Results for “Manufactured Materials” — Page 4

NASA NTRS2015

Materials, Manufacturing, and Test Development of a Composite Fan Blade Leading Edge Subcomponent for Improved Impact Resistance

Application of polymer matrix composite materials for jet engine fan blades is becoming attractive as an alternative to metallic blades; particularly for large engines where significant weight savings are recognized on moving to a composite structure. However, the weight benefit of the composite is offset by a reduction of aerodynamic efficiency resulting from a necessary increase in blade thickness; relative to the titanium blades. Blade dimensions are largely driven by resistance to damage on bird strike. Further development of the composite material is necessary to allow composite blade designs to approximate the dimensions of a metallic fan blade. The reduction in thickness over the state of the art composite blades is expected to translate into structural weight reduction, improved aerodynamic efficiency, and therefore reduced fuel consumption. This paper presents test article design, subcomponent blade leading edge fabrication, test method development, and initial results from ballistic impact of a gelatin projectile on the leading edge of composite fan blades. The simplified test article geometry was developed to realistically simulate a blade leading edge while decreasing fabrication complexity. Impact data is presented on baseline composite blades and toughened blades; where a considerable improvement to impact resistance was recorded.

Materials↗

DOE OSTI2021

Roll-to-Roll Advanced Materials Manufacturing DOE Laboratory Collaboration (FY2020 Final Report)

R2R processing is used to manufacture a wide range of products for various applications which span many industrial business sectors. The overall R2R methodology has been in use for decades and this continuous technique traditionally involves deposition of material(s) onto moving webs, carriers or other continuous belt-fed or conveyor-based processes that enable successive steps to build a final version which serves to support the deposited materials. Established methods that typify R2R processing include tape casting, silk-screen printing, reel-to-reel vacuum deposition/coating, and R2R lithography. Products supported by R2R manufacturing include micro-electronics, electro-chromic window films, PVs, fuel cells for energy conversion, battery electrodes for energy storage, and barrier and membrane materials. Due to innovation in materials and process equipment, high-quality yet very low-cost multilayer technologies have the potential to be manufactured on a very cost-competitive basis. To move energy-related products from high-cost niche applications to the commercial sector, the means must be available to enable manufacture of these products in a cost-competitive manner that is affordable. Fortunately, products such as fuel cells, thin- and mid-film PVs, batteries, electrochromic and piezoelectric films, water separation membranes, and other energy saving technologies readily lend themselves to manufacture using R2R approaches. However, more early-stage research is needed to solve the challenge of linking the materials (particles, polymers, solvents, additives) used in ink and slurry formulations and the coating and drying processes to the ultimate performance of the final R2R product, especially for a process that uses multiple layers of deposition to achieve the end product. To solve the problems associated with these challenges, the R2R Collaboration is executing a research program with outcomes that will ultimately link modeling, processing, metrology and defect detection tools, thereby directly relating the properties of constituent particles and processing conditions to the performance of final devices. This collaborative approach was designed to foster identification and development of materials and processes related to R2R for clean-energy materials development. Using computational and experimental capabilities by acknowledged subject matter experts within the supported National Laboratory system, this project leverages the capabilities and expertise at each of five National Laboratories to further the development of multilayer technologies that will enable high-volume, cost-competitive platforms. A typical R2R process has three steps: (1) mixing of particles and various constituents in a slurry, (2) coating of the ink/slurry mixture on a substrate, and (3) drying/curing and processing of the coating. Final performance of devices made via R2R processes is dependent on the active materials (e.g., electrochemical particles in battery or fuel cell electrodes) and the device structure that stems from the governing component interactions within the various steps. However, a fundamental understanding of the underlying mechanisms and phenomena is still lacking, which is why industrial-scale R2R process development and manufacturing is still largely empirical in nature. The FY 2019 through FY 2021 program addresses aspects of the following two targets from the AMO Multi-Year Program Plan: (1) Target 8.1 Develop technologies to reduce the cost per manufactured throughput of continuous R2R manufacturing processes. (A) Increasing throughput of R2R processes by 5 times for batteries (to 50 square feet per minute (50 ft 2 /min)) and capacitors and 10 times for printed electronics and the manufacture of other substrates and MEs used in support of these products. (B) Developing resolution capabilities to enable registration and alignment that will detect, align, and co-deposit multiple layers of coatings and print < 1-micron (1 µm) features using continuous process scalable for commercial production. (C) Developing scalable and reliable R2R processes for solution deposition of ultra-thin (<10 nm) films for active and passive materials. (D) Develop in-line multilayer coating technology on thin films with yields greater than 95%. (2) Target 8.2 Develop in-line instrumentation tools that will evaluate the quality of single and multilayer materials in-process. (A) Developing in-line QC technologies and methodologies for real-time identification of defects and expected product properties “in-use/application” during continuous processing at all size-scales with a focus on the “micro” and “nano” scale traces, lines, and devices, i.e., <1 μm at 300 ft./min for R2R processing in air and <10 nm at 20 ft./min for vacuum (B) Developing technologies to increase the measurement frequency of surface rheology without significant cost increases with a goal of a 10-nanometer in-line profilometry at a production rate of 100,000 square millimeters per minute (100,000 mm 2 /min).

42 ENGINEERING↗

DOE OSTI2020

Roll-to-Roll Advanced Materials Manufacturing DOE Laboratory Collaboration (FY2019 Final Report)

R2R processing is used to manufacture a wide range of products for various applications which span many industrial business sectors. The overall R2R methodology has been in use for decades and this continuous technique traditionally involves deposition of material(s) onto moving webs, carriers or other continuous belt-fed or conveyor-based processes that enable successive steps to build a final version which serves to support the deposited materials. Established methods that typify R2R include tape casting, silk-screen printing, reel-to-reel vacuum deposition/coating and R2R lithography. Products supported by R2R manufacturing include micro-electronics, electro-chromic window films, PVs, fuel cells for energy conversion, battery electrodes for energy storage, and barrier and membrane materials. Due to innovation in materials and process equipment, high-quality yet very low-cost multilayer technologies have the potential to be manufactured on a very cost-competitive basis. To move energy-related products from high-cost niche applications to the commercial sector, a means must be available to enable manufacture of these products in a cost-competitive manner that is affordable. Fortunately, products such as fuel cells, thin- and mid-film PVs, batteries, electrochromic and piezoelectric films, water separation membranes, and other energy saving technologies readily lend themselves to manufacture using R2R approaches. However, more early-stage research is needed to solve the challenge of linking the materials (particles, polymers, solvents, additives) used in ink and slurry formulations, though the ink processing, coating and drying processes, to the ultimate performance of the final R2R product, especially for a process that uses multiple layers of deposition to achieve the end product.

42 ENGINEERING↗

DOE OSTI2025

Assessing the viability of a new subsize tensile specimen geometry for evaluation of structural nuclear and additively manufactured materials

The use of subsize specimens in nuclear materials testing has been a subject of ongoing interest due to radiation safety concerns and resource conservation needs. It is also of interest in additive manufacturing (AM), also known as 3D-printing, as subsize specimens can more accurately represent the behavior of the small, intricate geometries often produced using AM. A novel, extremely small geometry, called the Subsize Teeny (SST) was recently developed and is of interest for implementation. Given its extraordinarily small size and the complexities associated with subsize specimen testing, adequate vetting of this geometry is necessary to ensure data quality. Here, a variety of unirradiated nuclear structural materials were tested in the SST geometry and compared against the well-established SSJ3 geometry. In addition, two case studies implementing the SST as a screening geometry for AM materials were also conducted. The question of SST viability was found to be highly nuanced and will often be dependent on the context or application in question. It was determined, however, that the SST is a largely invalid geometry for exceptionally coarse-grained materials or in cases where the physical defect volume equals or exceeds 0.1 % or where the specimen machining parameters result in significant surface alterations. On the other hand, it was determined that the SST may be employed with confidence if the test material is nearly or totally free of physical defects, isotropic, demonstrates homogeneous plastic deformation, and possesses a fine-grained, nearly or totally homogeneous microstructure with at least twelve slip systems.

Additive manufacturing↗

DOE OSTI2019

Shortening the Design and Certification Cycle for Additively Manufactured Materials by Improved Mesoscale Simulations and Validation Experiments: Fiscal Year 2019 Status Report.

This report outlines the fiscal year (FY) 2019 status of an ongoing multi-year effort to develop a general, microstructurally-aware, continuum-level model for representing the dynamic response of material with complex microstructures. This work has focused on accurately representing the response of both conventionally wrought processed and additively manufactured (AM) 304L stainless steel (SS) as a test case. Additive manufacturing, or 3D printing, is an emerging technology capable of enabling shortened design and certification cycles for stockpile components through rapid prototyping. However, there is not an understanding of how the complex and unique microstructures of AM materials affect their mechanical response at high strain rates. To achieve our project goal, an upscaling technique was developed to bridge the gap between the microstructural and continuum scales to represent AM microstructures on a Finite Element (FE) mesh. This process involves the simulations of the additive process using the Sandia developed kinetic Monte Carlo (KMC) code SPPARKS. These SPPARKS microstructures are characterized using clustering algorithms from machine learning and used to populate the quadrature points of a FE mesh. Additionally, a spall kinetic model (SKM) was developed to more accurately represent the dynamic failure of AM materials. Validation experiments were performed using both pulsed power machines and projectile launchers. These experiments have provided equation of state (EOS) and flow strength measurements of both wrought and AM 304L SS to above Mbar pressures. In some experiments, multi-point interferometry was used to quantify the variation is observed material response of the AM 304L SS. Analysis of these experiments is ongoing, but preliminary comparisons of our upscaling technique and SKM to experimental data were performed as a validation exercise. Moving forward, this project will advance and further validate our computational framework, using advanced theory and additional high-fidelity experiments.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Roll-to-Roll Advanced Materials Manufacturing DOE Laboratory Collaboration - Early Stage R&D: Phase 2 and FY21 (Final Report)

R2R processing is used to manufacture a wide range of products for various applications which span many industrial business sectors. The overall R2R methodology has been in use for decades and this continuous technique traditionally involves deposition of material(s) onto substrates or membranes that are on moving webs, carriers or other continuous belt-fed or conveyor-based processes that enable successive steps to build a final product. Established methods that typify R2R processing include tape casting, silk-screen printing, reel-to-reel vacuum deposition/coating, and R2R lithography. Products supported by R2R manufacturing include micro-electronics, electro-chromic window films, PVs, fuel cells for energy conversion, battery electrodes and electrolytes for energy storage, and barrier and membrane materials for decarbonization and air and water filtration. Due to innovation in materials and process equipment, high-quality yet very low-cost multilayer technologies have the potential to be manufactured on a very cost-competitive basis. To move energy-related products from high-cost niche applications to the commercial sector, the means must be available to enable manufacture of these products in a cost-competitive manner. Fortunately, products such as fuel cells, thin- and mid-film PVs, batteries, electrochromic and piezoelectric films, water separation membranes, and other energy saving technologies readily lend themselves to manufacture using R2R approaches. However, more early-stage research is needed to solve the challenge of linking the materials (particles, polymers, solvents, additives) used in ink and slurry formulations and the coating and heated drying processes to the ultimate performance of the final R2R product, especially for a process that uses multiple layers of deposition to achieve the end product.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Characterization of nonlinear ultrasonic waves behavior while interacting with poor interlayer bonds in large-scale additive manufactured materials

Over the past decades, researchers have developed several nonlinear ultrasonic techniques for quality control of materials commonly used in different applications. Owing to the superior sensitivity of nonlinear ultrasound waves to small defects such as micro-cracks, their applicability in different nondestructive testing (NDT) problems has been investigated in numerous studies. These studies utilize frequency domain analysis to detect the generation of higher harmonics because of the formation of defects in the inspected medium. Frequency domain analysis based on the Fourier transform is a significant approach used in linear systems; however, it may not perform adequately on nonlinear systems. Hence, studies on nonlinear dynamics and physics consider analyzing systems' behavior in the phase-space domain. In contrast to the frequency domain analysis, which can result in information loss, analysis in the phase-space domain retains all the information regarding a system's states. Here, we investigate the nonlinearities induced by poor interlayer bonding in polymer-based additive manufactured parts in the phase-space domain. It is convenient to characterize the nonlinearity in the phase-space domain because it provides a geometrical representation of a system's states. Two types of low quality interlayer bond are considered. The first type is simulated artificially while the second type is manufactured by reducing the bond quality during the printing process. The analysis verified that the received ultrasonic signals exhibit classical nonlinear behavior in the phase-space domain while interacting with simulated poor interlayer bonds. In addition, the results showed that the behavior of ultrasonic waves is amplitude-dependent and evolves into models that have not been previously reported. Furthermore, Largest Lyapunov Exponent (LLE) is used to quantify the behavior of nonlinear ultrasonic waves while interacting with poor interlayer bonds. Using LLE, it was observed that the divergence rate of the phase-space trajectories depends on the amplitude of the excitation. This observation quantitatively proves that nonlinear behavior of ultrasound while interacting with poor interlayer bonds can be amplitude-dependent. The results of both simulated and inherent poor interlayer bond cases showed that LLE can be used as a reliable quantitative damage-sensitive feature to detect and potentially characterize weak bonds, which are difficult to detect using conventional approaches. Additionally, the reported results in the phase-space domain provide a basis for proposing a new mathematical model for ultrasonic waves interacting with poor interlayer bonds.

36 MATERIALS SCIENCE↗

NASA NTRS2017

NASA's In-Space Manufacturing Project: Materials and Manufacturing Process Development Update

The mission of NASA's In-Space Manufacturing (ISM) project is to identify, design, and implement on-demand, sustainable manufacturing solutions for fabrication, maintenance and repair during exploration missions. ISM has undertaken a phased strategy of incrementally increasing manufacturing capabilities to achieve this goal. The ISM project began with the development of the first 3D printer for the International Space Station. To date, the printer has completed two phases of flight operations. Results from phase I specimens indicated some differences in material properties between ground-processed and ISS-processed specimens, but results of follow-on analyses of these parts and a ground-based study with an equivalent printer strongly indicate that this variability is likely attributable to differences in manufacturing process settings between the ground and flight prints rather than microgravity effects on the fused deposition modeling (FDM) process. Analysis of phase II specimens from the 3D Printing in Zero G tech demo, which shed further light on the sources of material variability, will be presented. The ISM project has also developed a materials characterization plan for the Additive Manufacturing Facility, the follow-on commercial multimaterial 3D printing facility developed for ISS by Made in Space. This work will yield a suite of characteristic property values that can inform use of AMF by space system designers. Other project activities include development of an integrated 3D printer and recycler, known as the Refabricator, by Tethers Unlimited, which will be operational on ISS in 2018. The project also recently issued a broad area announcement for a multimaterial fabrication laboratory, which may include in-space manufacturing capabilities for metals, electronics, and polymeric materials, to be deployed on ISS in the 2022 timeframe.

Prater, Tracie↗

NASA NTRS1990

Integrated lunar materials manufacturing process

A manufacturing plant and process for production of oxygen on the moon uses lunar minerals as feed and a minimum of earth-imported, process materials. Lunar feed stocks are hydrogen-reducible minerals, ilmenite and lunar agglutinates occurring in numerous, explored locations mixed with other minerals in the pulverized surface layer of lunar soil known as regolith. Ilmenite (FeTiO.sub.3) and agglutinates contain ferrous (Fe.sup.+2) iron reducible by hydrogen to yield H.sub.2 O and metallic Fe at about 700.degree.-1,200.degree. C. The H.sub.2 O is electrolyzed in gas phase to yield H.sub.2 for recycle and O.sub.2 for storage and use. Hydrogen losses to lunar vacuum are minimized, with no net hydrogen (or any other earth-derived reagent) consumption except for small leaks. Feed minerals are surface-mined by front shovels and transported in trucks to the processing area. The machines are manned or robotic. Ilmenite and agglutinates occur mixed with silicate minerals which are not hydrogen-reducible at 700.degree.-1,200.degree. C. and consequently are separated and concentrated before feeding to the oxygen generation process. Solids rejected from the separation step and reduced solids from the oxygen process are returned to the mine area. The plant is powered by nuclear or solar power generators. Vapor-phase water electrolysis, a staged, countercurrent, fluidized bed reduction reactor and a radio-frequency-driven ceramic gas heater are used to improve thermal efficiency.

Gibson, Michael A.↗

DOE OSTI2019

Development of Pore-Free Ti-Si-C MAX/Al-Si Composite Materials Manufactured by Squeeze Casting Infiltration

Open-porous MAX phase skeletons from Ti{sub 3}SiC{sub 2} were manufactured by Microwave-Assisted Self-propagating High-temperature Synthesis (MASHS) and subsequently subjected to squeeze casting infiltration with an Al-Si lightweight casting alloy (EN AC-44200). This alloy was chosen due to its high flowability, corrosion resistance and good machinability. The manufactured composites, together with a reference sample of the original alloy, underwent testing of thermal properties, including thermal conductivity and diffusivity, specific heat and thermal expansion in the temperature range 50-500 °C, which corresponds to the expected working temperatures of the material. The fabricated AlSi/Ti{sub 3}SiC{sub 2} composites have significantly increased thermal stability, with coefficients of thermal expansion (approximately 10-11 × 10{sup −6} °C{sup −1}) half that of the original alloy. As regards mechanical properties, the instrumental Young’s modulus and Vickers hardness of the composite materials are 170.8 and 8.5 GPa, respectively. Moreover, the microstructure and phase composition, structural defects and potential impacts between constituents of the manufactured composites were characterized using SEM, TEM and STEM microscopy and EDS and XRD analysis.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Green Needle Coke Production from Pyrolysis Biocrude toward Bio-based Anode Material Manufacture: Biochar Fines Addition Effect as “Physical Template” on the Crystalline Order

Here, a new method for producing green needle coke (GNC) is developed by replacing the “heavy fraction” of petroleum pitch delayed coking with fast pyrolysis biocrude. A series of alternative biocrude distillation, carbonization, and calcination conditions were investigated to determine the influence of these processing parameters onto the crystalline structure of the resulting graphitized material. For the first time, the addition of biochar fines was found to serve as a “physical template” to increase the graphitic nature of the final product. During the initial biocrude carbonization (350–450 °C), volatile compounds are released, and aromatics in pyrolysis biocrude experience condensation, resulting in GNC solids with carbon contents above 95 wt % and some early lamellar structure. In the second stage of the thermal process (25–1500 °C), there are additional thermal decomposition reactions with an increase in the aromatic nature of the graphitized solid. It was found that systematic addition of biochar fines induces a nucleating effect during the GNC development. Thermogravimetric analysis suggests that biochar fines promote polycondensation reactions by modifying the biopitch structure and molecular weight, while elemental analysis (CHN) shows a reduction in both H/C and O/C ratios which are consistent with the increase in aromaticity and removal of oxygenated compounds as thermal treatment evolves. The effects of different bio-based pitch materials (after distillation) and GNC intermediates were evaluated by pyrolysis-gas chromatography mass spectrometry and Fourier transform infrared, displaying slight changes on product yields and quality. X-ray diffraction patterns taken after graphitization evidence an increase in the graphitic order with the addition of biochar fines. Transmittance electron microscopy depicts an improvement on graphitic morphology as biochar fine content increases. The use of biochar fines showed a significant increase in graphitic ordering at addition levels above 0.01 wt %. These results show that thermally treated biocrude/biochar fine systems can produce graphitic structures (hard carbon-like) that might be suitable for the manufacture of sodium-ion batteries.

09 BIOMASS FUELS↗

DOE OSTI2025

Advanced Materials & Manufacturing Technology (AMMT): Development of Additive Manufacturing Agnostic Process Parameter Procedure, 316H Stainless Steel Readiness Level Data Sets, and Machine Maintenance Plan

The University of California, Davis is involved in a project to deploy and enhance an artificial intelligence (AI) system for predicting and preventing plasma disruptions on the DIII D tokamak, under the funding from Department of Energy DE-SC0023500 (title: AI/Deep Learning FRNN Software for Prediction & Real-Time Control of DIII-D Plasma Control System (PCS)). The overarching goal is to demonstrate that real-time, AI-guided intervention can proactively modify the plasma state to avoid or mitigate disruptions—a critical challenge for the future of fusion energy.

36 MATERIALS SCIENCE↗

DOE OSTI2024