SEARCH · Engineering Papers
Results for “Ni dissolution”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Phase instabilities in austenitic steels during particle bombardment at high and low dose rates
Disruption of phase stability by energetic particle bombardment is a major challenge in designing advanced radiation-tolerant alloys and ion beam processing of nanocomposites. Particularly, ballistic dissolution susceptibility of different solute nanocluster species in alloys is poorly understood. Here, low dose rate neutron irradiations were conducted on a Fe-Cr-Ni based austenitic steel in the BOR-60 reactor (9.4 × 10 -7 dpa/s, 318 °C) followed by accelerated dose rate ion irradiations at multiple temperatures ( 10 -3 dpa/s, 380 – 420 °C). Using atom probe tomography, the stability of radiation-enhanced Cu-rich and radiation-induced Ni-Si-Mn-rich nanoclusters was evaluated. During neutron irradiation, Cu-rich clusters nucleated with their core concentrations progressively increasing with dose, while Ni-Si-Mn-rich clusters formed and evolved into G-phase precipitates. Ion irradiations dramatically altered the nanoclusters. Cu-rich clusters were ballistically dissolved, but Ni-Si-Mn-rich clusters remained stable and coarsened with dose at 400 and 420 °C, highlighting that different nanocluster species in a single microstructure can have innately distinct ballistic dissolution susceptibilities. Solute-specific recoil rates were incorporated into the Heinig precipitate stability model, which shows that in addition to radiation-enhanced diffusion, recovery from ballistic dissolution depends on solute concentration gradient near cluster interfaces. Finally, the combined experimental-modeling study quantified the critical temperatures and damage rates where ballistic dissolution dominates for each cluster species.
Understanding the microstructural stability in a y’-strengthened Ni-Fe-Cr-Al-Ti alloy
Ni-Fe-Cr-Al-Ti alloys, with Ni levels near 50 wt.%, have the potential to develop a microstructure consisting of a face-centered cubic ? matrix with the homogeneous precipitation of fine ordered ?’ precipitates similar to traditional Ni-based superalloys with significantly greater Ni content. Scanning electron microscopy (SEM), transmission electron microscopy (TEM), atom probe tomography (APT), and CALPHAD -based thermodynamic modeling were employed to understand the phase stabilities and microstructural evolution in an age-hardenable Ni-27Fe-18Cr-1Co-1.6Al-3.75Ti-1.2Mo-0.03C (wt%) alloy. The primary heat-treatment of solution annealing at 1121°C for 4h and age-hardening treatment at 760 °C for 16h resulted in a microstructure consisting of fine ?’ precipitates in an austenitic matrix along with grain boundary carbides, consistent with thermodynamic calculations. Long-term aging at 900 °C for 250h resulted in the coarsening of ?’ along with a change in the morphology of the precipitates from spherical to a more cuboidal shape. In addition, ? phase formation was observed concomitant with the partial dissolution of the ?’ phase. The ability of computational thermodynamic models to predict microstructural characteristics is discussed.
Establishing a Design Strategy for Corrosion Resistant Structural Materials in Molten Salt Technologies
To address the gap in material design strategies for structural components in molten salt-powered technologies, the current work aimed to identify key parameters governing corrosion induced degradation of materials during exposures in molten halide salts. The applicability of the data on dissolution rates of pure metals (e.g., Cr) in a given molten salt to enable predictions of corrosion behavior of multicomponent binary and ternary Fe-based model and Ni-based commercial alloys isothermally exposed in the purified KCl-MgCl 2 in quartz capsules at 700 and 800°C was evaluated. The influence of alloy chemistry on initial dissolution rates and the consequent impact on the time-dependent corrosion induced microstructural evolution in the alloy subsurface was predicted with a coupled thermodynamic-kinetic model. Finally, the model was well able to predict the Cr depletion in all investigated alloys demonstrating the ability of the proposed approach to enable a unique design strategy for structural materials in molten salts.
Stabilized Co-Free Li-Rich Oxide Cathode Particles with An Artificial Surface Prereconstruction
Li-rich metal oxide (LXMO) cathodes have attracted intense interest for rechargeable batteries because of their high capacity above 250 mAh g –1 . However, the side effects of hybrid anion and cation redox (HACR) reactions, such as oxygen release and phase collapse that result from global oxygen migration (GOM), have prohibited the commercialization of LXMO. GOM not only destabilizes the oxygen sublattice in cycling, aggravating the well-known voltage fading, but also intensifies electrolyte decomposition and Mn dissolution, causing severe full-cell performance degradation. In this study, an artificial surface prereconstruction (ASR) for Li 1.2 Mn 0.6 Ni 0.2 O 2 particles with a molten-molybdate leaching is conducted, which creates a crystal-dense anion-redox-free LiMn 1.5 Ni 0.5 O 4 shell that completely encloses the LXMO lattice (ASR-LXMO). Differential electrochemical mass spectroscopy and soft X-ray absorption spectroscopy analyses demonstrate that GOM is shut down in cycling, which not only stabilizes HACR in ASR-LXMO, but also mitigates the electrolyte decomposition and Mn dissolution. ASR-LXMO displays greatly stabilized cycling performance as it retains 237.4 mAh g –1 with an average discharge voltage of 3.30 V after 200 cycles. More crucially, while the pristine LXMO cycling cannot survive 90 cycles in a pouch full-cell matched with a commercial graphite anode and lean (2 g A –1 h –1 ) electrolyte, ASR-LXMO shows high capacity retention of 76% after 125 cycles in full-cell cycling.
Understanding the efficacy of concentrated interstitial carbon in enhancing the pitting corrosion resistance of stainless steel
By introducing a high fraction of interstitial carbon through low temperature carburization, the pitting corrosion resistance of austenitic stainless steel can be significantly improved. Previous work attributed this to strengthening of the passive film by carbon. Here, however, we present a paradigm shift by showing that carbon actually weakens the passive film but strengthens the bonding within the alloy by forming localized (covalent) bonds with the metal atoms (Fe, Cr, Ni). Accordingly, the enhancement in pitting resistance is a result of carbon reducing the metal dissolution rate in a local pit environment by many orders of magnitude, which extremely decreases the growth stability of a pit and prevents it from transitioning into stable growth. Electronic structure calculations confirm that carbon bonds to the metal atoms and that the metal–carbon bonds are 1.4 to 2.0 times stronger than the metal–metal bonds. These results suggest a new strategy for the design of corrosion resistant alloys, namely surface engineering by infusion of concentrated interstitials that form strong bonds with the matrix atoms.
Stabilizing Cathode–Electrolyte Interphase of Nickel-Rich Single-Crystal Cathodes for Lithium-Ion Batteries
Nickel-rich single-crystal (SC) layered oxides are promising cathode candidates for next-generation lithium-ion batteries (LIBs) owing to their high energy density and structural robustness against intergranular cracking. However, their intrinsic surface reactivity with liquid electrolytes accelerates parasitic reactions at the cathode–electrolyte interphase (CEI), leading to transition-metal dissolution, gas generation, and impedance buildup. In this work, we synthesized SC-Li x Ni 0.9 Mn 0.05 Co 0.05 O 2 (NMC9055, 1 ≤ x ≤ 1.2) using a eutectic-assisted method and investigated interface stabilization strategies. A nickel-deficient Li x Ni 0.6 Mn 0.2 Co 0.2 O 2 (NMC622, 1 ≤ x ≤ 1.2) coating was applied via evaporation-based deposition to suppress CEI degradation pathways. Structural and compositional analyses confirmed uniform shell formation and preserved particle integrity. Half-cell electrochemical testing against lithium metal revealed ∼10% higher capacity retention and improved reversibility compared with pristine SC NMC9055, particularly under high-voltage operation. In conclusion, these results highlight the critical role of controlled surface chemistry in mitigating CEI instability in nickel-rich SC cathodes, offering a pathway toward enabling durable high-energy LIBs.
Improving the oxygen redox reversibility of Li-rich battery cathode materials via Coulombic repulsive interactions strategy
The oxygen redox reaction in lithium-rich layered oxide battery cathode materials generates extra capacity at high cell voltages (i.e., >4.5 V). However, the irreversible oxygen release causes transition metal (TM) dissolution, migration and cell voltage decay. To circumvent these issues, we introduce a strategy for tuning the Coulombic interactions in a model Li-rich positive electrode active material, i.e., Li 1.2 Mn 0.6 Ni 0.2 O 2 . In particular, we tune the Coulombic repulsive interactions to obtain an adaptable crystal structure that enables the reversible distortion of TMO 6 octahedron and mitigates TM dissolution and migration. Moreover, this strategy hinders the irreversible release of oxygen and other parasitic reactions (e.g., electrolyte decomposition) commonly occurring at high voltages. When tested in non-aqueous coin cell configuration, the modified Li-rich cathode material, combined with a Li metal anode, enables a stable cell discharge capacity of about 240 mAh g -1 for 120 cycles at 50 mA g -1 and a slower voltage decay compared to the unmodified Li 1.2 Mn 0.6 Ni 0.2 O 2 .
High Temperature Oxidation Behavior of Fe- and Ni-Based Alloy Foils in Water Vapor at 850 °C
Operating temperatures above 700°C are desired to improve the efficiency of power generation systems such as microturbines. Therefore, the use of creep-resistant Ni-based or Fe-based alloys, which can form protective Cr2O3 and Al2O3 scales, is required. In this paper, Fe- and Ni-based alloy foils were oxidized in air + 10 % H2O for up to 3,000 h at 850°C to identify the most promising alloys. The thickness and chemical composition of the spinel oxide formed on top of the Cr2O3 scale varied between S3100, N08120 and N06230 alloy foils. In addition, the rate of Cr and Mn loss (spinel and Cr2O3 oxidation and volatilization) or Al loss (oxidation) and the dissolution of strengthening precipitates, were found to be a function of the nature of the formed oxide (Fe or Ni-rich spinel, Cr2O3, Al2O3). Alloys N06230 and alumina-forming austenitic (AFA) steels were found to be well-suited for the applications as microturbine recuperator foil materials up to 850°C.
Dynamic stability of active sites in hydr(oxy)oxides for the oxygen evolution reaction
The poor activity and stability of electrode materials for the oxygen evolution reaction are the main bottlenecks in the water-splitting reaction for H 2 production. In this work, by studying the activity–stability trends for the oxygen evolution reaction on conductive M 1 O x H y , Fe–M 1 O x H y and Fe–M 1 M 2 O x H y hydr(oxy)oxide clusters (M 1 = Ni, Co, Fe; M 2 = Mn, Co, Cu), we show that balancing the rates of Fe dissolution and redeposition over a MO x H y host establishes dynamically stable Fe active sites. Together with tuning the Fe content of the electrolyte, the strong interaction of Fe with the MO x H y host is the key to controlling the average number of Fe active sites present at the solid/liquid interface. We suggest that the Fe–M adsorption energy can therefore serve as a reaction descriptor that unifies oxygen evolution reaction catalysis on 3 d transition-metal hydr(oxy)oxides in alkaline media. Thus, the introduction of dynamically stable active sites extends the design rules for creating active and stable interfaces.
Correlating Rate-Dependent Transition Metal Dissolution between Structure Degradation in Li-Rich Layered Oxides
Understanding the mechanism of the rate-dependent electrochemical performance degradation in cathodes is crucial to developing fast charging/discharging cathodes for Li-ion batteries. Here, in this work, taking Li-rich layered oxide Li 1.2 Ni 0.13 Co 0.13 Mn 0.54 O 2 as the model cathode, the mechanisms of performance degradation at low and high rates are comparatively investigated from two aspects, the transition metal (TM) dissolution and the structure change. Quantitative analyses combining spatial-resolved synchrotron X-ray fluorescence (XRF) imaging, synchrotron X–ray diffraction (XRD) and transmission electron microscopy (TEM) techniques reveal that low-rate cycling leads to gradient TM dissolution and severe bulk structure degradation within the individual secondary particles, and especially the latter causes lots of microcracks within secondary particles, and becomes the main reason for the fast capacity and voltage decay. In contrast, high-rate cycling leads to more TM dissolution than low-rate cycling, which concentrates at the particle surface and directly induces the more severe surface structure degradation to the electrochemically inactive rock-salt phase, eventually causing a faster capacity and voltage decay than low-rate cycling. These findings highlight the protection of the surface structure for developing fast charging/discharging cathodes for Li-ion batteries.
Catalytic open-circuit passivation by thin metal oxide films of p-Si anodes in aqueous alkaline electrolytes
Ni and NiO x -based protective thin films are shown to catalyze the oxidation of Si in the presence of O 2 in strongly alkaline KOH(aq) even in the absence of illumination. The O 2 in solution drove the open-circuit potential of the electrode to >0.4 V, which is positive of the Si passivation potential. The elevated electrochemical potential of the surface promoted formation of passive oxides on exposed Si regions of Si/Ni electrodes. Catalytic passivation of Si extended the durability of an np + -Si(100)/NiO x photoanode to >400 h while operating under simulated day/night cycles. In contrast, electrodes without a Ni(O x ) layer and/or without O 2 in solution displayed direct etching of the Si and corrosion pitting during non-illuminated, simulated nighttime episodes of day/night cycling. The O 2 -derived catalyzed passivation of Si using thin films can be generalized to multiple phases of NiO x as well as to materials other than Ni. Finally, relative to operation in aqueous alkaline conditions, decreasing the pH of the electrolyte decreased the dissolution rate of the protective oxide layer formed by the catalyzed passivation process, and consequently increased the durability of the photoanode, but yielded lower photoelectrode fill factors for water oxidation due to the relatively large kinetic overpotentials for the electrocatalyzed oxygen-evolution reaction at near-neutral pH.
Self-replenishing Ni-rich stainless-steel electrode toward oxygen evolution reaction at ampere-level
In the past few decades, tremendous attention has been devoted to enhancing the activity of oxygen evolution reaction (OER) catalysts for hydrogen production, while the cost and long-term stability of catalysts, which can play an even more important role in industrialization, have been much less emphasized. Herein, we engineered an OER electrode from abundant stainless steel (SS) via facile approaches, and the obtained electrode consists of a Ni-rich oxide surface layer with a Fe-rich metal substrate. An outstanding activity was observed with an overpotential of 316 mV at 100 mA cm −2 in 1 M KOH electrolyte. Additionally, an electrode self-replenishing concept is proposed in which a Ni-rich catalyst layer can be regenerated from a metallic substrate due to the difference in diffusion and dissolution rates of metal oxides/hydroxides, and this regeneration is validated by various characterizations. A recorded degradation rate of 0.012 was observed at 1000 mA cm −2 for 1000 h. The facile engineering of OER electrodes from SS combined with the self-replenishing catalyst can potentially address the cost, activity, and long-term stability barriers.
The interpenetration polymer network in a cement paste–waterborne epoxy system
The formation of the interpenetrating polymer network (IPN) structure within the cement-polymer system has been revealed by experiments from 2 dimensional to 3-dimensional scales. However, the microstructure design and performance prediction of IPN as a function of specific C-S-H/polymer components or ingredients' parameters e.g. water to cement ratios (w/c), polymer to cement ratios (p/c), monomer components, degree of polymerization (DP), etc. is by far not available. Here we developed a mesoscale model for IPN visualization based on the Flory-Huggins interaction theory which was applied to cement science for the first time. All the ingredients in the micro-structure were considered as soluble beads with rational sizes based on their properties obtained by molecular dynamic methods. The interaction parameters of each bead were then determined based on their element ratios and chemical backbones. The model was validated with the waterborne epoxy-cement material (WECM) in which a novel waterborne epoxy resin (WEP) was prepared and impregnated. The verification results on the 2D-3D scale show that the developed model predicts the WECM's IPN structures by rule and line concerning DP, w/c, and p/c in the mixture. The C-S-H beads were progressively scaled in size which alters the C-S-H texture to have completely different dissolution characteristics. Beads of diameter ~6 Å are more unstable and soluble which enable them to form a continuous phase in water or a composite structure with WEP. In contrast, beads with diameters larger than 10 Å have different properties with stronger nucleation effects. The results also suggest the impregnation content of WEP in cement-based material should be limited to 10% vol. to prevent the polymer IPN from decomposing into discrete clusters. The application of Flory-Huggins theory in cement-based composites demonstrates great potential in performance prediction and microstructure design.
Epitaxial heterointerfacial electron bridge synchronizes oxygen evolution activity and stability on a layered double hydroxide surface
Scalable green hydrogen production via electrocatalytic water splitting is largely restricted by the insufficient activity and stability of oxygen evolution reaction (OER) catalysts at the anode. As a class of the most active OER catalysts in alkaline electrolyzers, the application of layered double hydroxides (LDHs) remains a main challenge owing to the unstable lattice oxygen dissolution due to the dominant lattice oxygen-involving OER mechanism during long-term operation. Herein, we found that using an epitaxial hetero-interfacing nickel hydroxide (namely Ni(OH) 2 ) as an electron bridge between an active FeCo LDH and Ni foam support to form an LDH*/NFO catalyst, the electronic storage capacity around the Fermi level (-0.5 to +0.5 eV, e-D FE ) sharply increases from 0.93 per cell to 1.51 per cell. Subsequently, we demonstrate that this high e-D FE enables ceaseless and fast power injection into the kinetic process of intermediate species conversion and inhibits lattice oxygen dissolution in the active FeCo LDH. Consequently, it demonstrated a low OER overpotential of 246 mV at a current density of 100 mA cm -2 and ultrahigh stability for up to 3500 hours with an ultraslow overpotential increase rate of 9.4 × 10 -3 mV h -1 . Therefore, we developed an epitaxial hetero-interfacial electron bridging strategy to synchronize the activity and stability of available catalysts for scalable green hydrogen production via electrocatalytic water splitting.
Double-Atom Catalysts Featuring Inverse Sandwich Structure for CO 2 Reduction Reaction: A Synergetic First-Principles and Machine Learning Investigation
Electrocatalytic CO 2 reduction reactions (CO 2 RR) based on scalable and highly efficient catalysis provide an attractive strategy for reducing CO 2 emissions. Here in this work, we combined first-principles density functional theory (DFT) and machine learning (ML) to comprehensively explore the potential of double-atom catalysts (DACs) featuring an inverse sandwich structure anchored on defective graphene (gra) to catalyze CO 2 RR to generate C 1 products. We started with five homonuclear M 2 ⊥gra (M = Co, Ni, Rh, Ir, and Pt), followed by 127 heteronuclear MM'⊥gra (M = Co, Ni, Rh, Ir, and Pt, M' = Sc–Au). Stable DACs were screened by evaluating their binding energy, formation energy, and dissolution potential of metal atoms, as well as conducting first-principles molecular dynamics simulations with and without solvent water molecules. Based on DFT calculations, Rh 2 ⊥gra DAC was found to outperform the other four homonuclear DACs and the Rh-based single- and double-atom catalysts of noninverse sandwich structures. Out of the 127 heteronuclear DACs, 14 were found to be stable and have good catalytic performance. An ML approach was adopted to correlate key factors with the activity and stability of the DACs, including the sum of radii of metal and ligand atoms (d M–M' , d M–C , and d M'–C ), the sum and difference of electronegativity of two metal atoms (P M + P M' , P M – P M '), the sum and difference of first ionization energy of two metal atoms (I M + I M' , I M – I M '), the sum and difference of electron affinity of two metal atoms (A M + A M' , A M – A M '), and the number of d-electrons of the two metal atoms (Nd). The obtained ML models were further used to predict 154 potential electrocatalysts out of 784 possible DACs featuring the same inverse sandwich configuration. Overall, this work not only identified promising CO 2 RR DACs featuring the reported inverse sandwich structure but also provided insights into key atomic characteristics associated with high CO 2 RR activity.
Elucidating the reversible exsolution–dissolution behaviour of high-entropy oxides in crystalline and amorphous phases
High-entropy oxides (HEOs), as a subclass of high-entropy materials (HEMs), offer a versatile platform for catalysis by leveraging entropy-stabilized solid solutions with tunable compositions, lattice structures, and electronic properties. While exsolution–dissolution of metal species in crystalline HEOs has emerged as a promising strategy for reversible active sites regeneration, the dynamic behaviour of HEOs possessing amorphous nature remains under-explored, particularly the difference with crystalline counterparts. In this work, we systematically investigate the architecture-dependent exsolution–dissolution behavior of HEOs by comparing a crystalline-phase HEO (c-HEO) and an amorphous-phase HEO (a-HEO), both comprising Ni, Mg, Cu, Zn, and Co as principal metal elements. Using a combination of in situ variable-temperature X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), electron microscopy, and in situ CO diffuse reflectance infrared Fourier transform spectroscopy (CO-DRIFTS), the structural evolution of the two HEO phases under redox conditions was elucidated. Both materials exhibit reversible exsolution of metallic species or alloys in reducing environments, followed by re-incorporation into the host lattice upon oxidation. Remarkably, the a-HEO demonstrates more facile and dynamic self-healing behavior, with alloy exsolution and dissolution occurring under milder conditions because of its enhanced reducibility and structural disorder. This study provides critical insights into the design of next-generation regenerable catalysts based on amorphous HEOs, highlighting the role of phase structure in governing reversible metal-site formation dynamics and catalytic performance.
The Dissolution of Cr and Fe at 850°C in FLiNaK and FLiBe
Understanding the solubility of common alloying elements, such as Cr and Fe, in fluoride salts, can provide valuable insights into the degradation process of alloys in these salts and assist in modeling the attack observed in static and flowing conditions. Previous isothermal dissolution experiments at 550°-750°C in FLiNaK showed little effect of time or temperature on the amount of dissolution, which was not expected. Therefore, the purpose of this milestone was to extend those observations to 850°C where Ni-based alloys have been developed with 100+X better creep strength than the historic Hastelloy N alloy developed for molten salt reactors more than 50 years ago. Exposures were conducted in the same commercial FLiNaK and FLiBe salts used in the lower temperature exposures.