Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MT data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

The composition of gases from a diffusion flame above longleaf pine needle fuel beds

The gas and tar composition of a diffusion flame from longleaf pine needles is currently poorly understood and more data are needed to fill in the gap between pyrolysis data and smoke plume data, thus improving physical and chemical modeling of wildland smoke formation. A pilot experiment to measure light gas and tar composition of such a flame is described for three flame regions: persistent flame (flame base), intermittent flame, and smoke plume. Flame gases from 24 experimental fires were collected in canisters and analyzed using EPA method TO-14A for CO 2 , CO, H 2 , CH 4 , and C 2 to C 7 hydrocarbon gases. Condensed gas (tar) samples were collected and analyzed using GC/MS. Other light gases were measured using FTIR spectroscopy. Results from compositional data analysis suggest significant differences in (relative) concentration of compounds detected in the three regions of the flame. Statistical tests for differences in flame zones were performed using the canister data: Concentration of hydrocarbons relative to CO and CO 2 decreased from the persistent flame zone above the pyrolyzing needles through the intermittent flame region into the flame-free plume. This was likely due to both chemical reactions (oxidation) occurring in the flame as well as the introduction of air into the flame/plume by entrainment.

Biomass↗
DOE OSTI2022

Report of Geology from the T.R. McMillen #2 Well Drilled for CarbonSAFE Illinois - Macon County (Task 6)

This extensive report describes the sedimentology and sequence stratigraphy of the Mt Simon Sandstone, seismic reflection, Precambrian basement geochronology, petrophysical analyses, reservoir properties and petrographic characterization based on data collected during drilling and 2D seismic surveys conducted as part of CarbonSAFE Illinois - Macon County.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2024

EPCAPE-Dalhousie Field Campaign Report

This project supported the Eastern Pacific Cloud Aerosol Precipitation Experiment (EPCAPE), which aimed to characterize the extent, radiative properties, aerosol interactions, and precipitation of stratocumulus clouds in the Eastern Pacific coastal region of La Jolla, California. Given the frequent anthropogenic aerosols emitted into this region, characterization of this important coastal cloud region and the aerosol impact on the cloud characteristics will improve the understanding of aerosol indirect effects and its representation in global climate models. This specific project deployed the fog droplet monitor (FM-120, Droplet Measurement Technologies) at the Scripps Institution of Oceanography’s Mt. Soledad site from 16 February 2023 to 15 February 2024. This instrument measured droplet number size spectra between 2 and 50 microns, from which droplet number concentration, liquid water content, and effective diameter were calculated. These measurements will be used to characterize the seasonal variability of clouds at Mt. Soledad and investigate differences in cloud properties under regional polluted and clean marine conditions. The collected data will soon be posted as part of the digital collection for EPCAPE data hosted by the University of California, San Diego (Russell et al. 2023).

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Wabash CarbonSAFE: Detailed Site Characterization Plan, Task 11.0, Technical Report

Wabash CarbonSAFE established that commercial-scale CO 2 storage in the Potosi Dolomite –Maquoketa Group storage complex associated with the Wabash Valley Resources (WVR) plant site near Terre Haute, IN is highly feasible. The CarbonSAFE project team performed this evaluation through extensive data acquisition and analysis including 2D seismic reflection data, wireline logs, well testing, and core/cuttings from the Wabash #1 stratigraphic test well (now plugged and abandoned). This document summarizes work detailed in separate Wabash CarbonSAFE reports and consolidates the geologic characterization, well testing, and storage complex modeling results for the Mt. Simon Sandstone and Potosi Dolomite, two distinct reservoirs characterized at the Wabash CarbonSAFE project site. The report then presents recommendations for the next steps for site characterization, identifies data gaps for future activities, and provides an overall assessment of site potential.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2023

Mapping foliar photosynthetic capacity in sub-tropical and tropical forests with UAS-based imaging spectroscopy: Scaling from leaf to canopy

Accurate understanding of the variability in foliar physiological traits across landscapes is critical to improve parameterization and evaluation of terrestrial biosphere models (TBMs) that seek to represent the response of terrestrial ecosystems to a changing climate. Numerous studies suggest imaging spectroscopy can characterize foliar biochemical and morphological traits at the canopy scale, but there is only limited evidence for retrieving canopy photosynthetic capacity (e.g., maximum carboxylation rate, V c,max and maximum electron transport rate, J max ). Moreover, the effect of canopy structure within forest communities on scaling up spectra-trait relationships from leaf to canopy level is not well known. To advance the spectra-trait approach and enable the estimation of key traits using remote sensing, we collected imaging spectroscopy data from an Unoccupied Aerial System (UAS) platform over two forest sites in China (a subtropical forest in Mt. Dinghu and a tropical rainforest in Xishuangbanna). At these sites, we also collected ground measurements of leaf spectra and traits, including biochemical (leaf nitrogen, phosphorus, chlorophyll, and water content), morphological (leaf mass per area, LMA) and physiological (V c,max25 and J max25 ) traits (n=135 tree-crowns from 42 species across two sites). Using a partial least-squares regression (PLSR) approach, we built and tested spectra-trait models with repeated cross-validation. The spectral models developed with leaf spectra were directly transferred to canopy spectra to evaluate the effect of canopy structure. Here we further applied canopy spectral models to map these traits at individual tree-crown scale. The results demonstrate that (1) UAS-based canopy spectra can be used to estimate V c,max (R 2 =0.55, nRMSE=11.79%), Jmax (R 2 =0.54, nRMSE=12.34%), and five additional foliar traits (R 2 =0.38-0.60, nRMSE=10.11-13.56%) at the tree-crown scale with demonstrated generalizability across two sites; (2) canopy structure strongly affects the spectratrait relationships from leaf to canopy level, but the effects vary considerably across foliar traits and cannot be well captured by the 4SAIL canopy radiative transfer model. UAS-based imaging spectroscopy maps large variability in all foliar traits (including physiological traits) with spatially explicit information, reproducing the field-observed inter- and intra-specific variations. These results demonstrate the capability of using UAS-based imaging spectroscopy for characterizing the variability of foliar physiological traits at individual tree-crown scale over forest landscapes and highlight the similar generalizability but different biophysical mechanisms underlying spectra-trait relationships at leaf and canopy levels.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

FutureGen VSP

Processed SEGY files from the FutureGen2 project. Data includes 5 categories of OVSP data with 15 lines in each category (all in TWT). VSP data was processed from Sterling Seismic.

FutureGen2↗
DOE OSTI2024

Learning linear optical circuits with coherent states

We analyze the energy and training data requirements for supervised learning of an M-mode linear optical circuit by minimizing an empirical risk defined solely from the action of the circuit on coherent states. When the linear optical circuit acts non-trivially only on k < M unknown modes (i.e. a linear optical k-junta), we provide an energy-efficient, adaptive algorithm that identifies the junta set and learns the circuit. We compare two schemes for allocating a total energy, E, to the learning algorithm. In the first scheme, each of the T random training coherent states has energy E/T. In the second scheme, a single random MT-mode coherent state with energy E is partitioned into T training coherent states. The latter scheme exhibits a polynomial advantage in training data size sufficient for convergence of the empirical risk to the full risk due to concentration of measure on the $(2MT-1)$-sphere. Specifically, generalization bounds for both schemes are proven, which indicate that for ε-approximation of the full risk by the empirical risk with high probability, $O(E^{2/3}M^{2/3}/\epsilon^{2/3})$ training states are sufficient for the first scheme and $O(E^{1/3}M^{1/3}/\epsilon^{2/3})$ training states are sufficient for the second scheme.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2025

Characterizing the Oscillatory Properties of Bulk Electric Systems

This paper presents a process for characterizing the oscillatory dynamics of a large bulk power system. As a demonstration, the process is applied to the Western Interconnection of North America. Several complementary analysis approaches, both new and existing, are employed to provide a comprehensive understanding of the oscillatory properties of the system. Established modal analysis techniques based on ringdown and mode-meter algorithms are utilized. In addition, we derive and apply methods based on spectral correlation analysis to identify modal frequencies, distinguish between modes that are closely spaced in frequency, and determine locations at which the modes are observable. Critical interarea modes are identified and characterized using actual-system synchrophasor measurements taken over several years of operation in concert with industry-standard simulation models. This includes 145 hours of PMU data and two planning base cases.

42 ENGINEERING↗
DOE OSTI2025

CLEAP Project: OR-SAGE Analysis for MT, UT, and CO States

The OR-SAGE tool is designed to use industry-accepted practices in screening sites and then employ the proper array of data sources through the considerable computational capabilities of GIS technology available at ORNL. The tool was developed to screen the potential for NPP siting on a national and regional basis. However, because of the tool granularity, it is often focused specifically on the immediate area around user sites of interest. If data center siting parameters can be added to OR-SAGE, the ability to evaluate data center siting on a localized scale will be beneficial.1 More than 60 data sets have been collected and processed by ORNL to develop exclusionary, avoidance, and suitability criteria for screening sites for a variety of power generation types, including nuclear power plants. Available site evaluation parameters include population density, slope, seismic activity, proximity to cooling-water sources, proximity to hazard facilities, avoidance of protected lands and floodplains, susceptibility to landslide hazards, and many others. All siting parameters should be considered as flags to inform siting decisions and should not be used to rule in or rule out any NPP site. Once data center siting parameters are identified, appropriate data sets will be collected and processed. The OR-SAGE process is very versatile. Essentially, OR-SAGE is a visual, relational database. The database partitions the contiguous United States, a total of 720 million hectares (~1.8 billion acres), into 100-m by 100-m (1 hectare or ~2.5 acre) cells. The database is tracking just under 700 million individual land cells. Successive suitability criterion is applied to each cell in the database. User-specified thresholds can be applied to each siting parameter data layer. In this manner, a variety of scenarios can be quickly and thoroughly evaluated. Data can be added and/or revised within OR-SAGE to address user interests. Siting security assessment capability is currently being added to OR-SAGE. Security is expected to be of concern at data centers whether it is collocated with a nuclear power generating technology or not. If data center is collocated with a nuclear power generating source, the security threat attractiveness level of both will likely increase. It will be of additional benefit if a potential data center site is also assessed for security vulnerability.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2026

Yield Estimates of three Historical Atmospheric Nuclear Explosions at Lop Nor, from Reduced Order Models of Regionally Recorded Rayleigh Waveforms and One Seismic Station: A Brief Communication

We use a reduced order model (ROM) for Rayleigh waveforms sourced by large atmospheric explosions along with data collected from a single seismic station (TLG) to estimate the yields of three atmospheric nuclear tests with order-megaton (MT) yields. These historical tests were conducted by China between 1973 and 1980 (CHIC 15, CHIC 16, and CHIC 26). We use our ROM to estimate yields of 2.34 MT (CHIC 15), 0.51 MT (CHIC 16), and 1.15 (CHIC 26) in the 20.5 s period band that are consistent with publicly accepted values of 3 MT (CHIC 15), 0.50 MT (CHIC 16), and 0.730 MT (CHIC 26).

58 GEOSCIENCES↗
DOE OSTI2026

Local Tractor Activity at S2 (Mt. Airy) Site

This dataset documents local tractor activity at the S2 (Mt. Airy) site during CoURAGE. It identifies periods where local tractor activity impacted aerosol measurements using both PM10/PM2.5 ratios and ARM camera data for visual confirmation of tractor. Data flags are as follows: 1 = confirmed no local tractor influence on aerosol measurements 2 = one data indicator is present (extreme PM10/PM2.5 ratio OR visual confirmation of tractor sighting), but not both 3 = both data indicators confirm local tractor influence on aerosol 0 = missing data, no determination possible

Tractor Activity using ARM camera photos and PM10/↗
DOE OSTI2021

Mass Balance Accounting for CO2 Storage with Enhanced Oil Recovery in Northern Michigan

Battelle’s MRCSP Phase III monitoring efforts began on February 3, 2013, with an overarching goal of monitoring at least 1 million metric tons (MT) of net CO2 stored within Core Energy’s EOR complex. For the purposes of this report, most of the mass balance accounting data is shown through September 30, 2019, a period of 6 years, 10 months..

Bagley↗
DOE OSTI2022

Magnetotelluric Investigations of the Kilauea Volcano, Hawaii

In 2002 and 2003 a collaborative effort was undertaken between Lawrence Berkeley National Laboratory, Sandia National Laboratories, the U.S. Geological Survey (USGS) Menlo Park, the USGS Hawaiian Volcano Observatory, and Electromagnetic Instruments Inc. to study the Kilauea volcano in Hawaii using the magnetotelluric (MT) technique. The work was motivated by a desire to improve understanding of the magma reservoirs and conduits within Kilauea and the East and Southwest Rift zones, which has implications for understanding Kilauea's plumbing system. An improved understanding of the rift zones has implications in understanding large-scale landslides that are generated in the Hilina Slump, which produce significant impacts on coastal communities. Up to eight stations operated simultaneously, with multiple remote reference sites, and data were processed using multi-station robust processing techniques. Data was acquired at 70 sites over the Southwest and East rift zones. Good to excellent quality data were obtained even in the harshest conditions, such as those encountered on the fresh lava flows of the East Rift Zone, where electrical contact resistances are on the order of 100 kΩ. A three-dimensional (3D) MT model study was done to guide interpretation of the observed MT measurements. Synthetic modeling demonstrates that conductive bodies in the upper 3 km can be spatially resolved where MT station sampling is good. Resistivity anomalies in the 3D inversions have a high degree of spatial correlation with previously published seismic velocity anomalies beneath Kilauea. Melt fractions between 0.096 and 0.117 are calculated for the Kilauea and Pu'u'ō'ō low resistivity anomalies, respectively.

58 GEOSCIENCES↗
DOE OSTI2023

Defense against phytopathogens relies on efficient antimicrobial protein secretion mediated by the microtubule-binding protein TGNap1

Plant immunity depends on the secretion of antimicrobial proteins, which occurs through yet-largely unknown mechanisms. The trans-Golgi network (TGN), a hub for intracellular and extracellular trafficking pathways, and the cytoskeleton, which is required for antimicrobial protein secretion, are emerging as pathogen targets to dampen plant immunity. In this work, we demonstrate that tgnap1-2, a loss-of-function mutant of Arabidopsis TGNap1, a TGN-associated and microtubule (MT)-binding protein, is susceptible to Pseudomonas syringae (Pst DC3000). Pst DC3000 infected tgnap1-2 is capable of mobilizing defense pathways, accumulating salicylic acid (SA), and expressing antimicrobial proteins. The susceptibility of tgnap1-2 is due to a failure to efficiently transport antimicrobial proteins to the apoplast in a partially MT-dependent pathway but independent from SA and is additive to the pathogen-antagonizing MIN7, a TGN-associated ARF-GEF protein. Therefore, our data demonstrate that plant immunity relies on TGNap1 for secretion of antimicrobial proteins, and that TGNap1 is a key immunity element that functionally links secretion and cytoskeleton in SA-independent pathogen responses.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2021

Utah FORGE 2020-2021 Geothermal Energy/EGS Survey and Results

The Utah FORGE project collaborated with the University of Utahs Department of Communication on a Capstone course during Fall Semester 2020. The course created a survey to gauge the general populations knowledge of geothermal energy and Enhanced Geothermal Systems (EGS). The survey was distributed through Qualtrics, an experience management company, in late 2020 and early 2021 to respondents in 11 western states (AZ, CA, CO, ID, MT, NM, NV, OR, UT, WA, WY). Approximately 1,000 responses were received. The Code Book (the consent form and the questions themselves) and the raw data results in a spreadsheet are included in the data resources.

15 GEOTHERMAL ENERGY↗
DOE OSTI2026

Illinois Storage Corridor, CarbonSAFE Phase III: UIC Class VI Permitting Plan

The Illinois Storage Corridor (ISC) project evaluated two distinct sites to determine the feasibility of commercial-scale CO₂ storage at each. The project leveraged the region's exceptional geological characteristics, particularly the well-characterized Cambro-Ordovician Storage Complex, to enable permanent geological storage of more than 50 million tonnes of CO₂ over 30 years. The two storage sites are located at One Earth Energy (OEE) facility in northcentral Illinois and Prairie State Generating Company (PSGC) in southcentral Illinois. Once operational, these facilities will combine to capture and store more than 6.5 million tonnes of CO₂ per year, positioning the ISC among the largest carbon storage regions globally. Preliminary homogeneous dynamic modeling based on regional and site-specific reservoir characteristics indicates promising injection capabilities at both locations. For the OEE site, modeling predicts a maximum allowable injection rate of 3.7 MTPA, with a baseline scenario of 1.7 MTPA over 30 years producing a CO₂ plume radius of 1.4 miles at end of injection. For the PSGC site, incorporating recent well data, modeling indicates a single-well maximum injection rate of 2.1 MTPA, with a plume radius of 4.2 miles at end of injection for the 60 MT over 30 years scenario. The primary objective of this CarbonSAFE Phase III project is to develop and submit Class VI Underground Injection Control (UIC) permit applications to the U.S. Environmental Protection Agency Region 5. The permitting plan outlines comprehensive site characterization, Area of Review delineation, monitoring programs, well construction designs, financial responsibility provisions, and post-injection site care procedures necessary to demonstrate safe, permanent CO₂ storage protective of underground sources of drinking water. Three UIC Class VI permit applications for the OEE site were submitted to EPA in October 2022 and are progressing through technical review, with final permit decision projected by June 2026. Through five rounds of Requests for Additional Information and responses, the applications have been refined to address computational modeling, area of review delineation, well integrity, monitoring protocols, and financial assurance requirements. For the PSGC site, finalized characterization and permitting documentation was delivered directly to the facility in July 2023 due to business constraints precluding formal federal regulatory submission. This comprehensive permitting effort builds upon extensive prior subsurface evaluations and demonstration projects that have confirmed the feasibility of widespread commercial-scale carbon storage in the region.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2025

NLR HPC Eagle GPU Node Metrics

Ganglia node metrics and iLO (Integrated Lights Out) power data captured from six representative Eagle GPU nodes The Eagle HPC operated at NLR from 2019 through 2024. Eagle was a 2,000-node, 8-petaflop system. This dataset is a representative sample of metrics for 6 of the GPU nodes. Each GPU node contained 2 CPUs and 2 GPUs. Data provided in compressed CSV format. Ganglia and iLO Power Time Series Fields ts: Timestamp dv: Device / Node - Rack and Unit - r103u17 == r(ack)103u(nit)17 mt: Metric (only present for Ganglia) vl: Value - Value in watts for iLO power (instantaneous value at sampling time) or specified Ganglia metric below Ganglia Metrics Metric name -- Metric description -- Unit cpu_aidle -- Percent of time since boot idle CPU -- Percent cpu_idle -- Percent CPU idle -- Percent cpu_nice -- Percent CPU nice -- Percent cpu_speed -- Speed in MHz of CPU -- MHz cpu_user -- Percent CPU user -- Percent cpu_wio -- The percentage of CPU Wait I/O -- Percent gpu0_bar1_memory -- Used GPU bar1 memory -- MB gpu0_decoder_util -- GPU decoder utilization -- Percent gpu0_ecc_db_error -- Total ECC error counts for the GPU -- Number gpu0_encoder_util -- GPU encoder utilization -- Percent gpu0_fan -- Fan speed -- RPM gpu0_fb_memory -- Used GPU framebuffer memory -- MB gpu0_graphics_clock_report -- Current clock speeds for the device -- MHz gpu0_mem_total -- Memory total -- MB gpu0_mem_util -- Memory utilization -- Percent gpu0_power_usage_report -- Power usage report -- Watts gpu0_temp -- GPU 1 temperature -- Celsius gpu1_bar1_memory -- Used GPU bar1 memory -- MB gpu1_decoder_util -- GPU decoder utilization -- Percent gpu1_ecc_db_error -- Total ECC error counts for the GPU -- Number gpu1_encoder_util -- GPU encoder utilization -- Percent gpu1_fan -- Fan speed -- RPM gpu1_fb_memory -- Used GPU framebuffer memory -- MB gpu1_graphics_clock_report -- Current clock speeds for the GPU -- MHz gpu1_mem_total -- Memory total -- MB gpu1_mem_util -- Memory utilization -- MB gpu1_power_usage_report -- Power usage report -- Watts gpu1_temp -- GPU 1 temperature -- Celsius ipmi_cpu1_temp -- CPU 1 temperature -- Celsius ipmi_cpu2_temp -- CPU 2 temperature -- Celsius ipmi_inlet_ambient_temp -- Temperature measured at intake -- Celsius ipmi_vr_p1_temp -- CPU 1 voltage regulator temperature -- Celsius ipmi_vr_p2_temp -- CPU 2 voltage regulator temperature -- Celsius mem_buffers -- Amount of buffered memory -- Bytes mem_cached -- Amount of cached memory -- Bytes mem_free -- Amount of available memory -- Bytes mem_shared -- Amount of shared memory -- Bytes mem_total -- Amount of available memory -- Bytes

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2025

Updates on MURAVES Project at Mt. Vesuvius

The MUon RAdiography of VESuvius (MURAVES) project aims to employ muography imaging techniques to investigate the internal structure of the summit of Mount Vesuvius, an active volcano located near Naples, Italy. This paper reports recent advancements in data analysis and simulation tools that significantly improve the quality and reliability of the experiment’s results. A new track selection method, referred to as the Golden Selection, has been developed to identify high-quality muon tracks by applying an improved χ 2 -based criterion. This method enhances the signal-to-background ratio and improves the resolution of the resulting muographic images. Moreover, the simulation framework has been upgraded through the integration of the MULDER (MUon simuLation for DEnsity Reconstruction) library, which consolidates the functionalities of previously used libraries into a single, unified platform. MULDER enables efficient and accurate modeling of muon flux variations induced by topographical features. A good agreement is observed between the simulated and measured muon flux maps, validating the effectiveness of the new analysis and simulation approaches.

Cosmic rays↗