Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “JET THRUST”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Interference effects of aft reaction-control yaw jets on the aerodynamic characteristics of a space shuttle orbiter model at supersonic speeds

A wind tunnel investigation of the interference effects of aft reaction control system yaw jet plumes on a 0.0125 scale Space Shuttle orbiter model was conducted at Mach numbers from 2.50 to 4.50. Test variables included model angle of attack, model angle of sideslip, jet to free stream mass flow ratio, and number and position of operating jets. The aft reaction control jet plume creates a blockage above and behind the wing on the side in which the jet exhausts and results in flow separation on the wing upper surface and fuselage side. Positive pitching moment and side force increments and negative yawing moment and rolling moment increments due to the flow separations are incurred for left side firing jets, primarily at angles of attack above 10 deg. The yawing moment interference increments are favorable and result in a small jet thrust amplification. As a result of this investigation, the aft reaction control system was certified for operation at supersonic Mach numbers prior to the first flight of the space transportation system (STS-1).

Covell, P. F.↗
NASA NTRS1983

Status report - DARPA/NASA convertible turbofan/turboshaft engine program

A development status report is presented for the NASA/Defense Advanced Research Projects Agency convertible turbofan-turboshaft engine, which can power a high speed rotorcraft in vertical flight, as well as in horizontal flight up to speeds of Mach 0.85. The basis for this development program is a modified TF34-GE-400 engine. Program objectives include both the demonstration of dual output mode (jet thrust and shaft horsepower) capability and the development of a control system which will operate the engine in either mode and convert operation between the modes.

Bellin, A. I.↗
NASA NTRS1990

Exploration of planetesimals by a tripartite tethered spacecraft

Asteroids and comets exert such a small gravitational force that it is not practical to survey them from orbit. One must instead continuously accelerate using maneuvering rockets to move around the surface. A space exploration craft in three parts connected by lightweight cables can survey asteroids and comets, and deploy landers, without requiring the large thrusters and the continuous depletion of fuel required by a single craft. The spacecraft is deployed by spinning up from a compact configuration using low thrust jets, and then maintain surveying orbit without any major expenditure of energy. The triangular tether arrangement is stable, but care must be taken in changing orbits and with deploying and recovering samples, as can be demonstrated with a simple simulation. Even 100 km long tethers occupy a low payload fraction.

Stephens, Richard B.↗
NASA NTRS1948

Natural icing of an axial-flow turbojet engine in flight for a single icing condition

An investigation has been conducted in natural icing conditions to determine the effect of ice formations on the performance of an axial-flow turbojet engine. One flight was made in an icing condition in which the liquid-water content varied from 0.077 to 0.490 gram per cubic meter and the average droplet size varied from 5.4 to 12.1 microns. During a period of 60 minutes in icing, at an engine speed of 11,000 rpm, the tail-pipe temperature increased from 865 degrees to 965 degrees F. and the jet thrust decreased from 1950 to 1700 pounds. Near the end of the icing period, the engine was satisfactorily accelerated to take-off power.

Acker, Loren W↗
NASA NTRS1950

Effects of Inlet Icing on Performance of Axial-flow Turbojet Engine in Natural Icing Conditions

A flight investigation in natural icing conditions was conducted to determine the effect of inlet ice formations on the performance of axial-flow turbojet engines. The results are presented for icing conditions ranging from a liquid-water content of 0.1 to 0.9 gram per cubic meter and water-droplet size from 10 to 27 microns at ambient-air temperature from 13 to 26 degrees F. The data show time histories of jet thrust, air flow, tail-pipe temperature, compressor efficiency, and icing parameters for each icing encounter. The effect of inlet-guide-vane icing was isolated and shown to account for approximately one-half the total reduction in performance caused by inlet icing.

COMPRESSORS - AXIAL FLOW↗
NASA NTRS1956

Effect of an Adjustable Supersonic Inlet on the Performance up to Mach Number 2.0 of a J34 Turbojet Engine

A J34 turbojet engine was investigated at free-stream Mach numbers of 0.12 and 1.6 to 2.0 to determine the effect of supersonic inlet operation on engine performance. With the excepetion of ideal jet thrust, the use of generalized engine parameters correlated the engine data satisfactorily when the exit nozzle was choked. Large total-pressure distortations did not affect compressor efficiency. During inlet pulsing, the engine operated with compressor-inlet total-pressure variations as large as 18 percent of the local average and at frequnecies of 17 plus or minus 2 cycles per second. Total-pressure amplitudes propagated through the engine and caused ideal-gross-thrust changes up to 12 percent.

Beke, Andrew↗
NASA NTRS1996

AV-95 Sun Devil: High-Speed Military Rotorcraft

The AV-95 Sun Devil must combine helicopter capabilities, such as vertical takeoff and landings (VTOL) and rotor-powered flight, along with long-duration cruise and high-speed dash capabilities unobtainable by conventional helicopters. To be able to perform both tasks, and perform them well, the AV-95 Sun Devil design incorporates several unconventional devices; the AV-95 uses two convertible turbofan engines, able to provide both shaft power for the main rotor and tall fan as well as jet thrust either separately or simultaneously. Other devices used for the AV-95 include a variable diameter main rotor and a blown flap. In helicopter mode, the AV-95 Sun Devil performs like a winged helicopter. The addition of wings to an attack helicopter results in two significant advantages. First, the addition of wings makes a helicopter more maneuverable than a wingless, but otherwise similar helicopter. Second, since the wings produce lift, rotor stall and compressibility effects can be significantly delayed at high tip velocities. In fixed-wing mode, the main rotor is completely off-loaded but slightly powered, and the rotor diameter has been minimized. The AV-95 Sun Devil has many advantages over other VTOL aircraft. The conversion process is simple and fast; conversion does not make the AV-95 vulnerable to enemy attack during conversion such as a tilt-wing or a tilt-rotor. Stop-rotor aircraft and a stowed rotor aircraft require heavy breaking of the rotor for conversion; this adds time for conversion and weight to the aircraft. Because the AV-95 never stops the rotor in flight, much weight is spared, and conversion is much simpler and faster.

Source record↗
NASA NTRS1961

Loads Induced on a Flat-Plate Wing by an Air Jet Exhausting Perpendicularly through the Wing and Normal to a Free-Stream Flow of Mach Number 2.0

Measurements were made of loads induced on a flat-plate wing by an air jet exhausting perpendicularly through the wing and normal to the free-stream flow.The investigation was conducted at a free-stream Mach number of 2.0 and a Reynolds number per foot of 14.4 x 10(exp 6). An axially symmetric sonic nozzle and two supersonic nozzles were employed for the jets. The supersonic nozzles consisted of an axially symmetric nozzle with exit Mach number of 3.44 and a two-dimensional nozzle with exit Mach number of 1.76. The ratio of nozzle total pressure to free-stream static pressure was varied from 20 to 110. Negative loads were induced on the flat-plate wing by all the jets. As the nozzle pressure ratio was increased the magnitude of interference loads due to jet thrust decreased. The chordwise center-of-pressure location generally moved toward the nozzle center line as the pressure ratio was increased.

Janos, Joseph J.↗
NASA NTRS1957

Preliminary Internal Performance Data for a Variable-Ejector Assembly on the XJ79-GE-1 Turbojet Engine: Afterburning Configurations - II

Internal performance of an XJ79-GE-1 variable ejector was experimentally determined with the primary nozzle in two representative after-burning positions. Jet-thrust and air-handling data were obtained in quiescent air for 4 selected ejector configurations over a wide range of secondary to primary airflow ratios and primary-nozzle pressure ratios. The experimental ejector data are presented in both graphical and tabulated form.

Bloomer, Harry E.↗
NASA NTRS1952

Altitude Investigation of Gas Temperature Distribution at Turbine of Three Similar Axial-Flow Turbojet Engines

An investigation of the effect of inlet pressure, corrected engine speed, and turbine temperature level on turbine-inlet gas temperature distributions was conducted on a J40-WE-6, interim J40-WE-6, and prototype J40-WE-8 turbojet engine in the altitude wind tunnel at the NAC.4 Lewis laboratory. The engines were investigated over a range of simulated pressure altitudes from 15,000 to 55,000 feet, flight Mach numbers from 0.12 to 0.64, and corrected engine speeds from 7198 to 8026 rpm, The gas temperature distribution at the turbine of the three engines over the range of operating conditions investigated was considered satisfactory from the standpoint of desired temperature distribution with one exception - the distribution for the J40-WE-6 engine indicated a trend with decreasing engine-inlet pressure for the temperature to exceed the desired in the region of the blade hub. Installation of a compressor-outlet mixer vane assembly remedied this undesirable temperature distribution, The experimental data have shown that turbine-inlet temperature distributions are influenced in the expected manner by changes in compressor-outlet pressure or mass-flow distribution and by changes in combustor hole-area distribution. The similarity between turbine-inlet and turbine-outlet temperature distribution indicated only a small shift in temperature distribution imposed by the turbine rotors. The attainable jet thrusts of the three engines were influenced in different degrees and directions by changes in temperature distributions with change in engine-inlet pressure. Inability to match the desired temperature distribution resulted, for the J40-WE-6 engine, in an 11-percent thrust loss based on an average turbine-inlet temperature of 1500 F at an engine-inlet pressure of 500 pounds per square foot absolute. Departure from the desired temperature distribution in the Slade tip region results, for the prototype J40-WE-8 engine, in an attainable thrust increase of 3 to 4 percent as compared with that obtained if tip-region temperature limitations were observed.

Prince, W.R.↗
NASA NTRS1948

Preliminary Results of Nene II Engine Altitude-chamber Performance Investigation: Altitude Performance using 18.00-inch-diameter Jet Nozzle - 3

An investigation is being conducted to determine the altitude performance characteristics of the Nene II engine and its components. The present paper presents the preliminary results obtained using jet nozzle 18.00 inches in diameter, with an area equal to 92.2 percent of the area of the standard jet nozzle for this engine. The experimental results presented are for conditions simulating altitudes from 20,000 to 60,000 feet and ram-pressure ratios from 1.1 to 3.5. These ram-pressure ratios correspond to flight Mach numbers between 0.374 and 1.466. Data obtained with the 18.00 inch-diameter jet nozzle and corrected to standard sea-level conditions showed substantially the same trends with altitude as the data previously obtained with an 18.75-inch-diameter nozzle and with an 18.41-inch-diameter nozzle. Jet thrust, air consumption, and fuel consumption, corrected to standard sea-level conditions, increased rapidly with increasing ram-pressure ratio. In general, corrected net thrust specific fuel consumption increased with increase in ram-pressure ratio. Corrected net thrust decreased with an increase in ram-pressure ratio at an engine speed of 8000 rpm. At corrected engine speeds between 8000 and 10,800 rpm, net thrust first decreased with an increase in ram-pressure ratio and then increased with further increase in ram pressure ratio; at corrected engine speeds above 10,800 rpm, net thrust increased continuously with increase in ram-pressure ratio. Tail-pipe temperature decreased with an increase in ram-pressure ratio.

Grey, Ralph E.↗
NASA NTRS1950

Preliminary Performance Data on Westinghouse Electronic Power Regulator Operating on J34-WE-32 Turbojet Engine in Altitude Wind Tunnel

The behavior of the Westinghouse electronic power regulator operating on a J34-WE-32 turbojet engine was investigated in the NACA Lewis altitude wind tunnel at the request of the Bureau of Aeronautics, Department of the Navy. The object of the program was to determine the, steady-state stability and transient characteristics of the engine under control at various altitudes and ram pressure ratios, without afterburning. Recordings of the response of the following parameters to step changes in power lever position throughout the available operating range of the engine were obtained; ram pressure ratio, compressor-discharge pressure, exhaust-nozzle area, engine speed, turbine-outlet temperature, fuel-valve position, jet thrust, air flow, turbine-discharge pressure, fuel flow, throttle position, and boost-pump pressure. Representative preliminary data showing the actual time response of these variables are presented. These data are presented in the form of reproductions of oscillographic traces.

Ketchum, James R.↗
NASA NTRS1933

Jet Propulsion with Special Reference to Thrust Augmenters

An investigation of the possibility of using thrust augmented jets as prime movers was carried out. The augmentation was to be effected by allowing the jet to mix with the surrounding air in the presence of bodies which deflect the air set in motion by the jet.

Schubauer, G B↗
NASA NTRS1997

An Experimental/Modeling Study of Jet Attachment during Counterflow Thrust Vectoring

Recent studies have shown the applicability of vectoring rectangular jets using asymmetrically applied counterflow in the presence of a short collar. This novel concept has applications in the aerospace industry where counterflow can be used to vector the thrust of a jet's exhaust, shortening take-off and landing distances and enhancing in-flight maneuverability of the aircraft. Counterflow thrust vectoring, 'CFTV' is desirable due to its fast time response, low thrust loss, and absence of moving parts. However, implementation of a CFTV system is only possible if bistable jet attachment can be prevented. This can be achieved by properly designing the geometry of the collar. An analytical model is developed herein to predict the conditions under which a two-dimensional jet will attach to an offset curved wall. Results from this model are then compared with experiment; for various jet exit Mach numbers, collar offset distances, and radii of curvature. Their excellent correlation permits use of the model as a tool for designing a CFTV system.

Strykowski, Paul J.↗
NASA NTRS1979

An investigation of corner separation within a thrust augmenter having Coanda jets

The development of separation in corners of thrust augmentor wings having Coanda jets was investigated using hot film surface sensors and pressure transducers. Separation on the test augmentor began at a corner very close to the augmentor exit and then rapidly proceeded upstream. Measurements of the pressure fields in the corner region indicated that a modified form of the Stratford criterion could be used to predict the onset of separation. Testing was conducted over a range of nozzle pressure ratios, aspect ratios, diffuser angles, and designs of the boundary layer and Coanda nozzles.

Seiler, M. R.↗