Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Lithiation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

High performance porous Si anode enabled by an organic-solvent assisted etching process

Silicon (Si) is a promising anode for the next generation of lithium-ion batteries, but its large volume changes (~300 %) during cycling hindered its practical applications. One method to improve its stability is to etch micron sized Si/SiO 2 particles to form porous Si (p-Si) and accommodate volume changes internally. However, the conventional HF etching method generates excess gas/heat and is difficult to scale up. Herein, we developed an organic-solvent-assisted HF etching process (O-HF) using a mixture of benzene and saturated HF aqueous solution. The organic solvent can be preferentially absorbed on the surface of Si/SiO 2 powder so etching rate of SiO 2 can be controlled to avoid rapid gas/heat generation. This method can also prevent over-etching of Si by minimizing direct contact/react between water and newly exposed Si. Si||NMC622 cells using carbon coated p-Si particles prepared by optimized O-HF etching process demonstrate a capacity retention of 82.0 % after 500 cycles, which is much better than those prepared by conventional HF etching (73.7 %). The thickness of Si anode increases only ~10 % during the initial lithiation, which is comparable with those of graphite anode. In conclusion, the O-HF etching strategy developed in this work can also be applied to the etching of a broad range of materials.

HF etching↗
DOE OSTI2026

Influence of aluminum source and Ni/Al ratio in a batch stirred tank reactor on the structure, morphology, and electrochemical performance of Ni-rich NMA cathodes

Here, the structural, morphological, and electrochemical performance of Ni-rich LiNi 0.9 Mn 0.05 Al 0.05 O 2 (955NMA) and LiNi 0.85 Mn 0.05 Al 0.1 O 2 (85,510) cathodes strongly depends on the properties of their hydroxide precursors. Ni-Mn-Al hydroxide precursors were synthesized through controlled co-precipitation in a batch stirred tank reactor, where pH, reaction time, metal-ion feed rate, aluminum source, and aluminum concentration were systematically varied to tailor particle morphology, phase composition, and dopant distribution. Two aluminum sources, aluminum nitrate and sodium aluminate produced two distinct hydroxide precursors NMA(OH) 2 -1 and NMA(OH) 2 -2, which were lithiated to form LiNMA1 (Li 0.992 [Ni 0.905 Mn 0.049 Al 0.046 ]O 2 ) and LiNMA2 (Li 0.990 [Ni 0.850 Mn 0.047 Al 0.103 ]O 2 ). Structural and compositional analyses revealed that aluminum incorporation and phase formation in Ni–Mn–Al hydroxides are governed by local supersaturation and interfacial growth kinetics. Rapid dilute aluminum addition produced aluminum-free β-phase hydroxides, intermediate conditions generated mixed α/β phases, whereas slow concentrated dosing enabled uniform aluminum incorporation and stabilization of the β-phase structure. LiNMA1 delivers a high initial discharge capacity of 223 mAhg −1 but significant capacity fading with 67% retention after 100 cycles, associated with structural instability. In contrast, LiNMA2 delivers a lower initial capacity 172 mAhg −1 yet excellent cycling stability 91% retention, attributed to improved TM–O framework stability and reduced cation disorder.

Capacity↗
DOE OSTI2026

pCAM precursor produced from electroextraction technology and its application in synthesis of NMC 811 cathode material

The synthesis and characterization of LiNi 0.8 Co 0.1 Mn 0.1 O 2 (LNMC811) cathodes produced from recycled hydroxide precursors obtained from spent lithium-ion batteries is evaluated. Two precursor batches (Sample 1 and Sample 2) are prepared using modified recycling processes to examine how residual impurities and processing conditions influence the properties of the regenerated materials. Structural and compositional characterization by X-ray diffraction, ICP and SEM shows that the recycled precursors exhibit layered hydroxide structures containing both α Ni(OH) 2 and β Ni(OH) 2 phases. Trace impurities including sodium, boron, and aluminum are detected and partially mitigated during processing, with boron found to play a beneficial role in electrochemical behavior. Following lithiation with lithium carbonate and lithium hydroxide at 800 °C under an oxygen rich atmosphere, the resulting LNMC811 materials show electrochemical performance comparable to conventionally synthesized cathodes. Sample 2, which contains higher boron levels and improved cation ordering, delivers an initial discharge capacity of 174 mAh g -1 and retains more than 93 percent of its capacity after 50 cycles. The stable cycling behavior and structural integrity of these materials demonstrate that recycled precursors can be converted into high performance layered cathodes and support recycling as a practical and sustainable route for lithium-ion battery manufacturing.

25 ENERGY STORAGE↗
DOE OSTI2025

Effect of Annealing on Direct Recycled NMC Cathodes

A substantial number of electric vehicle batteries are poised to reach end-of-life conditions in the next decade. Direct recycling has advantages over typical recycling processes because it preserves the chemical structure of the material. One key step of direct recycling materials like nickel manganese cobalt oxide (NMC) cathodes is relithiation, which includes replacing the depleted lithium inventory in the cathode and annealing the material to fix crystallographic degradation. This work uses multiple characterization techniques (synchrotron X-ray diffraction, Ni X-ray absorption near edge structure, scanning transmission electron microscopy) to understand the lithiation mechanism of degraded and chemically relithiated NMC 622. Despite the necessary reconstruction after relithiation being limited to the surface of the degraded NMC 622, a high annealing temperature of 720 °C is still necessary to restore the NMC 622 structure back to pristine condition after relithiation. This work also finds that treating degraded NMC 622 with an annealing step is sufficient to restore key electrochemical and structural properties, other essential features of pristine NMC 622 material such as particle porosity and morphology are largely unaffected. Understanding the effect of this annealing step has important implications on defining the degree of success of any given direct recycling strategy.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Automatic Generation of Chemical Mechanisms for Electrochemical Systems: Solid Electrolyte Interphase Formation in Lithium Batteries

Electrolytes in many lithium ion batteries decompose at the low potentials near the anode. The decomposition products form a layer termed the solid electrolyte interphase (SEI). The composition and growth of the SEI layer significantly affect both the capacity fade and safety of lithium ion batteries. However, SEI formation and growth kinetics are not well understood. In this work, we present an extension of the Reaction Mechanism Generator (RMG) software to automatically generate mechanisms for SEI formation. We extend RMG’s solvation correction framework to account for kinetic solvent effects and demonstrate the accuracy of our technique. We calculate thermochemical parameters for 252 species and rate coefficients for 69 reactions, most with associated solvation corrections. This and additional quantum chemistry data are used to extend RMG’s thermodynamic group additivity and solute parameter estimation schemes to handle lithiated species and add 14 new reaction families to RMG. RMG is additionally extended to simulate electrocatalytic systems. Lastly, we demonstrate RMG on the decomposition of acetonitrile and ethylene carbonate near a battery anode. Furthermore, while this framework does not yet resolve individual ions, as appropriate thermochemistry estimators are not available, and thus, cannot yet resolve more complex electrochemical pathways, RMG is able to generate reasonable pathways for SEI formation that match literature pathways and products. In particular, RMG identifies a new important reaction pathway that is not present in literature.

Chemical reactions↗
DOE OSTI2025

Quantifying the Reactivity of Isolated Li x Si Domains in Si Anodes Using Operando NMR

The use of Si anodes can greatly improve the energy density of Li-ion batteries. However, understanding and mitigation of calendar aging remains a barrier to commercialization. Here, in this short report, we utilize operando Nuclear Magnetic Resonance (NMR) spectroscopy to detect and quantify lithium silicides (Li x Si) as they form and react within Si anodes in pouch cells during calendar aging. We provide direct experimental evidence of complex aging phenomena in the Si anodes, including both SEI growth and dissolution during storage. Formation of electrochemically isolated Li x Si is also observed, as indicated by the partial persistence of highly lithiated phases after the cell is discharged. Remarkably, we show that these isolated domains can themselves self-discharge over time, suggesting that their detection can be challenging in post-mortem studies. Finally, we show that aging outcomes depend heavily on the type of silicon particles contained within the electrode, and that certain surface coatings can help decrease the reactivity between lithium silicides and the electrolyte.

Li-ion battery↗
DOE OSTI2024

Defect-Driven Configurational Entropy in the High-Entropy Oxide Li 1.5 MO 3-δ

Layered lithiated oxides are promising materials for next generation Li-ion battery cathode materials; however, instability during cycling results in poor performance over time compared to the high capacities theoretically possible with these materials. Here, in this paper, we report the characterizations of a Li 1.47 Mn 0.57 Al 0.13 Fe 0.095 Co 0.105 Ni 0.095 O 2.49 high-entropy layered oxide (HELO) with the Li 2 MO 3 structure where M = Mn, Al, Fe, Co, and Ni. Using electron microscopy and X-ray spectroscopy, we identify a homogeneous Li 2 MO 3 structure stabilized by the entropic contribution of oxygen vacancies. This defect-driven entropy would not be attainable in the LiMO 2 structure sometimes observed in similar materials as a secondary phase owing to the presence of fewer O sites and a 3+ oxidation state for the metal site; instead, a Li 2-γ MO 3-δ is produced. Beyond Li 2 MO 3 , this defect-driven entropy approach to stabilizing novel compositions and phases can be applied to a wide array of future cathode materials including spinel and rock salt structures.

25 ENERGY STORAGE↗
DOE OSTI2026

Prelithiated SiO x /Graphite-NMC811 Cells: Capacity Loss, Impedance Rise and Hidden Degradation Pathways Revealed Using Three-Electrode Diagnostics

Electrodes containing SiO x /graphite (Gr) materials are attractive as anodes for high-energy lithium-ion batteries. However, their mechanical deformation, electrochemical response, and impedance evolution during long-term cycling are strongly coupled, complicating accurate diagnosis of performance fade mechanisms. In this work, the behavior of electrochemically prelithiated SiO x /Gr anodes paired with NMC811 cathodes is systematically investigated using techniques that include in-situ dilatometry, three-electrode electrochemistry, and multiscale post-cycling microscopy. The SiO x /Gr electrode exhibits a maximum expansion of 49% upon lithiation to 10 mV vs Li + /Li, with 84% of the expansion and 91% of the capacity being reversible. In full cells, relatively stable cycling with only 12% capacity fade over 500 cycles is observed. Three-electrode experiments reveal cell-level impedance growth, which is dominated by the NMC811 cathode: the SiO x /Gr anode exhibits minimal net impedance rise and an initial impedance decrease at low potentials. Despite this apparent electrochemical stability, cross-sectional SEM, PFIB tomography, and cryo-STEM reveal irreversible anode thickening caused by the accumulation of an inorganic-rich solid electrolyte interphase (SEI) permeating the anode bulk. Electrode potential-shift analysis further demonstrates that Li + ions released from lithium reservoirs in the prelithiated anode mask true lithium inventory loss during aging. These results demonstrate that low-expansion SiO x /Gr anodes can simultaneously exhibit favorable cycling and impedance metrics while undergoing substantial, hidden degradation, underscoring the importance of electrode-resolved diagnostics for evaluating prelithiated silicon-based anodes.

25 ENERGY STORAGE↗
DOE OSTI2025

Two-Dimensional Siloxene Nanosheets: Understanding the Effect of Heat Treatment on the Surface Chemistry and Resulting Electrochemistry in Lithium-Based Batteries

Two-dimensional (2D) silicon materials are conceptually appealing as negative electrode materials in lithium-ion batteries due to their layered morphology, which can accommodate (de)lithiation-induced volume changes. Herein, heat treatment of 2D Siloxene materials was used to modify the surface functional groups to determine the impact on the electrochemical behavior. Spectroscopic characterization of the heat-treated nanosheets confirmed the loss of oxygenated and hydride surface functional groups with an increased annealing temperature. Formation and disproportionation of the amorphous suboxides with increasing heat treatment were affirmed with lab and synchrotron-based measurements. A reduced irreversible capacity was observed for Siloxene with a higher temperature heat treatment consistent with the formation of a more favorable surface electrolyte interphase (SEI). A Siloxene-400||NMC622 full cell (prepared with 400 °C-annealed Siloxene (Siloxene-400) and LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622)) showed significantly enhanced capacity and rate capability compared to a nano Si||NMC622 cell. Finally, these results illustrate the ability of thermal annealing to modify the surface functional groups of Siloxene and highlight the favorable impact of the appropriate surface functionality on the electrochemistry of Siloxene in lithium cells.

25 ENERGY STORAGE↗
DOE OSTI2025

Reactivity of Carbonate Solvent Electrolytes on Lithium Silicon Anodes

Silicon (Si) is promising for lithium-ion battery (LIB) anodes due to their high theoretical capacity and low electrochemical potential. However, significant challenges remain, including severe volumetric expansion during cycling and the electrochemical instability of electrolytes, which leads to the formation of a nonuniform solid electrolyte interphase (SEI). To investigate SEI formation mechanisms, computational molecular dynamics simulations offer valuable insights. In this work, we examine the trajectories and charge transfer behavior of lithium hexafluorophosphate (LiPF 6 ) salt with various solvent compositions using density functional theory (DFT) and ab initio molecular dynamics (AIMD). Among the tested electrolyte systems, LiPF 6 with vinylene carbonate (VC) added to ethyl methyl carbonate (EMC) exhibits the lowest reactivity with the Si anode. In contrast, the effects of fluoroethylene carbonate (FEC) and VC depend on whether the primary solvent is EMC alone or a mixture of ethylene carbonate (EC) and EMC. Moreover, we show that electrolyte reactivity varies with the degree of lithiation of the Si anode (LiSi vs Li 15 Si 4 ) and under different charge states. To decouple electrolyte reactivity from surface effects, we analyze the dissociation and formation energies of individual species from solvated configurations. Overall, these first-principles-based findings provide a strategic foundation for electrolyte design to improve cycling stability and extend calendar life in LIBs using Si anodes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Oxygen Vacancy Evolution at Li x V 2 O 5 /LiPON Solid State Electrochemical Interfaces Using Depth Resolved Cathodoluminescence Spectroscopy

The formation of oxygen vacancies at buried LiPON/ Li x V 2 O 5 interfaces has been observed on a near-nanometer scale and nondestructively using depth-resolved cathodoluminescence spectroscopy (DRCLS) and interfacial markers. Before electrochemical cycling, as-deposited LiPON/Li x V 2 O 5 exhibits a 1.6 eV defect optical emission, which density functional theory calculations identify as originating from oxygen vacancies. This defect appears first within a few nanometers of the buried LiPON/Li x V 2 O 5 interface without cycling, indicating that spontaneous O diffusion from the Li x V 2 O 5 lattice into LiPON may have caused these interface-localized oxygen vacancy defects. DRCLS measured the intensity and spatial distribution of this oxygen vacancy signal as a function of electrochemical cycling in a LiPON/Li x V 2 O 5 half-cell, showing oxygen vacancy signal increasing and moving deeper into the electrode with increased cycle number. Significant electrochemical irreversibility was also observed, with poor Coulombic efficiency and a 15% drop in capacity over 50 cycles. Theoretical simulations predict that the presence of oxygen vacancies increases the energy barrier for lithium diffusion significantly, indicating that this aggregation of oxygen vacancies could be another battery degradation mechanism accompanying lithiation induced phase changes.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Intercalative Redox Tuning for Cu/Li x Mn 2 O 4 -Catalyzed Oxidative Alkyne Coupling

Modulation of heterogeneous catalyst structure is ubiquitous within efforts to improve catalytic activity and selectivity at the molecular level. Herein, manganese oxide (MnO 2 ) is employed as a continuously tunable catalyst support through increasing extent of lithium intercalation and reduced surface potential. Oxidative grafting of an organocopper complex onto various lithium manganese oxides (Li x Mn 2 O 4 , x = 0-2.1) produced divalent and monovalent copper species on the partially reduced (0 ≤ x ≤ 1.2) and fully reduced (x = 2.1) surfaces, respectively, as determined by X-ray absorption fine structure (XAFS) analysis. In this study, the resultant materials are catalytically active for the oxidative coupling of terminal alkynes, with steady-state reaction rate data of oxidative propyne dimerization (200 °C, 0.6-2.4 kPa propyne, 2.4-9.9 kPa O 2 ) indicating that complete support lithiation (Li 2.1 Mn 2 O 4 ) provides increased catalytic performance and renders reoxidation steps less kinetically demanding compared to the unreduced parent material. Enacting a dual site (Cu and MnO x ) kinetic model can account for dimerization rates measured over Cu/Li 2.1 Mn 2 O 4 under various reactant concentrations, copper loadings, and surface coverages, providing supporting evidence for the synergistic role of the metal and support in facilitating the coupling reaction. Overall, results presented here provide an extension for general strategies of systematically controlling catalytic structure and function through lithium reduction of bulk oxides and subsequent electronic modulation of the metals supported thereon.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Topological Considerations in Electrolyte Additives for Passivating Silicon Anodes with Hybrid Solid–Electrolyte Interphases

Unlike most anodes used in high energy density batteries, lithiated Si does not form long-lasting passivating solid-electrolyte interphases (SEI) during formation or on charge due to SEI delamination, reconstruction, or dissolution. As a result, electrolyte degradation is continuous and results in a permanent loss of the Li inventory, shortening the useful life of the battery. Here, in this study, we show that perfluoroether electrolyte additives featuring either sulfonyl fluorides or trifluorovinyl ethers, when introduced in prescribed amounts to locally superconcentrated electrolytes, exhibit preferential reactivity at Si during formation due to their higher reduction potential than salts and solvents, creating a hybrid SEI that is simultaneously enriched with LiF and organics tethered to the reactive functionality. While both reactive motifs are effective in creating a hybrid SEI, perfluoroether additives bearing sulfonyl fluorides show more substantial integration. More important, however, is the combined influence of additive topology on anchoring efficacy and tether flexibility between anchoring sites on SEI resiliency. Top-performing Si|LFP cells featuring ditopic additive-enriched SEI improve capacity retention by as much as 45% over 100 cycles when compared to additive-free cells.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Fracture Dynamics in Silicon Anode Solid-State Batteries

Solid-state batteries (SSBs) with silicon anodes could enable improved safety and energy density compared to lithium-ion batteries. However, degradation arising from the massive volumetric changes of silicon anodes during cycling is not well understood in solid-state systems. Here, we use operando X-ray computed microtomography to reveal micro- to macro-scale chemo-mechanical degradation processes of silicon anodes in SSBs. Mud-type channel cracks driven by biaxial tensile stress form across the electrode during delithiation. We also find detrimental cracks at the silicon/ solid electrolyte interface that form due to local reaction competition between neighboring domains of different sizes. Continuum phase-field damage modeling quantifies stress-driven channel cracking and shows that the lithiated silicon stress state is critical for determining the extent of interfacial fracture. This work reveals the mechanisms that govern SSBs compared to conventional lithium-ion batteries and provides guidelines for engineering chemomechanically resilient electrodes for high-energy batteries.

25 ENERGY STORAGE↗
DOE OSTI2025

Two-Dimensional Tantalum Carbo-Selenide for Hydrogen Evolution

Herein, we report the synthesis of two-dimensional Ta 2 Se 2 C (2D-Ta 2 Se 2 C) nanosheets using electrochemical lithiation in multilayer Ta 2 Se 2 C followed by sonication in deionized water. Multilayer Ta 2 Se 2 C was obtained via solid-state synthesis of Fe x Ta 2 Se 2 C followed by chemical etching of Fe. 2D-Ta 2 Se 2 C exhibited promising electrocatalytic activity for the hydrogen evolution reaction from water compared to multilayer Ta 2 Se 2 C and 2D-TaSe 2 . 2D-Ta 2 Se 2 C showed an overpotential at 10 mA·cm -2 (η 10 ) of 264 mV, a Tafel slope of 91 mV·dec -1 , and an electrochemically active surface area of 17.61 m ECSA 2 ·g catalyst -1 . The high performance could be attributed to the large surface area of single sheets which hence maximizes the number of exposed catalytic sites and increased density of vacancies, observed with transmission electron microscopy, during synthesis and processing.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Solvent-Mediated, Reversible Ternary Graphite Intercalation Compounds for Extreme-Condition Li-Ion Batteries

Traditional Li-ion intercalation chemistry into graphite anode exclusively utilizes the co-intercalation-free or co-intercalation mechanism. The latter mechanism is based on ternary graphite intercalation compounds (t-GICs), where glyme solvents were explored and proved to deliver unsatisfied cyclability in LIBs. Herein, we report a novel intercalation mechanism, that is, in-situ synthesis of t-THF-GICs in the tetrahydrofuran (THF) electrolyte via a spontaneous, controllable reaction between binary-GICs and free THF molecules during initial graphite lithiation. The spontaneous transformation from b-GIC to t-GIC, which is different from conventional co-intercalation chemistry, is characterized and quantified via operando synchrotron X-ray and electrochemical analyses. The resulting t-GIC chemistry obviates the necessity for complete Li-ion desolvation, facilitating rapid kinetics and synchronous charge/discharge of graphite particles even under high current densities. Consequently, the graphite anode demonstrates unprecedented fast charging (1 min), dendrite-free low-temperature performance, and ultralong lifetimes exceeding 10,000 cycles. Full cells coupled with layered cathode, display remarkable cycling stability upon a 15-min charging and excellent rate capability even at -40 °C. Furthermore, our chemical strategies are shown to extend beyond Li-ion batteries to encompass Na-ion and K-ion batteries, underscoring their broad applicability. Our work contributes to the advancement of graphite intercalation chemistry and presents a low-cost, adaptable approach to achieving fast-charging and low-temperature batteries.

25 ENERGY STORAGE↗
DOE OSTI2025

Precise Synthesis of 4.75 V-Tolerant LiCoO 2 with Homogeneous Delithiation and Reduced Internal Strain

The rapid advancements in 3C electronic devices necessitate an increase in the charge cutoff voltage of LiCoO 2 to unlock a higher energy density that surpasses the currently available levels. However, the structural devastation and electrochemical decay of LiCoO 2 are significantly exacerbated, particularly at ≥4.5 V, due to the stress concentration caused by more severe lattice expansion and shrinkage, coupled with heterogeneous Li + intercalation/deintercalation reactions. Herein, employing the molten-salt synthesis technique, we propose a universal morphology-shaping strategy to attain bulk reaction homogeneity and reduce internal strains, even at extremely high charge voltages. The newly designed flattened polygon prismlike LiCoO 2 (P-LCO) particle, featuring a regular symmetrical arrangement along the c-axis, demonstrates a more homogeneous Li + extraction/insertion reaction, which results in a restrained transformation to detrimental O1 phase and reduced variation in lattice volume throughout the (de)lithiation processes. This benefits the mitigation of the local stress accumulation misfit dislocations and particle cracking, ultimately maintaining the mechanical stability of the cathode. Consequently, P-LCO is capable of breaking the voltage ceiling and exhibits exceptional long-term cycling capability at an ultrahigh voltage of 4.75 V. In conclusion, this work offers a brand-new perspective for the rational design of cathode morphology to address capacity deterioration caused by inhomogeneous delithiation and internal strain, thus inspiring the development of high-energy-density cathodes with improved durability.

36 MATERIALS SCIENCE↗