SEARCH · Engineering Papers

Results for “MgO”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

All sources NASA NTRS DOE OSTI

DOE OSTI2024

Tunneling magnetoresistance in MgO tunnel junctions with Fe-based leads in empirically corrected density functional theory

The minority-spin Fe/MgO interface states are at the Fermi level in density functional theory (DFT), but experimental evidence and GW calculations place them slightly higher in energy. This small shift can strongly influence tunneling magnetoresistance (TMR) in junctions with a thin MgO barrier and its dependence on the concentration of Co in the electrodes. Here, in this study, an empirical potential correction to DFT is introduced to shift the interface states up to match the tunnel spectroscopy data. With this shift, TMR in Fe/MgO/Fe junctions exceeds 800% and 3000% at 3 and 4 monolayers (ML) of MgO, respectively. We further consider the effect of alloying of the Fe electrodes with up to 30% Co or 10% V, treating them in the coherent potential approximation (CPA). Alloying with Co broadens the interface states and brings a large incoherent minority-spin spectral weight to the Fermi level. Alloying with V brings the minority-spin resonant states close to the Fermi level. However, in both cases the minority-spin spectral weight at the Fermi level resides primarily at the periphery of the Brillouin zone, which is favorable for spin filtering. Using convolutions of k II -resolved barrier densities of states calculated in CPA, it is found that TMR is strongly reduced by alloying with Co or V but still remains above 500% at 4 ML of MgO up to 30% of Co or 5% V. At 5 ML, the TMR increases above 1000% in all systems considered. However, while TMR declines sharply with increasing bias up to 0.2 eV in the tunnel junctions with pure Fe leads, it remains almost constant up to 0.5 eV if leads are alloyed with Co.

74 ATOMIC AND MOLECULAR PHYSICS↗

DOE OSTI2025

Low viscosity of solid MgO at high pressures and strain rates measured using the laser-driven Richtmyer-Meshkov instability

Solids are often assumed to behave as viscous fluids under high-strain rates. This behavior has been studied experimentally in metals but largely unexplored in brittle ceramic materials. Here, in this study, we present a technique for measuring the viscosity of MgO using time-resolved velocimetry to track the growth rate of a perturbation caused by the Richtmyer-Meshkov instability at the OMEGA EP laser facility. To interpret the results, we use an in-house Eulerian hydrocode to simulate our experiments and model the plastic deformation of solid MgO as a viscous fluid. Results indicate that MgO has a surprisingly low upper bound to its effective viscosity of ∼10 2 ⁢ Pa s at 175 ± 15⁢ GPa, ∼3500⁢K, and 10 6 −10 7 s −1 strain rate.

Perez, Tyler M. [Johns Hopkins Univ., Baltimore, M↗

DOE OSTI2024

B1-B2 transition in shock-compressed MgO

Magnesium oxide (MgO) is a major component of the Earth’s mantle and is expected to play a similar role in the mantles of large rocky exoplanets. At extreme pressures, MgO transitions from the NaCl B1 crystal structure to a CsCl B2 structure, which may have implications for exoplanetary deep mantle dynamics. In this study, we constrain the phase diagram of MgO with laser-compression along the shock Hugoniot, with simultaneous measurements of crystal structure, density, pressure, and temperature. We identify the B1 to B2 phase transition between 397 and 425 gigapascal (around 9700 kelvin), in agreement with recent theory that accounts for phonon anharmonicity. From 425 to 493 gigapascal, we observe a mixed-phase region of B1 and B2 coexistence. The transformation follows the Watanabe-Tokonami-Morimoto mechanism. Our data are consistent with B2-liquid coexistence above 500 gigapascal and complete melting at 634 gigapascal. This study bridges the gap between previous theoretical and experimental studies, providing insights into the timescale of this phase transition.

58 GEOSCIENCES↗

DOE OSTI2025

In-Pile Irradiation Induced Defects and the Effect on Thermal Diffusivity of MgO

The effects of neutron irradiation temperature and dose on thermal diffusivity are compared between non-irradiated and in-pile irradiated MgO samples. MgO pellets were irradiated in-pile of the Advanced Test Reactor at Idaho National Laboratory. Samples were irradiated at 623 and 973 K to fast neutron fluences of 1 x 1025 (1.5 dpa) and 2 x 1025 n/m2 (3 dpa). Post irradiation examination included X-ray diffraction, scanning electron microscopy, laser flash thermal diffusivity, and transmission electron microscopy. The radiation induced thermophysical and structural evolution of MgO is reported

T. Moorea, Donald↗

NASA NTRS1973

Grain boundary mobility in anion doped MgO

Certain anions OH(-), F(-) and Gl(-) are shown to enhance grain growth in MgO. The magnitude of their effect decreases in the order in which the anions are listed and depends on their location (solid-solution, second phase) in the MgO lattice. As most anions exhibit relatively high vapor pressures at sintering temperatures, they retard densification and invariably promote residual porosity. The role of anions on grain growth rates was studied in relation to their effect on pore mobility and pore removal; the atomic process controlling the actual rates was determined from observed kinetics in conjunction with the microstructural features. With respect to controlling mechanisms, the effects of all anions are not the same. OH(-) and F(-) control behavior through creation of a defect structure and a grain boundary liquid phase while Cl(-) promotes matter transport within pores by evaporation-condensation. Studies on an additional anion, S to the minus 2nd power gave results which were no different from undoped MgO, possibly because of evaporative losses during hot pressing. Hence, the effect of sulphur is negligible or undetermined.

Kapadia, C. M.↗

NASA NTRS1992

Crystalline orientations of Tl2Ba2Ca2Cu3O(x) grains on MgO, SrTiO3, and LaAlO3 substrates

Crystalline orientations of Tl2Ba2Ca2Cu3O(x) grains in magnetron sputtered films on MgO (001), SrTiO3 (001), and LaAlO3 (001) substrates were investigated by scanning electron microscopy. In contrast to the nearly single crystalline films on the lattice matched substrates SrTiO3 and LaAlO3, films on the MgO (001) substrate, being polycrystalline in nature, exhibit several preferred in-plane grain orientations. These orientations agree well with a simplified theory of near-coincidence site lattices between Tl2Ba2Ca2Cu3O(x) and MgO.

Liou, S. H.↗

DOE OSTI2024

The intrinsic mechanical properties of hydromagnesite, Mg 5 (CO 3 ) 4 (OH) 2 ·4H 2 O, a key phase of reactive MgO carbonate cement

To potentially enable CO 2 sequestration, reactive MgO carbonate cement is emerging as an alternative binder to Portland cement. Understanding the mechanical properties of its binding phase is critical for understanding the strength development and performing materials design for reactive MgO cement systems; however, the intrinsic mechanical properties of hydromagnesite (Mg 5 (CO 3 ) 4 (OH) 2 ·4H 2 O), a key binding phase, remain unexplored. Here the present study utilized synchrotron-based high-pressure X-ray diffraction to determine the unit cell-scale, intrinsic mechanical properties of hydromagnesite for the first time. Up to hydrostatic loading of 7.7 GPa, the bulk modulus of hydromagnesite was determined as 59 GPa or 71 GPa fitted using the second-order or third-order Birch-Murnaghan equation of state, which we contextualize with binding phases in various cement systems. The experiment results are applicable in materials design of low-carbon concrete and valuable for the validation and calibration of atomistic models.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Transparent MgO for Back-Contact Passivation of CdTe-Based Solar Cells

The passivating effects of MgO have been studied by integrating into an existing superstrate CdTe thin film solar cell device architecture. When implemented as an emitter to replace the typical MZO, the device performance was below par, but improved PL and TRPL was detected with significant carrier lifetimes in comparison to the MZO devices. However, when integrated at the back, the PL signal was detected upon the illumination of excitation laser from the back. This has opened the possibility of probing the back of the CdTe thin film solar cells with transparent back contact with improved back passivation and a bifacial device structure. Further, the TRPL measurements suggests that the MgO shows passivating effects to a CdTe surface irrespective of method of deposition implemented.

bifacial↗

DOE OSTI2021

Producing cement clinker assemblages in the system: CaO-SiO2-Al2O3-SO3-CaCl2-MgO

Highlights: • Alinite formation conditions are optimised. • Ye'elimite and alinite cannot be simultaneously produced. • Ternesite and chlormayenite are compatible at 1150 °C. • Alite is formed at a reduced temperature of 1300 °C. • Wadalite and chlorellestadite can incorporate chloride in cement clinker assemblages. The cement industry is carbon-intensive, and the valorisation of industrial side-streams/residuals for use as alternative raw materials can enable the cement industry to reduce its carbon footprint as well as promote resource efficiency. Apart from key clinker ingredients such as CaO, Al{sub 2}O{sub 3}, and SiO{sub 2}, industrial residues can also contain MgO, CaCl{sub 2}, and SO{sub 3}. Therefore, this study investigates the formation of cement clinker assemblages in the system CaO-SiO{sub 2}-Al{sub 2}O{sub 3}-SO{sub 3}-CaCl{sub 2}-MgO at temperatures ranging between 1100 and 1300 °C. The production of a clinker composed mainly of alinite and ye'elimite is first attempted; it is found that these phases cannot be simultaneously produced. Ternesite is also not compatible with alinite under the conditions studied. Wadalite is compatible with both ye'elimite and ternesite, while ternesite is also compatible with chlormayenite at 1150 °C. Additionally, the low-temperature formation of alite was also observed with the presence of CaCl{sub 2} in the raw-material mix.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Use of kaolinite clays in development of a low carbon MgO-clay binder system

Magnesium oxide based cements may provide a promising alternative to the conventional Portland cement in many applications. This study investigates the feasibility of using calcined kaolinitic clay to produce an MgO binder. The MgO-based binder were prepared using a low kaolinite content clay and metakaolin and were compared with a silica fume system. Implications of the addition of magnesium carbonate in the binder were also investigated. Isothermal calorimetry, X-ray diffraction (XRD), thermogravimetric analysis (TGA) and Fourier transform infrared spectroscopy (FTIR) were used to study the hydration characteristics of the binder system whereas compressive strength and porosity were measured to determine mechanical and durability attributes. The economic and environmental aspects of the binder system is also discussed. Hydrotalcite like phases were clearly produced on hydration in the clay mixes containing carbonate additions. The compressive strength of clay mixes was at par or better compared to systems containing silica fume, and the clay systems had significantly lower porosity levels. The presence of magnesium carbonate further enhanced the physical properties of the clay mixes.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Spin canting of Ni/CoO/Fe films grown on curved MgO(0 0 1) substrate

Using element-resolved x-ray magnetic circular dichroism (XMCD) and x-ray magnetic linear dichroism (XMLD) measurements, we determined the spin orientations of Ni, CoO and Fe films in Ni/CoO/Fe films grown on a curved MgO(0 0 1) substrate. We find that the vicinal surface of MgO(0 0 1) substrate results in a spin canting towards out-of-plane direction in the Ni and CoO films as a result of the interfacial coupling. The Ni spin canting angle increases monotonically with the vicinal angle in the studied range of 0–17° and the CoO spin canting angle increases more rapidly towards saturation only at a few degrees of the vicinal angle. The uniaxial magnetic anisotropy induced in the Ni layer by the Ni/CoO interfacial coupling is quantitatively determined and is shown to increase monotonically with the vicinal angle. Our result provides a new pathway for tailoring the spin orientation by modifying the substrate surface symmetry in combining with the ferromagnetic/antiferromagnetic interfacial interaction in thin-film based spintronic devices.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Experimental and theoretical investigation of the crystalline surface, film, and interface properties of antiperovskite Mn 3 GaN grown by molecular beam epitaxy on MgO(001)

Here, we present a study of the epitaxial growth, characterization, and theoretical modeling of thin film antiperovskite Mn 3 GaN, an antiferromagnetic material with kagome structure which is grown on MgO (001) substrates using N-plasma-assisted molecular beam epitaxy. Reflection high energy electron diffraction is used to assess the in-plane evolution of the film structure during growth, and the surface is investigated in-situ using scanning tunneling microscopy and Auger electron spectroscopy. These results are combined with precision measurements done ex-situ determining the film lattice constants using a combination of x-ray diffraction with reciprocal space mapping and scanning transmission electron microscopy. Overall, a uniform, homogeneous film with an atomically smooth vacuum surface and atomically sharp substrate interface is found having very small in-plane tensile strain and mild out-of-plane compressive strain. First-principles theoretical calculations are applied in order to ascertain the lowest energy models for both the Mn 3 GaN surface and the Mn 3 GaN/MgO film/substrate interface. Models including MnGa versus MnN surface layers and MnGa versus MnN interfacial layers are considered as functions of both the Mn and Ga chemical potentials. The predictions are discussed in comparison to the experimental results. The overall findings suggest that Mn 3 GaN on MgO(001) is a viable epitaxial film which can be further explored in connection with antiferromagnetic spintronics.

Density functional theory↗

DOE OSTI2023

Catalysts Prepared from Atomically Dispersed Ce(III) on MgO Rival Bulk Ceria for CO Oxidation

Atomically dispersed cerium catalysts on an inert, crystalline MgO powder support were prepared by using both Ce(III) and Ce(IV) precursors. The materials were used as catalysts for CO oxidation in a once-through flow reactor and characterized by atomic-resolution scanning transmission electron microscopy, X-ray absorption near edge structure spectroscopy, X-ray photoelectron spectroscopy, and temperature-programmed reduction, among other techniques, before and after catalysis. The most active catalysts, formed from the precursor incorporating Ce(III), displayed a performance similar to that reported for bulk ceria under comparable conditions. The catalyst provided stable time-on-stream performance for as long as it was kept on stream, two days, increasing slightly in activity as the atomically dispersed cerium ions were transformed into ceria nanodomains represented as CeO x and having increased reducibility on the MgO support. Furthermore, the results suggest how highly dispersed supported ceria catalysts with low cerium loadings can be prepared and may pave the way to improved efficiencies of cerium utilization in oxidation catalysis.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Epitaxial growth of rock salt MgZrN 2 semiconductors on MgO and GaN

Ternary nitride compound semiconductors have attracted recent attention as electronic materials since their properties can be tuned by cation stoichiometry and ordering. A recently discovered example is MgZrN 2 , a ternary analog to the rock salt semiconductor ScN. MgZrN 2 has a larger bandgap and stronger dielectric response than the binary compound. Polycrystalline thin films of MgZrN 2 have been studied, but demonstration of high-quality growth is still required to establish its suitability for technological applications. Here, we report on epitaxial growth of MgZrN 2 thin films on (100) and (111) MgO substrates and (001) GaN templates. The MgZrN 2 composition is confirmed by Rutherford backscattering spectrometry, showing no oxygen in the film except for a thin surface oxide layer. Epitaxial growth results in MgZrN 2 with x-ray diffraction rocking curves with a full-width at half-maximum in the range of 0.3–3.0°, depending on the substrate. Transmission electron microscopy analysis of the MgZrN 2 film grown on a (111) MgO substrate confirms epitaxial growth and shows a sharp film/substrate interface. In-plane temperature-dependent Hall effect measurements show that the material is an n-type semiconductor with a relatively high concentration ( n 300K ≈ 10 19 –10 20 cm -3 ) of thermally activated electrons. Room-temperature transport measurements show a conductivity of 25 S cm -1 and a Seebeck coefficient of -80 μ V K -1 . Overall, these results provide an important step toward integration of rock salt MgZrN 2 with other technological nitrides for device applications.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Many-body effects for the Mg 2s XPS of MgO

The energy separation of the higher lying cation XPS binding energies, BEs, for MgO is examined. It is shown that the Hartree–Fock BEs overestimate the separation of the Mg BE(2s) and BE(2p), because an important many-body effect is neglected in the determination of the Hartree–Fock BEs. Once the many-body effect is taken into account, there is good agreement between theory and the XPS measurement. The character of this atomic many-body effect is established in terms of a nearly degenerate configuration that is needed to describe the wavefunction when an Mg 2s electron is ionized. Further, the results provide additional evidence of the ionic character of the MgO crystal. Given the atomic character of the many-body effect, it is likely to apply also to the BE separations of other closed shell oxides.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2024

Polarization-dependent photoluminescence of Ce-implanted MgO and MgAl 2 O 4

Since the qubit's performance of solid-state spin centers depends highly on the host material, spin centers using new host materials may offer new qubit applications. We investigate the optical properties of Ce-implanted MgO and MgAl 2 O 4 as potential materials holding the optically accessible qubit. We find that the photoluminescence of Ce-implanted MgAl 2 O 4 is more than 10 times brighter than that of Ce-implanted MgO and observe polarization-dependent emission of Ce center in MgAl 2 O 4 with 2% at 4 K under 500 mT, suggesting that the properties required for initializing and reading the state of the spin qubit have been achieved.

42 ENGINEERING↗

NASA NTRS1977

Influence of adsorbed fluids on the rolling contact deformation of MgO single crystals

Basic phenomena associated with rolling contact deformation were studied using MgO as a model bearing material. A hardened steel ball was rolled on MgO single crystals in slow-speed reciprocating motion and in high-speed circular motion. The resulting deformation was studied by dislocation etch-pit techniques. The presence of adsorbed fluids, such as silicone oil, white mineral oil, and toluene, with slow-speed sliding caused a dramatic change in slip mode and premature surface spalling compared with similar experiments in air or under water. In contrast, dimethyl formamide inhibited these slip processes. The results are consistent with the dependence of dislocation mobility on adsorbed species. High-speed hydrodynamic rolling with mineral oil lubrication produced a different slip phenomena entirely from the slow-speed rolling. The slip bands resembled those produced in tensile tests, and all slip apparently initiated at subsurface sites.

Dufrane, K. F.↗

NASA NTRS1981

Effect of CeO2, MgO and Y2O3 additions on the sinterability of a milled Si3N4 with 14.5 wt% SiO2

The sinterability of alpha Si3N4 with 0-5.07 equivalent per cent of CeO2, MgO, or Y2O3 has been studied in the temperature range 1650-1820 C by density measurements and X-ray diffraction analysis. Maximum densities were obtained in the range 1765-1820 C and were 99.6% of theoretical with 2.5% CeO2; 98.5% of theoretical with 1.24 to 1.87% MgO, and 99.2% of theoretical with 2.5% Y2O3. Densities 94% or more of theoretical value were obtained with as little as 0.62 equivalent per cent additive.

Arias, A.↗