Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “LEGS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

Energy Efficient Legged Robotics at Sandia Labs

Sandia is developing energy efficient actuation and drive train technologies to dramatically improve the charge life of legged robots. The work is supported by DARPA, and Sandia will demonstrate an energy efficient bipedal robot at the technology exposition section of the DARPA Robotics Challenge Finals in June, 2015. This video, the first in a series, describes early development and initial integration of the Sandia Transmission Efficient Prototype Promoting Research (STEPPR) robot.

42 ENGINEERING↗

An Investigation of Passive and Semi-Active Tuned Mass Dampers for a Tension Leg Platform Floating Offshore Wind Turbine in ULS Conditions

Offshore Wind Turbines (OWTs) are subjected to complex external loadings caused by combined wind and wave sources. The application of structural damping control techniques to OWTs using Tuned Mass Dampers (TMDs) has shown to be effective in reducing the integrated system loads and accelerations. In this work, the impact of passive and semi-active (S-A) TMD’s applied to both fixed-bottom (monopile) and floating (tension leg platform) OWTs are evaluated under the Fatigue Limit State (FLS) and Ultimate Limit State (ULS). Different S-A control logics like ON/OFF state damping based on the ground hook (GH) control policy are implemented, and the frequency response of each algorithm is investigated. It is shown that the performance of each algorithm varies according to the load conditions such as FLS (normal operation) and ULS (idling state). Fully-coupled time domain simulations are conducted through the developed simulation tool for structural control integrated into the high-fidelity wind turbine design code, FASTv8. Compared to the passive TMD, it is shown that a S-A TMD results in higher load reductions, as well as, smaller strokes under both FLS and ULS conditions. In FLS analysis, the S-A TMD using Displacement Based Ground Hook (DB-GH) control is capable of reducing the fore-aft and side-to-side damage equivalent loads for the monopile substructure by approximately 12 % and 64 %, respectively. The ultimate loads at the tower base for the floating substructure (TLP) are also reduced by 9% with S-A TMD followed by Inverse Velocity Based Ground Hook control (IVB-GH). The dynamic characteristics and practical feasibility of a magnetorheological (MR) damper (for S-A control) are also evaluated.

17 WIND ENERGY↗

Magnetic Resonance Imaging and Spectroscopy to Assess Leg Muscle Macrostructure and Microstructure in Healthy Older Women: A Feasibility Assessment

Advanced magnetic resonance (MR) scanning techniques, such as diffusion tensor imaging (DTI) and proton MR spectroscopy ({sup 1}H-MRS) permit microstructural evaluation of water diffusivity and intramyocellular lipid content, respectively. We aimed to determine the feasibility of performing advanced MR scanning (proton density [PD] weighted imaging, DTI, and {sup 1}H-MRS) to evaluate properties of leg muscles in older women with respect to: (1) participant recruitment using three community-based strategies; (2) participant tolerance to the MRI scan acquisition protocol; and (3) scan acquisition and analyses protocols.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

PET Imaging of Leg Arteries for Determining the Input Function in PET/MRI Brain Studies Using a Compact, MRI-Compatible PET System

In this work, we used a compact, high-resolution, and magnetic resonance imaging (MRI)-compatible positron emission tomography (PET) camera (VersaPET) to assess the feasibility of measuring the image-derived input function (IDIF) from arteries in the leg with the ultimate goal of enabling fully quantitative PET brain imaging without blood sampling. We used this approach in five 18 F-FDG PET/MRI brain studies in which the input function was also acquired using the gold standard of serial arterial blood sampling. After accounting for partial volume, dispersion, and calibration effects, we compared the metabolic rates of glucose (MRglu) quantified from VersaPET IDIFs in 80 brain regions to those using the gold standard and achieved a bias and variability of <5% which is within the range of reported test-retest values for this type of study. We also achieved a strong linear relationship (R 2 >0.97) against the gold standard across regions. The results of this preliminary study are promising and support further studies to optimize methods, validate in a larger cohort, and extend to the modeling of other radiotracers.

47 OTHER INSTRUMENTATION↗

Conceptual Design of a Tension Leg Platform With 22.3 MW Vertical Axis Turbine

Here, this paper presents the conceptual design of a tension leg platform (TLP) for the ARCUS “towerless” vertical-axis wind turbine (VAWT). VAWTs are ideal for floating offshore sites and have several advantages over horizontal-axis wind turbines (HAWT) including reduced top mass, lower center of gravity, increased energy capture, and in turn lower cost. The towerless ARCUS VAWT drives these advantages further through increased structural efficiency and by enabling more optimized TLP designs with simplified installation procedures. For hull sizing, we have studied three turbine sizes with corresponding power ratings of 5.1 MW, 10.4 MW and 22.3 MW. The largest turbine was identified as having the greatest potential to reduce the levelized cost of energy (LCOE) and is the reference size used for the further detailed design process. The conceptual design of the VAWT TLP has been awarded with an ABS Approval in Principle Certificate. This paper contains brief analysis results and design findings for a TLP designed to house a VAWT, including the following topics: • Applicable Design Codes • Metocean Conditions • ARCUS Turbine Loads • Design Load Cases and Requirements - Pre-service TLP Stability - In-place TLP Global Performance • Platform Configurations, Hull Structure Scantling Design, Weight and CG Estimation, and General Arrangement Drawings • Hull Ballast Plan for both Pre-service and In-place Conditions • Pre-service Quayside Integration, Transportation and Wet Tow Stability Analysis • Global Performance Analysis for Motions and Tendon tensions • Summary of cost components and system levelized cost of energy

17 WIND ENERGY↗

Model Development and Loads Analysis of a Wind Turbine on a Floating Offshore Tension Leg Platform

This report presents results of the analysis of a 5-MW wind turbine located on a floating offshore tension leg platform (TLP) that was conducted using the fully coupled time-domain aero-hydro-servo-elastic design code FAST with AeroDyn and HydroDyn. Models in this code are of greater fidelity than most of the models that have been used to analyze floating turbines in the past--which have neglected important hydrodynamic and mooring system effects. The report provides a description of the development process of a TLP model, which is a modified version of a Massachusetts Institute of Technology design derived from a parametric linear frequency-domain optimization process. An extensive loads and stability analysis for ultimate and fatigue loads according to the procedure of the International Electrotechnical Commission offshore wind turbine design standard was performed with the verified TLP model. Response statistics, extreme event tables, fatigue lifetimes, and selected time histories of design-driving extreme events are analyzed and presented. Loads for the wind turbine on the TLP are compared to those of an equivalent land-based turbine in terms of load ratios. Major instabilities for the TLP are identified and described.

17 WIND ENERGY↗

Model Development and Loads Analysis of an Offshore Wind Turbine on a Tension Leg Platform with a Comparison to Other Floating Turbine Concepts: April 2009

This report presents results of the analysis of a 5-MW wind turbine located on a floating offshore tension leg platform (TLP) that was conducted using the fully coupled time-domain aero-hydro-servo-elastic design code FAST with AeroDyn and HydroDyn. The report also provides a description of the development process of the TLP model. The model has been verified via comparisons to frequency-domain calculations. Important differences have been identified between the frequency-domain and time-domain simulations, and have generated implications for the conceptual design process. An extensive loads and stability analysis for ultimate and fatigue loads according to the procedure of the IEC 61400-3 offshore wind turbine design standard was performed with the verified TLP model. This report compares the loads for the wind turbine on the TLP to those of an equivalent land-based turbine. Major instabilities for the TLP are identified and described.

17 WIND ENERGY↗

Numerical Prediction of Experimentally Observed Behavior of a Scale Model of an Offshore Wind Turbine Supported by a Tension-Leg Platform: Preprint

Realizing the critical importance the role physical experimental tests play in understanding the dynamics of floating offshore wind turbines, the DeepCwind consortium conducted a one-fiftieth-scale model test program where several floating wind platforms were subjected to a variety of wind and wave loading condition at the Maritime Research Institute Netherlands wave basin. This paper describes the observed behavior of a tension-leg platform, one of three platforms tested, and the systematic effort to predict the measured response with the FAST simulation tool using a model primarily based on consensus geometric and mass properties of the test specimen.

17 WIND ENERGY↗

Energy Efficient Legged Robotics at Sandia Labs, Part 2

Sandia is developing energy efficient actuation and drive train technologies to dramatically improve the charge life of legged robots. The work is supported by DARPA, and Sandia will demonstrate an energy efficient bipedal robot at the technology exposition section of the DARPA Robotics Challenge Finals in June, 2015. This video, the second in a series, describes the continued development and integration of the Sandia Transmission Efficient Prototype Promoting Research (STEPPR) robot.

42 ENGINEERING↗

Charge Excitations in Two-Leg Ladders: A tDMRG Approach

Abstract We study the dynamics of holon doublon pairs in two-leg Hubbard ladders with the time-dependent Density Matrix Renormalization-Group approach. Benchmark results show that the Krylov algorithm is well suited to calculate the time dependence of observables in these systems. Furthermore, we show that the dynamics of the holon doublon depend strongly on the coupling asymmetry within the ladder, indicating that the ladder geometry plays a role in the decay of these elementary charge excitations.

Dias da Silva, Luis↗

Combining direct ink writing with reactive melt infiltration to create architectured thermoelectric legs

Here, we present a new additive-reactive synthesis method where inks – cast into molds or 3D-additively extruded into architectured shapes – are reacted into intermetallic thermoelectric compounds. The new method, as demonstrated for equiatomic TiNiSn, combines: (i) extrusion printing (or casting) of inks containing Ni and Ti powders, (ii) debinding and reactive sintering to form a porous NiTi network, (iii) network infiltration with liquid Sn and subsequent reaction to synthesize the TiNiSn phase. Thin plates, created through this method, show high phase purity and low residual porosity. A thermoelectric figure of merit zT = 0.47 ± 0.05 is achieved at 800 K, within the broad range of values (zT= 0.3–1.0) reported for TiNiSn created via traditional powder hot-pressing methods. Layered TiNiSn microlattices – after 3D ink-extrusion printing and infiltration – exhibit high relative densities and minimal undesirable secondary phase content, with a Seebeck coefficient on par with the ink-cast TiNiSn plates, demonstrating that thermoelectric legs with far-ranging architectural freedom can be created additively with this novel reactive manufacturing method. Numerous other thermoelectric (and other) compounds, currently limited to basic geometries due to brittleness, are amenable to this new method based on a sequence of reactive sintering/infiltration of cast or ink-extruded precursors.

36 MATERIALS SCIENCE↗

Competition between charge-density-wave and superconducting orders on eight-leg square Hubbard cylinders

The issue of whether d-wave superconductivity (SC) occurs in the square-lattice Hubbard model with U of order of the bandwidth has been one of the most debated issues to emerge from the study of high temperature SC. Here, we report variational results on eight-leg cylinders with next-nearest-neighbor hopping in the range $-0.5t\le t^{\prime} \le 0.25t$ with U = 8t and 12t and doped hole concentrations δ = 1/12 and 1/8. For $t^{\prime} \le 0$, the ground-state appears to be a charge-density wave (CDW) of one sort or another with SC correlations that are extremely short-ranged. In contrast, in some cases, the local magnetic order has a correlation length greater than half the cylinder width - suggestive that magnetic order might also arise in the 2D limit. For $t^{\prime} \le 0$, our results depend more strongly on boundary conditions (periodic vs antiperiodic), making it still harder to correctly guess whether SC or CDW correlations dominate in the 2D limit. These results were obtained employing matrix-product states with bond dimensions large enough that energy differences as small as 10 −3 t per site can be resolved.

materials science↗

UPFLOWS IN FUNNEL-LIKE LEGS OF CORONAL MAGNETIC LOOPS

The prominent blueshifts of Ne VIII associated with the junctions of the magnetic network in the quiet Sun are still not well understood. By comparing the coronal magnetic-field structures as obtained by a potential-field reconstruction with the conspicuous blueshift patches on the Dopplergram of Ne VIII as observed in an equatorial quiet-Sun region, we find that most of the regions with significant upflow are associated with the funnel-like legs of magnetic loops and cospatial with increments of the line width. These quasi-steady upflows can be regarded as the signatures of mass supply to coronal loops. By using the square root of the line intensity as a proxy for the plasma density, the mass flux of the upflow in each funnel can be estimated. We find that the mass flux is anti-correlated with the funnel's expansion factor as determined from the extrapolated magnetic field. One of the loop systems is associated with a coronal bright point, which was observed by several instruments and exhibited various morphologies in different wavelengths and viewing directions. A remarkable agreement between its magnetic structure and the associated EUV emission pattern was found, suggesting an almost potential-field nature of the coronal magnetic field. We also report the direct detection of a small-scale siphon flow by both STEREO satellites. However, this transient siphon flow occurred in a weak mixed-polarity-field region, which was outside the adjacent magnetic funnel, and thus it is perhaps not related to plasma upflow in the funnel. Based on these observations, we suggest that at upper transition region (TR) temperatures the dominant flows in quiet-Sun coronal loops are long-lasting upflows rather than siphon flows. We also discuss the implications of our results for coronal heating and unresolved magnetic structures.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

ARE GIANT TORNADOES THE LEGS OF SOLAR PROMINENCES?

Observations in the 171 A channel of the Atmospheric Imaging Assembly of the space-borne Solar Dynamics Observatory show tornado-like features in the atmosphere of the Sun. These giant tornadoes appear as dark, elongated, and apparently rotating structures in front of a brighter background. This phenomenon is thought to be produced by rotating magnetic field structures that extend throughout the atmosphere. We characterize giant tornadoes through a statistical analysis of properties such as spatial distribution, lifetimes, and sizes. A total number of 201 giant tornadoes are detected in a period of 25 days, suggesting that, on average, about 30 events are present across the whole Sun at a time close to solar maximum. Most tornadoes appear in groups and seem to form the legs of prominences, thus serving as plasma sources/sinks. Additional H{alpha} observations with the Swedish 1 m Solar Telescope imply that giant tornadoes rotate as a structure, although they clearly exhibit a thread-like structure. We observe tornado groups that grow prior to the eruption of the connected prominence. The rotation of the tornadoes may progressively twist the magnetic structure of the prominence until it becomes unstable and erupts. Finally, we investigate the potential relation of giant tornadoes to other phenomena, which may also be produced by rotating magnetic field structures. A comparison to cyclones, magnetic tornadoes, and spicules implies that such events are more abundant and short-lived the smaller they are. This comparison might help to construct a power law for the effective atmospheric heating contribution as a function of spatial scale.

79 ASTRONOMY AND ASTROPHYSICS↗

Gapless spin liquid and pair density wave of the Hubbard model on three-leg triangular cylinders

We study the ground state properties of the Hubbard model on three-leg triangular cylinders using large-scale density-matrix renormalization group simulations. At half-filling, we identify an intermediate gapless spin liquid phase, which has one gapless spin mode and algebraic spin–spin correlations but exponential decay scalar chiral–chiral correlations, between a metallic phase at weak coupling and Mott insulating dimer phase at strong interaction. Upon light doping the gapless spin liquid, the system exhibits power-law charge-density-wave (CDW) correlations but short-range single-particle, spin–spin, and chiral–chiral correlations. Similar to CDW correlations, the superconducting correlations also decay in power-law but oscillate in sign as a function of distance, which is consistent with the striped pair-density wave. When further doping the gapless spin liquid phase or doping the dimer order phase, another phase takes over, which has similar CDW correlations but all other correlations decay exponentially.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

EURADOS INTERCOMPARISON ON MEASUREMENTS AND MONTE CARLO MODELLING FOR THE ASSESSMENT OF AMERICIUM IN A USTUR LEG PHANTOM

United States Transuranium and Uranium Registries (USTUR) Case 0102 was the first whole-body donation to the USTUR (1979), of a worker affected by a substantial accidental 241Am intake(1). Half of this man’s skeleton, encased in tissue-quivalent plastic, provides a unique human ‘phantom’ for calibrating in vivo counting systems. In this case, the 241Am skeletal activity was measured 25 y after the intake. Approximately 82 % of the 241Am remaining in the body was found in the bones and teeth. The241Am activity concentration throughout the skeleton (in all types of bone) was fairly uniform(2). A protocol has been proposed by a group of in vivo laboratories from Europe [CIEMAT-Spain, IRSN-France and Helmholtz Zentrum Mu¨nchen (HMGU)-Germany] and Canada (HML) participating in this DOS/USTUR intercomparison. The focus areas for the study included: (1) the efficiency pattern along the leg phantom using Germanium detectors (experimental and computational), (2) the comparison of Monte Carlo (MC) results with experimental values in counting efficiency data and (3) the inflence of americium distribution in the bone material (volume or surface).

61 RADIATION PROTECTION AND DOSIMETRY↗

Metal to Wigner-Mott insulator transition in two-leg ladders

Here we study theoretically the quantum phase transition from a metal to a Wigner-Mott insulator at fractional commensurate filling on a two-leg ladder. We show that a continuous transition out of a symmetry-preserving Luttinger liquid metal is possible where the onset of insulating behavior is accompanied by the breaking of the lattice translation symmetry. At fillings $v$=1/$m$ per spin per unit cell, we find that the spin degrees of freedom also acquire a gap at the Wigner-Mott transition for odd integer $m$. In contrast for even integer $m$, the spin sector remains gapless and the resulting insulator is a ladder analog of the two-dimensional spinon surface state. In both cases, a charge neutral spinless mode remains gapless across the Wigner-Mott transition. We discuss physical properties of these transitions and comment on insights obtained for thinking about continuous Wigner-Mott transitions in two-dimensional systems which are being studied in moire materials.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Pair density wave in the doped three-band Hubbard model on two-leg square cylinders

A pair density wave (PDW) is a superconducting (SC) state with a spatially modulated order parameter. Although much is known about the properties of the PDW state, its realization in microscopic models with divergent susceptibility has been challenging. Here, in this work, we report a density-matrix renormalization group study of a three-band Hubbard model (also known as the Emery model) for cuprates on long two-leg square cylinders. Upon light doping, we find that the ground state of the system is consistent with that of a PDW state with mutually commensurate and power-law SC, charge (CDW), and spin (SDW) density wave correlations. The SC correlations are dominant between neighboring Cu sites with d-wave pairing symmetry. Interestingly, we find that the near-neighbor interactions, especially the near-neighbor attractive V pd interaction between neighboring Cu and oxygen sites, can notably enhance the SC correlations while simultaneously suppressing the CDW correlations. For a modestly strong attractive V pd , the SC correlations become quasi-long-ranged with a divergent PDW susceptibility.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗