and oscillation frequency of free surface are measured in a radial cross-section for various applied temperature differences. It is found that the amplitude of the free surface height oscillations is large near the heater and the cold wall and relatively small in the middle part. The frequency of the free surface oscillations is same as the frequency of the temperature oscillations. Based on these data, the free surface motion during oscillations is delineated.

Lin, Jianlian↗
NASA NTRS1988

Comparative study of cross-field and field-aligned electron beams in active experiments

Beam-plasma interactions associated with the cross-field and field-aligned injection of electron beams from spacecraft were investigated using a two-dimensional (three velocity component) electrostatic particle simulations. It is shown that the beam properties and plasma response can be characterized well by the ratio between the stagnation time and the plasma response time, which depends on the ratio of the ambient plasma density to the beam density, the beam width, the beam energy, and the spacecraft length. It was found that the beams injected across the field lines tend to lose their coherence after about one or two gyrations due to space-charge oscillations induced by the beam, irrespective of the spacecraft charging. These oscillations scatter the beam electrons into a hollow cylinder of a radius equal to a beam electron gyroradius and thickness of the order of two beam Debye lengths. Parallel injected beams are subjected to similar oscillations, which cause the beam to expand to fill a solid cylinder of a comparable thickness.

Winglee, R. M.↗
DOE OSTI2021

Specular-reflection contributions to static and dynamic radiation forces on circular cylinders

Interest in the response of highly reflecting objects in water to modulated acoustical radiation forces makes it appropriate to consider contributions to such forces from perfectly reflecting objects to provide insight into radiation forces. The acoustic illumination can have wavelengths much smaller than the object's size, and objects of interest may have complicated shapes. Here, the specular contribution to the oscillating radiation force on an infinite circular cylinder at normal incidence is considered for double-sideband-suppressed carrier-modulated acoustic illumination. The oscillatory magnitude of the specular force decreases monotonically with increasing modulation frequency, and the phase of the oscillating force depends on the relative phase of the sidebands. The phase dependence on the modulation frequency can be reduced with the appropriate selection of a sideband relative-phase parameter. That is a consequence of the significance of rays that are incident on the cylinder having small impact parameters that are nearly backscattered. For one choice of a relative sideband phase, a prior partial wave series (PWS) solution is available, which supports the specular analysis when the PWS is evaluated for a rigid cylinder. The importance of specular contributions for aluminum cylinders in water is noted. A specular analysis for an analogous spherical reflector is also summarized.

Marston, Philip L. (ORCID:0000000306778537)↗
NASA NTRS1985

Computational aspects of unsteady flows

The calculation of unsteady flows and the development of numerical methods for solving unsteady boundary layer equations and their application to the flows around important configurations such as oscillating airfoils are presented. A brief review of recent work is provided with emphasis on the need for numerical methods which can overcome possible problems associated with flow reversal and separation. The zig-zag and characteristic box schemes are described in this context, and when embodied in a method which permits interaction between solutions of inviscid and viscous equations, the characteristic box scheme is shown to avoid the singularity associated with boundary layer equations and prescribed pressure gradient. Calculations were performed for a cylinder started impulsively from rest and oscillating airfoils. The results are presented and discussed. It is conlcuded that turbulence models based on an algebraic specification of eddy viscosity can be adequate, that location of translation is important to the calculation of the location of flow separation and, therefore, to the overall lift of an oscillating airfoil.

Cebeci, T.↗
DOE OSTI2025

Effects of Critical Compression Ratio on Rating Gasoline Knock Propensity

It is common practice in the automotive industry to explore the knock limits of fuels on an engine by a comparison of the knock limited spark advance (KLSA) at threshold knock intensity. However, the knock propensity of gasolines can be rated by changing one of three metrics on a variable compression ratio Cooperative Fuels Research (CFR) octane rating engine while holding the other two variables constant: knock intensity, spark timing, and critical compression ratio. The operational differences between the standard research octane number (RON) rating and modern engine operation have been explored in three parts. The first part focused on the effects of lambda and knock characterization. The second part studied the effects of spark timing. This third part explores the knock ratings of several gasolines by comparing the critical compression ratios at constant combustion phasing and knock intensity. The threshold knock intensity was based on the standard octane rating D1 pickup or by maximum amplitude of pressure oscillations (MAPO) measured by a piezoelectric cylinder pressure transducer. Several Fuels for Advanced Combustion Engines (FACE) gasolines, primary reference fuels (PRFs), and toluene standardization fuels (TSFs) were tested on a CFR octane rating engine with advanced data acquisition equipment and a piezoelectric cylinder pressure transducer. These tests deviated from the ASTM D2699 standard octane rating procedure. For each test fuel, the CFR engine was operated at stoichiometry at a constant combustion phasing (CA50) and the compression ratio was modified until a threshold knock intensity was realized. It was found that the chemical composition of the fuels affected the relationship of critical compression ratios between the D1 knockmeter and piezoelectric pressure transducer knock intensity thresholds, as well as the measured combustion maximum pressure rise rate and spark timing setting for constant CA50. For highly aromatic fuels tested at a constant MAPO knock intensity threshold, it was found that the maximum pressure rise rate was two to three times higher than that of highly paraffinic fuels with similar RON and the spark advance was several crank angle degrees less for constant combustion phasing.

Kolodziej, Christopher P↗
NASA NTRS1985

Instability of time-periodic flows

The instabilities of some spatially and/or time-periodic flows are discussed, in particular, flows with curved streamlines which can support Taylor-Gortler vortices are described in detail. The simplest flow where this type of instability can occur is that due to the torsional oscillations of an infinitely long circular cylinder. For more complicated spatially varying time-periodic flows, a similar type of instability can occur and is spatially localized near the most unstable positions. When nonlinear effects are considered it is found that the instability modifies the steady streaming boundary layer induced by the oscillatory motion. It is shown that a rapidly rotating cylinder in a uniform flow is susceptible to a related type of instability; the appropriate stability equations are shown to be identical to those which govern the instability of a boussinesq fluid of Prandtl number unity heated time periodically from below.

Hall, P.↗
NASA NTRS1987

Instability of time-periodic flows

The instabilities of some spatially and/or time-periodic flows are discussed, in particular, flows with curved streamlines which can support Taylor-Gortler vortices are described in detail. The simplest flow where this type of instability can occur is that due to the torsional oscillations of an infinitely long circular cylinder. For more complicated spatially varying time-periodic flows, a similar type of instability can occur and is spatially localized near the most unstable positions. When nonlinear effects are considered it is found that the instability modifies the steady streaming boundary layer induced by the oscillatory motion. It is shown that a rapidly rotating cylinder in a uniform flow is susceptible to a related type of instability; the appropriate stability equations are shown to be identical to those which govern the instability of a Boussinesq fluid of Prandtl number unity heated time periodically from below.

Hall, Philip↗
DOE OSTI2021

Surface prediction and measurement for modulated tool path (MTP) turning

Here, this paper describes a time-domain simulation for predicting surface finish in modulated tool path (MTP) turning, which uses sinusoidal axis motions in the feed direction to produce discontinuous chips for ductile workpiece materials. The simulation includes: the low frequency and low amplitude tool oscillation in the feed direction; the time-varying chip thickness, cutting force, and tool displacement; and the plastic side flow effect used to calibrate the effective tool nose radius. Comparisons between predicted and measured surface profiles are presented for turning a 6061-T6 aluminum cylinder as a function of the MTP oscillation frequency and amplitude with discontinuous chip formation.

42 ENGINEERING↗
NASA NTRS1984

Effect of an oscillating flow direction on leading edge heat transfer

An experimental investigation was conducted to examine the effect of a periodic variation in the angle of attack on heat transfer at the leading edge of a gas turbine blade. A circular cylinder was used as a large-scale model of the leading edge region. The cylinder was placed in a wind tunnel and was oscillated rotationally about its axis. The incident flow Reynolds number and the Strouhal number of oscillation were chosen to model an actual turbine condition. Incident turbulence levels up to 4.9 percent were produced by grids placed upstream of the cylinder. The transfer rate was measured using a mass transfer technique and heat transfer rates inferred from the results. A direct comparison of the unsteady and steady results indicate that the effect is dependent on the Strouhal number, turbulence level, and the turbulence length scale, but that the largest observed effect was only a 10 percent augmentation at the nominal stagnation position.

Marziale, M. L.↗
NASA NTRS1989

Dynamical behavior of surface tension on rotating fluids in low and microgravity environments

Consideration is given to the time-dependent evolutions of the free surface profile (bubble shapes) of a cylindrical container, partially filled with a Newtonian fluid of constant density, rotating about its axis of symmetry in low and microgravity environments. The dynamics of the bubble shapes are calculated for four cases: linear time-dependent functions of spin-up and spin-down in low and microgravity, linear time-dependent functions of increasing and decreasing gravity at high and low rotating cylinder speeds, time-dependent step functions of spin-up and spin-down in low gravity, and sinusoidal function oscillation of the gravity environment in high and low rotating cylinder speeds. It is shown that the computer algorithms developed by Hung et al. (1988) may be used to simulate the profile of time-dependent bubble shapes under variations of centrifugal, capillary, and gravity forces.

Hung, R. J.↗
NASA NTRS1977

Accretion of rotating fluids by barytropes - Numerical results for white-dwarf models

Numerical sequences of rotating axisymmetric nonmagnetic equilibrium models are constructed which represent the evolution of a barytropic star as it accretes material from a rotating medium. Two accretion geometries are considered - one approximating accretion from a rotating cloud and the other, accretion from a Keplerian disk. It is assumed that some process, such as Ekman spin-up or nonequilibrium oscillations, maintains nearly constant angular velocity along cylinders about the rotation axis. Transport of angular momentum in the cylindrically radial direction by viscosity is included. Fluid instabilities and other physical processes leading to enhancement of this transport are discussed. Particular application is made to zero-temperature white-dwarf models, using the degenerate electron equation of state. An initially nonrotating 0.566-solar-mass white dwarf is followed during the accretion of more than one solar mass of material. Applications to degenerate stellar cores, to mass-transfer binary systems containing white dwarfs, such as novae and dwarf novae, to Type I supernovae, and to galactic X-ray sources are considered.

Durisen, R. H.↗
NASA NTRS1990

Dynamics of surface tension in microgravity environment

Time-dependent evolutions of the profile of free surface (bubble shapes) for a cylindrical container partially filled with a Newtonian fluid of constant density, rotating about its axis of symmetry, in low and microgravity environments, have been studied. Numerical computations of the dynamics of bubble shapes have been carried out (1) linear time-dependent functions of spin-up and spin-down in low and microgravity environments, (2) linear time-dependent functions of increasing and decreasing gravity environment at high and low rotating cylinder speeds, (3) time-dependent step functions of spin-up and spin-down in a low-gravity environment, and (4) sinusoidal function oscillation of the gravity environment at high and low rotating cylinder speeds.

Hung, R. J.↗
NASA NTRS1982

Solution of the two-dimensional Euler equations with generalized coordinate transformation using flux vector splitting

An implicit finite difference code using flux vector splitting has been developed for solving the two-dimensional inviscid gas dynamics equations. The method is spatially second-order acurate, fully conservative, and uses body-conforming generalized coordinates for treating complex geometries. Numerical results have been obtained for transonic flow over a circular cylinder and airfoils. Steady results for a half cylinder (top and bottom symmetry-imposed) range from critical flow to a strong shock case with rotationally induced flow separation. Full cylinder solutions at freestream Mach number values of 0.5, however, show unsteady oscillation. A perturbation form of the method has also been developed and used to compute both fore and aft inviscid flow separation about a cylinder for a nonuniform incoming stream.

Buning, P. G.↗
NASA NTRS1988

An upwind differencing scheme for the time-accurate incompressible Navier-Stokes equations

The two-dimensional incompressible Navier-Stokes equations are solved in a time-accurate manner in using the method of pseudocompressibility. Using this method, subiterations in pseudotime are required to satisfy the continuity equation at each time step. An upwind differencing scheme based on flux-difference splitting is used to compute the convective terms. The upwind differencing is biased based on the sign of the local eigenvalue of the Jacobian matrix. Third-order or fifth-order spatial accuracy is maintained throughout the interior grid points. The equations are solved using an implicit line-relaxation scheme. This solution scheme is stable and is capable of running at large time steps in pseudotime, leading to fast convergence for each physical time step. A variety of computed results are presented to validate the present scheme. Results for the flow over an oscillating plate are compared with the exact analytic solution, good agreement is seen. Excellent comparison is obtained between the computed solution and the analytical results for inviscid channel flow with an oscillating back pressure. Flow solutions over a circular cylinder with vortex shedding are also presented. Finally, the flow past an airfoil at -90 deg angle-of-attack is also computed.

Rogers, Stuart E.↗
NASA NTRS1991

Comparison of SMAC, PISO, and iterative time-advancing schemes for unsteady flows

Calculations of unsteady flows using a simplified marker and cell (SMAC), a pressure implicit splitting of operators (PSIO), and an iterative time advancing scheme (ITA) are presented. A partial differential equation for incremental pressure is used in each time advancing scheme. Example flows considered are a polar cavity flow starting from rest and self-sustained oscillating flows over a circular and a square cylinder. For a large time step size, the SMAC and ITA are more strongly convergent and yield more accurate results than PSIO. The SMAC is the most efficient computationally. For a small time step size, the three time advancing schemes yield equally accurate Strouhal numbers. The capability of each time advancing scheme to accurately resolve unsteady flows is attributed to the use of new pressure correction algorithm that can strongly enforce the conservation of mass. The numerical results show that the low frequency of the vortex shedding is caused by the growth time of each vortex shed into the wake region.

Kim, Sang-Wook↗
NASA NTRS1992

Comparison of the SMAC, PISO, and iterative time-advancing schemes for unsteady flows

Calculations of unsteady flows using a simplified marker and cell (SMAC), a pressure implicit splitting of operators (PISO), and an iterative time advancing scheme (ITA) are presented. A partial differential equation for incremental pressure is used in each time advancing scheme. Example flows considered are a polar cavity flow starting from rest and self-sustained oscillating flows over a circular and a square cylinder. For a large time step size, the SMAC and ITA are more strongly convergent and yield more accurate results than PISO. The SMAC is the most efficient computationally. For a small time step size, the three time advancing schemes yield equally accurate Strouhal numbers. The capability of each time advancing scheme to accurately resolve unsteady flows is attributed to the use of new pressure correction algorithm that can strongly enforce the conservation of mass. The numerical results show that the low frequency of the vortex shedding is caused by the growth time of each vortex shed into the wake region.

Kim, S.-W.↗
DOE OSTI2022

Charged particle motion in spherically symmetric distributions of magnetic monopoles

The classical equations of motion of a charged particle in a spherically symmetric distribution of magnetic monopoles can be transformed into a system of linear equations, thereby providing a type of integrability. In the case of a single monopole, the solution was given long ago by Poincaré. In the case of a uniform distribution of monopoles, the solution can be expressed in terms of parabolic cylinder functions (essentially the eigenfunctions of an inverted harmonic oscillator). Further, this solution is relevant to recent studies of nonassociative star products, symplectic lifts of twisted Poisson structures, and fluids and plasmas of electric and magnetic charges.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗