Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Measurement_method”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Experiments in determining the outgassing of spacecraft in the vacuum environment

As spacecraft become more sophisticated, their contamination becomes of increasing concern. The use of real-time monitors, such as the quartz crystal microbalance, and post-test methods such as the chemical analysis of residuals, has been combined with a number of analytical techniques in contamination-related investigations at the Goddard Space Flight Center. These include the establishment of the cause of an orbital failure, the determination of component outgassing rates, and the monitoring of contaminants in vacuum chambers and in orbit. Improved capabilities appear possible with measurement methods such as attenuated total reflectance and better analytical modeling of the contaminant flux environment.

Kruger, R.↗
NASA NTRS1975

Review of Terrestrial Photovoltaic Measurements Workshop

Measurement methods for terrestrial solar cells require calibration standards to set simulator irradiance levels or to monitor solar irradiance in outdoor measurements. Measurements of solar cell performance in terrestrial sunlight are the most acceptable, but an artificial light source can be used for laboratory measurements.

Brandhorst, H. W., Jr.↗
NASA NTRS1975

Metabolism and heat dissipation during Apollo EVA periods

The extravehicular activity life support equipment, suit temperature control, metabolic rate measurement methods, and energy production are discussed. The Apollo crewmen were able to perform planned extravehicular activities and to extend them to the maximum time allowable without medical problems. The metabolic rates experienced during the lunar surface extravehicular activities were lower than conservative premission estimates. A manually controlled liquid cooling garment was effectively used to minimize fatigue and water loss from sweating during lunar surface extravehicular activities. Gas cooling was adequate during the short zero-g extravehicular activities performed from the command module. The prediction of EVA workloads became more reliable as inflight data was accumulated. The prediction of the average metabolic cost of an EVA was more reliable than the cost of an individual short-term task.

J.M. Waligora↗
NASA NTRS1975

Preliminary design study. Shuttle modular scanning spectroradiometer

Fundamental concepts on which to base a detailed design for a Shuttle Modular Scanning Spectroradiometer were developed, and a preliminary design is presented. The recommended design features modularity and flexibility. It includes a 75-cm f/1.7-telescope assembly in an all-reflective Schmidt configuration, a solid state scan system (pushbroom) with high resolution over a 15 deg field of view, and ten detector channels covering the spectral range from 0.45 to 12.5 micrometers. It uses charge transfer device techniques to accommodate a large number of detector elements for earth observation measurements. Methods for in-flight radiometric calibration, for image motion compensation, and for data processing are described. Recommendations for ground support equipment are included, and interfaces with the shuttle orbiter vehicle are illustrated.

Source record↗
NASA NTRS1975

International Symposium on Remote Sensing of Environment, 10th, University of Michigan, Ann Arbor, Mich., October 6-10, 1975, Proceedings. Volumes 1 & 2

Topics treated include the application of a Fourier transform spectrometer to infrared remote sensing, the performance optimization of a satellite-borne thematic mapper, a data handling system to be integrated with a digital airborne multispectral scanner, infrared thermography for micro- and mesometeorological measurements, satellite interrogated data collection platforms for river and flood forecasting and the automatic measurement of sea surface temperature from a GOES satellite. Solar and atmospheric effects on satellite imagery derived from aircraft reflectance measurements, methods for determining haze levels from multispectral scanner data, restoration of Landsat images by discrete two-dimensional deconvolution and the automatic classification of aircraft and satellite multispectral images using mixed integer programming are also discussed. Individual items are announced in this issue.

Source record↗
NASA NTRS1975

Airborne laser bathymeter

A description is given of a program concerned with the development and the evaluation of techniques for the measurement of water depth with a pulsed laser. Airborne laser bathymetry makes use of a light pulse which is sent downward. Information concerning the water depth is provided by the time interval observed between the arrival of the light pulse reflected from the water surface and the arrival of the pulse coming from the ocean floor. Details concerning the instrumentation used for the developed measurement method are discussed. Attention is also given to field experiments and aspects of system performance.

Cervenka, P. O.↗
NASA NTRS1977

Development of a transfer function method for dynamic stability measurement

Flutter testing method based on transfer function measurements is developed. The error statistics of several dynamic stability measurement methods are reviewed. It is shown that the transfer function measurement controls the error level by averaging the data and correlating the input and output. The method also gives a direct estimate of the error in the response measurement. An algorithm is developed for obtaining the natural frequency and damping ratio of low damped modes of the system, using integrals of the transfer function in the vicinity of a resonant peak. Guidelines are given for selecting the parameters in the transfer function measurement. Finally, the dynamic stability measurement technique is applied to data from a wind tunnel test of a proprotor and wing model.

Johnson, W.↗
NASA NTRS1979

Mechanical and thermophysical properties of graphite/polyimide composite materials

An on-going program to characterize advanced composites for up to 50,000 hours of exposure to simulated supersonic cruise environments is summarized. Results are presented for up to 25,000 hours of thermal exposure and 10,000 hours of flight simulation at temperatures up to 560K (550 F) with emphasis on HTS/710 graphite/polyimide composite material. Results to date indicate that the maximum use temperature for HTS/710 may be reduced to 505K (450 F) for long-time (1000 hours) application such as the supersonic transport. Preliminary thermophysical properties data for HTS/PMR15 graphite/polyimide were generated. These data include thermal conductivity, thermal expansion, and specific heat from 115K (-252 F) to 590K (600 F) and emittance at room temperature and 590K (600 F). The purpose in generating these data was to validate use of state-of-the-art property measurement methods for advanced graphite fiber reinforced resin matrix composites. Based on results to this point, thermal expansion measurements for composites are most difficult to perform. A high degree of caution in conducting thermal expansion tests and analyzing results is required to produce reliable data.

Rummler, D. R.↗
NASA NTRS1979

Design fabrication and installation of a yaw measuring device

The results of work performed in the development and testing of a yaw measuring device are summarized. A review of the yaw measurement method; and the techniques and hardware needed for its implementation are presented. A description and summary of the tests performed at the U.S. Bureau of Mines Bruceton facility are included. Conclusions are summarized and recommendations for a unit capable of operation in a mine environment are presented.

Source record↗
NASA NTRS1979

A self pulsed laser ranging system under development at 'JPL'

The performance of large space deployable antenna reflectors to be used for broad-based communications systems is largely dependent on the accuracy with which the surface figure can be constructed and maintained. The paper examines various surface distortion tolerance and measurement requirements for various classes of communication antennas. Several surface measuring methods are described including a self-pulsed laser ranging system.

Berdahl, M.↗
NASA NTRS1980

Gigahertz analog modulation and differential delay of GaAlAs lasers - Temperature and current behavior

Gigahertz analog modulation characteristics of broad-area commercially available GaAlAs lasers have been investigated as a function of temperature and current in the vicinity of the upper frequency limit, where the resonance phenomena occur. The optimum temperature for small-signal amplitude modulation was found to be around -15 C for our particular broad-stripe geometry double-heterostructure laser. The Q was found to increase by a factor of 2 and the bandwidth by about 2%; the external quantum efficiency was maximized in this range. The optimum dc current bias was about 2% above the threshold current. Differential delays have also been measured down to a few picosecond accuracy by a unique phase-angle measurement method using a vector voltmeter. Some of the temperature effects observed may be related to mode changes and multimode and superradiance behavior.

Eng, S. T.↗
NASA NTRS1979

Grain quality inspection system

A review of grain quality indicators and measurement methods was conducted in order to assess the feasibility of using remote sensing technology to develop a continuous monitoring system for use during grain transfer operations. Most detection methods were found to be too slow or too expensive to be incorporated into the normal inspection procedure of a grain elevator on a continuous basis. Two indicators, moisture content and broken corn and foreign material, show potential for automation and are of an economic value. A microprocessor based system which utilizes commercially available electronic moisture meter was developed and tested. A method for automating BCFM measurement is described. A complete system description is presented along with performance test results.

Flood, C. A., Jr.↗
NASA NTRS1980

Active microwave water equivalence

Measurements of water equivalence using an active FM-CW microwave system were conducted over the past three years at various sites in Colorado, Wyoming, and California. The measurement method is described. Measurements of water equivalence and stratigraphy are compared with ground truth. A comparison of microwave, federal sampler, and snow pillow measurements at three sites in Colorado is described.

Boyne, H. S.↗
NASA NTRS1981

Sources of atmospheric methane - Measurements in rice paddies and a discussion

Field measurements of methane fluxes from rice paddies, fresh water lakes, and saltwater marshes have been made to infer estimates of the size of these sources of atmospheric methane. The rice-paddy measurements, the first of their kind, show that the principal means of methane escape is through the plants themselves as opposed to transport across the water-air interface via bubbles or molecular diffusion. Nitrogen-fertilized plants release much more methane than unfertilized plants but even these measured rates are only one fourth as large as those inferred earlier by Koyama (1963, 1964) and on which all global extrapolations have been based to date. Measured methane fluxes from lakes and marshes are also compared to similar earlier data and it is found that extant data and flux-measurement methods are insufficient for reliable global extrapolations.

Cicerone, R. J.↗
NASA NTRS1940

Pressure and temperature measurement in supercharger investigations

With the further development of the supercharger, requirements with regard to measuring accuracy increase while at the same time the conditions under which the measurements must be carried out become more difficult. The present paper is a contribution toward the improvement and refinement of the measuring methods. For pressure measurements some suggestions are made with regard to design and location of the measuring stations. The question of temperature measurement in rapid air flow is discussed, new instruments for the direct measurement of the temperature in the rapid airstream are described and the results obtained with the various instruments presented.

Franz, A↗
NASA NTRS1939

Experiments on a Slotted Wing

The results of pressure distribution measurements that were made on a model wing section of a Fieseler F 5 R type airplane are presented. Comparison of those model tests with the corresponding flight tests indicates the limitations and also the advantages of wind tunnel investigations, the advantages being particularly that through the variety of measuring methods employed the more complicated flow conditions may also be clarified. A fact brought out in these tests is that even in the case of "well rounded" slots it is possible for a vortex to be set up at the slot entrance and this vortex is responsible for certain irregularities in the pressure distribution and in the efficiency of the slot.

Ruden, P↗
NASA NTRS1944

Researches on the Piston Ring

In internal combustion engines, steam engines, air compressors, and so forth, the piston ring plays an important role. Especially, the recent development of Diesel engines which require a high compression pressure for their working, makes, nowadays, the packing action of the piston ring far more important than ever. Though a number of papers have been published in regard to researches on the problem of the piston ring, none has yet dealt with an exact measurement of pressure exerted on the cylinder wall at any given point of the ring. The only paper that can be traced on this subject so far is Mr. Nakagawa's report on the determination of the relative distribution of pressure on the cylinder wall, but the measuring method adopted therein appears to need further consideration. No exact idea has yet been obtained as to how the obturation of gas between the piston and cylinder, the frictional resistance of the piston, and the wear of the cylinder wall are affected by the intensity and the distribution of the radial pressure of the piston ring. Consequently, the author has endeavored, by employing an apparatus of his own invention, to get an exact determination of the pressure distribution of the piston ring. By means of a newly devised ring tester, to which piezoelectricity of quartz was applied, the distribution of the radial pressure of many sample rings on the market was accurately determined. Since many famous piston rings show very irregular pressure distribution, the author investigated and achieved a manufacturing process of the piston ring which will exert uniform pressure on the cylinder wall. Temperature effects on the configuration and on the mean spring power have also been studied. Further, the tests were performed to ascertain how the gas tightness of the piston ring may be affected by the number or spring power. The researches as to the frictional resistance between the piston ring and the cylinder wall were carried out, too. The procedure of study, and experiments conducted by the author, on this subject will be fully described in the following paragraphs.

Ehihara, Keikiti↗