Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MECHANICAL PROPERTY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Matrix density effects on the mechanical properties of SiC fiber-reinforced silicon nitride matrix properties

The room temperature mechanical properties were measured for SiC fiber reinforced reaction-bonded silicon nitride composites (SiC/RBSN) of different densities. The composites consisted of approx. 30 vol percent uniaxially aligned 142 micron diameter SiC fibers (Textron SCS-6) in a reaction-bonded Si3N4 matrix. The composite density was varied by changing the consolidation pressure during RBSN processing and by hot isostatically pressing the SiC/RBSN composites. Results indicate that as the consolidation pressure was increased from 27 to 138 MPa, the average pore size of the nitrided composites decreased from 0.04 to 0.02 microns and the composite density increased from 2.07 to 2.45 gm/cc. Nonetheless, these improvements resulted in only small increases in the first matrix cracking stress, primary elastic modulus, and ultimate tensile strength values of the composites. In contrast, HIP consolidation of SiC/RBSN resulted in a fully dense material whose first matrix cracking stress and elastic modulus were approx. 15 and 50 percent higher, respectively, and ultimate tensile strength values were approx. 40 percent lower than those for unHIPed SiC/RBSN composites. The modulus behavior for all specimens can be explained by simple rule-of-mixture theory. Also, the loss in ultimate strength for the HIPed composites appears to be related to a degradation in fiber strength at the HIP temperature. However, the density effect on matrix fracture strength was much less than would be expected based on typical monolithic Si3N4 behavior, suggesting that composite theory is indeed operating. Possible practical implications of these observations are discussed.

Bhatt, Ramakrishna T.↗
NASA NTRSDate not supplied

Multi-Scale Analysis of Effective Mechanical Properties of Porous 3D Woven Composite Materials

This work aims to compute and analyze the mechanical properties of 3D woven composite materials that share the same yarn structure but differ in their matrix porosity and yarn's fiber volume fraction. Assuming linear elastic behavior, NASA's PuMA software was used to characterize the different composites from their constituents' data, averaging their elastic properties in three main directions to obtain their effective orthotropic mechanical properties. This was performed in three steps: firstly, the porous matrix phase was analyzed at the micro-scale; then, these results were used, along with the mechanical properties of the fibers, to model the yarns at the meso-scale; finally, results from the constituents were homogenized and used to model the mechanical behavior of the unit cell at the macro-scale. The 3D woven composite materials selected for this study are made of a mixture of phenolic resin with porosity values between 0 and 0.6, and infiltrated carbon fiber yarns with fiber volume fractions between 0.5 and 0.8. Results from this study show the effect of different matrix porosities and fiber volume fractions on the macro-scale mechanical properties, and were validated through theoretical and semi-empirical expressions found in the literature.

3D woven materials↗
NASA NTRS1982

Mechanical properties of low tantalum alloys

The mechanical property behavior of equiaxed cast B-1900 + Hf alloy as a function of tantalum content was studied. Tensile and stress rupture characterization was conducted on cast to size test bars containing tantalum at the 4.3% (standard level), 2.2% and 0% levels. Casting parameters were selected to duplicate conditions used to prepare test specimens for master metal heat qualification. The mechanical property results as well as results of microstructural/phase analysis of failed test bars are presented.

Kortovich, C. S.↗
DOE OSTI2024

ElasTool v3.0: Efficient computational and visualization toolkit for elastic and mechanical properties of materials

Efficient computation and visualization of elastic and mechanical properties are crucial in the selection of materials and the design of new materials. Here, the ElasTool v3.0 toolkit marks a significant advancement in the computational analysis and visualization of elastic and mechanical properties of materials, essential in material selection and design. This enhanced version extends beyond standard calculations like elastic tensor, Young's modulus, bulk modulus, and Poisson's ratio. It introduces capabilities for computing minimum thermal conductivity, linear compressibility, rendering the Christoffel equation, and elastic energy density. Notably, it integrates advanced visualization tools, including compatibility with Plotly and Elate web platforms for interactive web-based property exploration. A key feature of ElasTool v3.0 is the implementation of second-order elastic constants (SOECs) for tubular 2D-based nanostructures and nanotubes. Leveraging high-efficiency strain-matrix sets (OHESS), the toolkit now facilitates efficient computation of elastic constants and mechanical properties at both zero and finite temperatures for 1D, 2D, and 3D dimensions. ElasTool is openly accessible on GitHub: https://github.com/gmp007/elastool.

1D, 2D, 3D, and tubular 2D nanostructure and nanot↗
NASA NTRS1979

Mechanical property characterization of intraply hybrid composites

An investigation of the mechanical properties of intraply hybrids made from graphite fiber/epoxy matrix hybridized with secondary S-glass or Kevlar 49 fiber composites is presented. The specimen stress-strain behavior was determined, showing that mechanical properties of intraply hybrid composites can be measured with available methods such as the ten-degree off-axis test for intralaminar shear, and conventional tests for tensile, flexure, and Izod impact properties. The results also showed that combinations of high modulus graphite/S-glass/epoxy matrix composites exist which yield intraply hybrid laminates with the best 'balanced' properties, and that the translation efficiency of mechanical properties from the constituent composites to intraply hybrids may be assessed with a simple equation.

Chamis, C. C.↗
DOE OSTI2019

Effect of Process Parameters on the Mechanical Properties of Hastelloy X Alloy Fabricated by Selective Laser Melting

Mechanical properties of Hastelloy X alloys fabricated by selective laser melting were investigated and compared with the wrought counterpart. Nano-inclusions (Mo-rich carbides) distributed at the sub-grain boundaries in the selective laser-melted (SLMed) Hastelloy X alloy, whereas micron-scale precipitations existed in the wrought counterpart. The molten pool boundaries widely existed in the SLMed substrate, which acted as an initial site for crack and led to poor plasticity. However, the ultimate tensile strength values of the SLMed Hastelloy X alloys were around 910 MPa and much higher than the wrought counterpart (~ 750 MPa), which was mainly ascribed to the high-density dislocations enriched at the sub-grain boundaries. Process parameter effects on the mechanical properties were also delineated in this work, and the volumetric energy density for the best mechanical properties of the SLMed Hastelloy X alloy was in the range from 140 to 170 J/mm{sup 3}.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Elevated temperature mechanical properties of Inconel 617 surface oxide using nanoindentation

Inconel 617 is a principal candidate material for helium gas cooled very-high-temperature reactors with outlet temperatures of 700–950 °C. Recent findings showed that this alloy develops unique surface oxide layers especially at high temperature (HT) helium environment with distinctive wear, friction and contact properties. This study investigates the elevated temperature mechanical properties of Inconel 617 top surface layers aged in HT helium environment. Nanoindentation technique is used to obtain load-displacement graphs of the alloy top surface oxide in temperatures ranging from 25 °C up to 600 °C. In addition, using finite element analysis along with an iterative regression technique, a semi-numerical method is developed to further measure and quantify the material parameters and, in particular, time-independent and creep characteristics of the oxide. Although Young's modulus of the oxide is found to be relatively close to the bulk for the tested temperatures, the yield strength and hardness, in comparison to the bulk material, increase significantly as the material is oxidized after aging. The oxide exhibits significant softening as the temperature increases to 600 °C. Unlike the bulk material, diffusion through the grains is found to be the dominant creep mechanism for the oxide. Considerable difference between the mechanical properties of the oxide and the bulk material shows the need for accurate measurements of near surface mechanical properties, if reliable predictive contact and tribological models are sought at elevated temperatures.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Impact of hydrogenation on the stability and mechanical properties of amorphous boron nitride

Abstract Interconnect materials with ultralow dielectric constant, and good thermal and mechanical properties are crucial for the further miniaturization of electronic devices. Recently, it has been demonstrated that ultrathin amorphous boron nitride (aBN) films have a very low dielectric constant, high density (above 2.1 g cm −3 ), high thermal stability, and mechanical properties. The excellent properties of aBN derive from the nature and degree of disorder, which can be controlled at fabrication, allowing tuning of the physical properties for desired applications. Here, we report an improvement in the stability and mechanical properties of aBN upon hydrogen doping. With the introduction of a Gaussian approximation potential for atomistic simulations, we investigate the changing morphology of aBN with varying H doping concentrations. We found that for 8 at% of H doping, the concentration ofsp 3 -hybridized atoms reaches to a maximum which leads to an improvement of thermal stability and mechanical properties by 20%. These results will be a guideline for experimentalists and process engineers to tune the growth conditions of aBN films for numerous applications.

Materials Science↗
DOE OSTI2021

Comparison of the Mechanical Properties of a Conjugated Polymer Deposited Using Spin Coating, Interfacial Spreading, Solution Shearing, and Spray Coating

The mechanical properties of π-conjugated (semiconducting) polymers are a key determinant of the stability and manufacturability of devices envisioned for applications in energy and healthcare. These properties—including modulus, extensibility, toughness, and strength—are influenced by the morphology of the solid film, which depends on the method of processing. To date, the majority of work done on the mechanical properties of semiconducting polymers has been performed on films deposited by spin coating, a process not amenable to the manufacturing of large-area films. Here, we compare the mechanical properties of thin films of regioregular poly(3-heptylthiophene) (P3HpT) produced by three scalable deposition processes—interfacial spreading, solution shearing, and spray coating—and spin coating (as a reference). Our results lead to four principal conclusions. (1) Spray-coated films have poor mechanical robustness due to defects and inhomogeneous thickness. (2) Sheared films show the highest modulus, strength, and toughness, likely resulting from a decrease in free volume. (3) Interfacially spread films show a lower modulus but greater fracture strain than spin-coated films. (4) The trends observed in the tensile behavior of films cast using different deposition processes held true for both P3HpT and poly(3-butylthiophene) (P3BT), an analogue with a higher glass transition temperature. Grazing incidence X-ray diffraction and ultraviolet–visible spectroscopy reveal many notable differences in the solid structures of P3HpT films generated by all four processes. Herein, while these morphological differences provide possible explanations for differences in the electronic properties (hole mobility), we find that the mechanical properties of the film are dominated by the free volume and surface topography. In field-effect transistors, spread films had mobilities more than 1 magnitude greater than any other films, likely due to a relatively high proportion of edge-on texturing and long coherence length in the crystalline domains. Overall, spread films offer the best combination of deformability and charge-transport properties.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Effect of Solution Heating Rate on Quasi-static and Dynamic Mechanical Properties of Al-Mg-Si-Cu Alloy

The effect of solution heating rate on quasi-static and dynamic mechanical properties of Al-Mg-Si-Cu alloy in bake hardening state was investigated through mechanical properties, microstructure and fracture morphology characterization in the present study. The results show that solution heating rate has a strong influence on microstructure, quasi-static and dynamic mechanical properties. As solution heating rate rises, the grain microstructure transforms from the elongated grains to equiaxed grains and the fraction of low-angle grain boundaries (LAGBs) also decreases. Moreover, the equivalent average grain size first decreases, and then increases. The relationship between solution heating rate and mechanical property is monotonic, not depending on strain rate. As solution heating rate rises, the yield strength, ultimate tensile strength and elongation decrease. In contrast to quasi-static loading, dynamic loading always tends to improve strengths and elongation. In addition, compared with the quasi-static tensile specimens, the dynamic tensile specimens possess a larger number of dislocations. Regardless of strain rate and solution heating rate, all the tensile specimens exhibit the ductile fracture mode. As solution rate rises, the dimples decrease and become shallow gradually. The dimples in dynamic fracture zone are larger and deeper than those in the quasi-static fracture zone.

36 MATERIALS SCIENCE↗
NASA NTRS1992

Sintering time and atmosphere influences on the microstructure and mechanical properties of tungsten heavy alloys

The present paper traces the microstructure and mechanical property variations vs sintering time under conditions where the atmosphere was adjusted to suppress pore generation. Attention is given to tracing the mechanical property links to the grain size under optimized sintering conditions. The optimal cycle is used to sinter two heavy alloy compositions (88 and 95 wt pct W) for times up to 600 minutes at 1480 C. The 88-pct-W samples slumped, but the 95-pct-W samples were fully densified and suitable for tensile testing. At long sintering times, the tungsten grains flattened and the tungsten contiguity decreased, indicating a transition to low-energy configurations for the solid-liquid interfaces. The cube of the mean grain size varied linearly with the isothermal sintering time. This allowed the determination of grain size effects on mechanical properties, showing a decreasing yield strength with increasing time in agreement with the Hall-Petch behavior. The tensile strength and elongation were highest for sintering times from 30 to 90 min, reflecting a minimum in the residual porosity.

German, R. M.↗
NASA NTRSDate not supplied

Multi-Scale Analysis of Effective Mechanical Properties of 3D Woven Composite Materials

This work aims to compute and analyze the mechanical properties of 3D woven composite materials that share the same yarn structure but differ in their matrix porosity and fiber volume fraction. Assuming linear elastic behavior, the software PuMA, developed at NASA, was used to characterize the different composites from their constituents' data averaging their elastic properties in three main directions to obtain their effective orthotropic mechanical properties. This was performed in three steps: firstly, the different phases (yarns/matrix) were analyzed as anisotropic materials separately at the micro-scale; then, the results from these analyses were homogenized and used to obtain the anisotropic elasticity tensor at the meso-scale for the different woven materials; and finally, assuming orthotropic mechanical behavior for the unit cell the mechanical properties were obtained at the macro-scale. The 3D woven composite materials selected for this study are made of phenolic resin with porosity values between 0 and 0.6, and resin infiltrated carbon fiber with volume fractions between 0.5 and 0.9 for the yarns. Results from PuMA were validated with external FEA simulations for the non-porous 3D woven material with a fiber volume fraction of 0.9 in the yarns. Results will be included in the final paper after completing the study detailed in Section II.

Sergio Fraile Izquierdo↗
DOE OSTI2025

Temperature-Dependent Mechanical Properties of Ni-Based Concentrated Alloys: Insights from First-Principles Calculations

The present work focuses on predicting temperature-dependent mechanical properties of Ni-based concentrated alloys Ni 18 Cr 10 Co 10 Fe 6 M 4 (abbreviated by X 44 M 4 , with M = Al, V, Mn, Fe, Nb, Mo, and W) using density functional theory (DFT). These predictions are based on shear (plastic) and elastic deformations, utilizing the special quasirandom structure (SQS), the phonon-based quasiharmonic approach (QHA), and the quasistatic approach. The resulting properties include coefficient of thermal expansion via QHA, ideal shear strength (τ IS ), and stable and unstable stacking fault energies (γ SF and γ US ) through pure alias shear deformation, and elastic constants (c ij ), bulk modulus (B 0 ), and shear modules (G 0 ) via elastic deformation. Notably, predicting accurate γ SF is challenging due to uncertainties that can exceed the γ SF values. τ IS and γ US exhibit a strong linear relationship, enabling the accurate prediction of γ US based on the precisely determined τ IS . All mechanical properties of X 44 M 4 decrease with increasing temperature, except for some γ SF cases such as X 44 M 4 with M = V, Mn, Fe, Mo, and W. Among the X 44 M 4 alloys, X 44 Nb 4 exhibits the lowest τ IS , γ US , and G 0 values, and the highest B 0 /G 0 ratio, while X 44 Mn 4 has the lowest B 0 and B 0 /G 0 ratio. We found that volume is a crucial descriptor for understanding and modeling mechanical properties (except B0 and maybe also γ SF ) affected by alloying elements and temperature. Ni-based dilute alloys (e.g., Ni 11 M 1 and Ni 31 M 1 ) and concentrated alloys (e.g., X 44 M 4 ) show similar trends in mechanical properties influenced by alloying elements and temperature, simplifying the analysis and design of Ni-based alloys.

Elastic properties↗
NASA NTRS1981

Static and yawed-rolling mechanical properties of two type 7 aircraft tires

Selected mechanical properties of 18 x 5.5 and 49 x 17 size, type 7 aircraft tires were evaluated. The tires were subjected to pure vertical loads and to combined vertical and lateral loads under both static and rolling conditions. Parameters for the static tests consisted of tire load in the vertical and lateral directions, and parameters for the rolling tests included tire vertical load, yaw angle, and ground speed. Effects of each of these parameters on the measured tire characteristics are discussed and, where possible, compared with previous work. Results indicate that dynamic tire properties under investigation were generally insensitive to speed variations and therefore tend to support the conclusion that many tire dynamic characteristics can be obtained from static and low speed rolling tests. Furthermore, many of the tire mechanical properties are in good agreement with empirical predictions based on earlier research.

Tanner, J. A.↗
DOE OSTI2020

Can Polyelectrolyte Mechanical Properties be Directly Modulated by an Electric Field? A Molecular Dynamics Study

Multifunctionality in polymers facilitates their application in emerging technologies. Electrical fields are a preferred stimulus because of the speed and ease of application to bulk polymers. While a wide range of electrically triggered actuators are developed, and electrically controlled adhesion between gels is demonstrated, modification of bulk mechanical properties via electrical stimuli remains elusive. Polymers with covalently incorporated ionic charge (polyelectrolytes) should be well suited to achieving this goal since the mechanical properties depend on electrostatic interactions and these charges are intrinsically susceptible to electric fields. Molecular dynamics simulations are utilized here to investigate whether electric fields can modulate the mechanical properties of polyelectrolytes and to understand the governing mechanisms. Mechanical property modulation by electric field is found to be sensitive to the charge distribution—charges must be tightly attached to the polymer backbone, and responsivity is greater if a single backbone contains both positive and negative charges. The dominant mechanisms are reorientation and stretching of the polymer chains, which also elongate the ionic clusters to maintain strong electrostatic interactions throughout deformation. Furthermore, these insights are critical for future experimental realization of polymers with electric field regulated mechanical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Molecular scale insight of pore morphology relation with mechanical properties of amorphous silica using ReaxFF

Porous materials are typically heterogeneous and they contain large variations of micro-/nano-pore structures, causing complicated behaviors. In continuum models, most mechanical properties of porous materials are estimated based on porosity, while the variations of micro/nano structures are ignored. That could be problematic as the microscopic heterogeneity may affect the mechanical response of porous materials. Thus, understanding micro/nano heterogeneity impact has been the focus in many scientific and engineering subjects. In the present study, we investigated the effect of nanopore structure (including pore shape and orientation) as well as porosity on mechanical properties of amorphous silica (a-SiO 2 ). The pore sizes in our simulations are comparable to the corresponding ones observed in a-SiO 2 based materials. We found that the existing of nanopores strongly influences Young’s modulus (E) and critical energy release rate (G IC ). These properties decrease with increasing porosity. Importantly, the impact of nanopores was characterized by structural parameters of porous materials. In addition to dependency on porosity, Young’s modulus also was found to vary as a function of potential energy per atom, which highly depends on nanopore shape. Furthermore, critical energy release rate was found to increase with increasing ligament length (also known as pore wall thickness). Finally, the results highlighted the importance of nanopore structures, which must be taken into account when studying fracture mechanisms in porous materials. Based on our findings, it was proposed that mechanical properties of porous materials can be controlled by nano-engineering pore structures.

36 MATERIALS SCIENCE↗