Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Laser cladding”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Dopant Segregation in Single-Crystal Optical Fiber Grown via the Laser-Heated Pedestal Growth Technique

Single crystal (SC) optical fiber has promising potential to be used for optical fiber sensing applications in harsh conditions due to its robustness to high temperature, high radioactivity, and resistance to chemical corrosion as compared to optical sensors using silica fiber. However, SC fiber grown via the laser-heated pedestal growth (LHPG) technique innately does not have a core-cladding structure found in standard optical fiber, resulting in optical losses. In this work we investigate optimization of the growth parameters of a two LHPG process used to grow SC fiber with a graded index via introduction of dopants to the feedstock material. Feedstock material is fabricated with the first LHPG device, then sol-gel dip-coated to create outer films of dopant material. The dip-coated feedstock is used to grow SC fiber in which segregation of the dopant constituents occurs, resulting in a graded index of refraction across the fiber, and an effective core-cladding structure. Hardware and software improvements to both LHPG systems are presented and the growth parameters for short pieces of ~320-330 μm diameter YAG fiber has been established. Characterization techniques/procedures have also been established for future grown SC fiber. These improvements and preparations are anticipated to result in a significant increase in grown fiber quality with a similar growth rate to that previously established.

Lander, Gary↗
DOE OSTI2024

Dopant Segregation in Single-Crystal Optical Fiber Grown via the Laser-Heated Pedestal Growth Technique

Single crystal (SC) optical fiber has promising potential to be used for optical fiber sensing applications in harsh conditions due to its robustness to high temperature, high radioactivity, and resistance to chemical corrosion as compared to optical sensors using silica fiber. However, SC fiber grown via the laser-heated pedestal growth (LHPG) technique innately does not have a core-cladding structure found in standard optical fiber, resulting in optical losses. In this work we investigate optimization of the growth parameters of a two LHPG process used to grow SC fiber with a graded index via introduction of dopants to the feedstock material. Feedstock material is fabricated with the first LHPG device, then sol-gel dip-coated to create outer films of dopant material. The dip-coated feedstock is used to grow SC fiber in which segregation of the dopant constituents occurs, resulting in a graded index of refraction across the fiber, and an effective core-cladding structure. Hardware and software improvements to both LHPG systems are presented and the growth parameters for short pieces of ~320-330 μm diameter YAG fiber has been established. Characterization techniques/procedures have also been established for future grown SC fiber. These improvements and preparations are anticipated to result in a significant increase in grown fiber quality with a similar growth rate to that previously established.

Lander, Gary↗
DOE OSTI2021

Electrically Pumped Epitaxially Regrown GaSb-Based Type-I Quantum-Well Surface-Emitting Lasers with Buried High-Index-Contrast Photonic Crystal Layer

Epitaxially regrown electrically pumped photonic crystal surface-emitting lasers (PCSELs) emitting near 2 and 2.6 μm are designed, fabricated, and characterized. A high-index-contrast photonic crystal layer is incorporated into the GaSb-based laser heterostructure by air-hole-retaining epitaxial regrowth. A square lattice of triangular holes is etched in the top waveguide core layer of the incomplete laser heterostructure. The nanopatterned surface is subsequently cleaned and regrown with AlGaAsSb p-cladding material. Transmission electron microscopy studies demonstrate uniform regrowth over the nanopatterned GaSb surface. The selected regrowth regimes yield a buried 2D array of elongated air-holes. The diode PCSELs based on moderately etched nanopatterns demonstrate band-edge lasing near 2 μm up to room temperatures. The cascade diode PCSELs operate near 2.6 μm with minimum threshold current densities of about 500 A cm -2 achieved at 180 K. The devices generate mW level output in narrow divergence beam emitted from the window in substrate contact. The angle-resolved electroluminescence measurements reveal a four-sub-band band structure with an apparent photonic bandgap corresponding to the buried high-index-contrast square photonic crystal layer. Finally, the PCSELs made of heterostructures supporting two modes in the vertical direction demonstrate two sets of sub-bands showing anti-crossing-like interaction.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
NASA NTRS1988

Development program for 1.93-micron lasers

For the first time lasers operating at 1.93 microns were demonstrated. The lasers were fabricated by Vapor Phase Epitaxial (VPE) growth techniques currently used for the fabrication of high power lasers at 1.3 microns. The structure of these laser diodes consisted of compositionally graded, sulfur-doped InAsP, grown on an InP substrate; a constant-composition n+InAs(0.27)P(0.73) layer, which is the first cladding layer; an In(0.66)Ga(0.34)As layer, which is the active region, and a second InAs(0.27)P(0.73) layer. The devices were oxide-stripe DH lasers (gain-guided only). The best devices had 80 K lasing thresholds in the range of from 80 to 150 mA, and T sub o (below 220 K) in the range of 60 to 90 K. The highest observed temperature of oscillation was 15.5 C. The highest observed power output at 80 K was in the range of 3 to 5 mW. The calculated delta I/delta T was 4.4 A/K. As a part of the materials development, PIN homojunction detectors having the band edge near 1.93 were also fabricated. The best devices (100 micron diameter, mesa structure) exhibited room temperature dark currents in the range of from 20 to 50 nA and had QE at 1.93 microns in the range of 35 to 40 percent. In addition to the device results, the InGaAs-InAsP materials system was extensively investigated and low defect density layers can now be grown allowing for significant device performance improvement.

Longeway, P.↗
NASA NTRS1993

Experimental verification of a theoretical model of an active cladding optical fiber fluorosensor

Experiments were conducted to verify a theoretical model on the injection efficiency of sources in the cladding of an optical fiber. The theoretical results predicted an increase in the injection efficiency for higher differences in refractive indices between the core and cladding. The experimental apparatus used consisted of a glass rod 50 cm long, coated at one end with a thin film of fluorescent substance. The fluorescent substance was excited with side illumination, perpendicular to the rod axis, using a 476 nm Argon-ion laser. Part of the excited fluorescence was injected into the core and guided to a detector. The signal was measured for several different cladding refractive indices. The cladding consisted of sugar dissolved in water and the refractive index was changed by varying the sugar concentration in the solution. The results indicate that the power injected into the rod, due to evanescent wave injection, increases with the difference in refractive index which is in qualitative agreement with theory.

Albin, Sacharia↗
NASA NTRS1985

Arrangement for damping the resonance in a laser diode

An arrangement for damping the resonance in a laser diode is described. This arrangement includes an additional layer which together with the conventional laser diode form a structure (35) of a bipolar transistor. Therein, the additional layer serves as the collector, the cladding layer next to it as the base, and the active region and the other cladding layer as the emitter. A capacitor is connected across the base and the collector. It is chosen so that at any frequency above a certain selected frequency which is far below the resonance frequency the capacitor impedance is very low, effectively shorting the base to the collector.

Katz, J.↗
NASA NTRS2006

Multipurpose Microspheres-Fiber Laser

Doped silica microspheres are used to build a novel, rugged, and tunable laser system. The injected microspheres into a hollow fiber are pumped externally and their emission is collected along the cladding of the fiber.

Abdeldayem, Hossin↗
NASA NTRS1981

Fiber optics transmission of LV signal

The first use of a long optical fiber for transmitting megahertz frequencies in a laser velocimeter (LV) receiver system is reported. The fiber comprises a 600-micron diameter fused silica core, a silicon polymer cladding and a plastic jacket. The fiber numerical aperture is 0.22, corresponding to a maximum entrance half-angle of 0.22 rad. The 10-m length used results in a 5.6% attenuation loss. The fiber is found to transmit an 80-MHz signal with excellent resolution. It is established that an LV receiver using fiber optics sends a clean signal in electronically noisy and high-pressure environments and allows velocity measurements in places too small for a photomultiplier tube.

Young, A. D.↗
NASA NTRS1974

Diffused optical waveguides

Diffused optical waveguides are studied using the modal and the ray tracing approach, with an emphasis on the case of a hollow waveguide with diffuse cladding. The properties of the guided modes are investigated in detail. The applications of these structures to optical circuits, integrated optics lasers and capillary gas lasers are discussed.

Elachi, C.↗
NASA NTRS1987

Uranium nitride fuel fabrication for SP-100 reactors

Fuel pins of uranium mononitride clad in Nb-1 percent Zr were fabricated for irradiation tests in EBR-II. Laboratory scale process parameters to synthesize UN powders and fabricate UN pellets were developed. Uranium mononitride was prepared by converting UO2 to UN. Fuel pellets were prepared by communition of UN briquettes, uniaxial pressing, and high temperature sintering. Techniques for machining, cleaning, and welding Nb-1 percent Zr cladding components were developed. End caps were electron beam welded to the tubing. Helium back-fill holes were sealed with a laser weld.

Mason, Richard E.↗
DOE OSTI2023

Enhanced backscatter and unsaturated blue wavelength shifts in F-doped fused silica optical fibers exposed to extreme neutron radiation damage

Amorphous fused silica (a-SiO 2 ) optical fibers, with and without inscribed Bragg gratings, were interrogated using infrared (~1550 nm) optical backscatter reflectometry during ~25 days of intense neutron irradiation to a fast (energy > 0.1 MeV) neutron fluence of ~10 21 n/cm 2 , or ~1.5 atomic displacements per atom. The reflected light amplitudes in Ge-doped core telecommunications fiber dropped below detection limits (>15 dB attenuation) within 3 days of irradiation (~10 20 fast n/cm 2 ). Here, amplitudes from a pure silica core, F-doped silica cladding fiber reached equilibrium levels ~1.5–2 dB higher than pre-irradiation values, whereas Bragg gratings inscribed in the same fiber using a femtosecond laser (point-by-point method) suffered > 45 dB attenuation. Blue wavelength shifts were initially consistent with previous radiation-induced compaction models but increased linearly with increasing neutron fluence (no evidence of saturation) beyond 10 20 n/cm 2 and exceeded 0.6%, which corresponds to >1,000 °C drift if used to measure temperature changes.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Parametric Optimization of Nanostructured Alumina Forming Austenitic Alloys

Alumina-forming austenitic (AFA) alloys provide excellent oxidation resistance through the formation of a stable alumina scale, but their relatively high Ni content might limit application in core structural components because of helium generation and swelling under irradiation. Increasing the density of nanoscale features in the microstructure is a promising route to improve sink strength and mitigate these effects. Conventional oxide dispersion–strengthened (ODS) steels achieve this through mechanical alloying (MA), but the approach is costly and difficult to scale. In this milestone, additive manufacturing was applied as an alternative pathway to fabricate nanostructured AFA (NAFA) alloys with dual precipitation of oxides and nitrides enabled by reactive atmosphere processing. In FY25, two compositions, NAFA-1 (AFA-05) and NAFA-2, were produced and compared. Both alloys achieved densities above 99% of theoretical values, but NAFA-2 exhibited microcracking associated with Nb-rich intermetallic formation, indicating the need for further chemistry optimization. Nitrogen and oxygen uptake was confirmed on selected builds, demonstrating the intended dual-precipitate dispersion. Mechanical testing showed that AM-processed NAFA alloys exceed conventionally produced ODS steels in high-temperature tensile strength and fracture toughness. Preliminary Cu ion irradiation results further suggest improved resistance compared to wrought austenitic alloys. While the current alloys are promising for their compatibility in high-temperature air or liquid Pb environments, modifications to composition will be required for long-term operation in high-temperature impure sodium systems. Future work will focus on refining alloy chemistry to suppress laser powder bed fusion–induced cracking and scaling production to reactor-relevant dimensions using directed energy deposition as a pathway toward net-shape cladding fabrication.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Strategies for Fabricating Molybdenum Structures Using Laser Powder Bed Fusion

Advances in manufacturing techniques are viewed as enabling technologies for development of high performance nuclear fuel forms that couple high uranium density with improvements to key properties such as thermal conductivity unattainable through conventional fabrication routes. Additive manufacturing (AM) enables the fabrication of complex fuel geometries that are difficult or impossible to achieve using conventional manufacturing methods. Melting-based AM processes, such as laser powder bed fusion (LPBF), provide high geometric resolution (>200 µm depending on the feature) across a variety of metal alloys, including those suitable for high-temperature fuel cladding applications, such as Nb, W, and Mo. Molybdenum is particularly attractive due to its high thermal conductivity, low thermal expansion, and excellent mechanical stability at elevated temperatures. However, its high melting temperature and brittle nature at low temperatures pose significant challenges during LPBF processing. Rapid solidification inherent to LPBF induces high residual stresses, often leading to post-solidification cracking, which limits the manufacturability of Mo components via this method.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS2001

Joint EPA/NASA/USAF Interagency Depainting Study

Environmental regulations such as National Emission Standards for Hazardous Air Pollutants (NESHAPs) are drivers for the implementation of environmentally compliant methodologies in the manufacture of aerospace hardware. In 1995, the Environmental Protection Agency (EPA) promulgated the NESHAP for the Aerospace Manufacture and Rework (Aerospace NESHAP) industry. Affected facilities were to be in compliance by September 1998. Several aerospace manufacturing operations are regulated within the Aerospace NESHAP including Depainting operations. The National Aeronautics and Space Administration (NASA), EPA, and United States Air Force (USAF) combined resources to evaluate the performance of nine alternative depainting processes. The seven alternative depainting processes were: (1) Chemical stripping (non-methylene chloride); (2) Carbon Dioxide Blasting; (3) Xenon Flashlamp; (4) Carbon Dioxide Laser Stripping; (5) Plastic Media Blasting; (6) Sodium Bicarbonate Wet Stripping; and (7) Waterjet Blasting and Wheat Starch Blasting. All epoxy primer and polyurethane top coat system was applied to 2024-T3 clad and non-clad aluminum test specimens. Approximately 200 test specimens were evaluated in this study. Each coupon was subjected to three, four, or five complete depainting cycles. This paper discusses the conclusions from the study including the test protocol, test parameters, and achievable strip rates for the alternative depainting processes. Test data includes immersion corrosion testing, sandwich corrosion testing and hydrogen embrittlement testing for the non-methylene chloride chemical strippers. Additionally, the cumulative effect of the alternative depainting processes on the metallurgical integrity of the test substrate is addressed with the results from tensile and fatigue evaluations.

Clark-Ingram, M.↗
DOE OSTI2024

Length scale effects of micro- and meso-scale tensile tests of unirradiated and irradiated Zircaloy-4 cladding

Zircaloy-4 is an essential material for cladding structures within fission-based reactors. To explore the changes in properties measured on differing length scales, FIB-machined micro-scale tensile tests were performed on both irradiated and control groups of Zircaloy-4. This was correlated with tensile testing on femtosecond laser-machined meso-scale specimens. Pronounced size effects were found when varying specimen geometry. Increases in tensile geometry size were associated with a reduction in measured yield stress for both irradiated and unirradiated samples. Here, meso-scale testing found strength and strain values similar to that of bulk-scale testing.

36 MATERIALS SCIENCE↗
DOE OSTI2024

In-situ kinetic study of irradiation induced crystallization in amorphous Al 2 O 3

In the last ten years amorphous alumina coatings, deposited by Pulsed Laser Deposition, emerged as potential key enabling technology in the fields of heavy liquid metal fast reactors (lead and lead-bismuth) and fusion. In the former, as coating of the steel fuel cladding and in the latter as multifunctional coating providing a barrier against tritium permeation, steel corrosion and electrical insulation. Nevertheless, a detailed knowledge of the behavior of this thermodynamically metastable material at high temperatures and under neutron irradiation is still unknown. A knowledge gap that is mandatory to fill up for the deployment of this barrier technology. In the present work, we present a first step towards this goal, by the in-situ dynamic observation of the radiation induced crystallization processes of thin films of amorphous Al 2 O 3 , induced by ion-irradiation over an extensive range of temperatures (400-800 °C). The study was performed at the Intermediate Voltage Electron Microscope (IVEM)-Tandem Facility at Argonne National Laboratory. The experimental findings allow to elucidate the dependence of the grain growth on ion dose and temperature. A kinetic approach has been used to derive the process activation energies and other important parameters.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Probing Microstructure-induced Swelling & Thermal Property Changes in Ion-Irradiated Oxide Fuels using Laser-generated Surface Acoustic Waves

Radiation of fuel rods with neutrons during a fission reaction in a nuclear reactor is known to affect the material microstructure of the fuel as a result of fission fragment damage, and lead to the formation of atomic-level defects such as voids, dislocation loops, and lattice swelling from fission-gas release. A consequence of the radiation-induced damage in nuclear fuels is the drastic alteration of material properties, in particular, the reduction of the thermal conductivity – a key parameter that governs the transport of thermal energy released from fissile fuel atoms to the surrounding coolant. Swelling can induce high stresses and ultimate failure of the cladding. A fundamental understanding of the role of radiation-induced damage on the thermal transport and mechanical properties of nuclear fuels is therefore critical for efficient, reliable and safe operation of a nuclear power plant. As opposed to conventional post-irradiation examination techniques that are often time-consuming and require significant sample preparation, laser-based characterization methods have emerged as promising non-contact, non-destructive tools to measure the evolution of microstructure-induced material property changes. Moreover, laser methods offer the promise of in-situ characterization while the material is being irradiated. This project aims to develop an improved understanding of the impact of radiation-induced changes to material microstructure on the thermal and elastic properties of nuclear materials. A laser ultrasonic technique, known as the transient grating (TG) spectroscopy method, is used to simultaneously measure thermal diffusivity and elastic properties in unirradiated and ion-irradiated oxide nuclear fuel samples. The results will complement on-going investigations on electron- and phonon-mediated thermal transport in nuclear materials and will provide foundational work for incorporating the influence of defects in fuel performance codes.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1993

Strained layer InP/InGaAs quantum well laser

Strained layer single or multiple quantum well lasers include an InP substrate, a pair of lattice-matched InGaAsP quarternary layers epitaxially grown on the substrate surrounding a pair of lattice matched In.sub.0.53 Ga.sub.0.47 As ternary layers surrounding one or more strained active layers of epitaxially grown, lattice-mismatched In.sub.0.75 Ga.sub.0.25 As. The level of strain is selected to control the bandgap energy to produce laser output having a wavelength in the range of 1.6 to 2.5 .mu.m. The multiple quantum well structure uses between each active layer. Diethyl zinc is used for p-type dopant in an InP cladding layer at a concentration level in the range of about 5.times.10.sup.17 /cm.sup.3 to about 2.times.10.sup.18 /cm.sup.3. Hydrogen sulfide is used for n-type dopant in the substrate.

Forouhar, Siamak↗