Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “JuMP model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1936

Tank Tests of a Model of the NC Flying-boat Hull - N.A.C.A. Model 44

A 1/7.06 full-size model of the NC-type hull was tested in the N.A.C.A. tank by both the general method and the specific or free-to-trim method. The results of the tests are given in curves plotted as non dimensional coefficients and are compared with the test results of N.A.C.A. model 11-A. The NC model (N.A.C.A. model 44) shows higher resistance than model 11-A at hump speed but lower resistance at high speeds. Model 44 has a higher best trim angle at the jump and a lower maximum positive trimming moment than model 11-A. At high speeds the best trim angle and the trimming moments of the two models are approximately the same.

Bell, Joe W↗
NASA NTRS1976

An improved method for the prediction of completely three-dimensional aerodynamic load distributions of configurations with leading edge vortex separation

The application of a higher-order subsonic potential flow panel method to the solution of three-dimensional flow about wing and wing-body combinations with leading-edge vortex separation is presented. The governing equations are the linear flow differential equation and nonlinear boundary conditions which require that the flow be parallel to the wing and body surfaces and that the free vortex sheet, springing from the leading and trailing edges, be aligned with the local flow and support no pressure jump. The vortex core is modeled as a simple line vortex which receives vorticity from the free sheet through a connecting sheet. The Kutta condition is imposed on all appropriate edges of the wing. This set of nonlinear equations is solved by an iterative procedure. The Goethert rule accounts for compressibility. The method has been programmed for the CDC 6600. Delta wings, gothic wings, arrow wings, cambered wings, and wing with body have been analyzed. Initial studies involving variations of panel density, vortex sheet sizing, Jacobian update, and initial geometry demonstrate that the present method generally exhibits good convergence characteristics.

Rubbert, p. E.↗
NASA NTRS1990

Panel methods: An introduction

Panel methods are numerical schemes for solving (the Prandtl-Glauert equation) for linear, inviscid, irrotational flow about aircraft flying at subsonic or supersonic speeds. The tools at the panel-method user's disposal are (1) surface panels of source-doublet-vorticity distributions that can represent nearly arbitrary geometry, and (2) extremely versatile boundary condition capabilities that can frequently be used for creative modeling. Panel-method capabilities and limitations, basic concepts common to all panel-method codes, different choices that were made in the implementation of these concepts into working computer programs, and various modeling techniques involving boundary conditions, jump properties, and trailing wakes are discussed. An approach for extending the method to nonlinear transonic flow is also presented. Three appendices supplement the main test. In appendix 1, additional detail is provided on how the basic concepts are implemented into a specific computer program (PANAIR). In appendix 2, it is shown how to evaluate analytically the fundamental surface integral that arises in the expressions for influence-coefficients, and evaluate its jump property. In appendix 3, a simple example is used to illustrate the so-called finite part of the improper integrals.

Erickson, Larry L.↗
NASA NTRS2003

Closed-Loop Performance Measures for Flight Controllers Subject to Neutron-Induced Upsets

It has been observed that atmospheric neutrons can produce single event upsets in digital flight control hardware. The phenomenon has been studied extensively at the chip level, and now system level experiments are underway. In this paper analytical closed-loop performance measures for the tracking error are developed for a plant that is stabilized by a recoverable computer system subject to neutron induced upsets. The underlying model is a Markov jump-linear system with process noise. The steady-state tracking error is expressed in terms of a generalized observability Gramian.

Gray, W. Steven↗
NASA NTRS1991

Heat-pipe transient model for space applications

A two-dimensional model is developed for simulating heat pipes transient performance following changes in the input/rejection power or in the evaporator/condenser temperatures. The model employs the complete form of governing equations and momentum and energy jump conditions at the liquid-vapor interface. Although the model is capable of handling both cylindrical and rectangular geometries, the results reported are for a circular heat pipe with liquid lithium as the working fluid. The model incorporates a variety of other working fluids, such as water, ammonia, potassium, sodium and mercury, and offers combinations of isothermal, isoflux, convective and radiative heating/cooling conditions in the evaporator and condenser regions of the heat pipe. Results presented are for lithium heat pipes with exponential heating of the evaporator and isothermal cooling of the condenser.

Tournier, Jean-Michel↗
NASA NTRS1988

Calculation of unsteady Euler flows in turbomachinery using the linearized Euler equations

The model used by the present unsteady cascade flow calculation method is based on the linearized unsteady Euler equations and accounts for blade loading and geometry, shock motion, and wake motion. The steady flow that must be determined prior to the unsteady flow is ascertained by means of a Newton iteration procedure. A noteworthy feature of the procedure is the use of shock-fitting to determine steady and unsteady shock positions; the use of the Euler equations in conjunction with the Rankine-Hugoniot shock-jump conditions is found to directly model the generation of entropy and vorticity at shocks. Results are presented for both channel and cascade flows.

Hall, Kenneth C.↗
NASA NTRS1990

Linear evolution of current sheets in sheared force-free magnetic fields with discontinuous connectivity

Thin current sheets arising in tenuous, magnetized solar coronal plasmas may constitute an important mechanism for energy buildups and subsequent energy releases; they could arise from the continuous-and-random motion of magnetic footprints associated with photospheric velocity fields. A model is presented for study of the quasi-static evolution of current sheets due to shearing of the footpoints, in a highly idealized geometry that incorporates an abrupt jump in field-line connectivity. The model highlights that formation of thin current layers and allows large shearing motions prior to violation of the linear approximation. Excess energy comparable to that released by solar flares can be stored in a sheared field.

Wolfson, Richard↗
NASA NTRS1990

Interaction of minor ions with fast and slow shocks

The coronal slow shock was predicted to exist embedded in large coronal holes at 4 to 10 solar radii. A three-fluid model was used to study the jumps in minor ions propertes across the coronal slow shock. The jump conditions were formulated in the de Hoffmann-Teller frame of reference. The Rankine-Hugoniot solution determines the MHD flow and the magnetic field across the shocks. For each minor ion species, the fluid equations for the conservation of mass, momentum, and energy can be solved to determine the velocity and the temperature of the ions across the shock. A simularity solution was also obtained for heavy ions. The results show that on the downstream side of the coronal slow shock the ion temperatures are nearly proportional to the ion masses for He, O, Si, and Fe in agreement with observed ion temperatures in the inner solar wind. This indicates that the possibly existing coronal slow shock can be responsible for the observed heating of minor ions in the solar wind.

Whang, Y. C.↗
NASA NTRS1990

Heating of minor ions by the coronal slow shock

The coronal slow shock has been predicted to exist embedded in large coronal holes at 4-10 solar radii. In this paper, a three-fluid model is used to study the jumps in minor ion properties across a slow shock such as the coronal slow shock. The jump conditions are formulated in the de Hoffmann-Teller frame of reference. The Rankine-Hugoniot solution determines the MHD flow and the magnetic field across the shocks. For each minor ion species, the fluid equations for the conservation of mass, momentum, and energy can be solved to determine the velocity and the temperature of the ions across the shock. Also obtained is a similarity solution for heavy ions. The results show that, on the downstream side of the slow shock, the ion temperatures are nearly proportional to the ion masses for He, O, Si, and Fe, in agreement with observed ion temperatures in the inner solar wind. This indicates that the possibly existing coronal slow shock can be responsible for the observed heating of minor ions in the solar wind.

Whang, Y. C.↗
NASA NTRS1988

Muon motion in titanium hydride

Motional narrowing of the transverse-field muon spin rotation signal was observed in gamma-TiH(x) for x = 1.83, 1.97, and 1.99. An analysis of the data for TiH1.99 near room temperature indicates that the mechanism responsible for the motion of the muon out of the octahedral site is thermally activated diffusion with an attempt frequency comparable to the optical vibrations of the lattice. Monte Carlo calculations to simulate the effect of muon and proton motion upon the muon field-correlation time were used to interpret the motional narrowing in TiH1.97 near 500 K. The interpretation is dependent upon whether the Bloembergen, Purcell, and Pound (BPP) theory or an independent spin-pair relaxation model is used to obtain the vacancy jump rate from proton NMR T1 measurements. Use of BPP theory shows that the field-correction time can be obtained if the rate of motion of the muon with respect to the rate of the motion for the protons is decreased. An independent spin-pair relaxation model indicates that the field-correlation time can be obtained if the rate of motion for the nearest-neighbor protons is decreased.

Kempton, J. R.↗
NASA NTRS1999

Condensation of Forced Convection Two-Phase Flow in a Miniature Tube

A physical/mathematical model of annular film condensation at the inlet of a miniature tube has been developed. In the model, the liquid flow is coupled with the vapor flow along the liquid-vapor interface through the interfacial temperature, heat flux, shear stress, and pressure jump conditions due to surface tension effects. The model predicts the shape of the liquid-vapor interface along the condenser and leads to the conclusion that there is complete condensation at a certain distance from the condenser inlet. The numerical results show that complete condensation of the incoming vapor is possible at comparatively low heat loads and that this is a special case of a more general condensation regime with two-phase bubbly flow downstream of the initial annular film condensation region. Observations from the flow visualization experiment confirm the existence and qualitative features of annular film condensation leading to the complete condensation phenomenon in a small diameter (3.25 mm) circular tube condenser.

Begg, E.↗
NASA NTRSDate not supplied

Modeling and Simulation of Rotary Sloshing in Launch Vehicles

The nonlinear dynamics of propellant sloshing during orbital ascent are usually neglected in the flight control analysis of large boost vehicles under the assumption that the viscous damping of the fluid is sufficient to suppress nonlinear phenomena and confine the fluid to small, planar free surface displacements. In this case, the sloshing dynamics can be modeled using a spring-mass-damper or linearized pendulum mechanical analog. However, large, smooth-wall tanks without significant internal hardware or ring baffles are still susceptible to nonlinear effects. In particular, rotary sloshing can present a risk to flight control as it involves the formation of a stable limit cycle which can lead to undesirable roll coupling. The underlying phenomena of jump resonance does not manifest in linear models, but can be reproduced using a nonlinear spherical pendulum or the Bauer paraboloid model developed during the Apollo/Saturn program. In this paper, a detailed analysis of the rotary sloshing dynamics of these mechanical analogs is presented, and discussed in the context of flight control stability. High-fidelity simulations of a representative boost vehicle are used to verify the semi-analytical predictions of the nonlinear dynamic response.

Modeling↗
NASA NTRS1991

Electrostatic potential jump across fast-mode collisionless shocks

The electrostatic potential jump across fast-mode collisionless shocks is examined by comparing published observations, hybrid simulations, and a simple model, in order to better characterize its dependence on the various shock parameters. In all three, it is assumed that the electrons can be described by an isotropic power-law equation of state. The observations show that the cross-shock potential jump correlates well with the shock strength but shows very little correlation with other shock parameters. Assuming that the electrons obey an isotropic power law equation of state, the correlation of the potential jump with the shock strength follows naturally from the increased shock compression and an apparent dependence of the power law exponent on the Mach number which the observations indicate. It is found that including a Mach number dependence for the power law exponent in the electron equation of state in the simple model produces a potential jump which better fits the observations. On the basis of the simulation results and theoretical estimates of the cross-shock potential, it is discussed how the cross-shock potential might be expected to depend on the other shock parameters.

Mandt, M. E.↗
NASA NTRS1992

The Hubble Space Telescope observations of X-ray nova Muscae 1991 and its spectral evolution

Hubble Space Telescope Faint Object Spectrograph (FOS) Faint Object Camera (FOC) and observations of Nova Muscae 1991 obtained on May 14-15, 1991 are presented and discussed. A nearly featureless continuum with broad 2200 A absorption feature and no Balmer jump is found. The FOS spectrum is modeled, including previous multiepoch IUE, optical, and X-ray data using a simple blackbody accretion disk model. It is found that the mass transfer rate decays exponentially with a characteristic time of about 43 days. The cooling front predicted by the disk instability model should have been observable, but was not seen.

Cheng, F. H.↗
NASA NTRS1993

Ultraviolet spectropolarimetry of the Be star PP Carinae with the Wisconsin Ultraviolet Photo-Polarimeter Experiment

We present the first ultraviolet spectropolarimetric observations of the Be star PP Car, obtained with the Wisconsin Ultraviolet Photo-Polarimeter Experiment (WUPPE) aboard the Astro 1 mission. Usable polarization data were obtained from 1400 to 2330 A, along with a good spectrum from 1400 to 3200 A. These data show a lower polarization shortward of the Balmer jump than had been predicted by standard models, and a broad UV polarization dip around 1900 A is seen. These results are in agreement with those found from the WUPPE observations of two other Be stars, Xi Tau and Pi Aqr, which were published earlier. All these observations are an important probe of the Be circumstellar envelopes and demonstrate the need for the inclusion of metal-line effects in circumstellar disk models of Be star UV polarization.

Bjorkman, K. S.↗
NASA NTRS2017

The Effect of Entrainment Through Atmospheric Boundary Layer Growth on Observed and Modeled Surface Ozone in the Colorado Front Range

Ozone concentrations at the Earth's surface are controlled by meteorological and chemical processes and are a function of advection, entrainment, deposition, and net chemical production/loss. The relative contributions of these processes vary in time and space. Understanding the relative importance of these processes controlling surface ozone concentrations is an essential component for designing effective regulatory strategies. Here we focus on the diurnal cycle of entrainment through atmospheric boundary layer (ABL) growth in the Colorado Front Range. Aircraft soundings and surface observations collected in July/August 2014 during the DISCOVER-AQ/FRAPPÉ (Deriving Information on Surface conditions from Column and Vertically Resolved Observations Relevant to Air Quality/Front Range Air Pollution and Photochemistry Éxperiment) campaigns and equivalent data simulated by a regional chemical transport model are analyzed. Entrainment through ABL growth is most important in the early morning, fumigating the surface at a rate of ~5 ppbv/h. The fumigation effect weakens near noon and changes sign to become a small dilution effect in the afternoon on the order of -1 ppbv/h. The chemical transport model WRF-Chem (Weather Research and Forecasting Model with chemistry) underestimates ozone at all altitudes during this study on the order of 10-15 ppbv. The entrainment through ABL growth is overestimated by the model in the order of 0.6-0.8 ppbv/h. This results from differences in boundary layer growth in the morning and ozone concentration jump across the ABL top in the afternoon. This implicates stronger modeled fumigation in the morning and weaker modeled dilution after 11:00 LT.

Entrainment through ABL Growth↗
NASA NTRS2003

Mode Jumping of an Isogrid Panel Under Quasi-Static Compression

A wide column test of a composite isogrid panel subjected to quasi-static, axial compression is modeled with a hybrid-static dynamic computational method. The data from the test panel exhibited discontinuous responses in the compressive load for slowly increased end-shortening. The computational model was developed to corroborate these discontinuities with the phenomenon of mode jumping. Mode jumping refers to the transient response of the panel from an unstable bifurcation point on a postbuckled equilibrium path to a second stable equilibrium state on a new equilibrium path. On the new equilibrium path, both the analysis and test show that the panel can resist increased endshortening beyond that of the unstable critical point. Fair agreement is achieved between the analysis and test.

Muheim, Danniella M.↗
NASA NTRS2016

A Continuum Damage Mechanics Model to Predict Kink-Band Propagation Using Deformation Gradient Tensor Decomposition

A new model is proposed that represents the kinematics of kink-band formation and propagation within the framework of a mesoscale continuum damage mechanics (CDM) model. The model uses the recently proposed deformation gradient decomposition approach to represent a kink band as a displacement jump via a cohesive interface that is embedded in an elastic bulk material. The model is capable of representing the combination of matrix failure in the frame of a misaligned fiber and instability due to shear nonlinearity. In contrast to conventional linear or bilinear strain softening laws used in most mesoscale CDM models for longitudinal compression, the constitutive response of the proposed model includes features predicted by detailed micromechanical models. These features include: 1) the rotational kinematics of the kink band, 2) an instability when the peak load is reached, and 3) a nonzero plateau stress under large strains.

Bergan, Andrew C.↗