Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Iridium oxide catalyst”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Probing the active sites of oxide encapsulated electrocatalysts with controllable oxygen evolution selectivity

Electrocatalysts encapsulated by nanoscopic overlayers can control the rate of redox reactions at the outer surface of the overlayer or at the buried interface between the overlayer and the active catalyst, leading to complex behavior in the presence of two competing electrochemical reactions. This study investigated oxide encapsulated electrocatalysts (OECs) comprised of iridium (Ir) thin films coated with an ultrathin (2–10 nm thick) silicon oxide (SiO x ) or titanium oxide (TiO x ) overlayer. The performance of SiO x |Ir and TiO x |Ir thin film electrodes towards the oxygen evolution reaction (OER) and Fe(II)/Fe(III) redox reactions were evaluated. An improvement in selectivity towards the OER was observed for all OECs. Overlayer properties, namely ionic and electronic conductivity, were assessed using a combination of electroanalytical methods and molecular dynamics simulations. SiO x and TiO x overlayers were found to be permeable to H 2 O and O 2 such that the OER can occur at the MO x |Ir (M = Ti, Si) buried interface, which was further supported with molecular dynamics simulations of model SiO 2 coatings. In contrast, Fe(II)/Fe(III) redox reactions occur to the same degree with TiO x overlayers having thicknesses less than 4 nm as bare electrocatalyst, while SiO x overlayers inhibit redox reactions at all thicknesses. This observation is attributed to differences in electronic transport between the buried interface and outer overlayer surface, as measured with through-plane conductivity measurements of wetted overlayer materials. These findings reveal the influence of oxide overlayer properties on the activity and selectivity of OECs and suggest opportunities to tune these properties for a wide range of electrochemical reactions.

08 HYDROGEN↗
DOE OSTI2023

Multielectrode electrochemical cell for in situ structural characterization of amorphous thin-film catalysts using high-energy X-ray scattering

A multielectrode-based electrochemical cell allows the structural characterization of an amorphous thin-film water oxidation catalyst under various electrochemical potentials using high-energy X-ray scattering and atomic pair distribution function (PDF) techniques. A multielectrode with five electrodes provides a sufficiently low background signal to enable high-energy X-ray scattering (HEXS) measurements and amplifies the extremely low HEXS signals from samples for high-resolution PDF analysis of in situ data from thin-film catalysts. Glassy carbon (GC) creates a relatively low intensity HEXS pattern and is used as a working electrode. Instead of a three-dimensional (3D) porous electrode architecture, the flat geometry of the electrode enables various deposition techniques to be used for the preparation of a highly conductive metal oxide layer. PDF analysis demonstrates high spatial resolution for a 230 nm thick amorphous iridium oxide film deposited on two roughened 60 µm thick GC electrodes. The PDF analysis resolves the domain size and distinguishes changes in fine structure which are directly correlated with the structure and function of the catalysts. In conclusion, the results bring the opportunity to analyze the structure of nanometre-scale amorphous thin-film catalysts in an electrolyte-compatible and compact 3D-printed electrochemical cell in a three-electrode configuration.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Electrolyzer Performance Loss from Accelerated Stress Tests and Corresponding Changes to Catalyst Layers and Interfaces

Stress tests are developed for proton exchange membrane electrolyzers that utilize low catalyst loading, elevated potential, and frequent cycling with square- and triangle-waves to accelerate anode catalyst layer degradation during intermittent operation. Kinetics drive performance losses (ohmic/transport secondary) and are accompanied by decreasing exchange current density, decreasing cyclic voltammetric capacitance, and increasing polarization resistance. Decreased kinetics are likely due to a combination of iridium (Ir) migration into electrochemically inaccessible locations in the anode or membrane, Ir particle growth (supported by X-ray scattering), changes in the extent of the Ir oxidation state (supported by X-ray absorption spectroscopy), and anode catalyst layer reordering. Decreasing catalyst/transport layer contact and catalyst/membrane interfacial tearing may add contact resistances and account for increasing ohmic losses. Performance losses for low and moderate catalyst loading, as well as from accelerated and model wind/solar cycling protocols, were likewise dominated by kinetics but vary in severity. Additionally, accelerated cycling (1 cycle per minute) appears to reasonably accelerate relevant loss mechanisms and can be used to project electrolyzer lifetime from anode deterioration. Ongoing accelerated stress test development and studies into performance loss mechanisms will continue to be critical as electrolysis shifts to intermittent power and low-cost applications.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2025

Strong Coupling of Iridium and Boron–Carbon-Nitride Support for Enhanced Acidic Water Oxidation

Supporting iridium (Ir)-based materials on stable and suitable substrates is an efficient strategy to improve their catalytic performance for the oxygen evolution reaction (OER) in harsh acidic environments. Herein, we report a series of Ir catalysts supported on boron–carbon-nitride (BCN), denoted as Ir/BCN. Detailed experiments combined with density functional theory calculations demonstrate strong interactions between Ir nanoparticles (NPs) and the BCN support, significantly contributing to the improved OER performance. Among the synthesized catalysts, the Ir/BCN-75 catalyst outperforms commercial Ir black and IrO 2 in both half-cell and proton exchange membrane water electrolysis (PEMWE) tests. Specially, the Ir/BCN-75 catalyst achieves a high current density of 2.94 A cm –2 at 1.9 V with a low Ir loading of 0.26 mg cm –2 in PEMWE measurements, exceeding most Ir-based catalysts reported to date. The BCN support interacts strongly with Ir, wherein Ir–N bonding directs the Ir NP growth and enhances electrocatalytic activity, while Ir–B bonding contributes to the stability of the Ir/BCN catalyst.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Increasing Iridium Oxide Activity for the Oxygen Evolution Reaction with Hafnium Modification

Synthesis and implementation of highly active, stable, and affordable electrocatalysts for the oxygen evolution reaction (OER) is a major challenge in developing energy efficient and economically viable energy conversion devices such as electrolyzers, rechargeable metal-air batteries, and regenerative fuel cells. The current benchmark electrocatalyst for OER is based on iridium oxide (IrO x ) due to its superior performance and excellent stability. However, large scale applications using IrO x are impractical due to its low abundance and high cost. In this work, we report a highly active hafnium-modified iridium oxide (IrHf x O y ) electrocatalyst for OER. The IrHf x O y electrocatalyst demonstrated ten times higher activity in alkaline conditions (pH = 11) and four times higher activity in acid conditions (pH = 1) than a IrO x electrocatalyst. The highest intrinsic mass activity of the IrHf x O y catalyst in acid conditions was calculated as 6950 A gIrO x -1 at an overpotential (η) of 0.3 V. Combined studies utilizing operando surface enhanced Raman spectroscopy (SERS) and DFT calculations revealed that the active sites for OER are the Ir-O species for both IrO x and IrHf x O y catalysts. The presence of Hf sites leads to more negative charge states on nearby O sites, and shortening the bond lengths of Ir-O, and lowering free energies for OER intermediates to accelerate the OER process.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Non-noble metal based electro-catalyst compositions for proton exchange membrane based water electrolysis and methods of making

The invention provides electro-catalyst compositions for an anode electrode of an acid mediated proton exchange membrane-based water electrolysis system. The compositions include a noble metal component selected from the group consisting of iridium oxide, ruthenium oxide, rhenium oxide and mixtures thereof, and a non-noble metal component selected from the group consisting of tantalum oxide, tin oxide, niobium oxide, titanium oxide, tungsten oxide, molybdenum oxide, yttrium oxide, scandium oxide, cooper oxide, zirconium oxide, nickel oxide and mixtures thereof. Further, the non-noble metal component can include a dopant. The dopant can be at least one element selected from Groups III, V, VI and VII of the Periodic Table. The compositions can be prepared using any solution based methods involving a surfactant approach or a sol gel approach. Further, the compositions are prepared using noble metal and non-noble metal precursors. Furthermore, a thin film containing the compositions can be deposited onto a substrate to form the anode electrode.

Kumta, Prashant N.↗
DOE OSTI2024

Ruthenium-lead oxide for acidic oxygen evolution reaction in proton exchange membrane water electrolysis

Developing an active and stable anode catalyst for the proton exchange membrane water electrolyzer (PEM-WE) is a critical objective to enhance the economic viability of green hydrogen technology. However, the expensive iridium-based electrocatalyst remains the sole practical material with industrial-level stability for the acidic oxygen evolution reaction (OER) at the anode. Ruthenium-based catalysts have been proposed as more cost-effective alternatives with improved activity, though their stability requires enhancement. The current urgent goal is to reduce costs and noble metal loading of the OER catalyst while maintaining robust activity and stability. Here, in this study, we design a Ru-based OER catalyst incorporating Pb as a supporting element. This electrocatalyst exhibits an OER overpotential of 201 mV at 10 mA.cm -2 , simultaneously reducing Ru noble metal loading by similar to 40%. Normalization of the electrochemically active surface area unveils improved intrinsic activity compared to the pristine RuO 2 catalyst. During a practical stability test in a PEM-WE setup, our developed catalyst sustains stable performance over 300 h without notable degradation, underscoring its potential for future applications as a reliable anodic catalyst.

Electrocatalysis↗
DOE OSTI2021

Organometallic complexes as preferred precursors to form molecular Ir(pyalk) coordination complexes for catalysis of oxygen evolution

Our previously reported ‘blue solution’ oxygen-evolution catalyst consists of an isomeric mixture of coordination complexes containing the (pyalk)Ir IV –O–Ir IV (pyalk) core unit and is thus entirely molecular but only when formed from organometallic precursors such as Cp*Ir(pyalk)Cl or Ir(pyalk)(CO) 2 (pyalk = (2-pyridyl)-2-propanolate). We now show that attempts to form it from such obvious coordination precursors as Na[Ir(pyalk)Cl 4 ] or Na[IrCl 2 (pyalk)(O 2 CPh) 2 ], under a variety of conditions, always fail in our hands, leading to a mixture of molecular ‘blue solution’ species and IrO x nanoparticles, rather than the purely homogeneous catalyst formed from organometallic precursors. The loss of the pyalk ligand during the oxidative activation is associated with the nanoparticle generation. External chelating ligands also failed to stop the nanoparticle formation. This work implies the paradoxical conclusion that organometallic complexes are effective as catalyst precursors, even when coordination complexes are the catalytically active species, since the inner-sphere organometallic ligands, although ultimately lost or degraded, may nevertheless have a stabilizing effect sufficient to suppress undesirable nanoparticle production pathways in the activation of the catalyst precursor. Finally, a key aspect of the present study is that organometallic complexes in general may be useful catalyst precursors even if the organometallic ligands are lost in the activation process.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Enhancing Acidic Oxygen Evolution Activity by Controlling Oxidation State of Iridium

Iridium oxides with high oxidation states have been reported to be effective in enhancing the acidic oxygen evolution reaction (OER) performance. Herein, we develop ultrasmall IrO x nanoparticles (NPs) over titanium nitride (TiN), which undergoes surface oxidation under oxidative conditions to form oxygen-modified TiN (oxi-TiN), enabling the formation of highly oxidized Ir δ+ (δ > 4). This IrO x /oxi-TiN catalyst delivers higher Ir mass activity than commercial IrO 2 , while comparable stability is maintained. The superior OER activity of IrO x /oxi-TiN is further demonstrated in a proton exchange membrane water electrolyzer (PEMWE), requiring only 1.88 V to reach 3 A cm −2 , achieving the U.S. Department of Energy 2025 target (1.90 V at 3 A cm −2 ). In situ X-ray absorption spectroscopy (XAS) confirms that the superior OER activity of IrO x /oxi-TiN originates from highly oxidized Ir δ+ under OER conditions. Further, density functional theory (DFT) calculations reveal a general correlation between the oxidation state of Ir and OER overpotential. Specifically, the introduction of interfacial oxygen at the Ir/TiN interface increases the oxidation state of deposited Ir δ+ from δ < 4 to δ > 4, decreasing the OER overpotential. This study highlights the critical role of high oxidation states of Ir δ+ in enhancing OER activity, providing guidance for the development of advanced acidic OER catalysts.

In situ measurements↗
NASA NTRS2000

Combinatorial Optimization of Heterogeneous Catalysts Used in the Growth of Carbon Nanotubes

Libraries of liquid-phase catalyst precursor solutions were printed onto iridium-coated silicon substrates and evaluated for their effectiveness in catalyzing the growth of multi-walled carbon nanotubes (MWNTs) by chemical vapor deposition (CVD). The catalyst precursor solutions were composed of inorganic salts and a removable tri-block copolymer (EO)20(PO)70(EO)20 (EO = ethylene oxide, PO = propylene oxide) structure-directing agent (SDA), dissolved in ethanol/methanol mixtures. Sample libraries were quickly assayed using scanning electron microscopy after CVD growth to identify active catalysts and CVD conditions. Composition libraries and focus libraries were then constructed around the active spots identified in the discovery libraries to understand how catalyst precursor composition affects the yield, density, and quality of the nanotubes. Successful implementation of combinatorial optimization methods in the development of highly active, carbon nanotube catalysts is demonstrated, as well as the identification of catalyst formulations that lead to varying densities and shapes of aligned nanotube towers.

Cassell, Alan M.↗
DOE OSTI2023

Degradation Effects at the Porous Transport Layer/Catalyst Layer Interface in Polymer Electrolyte Membrane Water Electrolyzer

The porous transport layer (PTL)/catalyst layer (CL) interface plays a crucial role in the achievement of high performance and efficiency in polymer electrolyte membrane water electrolyzers (PEMWEs). This study investigated the effects of the PTL/CL interface on the degradation of membrane electrode assemblies (MEAs) during a 4000 h test, comparing the MEAs assembled with uncoated and Ir-coated Ti PTLs. Our results show that compared to an uncoated PTL/CL interface, an optimized interface formed when using a platinum group metal (PGM) coating, i.e., an iridium layer at the PTL/CL interface, and reduced the degradation of the MEA. The agglomeration and formation of voids and cracks could be found for both MEAs after the long-term test, but the incorporation of an Ir coating on the PTL did not affect the morphology change or oxidation of IrO x in the catalyst layer. In addition, our studies suggest that the ionomer loss and restructuring of the anodic MEA can also be reduced by Ir coating of the PTL/CL interface. Optimization of the PTL/CL interface improves the performance and durability of a PEMWE.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2022

Highly stable preferential carbon monoxide oxidation by dinuclear heterogeneous catalysts

Atomically dispersed catalysts have been shown highly active for preferential oxidation of carbon monoxide in the presence of excess hydrogen (PROX). However, their stability has been less than ideal. We show here that the introduction of a structural component to minimize diffusion of the active metal center can greatly improve the stability without compromising the activity. Using an Ir dinuclear heterogeneous catalyst (DHC) as a study platform, we identify two types of oxygen species, interfacial and bridge, that work in concert to enable both activity and stability. In conclusion, the work sheds important light on the synergistic effect between the active metal center and the supporting substrate and may find broad applications for the use of atomically dispersed catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Enhancing Acidic Oxygen Evolution Activity by Controlling Oxidation State of Iridium

Iridium oxides with high oxidation states have been reported to be effective in enhancing the acidic oxygen evolution reaction (OER) performance. In this work, we develop ultrasmall IrO x nanoparticles (NPs) over titanium nitride (TiN), which undergoes surface oxidation under oxidative conditions to form oxygen‐modified TiN (oxi‐TiN), enabling the formation of highly oxidized Ir δ+ (δ > 4). This IrO x /oxi‐TiN catalyst delivers higher Ir mass activity than commercial IrO 2 , while comparable stability is maintained. The superior OER activity of IrO x /oxi‐TiN is further demonstrated in a proton exchange membrane water electrolyzer (PEMWE), requiring only 1.88 V to reach 3 A cm −2 , achieving the U.S. Department of Energy 2025 target (1.90 V at 3 A cm −2 ). In situ X‐ray absorption spectroscopy (XAS) confirms that the superior OER activity of IrO x /oxi‐TiN originates from highly oxidized Ir δ+ under OER conditions. Density functional theory (DFT) calculations reveal a general correlation between the oxidation state of Ir and OER overpotential. Specifically, the introduction of interfacial oxygen at the Ir/TiN interface increases the oxidation state of deposited Ir δ+ from δ < 4 to δ > 4, decreasing the OER overpotential. This study highlights the critical role of high oxidation states of Ir δ+ in enhancing OER activity, providing guidance for the development of advanced acidic OER catalysts.

58 GEOSCIENCES↗
DOE OSTI2024

Amorphous Iridium Oxide-Integrated Anode Electrodes with Ultrahigh Material Utilization for Hydrogen Production at Industrial Current Densities

Herein, ionomer-free amorphous iridium oxide (IrO x ) thin electrodes are first developed as highly active anodes for proton exchange membrane electrolyzer cells (PEMECs) via low-cost, environmentally friendly, and easily scalable electrodeposition at room temperature. Combined with a Nafion 117 membrane, the IrO x -integrated electrode with an ultralow loading of 0.075 mg cm –2 delivers a high cell efficiency of about 90%, achieving more than 96% catalyst savings and 42-fold higher catalyst utilization compared to commercial catalyst-coated membrane (2 mg cm –2 ). Additionally, the IrO x electrode demonstrates superior performance, higher catalyst utilization and significantly simplified fabrication with easy scalability compared with the most previously reported anodes. Notably, the remarkable performance could be mainly due to the amorphous phase property, sufficient Ir 3+ content, and rich surface hydroxide groups in catalysts. Overall, due to the high activity, high cell efficiency, an economical, greatly simplified and easily scalable fabrication process, and ultrahigh material utilization, the IrO x electrode shows great potential to be applied in industry and accelerates the commercialization of PEMECs and renewable energy evolution.

08 HYDROGEN↗
DOE OSTI2026

Enhancing Acidic Oxygen Evolution Activity by Supporting Iridium Electrocatalysts on Tantalum Carbide

For a high-performance proton exchange membrane water electrolyzer (PEMWE), acidic oxygen evolution reaction (OER) electrocatalysts require highly dispersed iridium oxide (IrO x ) nanoparticles. Although carbon-based materials have been explored as promising supports for IrO x nanoparticles, their limited stability under harsh oxidative and acidic PEMWE conditions remains a significant challenge. Here, in this study, we report the synthesis and in situ characterization of active and durable IrOx electrocatalysts supported on electrochemically stable and electrically conducting tantalum carbide (TaC). When applied in a PEMWE, the IrO x /TaC electrocatalyst achieves a cell voltage of 1.71 V at 1.0 A cm –2 , outperforming the commercial IrO 2 catalyst (1.82 V at 1.0 A cm –2 ). Furthermore, the IrO x /TaC catalyst maintains a stable operation for 200 h at 0.5 A cm –2 with a low degradation rate of 36 μV h –1 . Density functional theory calculations further confirm that Ir–O–Ta bond formation at the IrO x /TaC interface reduces the overpotential of the OER compared to IrO 2 . This study underscores the pivotal role of supporting IrO x over stable and conducting metal carbides, providing guidance for the design of advanced acidic OER catalysts.

58 GEOSCIENCES↗
DOE OSTI2022

Oxygen Evolution Reaction in Alkaline Environment: Material Challenges and Solutions

Abstract The oxygen evolution reaction (OER) generally exists in electrochemistry‐enabled applications that are coupled with cathodic reactions like hydrogen evolution, carbon dioxide reduction, ammonia synthesis, and electrocatalytic hydrogenation. The OER heavily impacts the overall energy efficiency of these devices because the sluggish OER kinetics result in a huge overpotential, thus, a large amount of efficient catalysts are needed. The benchmark iridium and ruthenium (Ir/Ru)‐based materials (mostly used in acid media) are, however, significantly limited by their scarcity. Non‐precious metal‐based catalysts (NPMCs) have emerged as the most promising alternatives; however, they tend to degrade quickly under the harsh operating conditions of typical OER devices. Another challenge is the unsatisfying performance of OER catalysts when integrated in real‐world devices. Herein, the OER active sites for three mainstream types of NPMCs including non‐precious transition metal oxides/(oxy)hydroxides, metal‐free carbon materials, and hybrid non‐precious metal and carbon composites are reviewed. In addition, possible degradation mechanisms for active sites and mitigation strategies are discussed in detail. This review also provides insights into the gaps between R&D of NPMCs for the OER and their applications in practical devices.

Xie, Xiaohong↗
DOE OSTI2024

Theoretical Prediction and Experimental Verification of IrO x Supported on Titanium Nitride for Acidic Oxygen Evolution Reaction

Reducing iridium (Ir) catalyst loading for acidic oxygen evolution reaction (OER) is a critical strategy for large-scale hydrogen production via proton exchange membrane (PEM) water electrolysis. However, simultaneously achieving high activity, long-term stability, and reduced material cost remains challenging. To address this challenge, we develop a frame-work by combining density functional theory (DFT) prediction using model surfaces and proof-of-concept experimental ver-ification using thin films and nanoparticles. DFT results predict that oxidized Ir monolayers over titanium nitride (IrO x /TiN) should display higher OER activity than IrO x while reducing Ir loading. Further, this prediction is verified by depositing Ir monolayers over TiN thin films via physical vapor deposition. The promising thin film results are then extended to commercially viable powder IrO x /TiN catalysts, which demonstrate a lower overpotential and higher mass activity than commercial IrO 2 , and a long-term stability of 250 hours to maintain a current density of 10 mA cm -2 . The superior OER performance of IrO x /TiN is further confirmed using proton exchange membrane water electrolyzer (PEMWE), which shows a lower cell voltage than commercial IrO 2 to achieve a current density of 1 A cm -2 . Both DFT and in situ X-ray absorption spectroscopy reveal that the high OER performance of IrO x /TiN strongly depends on the IrO x - TiN interaction via direct Ir-Ti bonding. This study highlights the importance of close interaction between theoretical prediction based on mechanistic understanding and experimental verification based on thin film model catalysts to facilitate the development of more practical powder IrO x /TiN catalysts with high activity and stability for acidic OER.

08 HYDROGEN↗