Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Interfacial tension”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Impacts of Pore Network-Scale Wettability Heterogeneity on Immiscible Fluid Displacement: A Micromodel Study

The mixed-wet nature of reservoir formations imposes a wide range of rock wettability from strong resident-fluid wetting to strong invading-fluid wetting. The characteristics of two-phase flow in porous media composed of mixed-wetting surfaces remain poorly understood. In this study, we investigated the displacement of resident ethylene glycol (EG) by hexane in two mixed-wet micromodels of identical 2.5-D geometry heterogeneity, with uniformly or heterogeneously distributed patches strongly wetting to hexane. These patches are mixed among pores with unaltered EG-wetting surfaces. Along with control tests in the originally EG-wet micromodel, here we show the classic fingering and transitions in flow regimes at $logCa$ (capillary number) from -7.2 to -3.9. Moreover, pore-scale distributions of wettability and their spatial correlation influence displacement efficiency. In the two mixed-wet micromodels, we found (a) an increase of steady-state hexane saturation at the end of experiments by up to 0.12 in the capillary fingering regime and a decrease of at most by 0.06 in the viscous fingering regime, compared to the EG-wet micromodel, and (b) dispersed and fragmented hexane distribution after displacement. Brine drainage during supercritical CO 2 (scCO 2 ) injections in these micromodels occurs with lower wettability contrasts, and under similar viscosity ratios and interfacial tensions resulted in higher displacement efficiency relative to displacement of EG by hexane. While mixed-wettability can enhance displacement efficiency compared to uniform wettability, the dynamics of immiscible fluids in strong mixed-wet reservoirs are expected to be less pronounced in contributing to the efficiency of geological CO 2 sequestration, oil recovery, and remediation of hydrocarbon-contaminated aquifers.

2.5-D micromodel↗
DOE OSTI2022

Entropically engineered formation of fivefold and icosahedral twinned clusters of colloidal shapes

Fivefold and icosahedral symmetries induced by multiply twinned crystal structures have been studied extensively for their role in influencing the shape of synthetic nanoparticles, and solution chemistry or geometric confinement are widely considered to be essential. Here we report the purely entropy-driven formation of fivefold and icosahedral twinned clusters of particles in molecular simulation without geometric confinement or chemistry. Hard truncated tetrahedra self-assemble into cubic or hexagonal diamond colloidal crystals depending on the amount of edge and vertex truncation. By engineering particle shape to achieve a negligible entropy difference between the two diamond phases, we show that the formation of the multiply twinned clusters is easily induced. The twinned clusters are entropically stabilized within a dense fluid by a strong fluid-crystal interfacial tension arising from strong entropic bonding. Our findings provide a strategy for engineering twinning behavior in colloidal systems with and without explicit bonding elements between particles.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Effects of grain size and small-scale bedform architecture on CO 2 saturation from buoyancy-driven flow

Small-scale (mm-dm scale) heterogeneity has been shown to significantly impact CO 2 migration and trapping. To investigate how and why different aspects of small-scale heterogeneity affect the amount of capillary trapping during buoyancy-driven upward migration of CO 2 , we conducted modified invasion percolation simulations on heterogeneous domains. Realistic simulation domains are constructed by varying two important aspects of small-scale geologic heterogeneity: sedimentary bedform architecture and grain size contrast between the matrix and the laminae facies. Buoyancy-driven flow simulation runs cover 59 bedform architecture and 40 grain size contrast cases. Simulation results show that the domain effective CO 2 saturation is strongly affected by both grain size and bedform architecture. At high grain size contrasts, bedforms with continuous ripple lamination at the cm scale tend to retain higher CO 2 saturation than bedforms with discontinuous or cross lamination. In addition, the “extremely well sorted” grain sorting cases tend to have lower CO 2 saturation than expected for cross-laminated domains. Finally, both a denser CO 2 phase and greater interfacial tension increase CO 2 saturation. Again, variation in fluid properties seems to have a greater effect on CO 2 saturation for cross-laminated domains. This result suggests that differences in bedform architecture can impact how CO 2 saturation values respond to other variables such as grain sorting and fluid properties.

58 GEOSCIENCES↗
DOE OSTI2020

Nano-layer deposition of metal oxides via a condensed water film

Abstract Nanocoatings on solids can be achieved by various processes, including sol-gel and atomic layer deposition. However, challenges remain for achieving uniform nanocoatings on nanoscale substrates at a large scale. Here, we report a versatile and fundamentally different technique, termed condensed layer deposition, for depositing conformal metal oxide nanocoatings on nanoparticles and nanofibers. This approach involves water in liquid hydrocarbons condensing as a nanoscale water film on the substrate surface, enabled by interfacial tension between polar water and nonpolar liquid hydrocarbons. Chemical precursors are then added, which react with the condensed water film to form a metal oxide nanocoating. We demonstrate this for titania, alumina, and niobia on substrates including carbon nanotubes, iron oxide particles and carbon black. Condensed layer deposition can achieve oxide nanocoatings on a variety of substrates with tunable thickness, in one pass, at room temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Shear-free mixing to achieve accurate temporospatial nanoscale kinetics through scanning-SAXS: ion-induced phase transition of dispersed cellulose nanocrystals

Time-resolved in situ characterization of well-defined mixing processes using small-angle X-ray scattering (SAXS) is usually challenging, especially if the process involves changes of material viscoelasticity. In specific, it can be difficult to create a continuous mixing experiment without shearing the material of interest; a desirable situation since shear flow both affects nanoscale structures and flow stability as well as resulting in unreliable time-resolved data. Here, we demonstrate a flow-focusing mixing device for in situ nanostructural characterization using scanning-SAXS. Given the interfacial tension and viscosity ratio between core and sheath fluids, the core material confined by sheath flows is completely detached from the walls and forms a zero-shear plug flow at the channel center, allowing for a trivial conversion of spatial coordinates to mixing times. With this technique, the time-resolved gel formation of dispersed cellulose nanocrystals (CNCs) was studied by mixing with a sodium chloride solution. It is observed how locally ordered regions, so called tactoids, are disrupted when the added monovalent ions affect the electrostatic interactions, which in turn leads to a loss of CNC alignment through enhanced rotary diffusion. The demonstrated flow-focusing scanning-SAXS technique can be used to unveil important kinetics during structural formation of nanocellulosic materials. However, the same technique is also applicable in many soft matter systems to provide new insights into the nanoscale dynamics during mixing.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Active motion of multiphase oil droplets: emergent dynamics of squirmers with evolving internal structure

Synthetic soft matter systems, when driven beyond equilibrium by active processes, offer the potential to achieve dynamical states and functions of a complexity found in living matter. Emulsions offer the basis of a simple yet versatile system for identification of the physicochemical principles underlying active soft matter, but how multiple internal phases within emulsion droplets (e.g., Janus morphologies) organize to impact emergent dynamics is not understood. Here, we create multiphase oil droplets with ultralow interfacial tensions but distinct viscosities, and drive them into motion in aqueous micellar solutions. Preferential solubilization of select components of the oil both drives the droplet motion and yields a progression of internal phase morphological states with distinct symmetries. In this work, we find the active droplets to exhibit five dynamical states during morphogenesis. By quantifying microscopic flow fields, we show that it is possible to map the diverse droplet behaviors to squirmer models of spherical microswimmers in Stokes flow, thus showing that multiphase droplets offer the basis of a versatile platform with which to study and engineer the hydrodynamics of microswimmers.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Insights into water extraction and aggregation mechanisms of malonamide-alkane mixtures

Structure at the nanoscale in the organic phase of liquid–liquid extraction systems is often tied to separation performance. However, the weak interactions that drive extractant assembly lead to poorly defined structures that are challenging to identify. Here, in this work, we investigate the mechanism of water extraction for a malonamide extractant commonly applied to f-element separations. We measure extractant concentration fluctuations in the organic phase with small angle X-ray scattering (SAXS) before and after contact with water at fine increments of extractant concentration, finding no qualitative changes upon water uptake that might suggest significant nanoscopic reorganization of the solution. The critical composition for maximum fluctuation intensity is consistent with small water–extractant adducts. The extractant concentration dependence of water extraction is consistent with a power law close to unity in the low concentration regime, suggesting the formation of 1 : 1 water–extractant adducts as the primary extraction mechanism at low concentration. At higher extractant concentrations, the power law slope increases slightly, which we find is consistent with activity effects modeled using Flory–Huggins theory without introduction of additional extractant–water species. Molecular dynamics simulations are consistent with these findings. The decrease in interfacial tension with increasing extractant concentration shows a narrow plateau region, but it is not correlated with any change in fluctuation or water extraction trends, further suggesting no supramolecular organization such as reverse micellization. This study suggests that water extraction in this system is particularly simple: it relies on a single mechanism at all extractant concentrations, and only slightly enhances the concentration fluctuations characteristic of the dry binary extractant/diluent mixture.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Hanging droplets from liquid surfaces

Natural and man-made robotic systems use the interfacial tension between two fluids to support dense objects on liquid surfaces. Here, we show that coacervate-encased droplets of an aqueous polymer solution can be hung from the surface of a less dense aqueous polymer solution using surface tension. The forces acting on and the shapes of the hanging droplets can be controlled. Sacs with homogeneous and heterogeneous surfaces are hung from the surface and, by capillary forces, form well-ordered arrays. Locomotion and rotation can be achieved by embedding magnetic microparticles within the assemblies. Direct contact of the droplet with air enables in situ manipulation and compartmentalized cascading chemical reactions with selective transport. Applications including functional microreactors, motors, and biomimetic robots are evident.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Surfactant-Aided Low-Salinity Waterflooding for Low-Temperature Carbonate Reservoirs

Carbonate reservoirs tend to be oil-wet/mixed-wet and heterogeneous because of mineralogy and diagenesis. The objective of this study is to improve oil recovery in low-temperature dolomite reservoirs using low-salinity and surfactant-aided spontaneous imbibition. The low-salinity brine composition was optimized using ζ-potential measurements, contact-angle (CA) experiments, and a novel wettability-alteration measure. Significant wettability alteration was observed on dolomite rocks at a salinity of 2,500 ppm. We evaluated 37 surfactants by performing CA, interfacial-tension (IFT), and spontaneous-imbibition experiments. Here, three (quaternary ammonium) cationic and one (sulfonate) anionic surfactants showed significant wettability alteration and produced 43–63% of original oil in place (OOIP) by spontaneous imbibition. At a low temperature (35°C), oil recovery by low-salinity effect is small compared with that by wettability-altering surfactants. Coreflood tests were performed with a selected low-salinity cationic surfactant solution. A novel coreflood was proposed that modeled heterogeneity and dynamic imbibition into low-permeability regions. The results of the “heterogeneous” coreflood were consistent with that of spontaneous-imbibition tests. These experiments demonstrated that a combination of low-salinity brine and surfactants can make originally oil-wet dolomite rocks more water-wet and improve oil recovery from regions bypassed by waterflood at a low temperature of 35°C.

02 PETROLEUM↗
DOE OSTI2020

Functional, Hierarchical Colloidal Liquid Crystal Gels and Liquid Crystal Elastomers Nanocomposites. Final Report

Biological systems rely on a hierarchy of dynamic, complex and reconfigurable compartments to carry out functions essential for life. This hierarchical organization serves as an amplifier that allows highly localized, molecular events to propagate into the mesoscale, resulting in dynamic functional properties of biological systems that have not yet been fully realized in synthetic material designs. We pursued a program of research in which we recreated such principles using synthetic liquid crystals (LC) as a versatile platform. We elucidated new hierarchical design strategies that heavily leverage surface anchoring, coexisting phases and interfacial tension gradient to realize equilibrium and non-equilibrium, dynamic mesoscale phenomena in the context of micrometer-sized LC droplets containing multiple compartments. Specifically, we unmasked how equilibrium and dynamical phenomena emerged from hierarchical organizations in reconfigurable, thermotropic liquid crystalline assemblies. The long-term impact of the project is to advance new hierarchical designs of complex soft matter systems in which biomimetic principles, including the propagation of events or information over multiple temporal and spatial scales, are enacted in a facile manner.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Self-Assembly and Phase Separation for Transport: A brief argument for the continued exploration of liquid crystal flows and electrodeposition in micro-gravity

Phase separation, interfacial tension gradients, and molecular self-assembly are all phenomena frequently observed when manipulating soft condensed matter systems on Earth. Depending on the system these processes can also be quite predictable. For instance, on Earth water droplets placed on hydrophobic surfaces will have contact angles > 90° with limited spread, contrary to their wetting behavior on hydrophilic surfaces. However, in an environment that is in a constant state of free-fall, where the gravitational field is reduced by 10%, such as on the International Space Station (ISS), buoyancy and its effect on fluid convection also become negligible. Fluid flow and phase behavior become less predictable. Thus, continuing the prior example, even if water droplets still remain in contact with a surface in microgravity (µg), the interface between the air and droplets will still remain significantly curved, appearing almost as if they were placed over completely nonwetting surfaces (Fig. 1a). Moreover, the negligible opposing buoyant force would also mean that if immiscible liquid droplets of a less dense character, or air bubbles even (Fig. 1b), were to be suspended within a larger water drop, these immiscible droplets or air bubbles would not migrate toward any one direction unless either artificially propelled by an external force or internal reaction inducing flow.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Engineered Water for Improved Oil Recovery from Fractured Reservoirs (Final Scientific/Technical Report)

The goal of this proposal is to field test the novel technology of engineered water (modifying ionic composition and/or adding surfactants or nanoparticles) injection to improve oil recovery from the carbonate matrix in fractured reservoirs. Carbonate reservoirs tend to be oil-wet/mixed-wet due to positively charged carbonate mineral surfaces and negatively charged acidic/asphaltic components in the oil. Many carbonate reservoirs are also highly fractured. Water injection does not work efficiently in fractured oil-wet reservoirs because water does not imbibe into the matrix. The water composition can be engineered with ionic modification, surfactants and nanoparticles which can change the wettability of carbonate rocks towards more water-wet conditions which can imbibe water into the matrix and push the oil into the fractures. The engineered water can also lower interfacial tension and minimize capillary forces so that gravity can push the oil up and out of the matrix. Wettability alteration also increases water relative permeability which can also improve oil recovery in non-fractured carbonate reservoirs. This technology, if successful, can be a game changer for West Texas carbonates.

02 PETROLEUM↗
DOE OSTI2022

Findings on Subtask 3.1 - Bakken Rich Gas Enhanced Oil Recovery Project

Total in-place oil for the Bakken petroleum system (BPS) (which includes the Bakken and Three Forks Formations) has been estimated to be 600 billion barrels (bbl). However, BPS wells have decline rates as high as 85% over the first 3 years of their lives, and primary recovery factors typically range from 3% to 10% of original oil in place. Given the low initial recovery rates, even small incremental productivity improvements could dramatically increase technically recoverable oil in the BPS. One potential solution is enhanced oil recovery (EOR) using gas injection, such as carbon dioxide (CO2) or hydrocarbon (HC) gases. While commonly used in conventional reservoirs, CO2 EOR in unconventional tight oil reservoirs has been limited to pilot tests. EOR using rich gas (mixture of methane, ethane, and propane) has also been employed in numerous pilots in several unconventional plays and has recently been successfully applied in the Eagle Ford play. If successful, large-scale gas-based EOR in the BPS could dramatically increase oil productivity and recovery factors and extend the life of the play for decades. While CO2 may be a technically suitable working fluid for EOR in the BPS, supplies are limited and costs for using CO2 in EOR pilots are prohibitively high. Meanwhile, produced gas flaring has presented challenges for BPS operators in North Dakota. Analysis conducted by the North Dakota Pipeline Authority indicates that the current gas-gathering infrastructure in North Dakota is insufficient to accommodate all of the associated gas that is produced from the BPS. The geographically isolated location of North Dakota relative to large natural gas markets, combined with suppressed natural gas prices, has made it economically challenging for industry to invest capital in expanding gas-gathering infrastructure in the state. These circumstances led to a research program conducted by the Energy & Environmental Research Center (EERC) in partnership with Liberty Resources Management Company LLC (LR) to examine the potential to use rich gas injection for EOR and mitigate flaring. A rich gas EOR pilot test was designed and executed by LR at its Stomping Horse development area in Williams County, North Dakota. From July 2018 through May 2019, a total of 160 million standard cubic feet (MMscf) of rich produced gas was injected into the BPS using five different wells in a sequential injection strategy. LR’s Leon–Gohrick drill spacing unit (DSU) was used as the test site. Regulatory oversight was provided by the North Dakota Industrial Commission (NDIC). Technical support was provided by the EERC through a series of laboratory, modeling, and field-based activities, and additional post-pilot research activities incorporated learnings from the test, developed new laboratory data, improved fracture modeling methods, and developed machine learning and big data analytics. The results from the Stomping Horse rich gas EOR pilot activities indicate that developing an effective, economical EOR approach for the BPS will require more field tests. Another key lesson learned from the Stomping Horse tests is that detailed pre- and posttest data on reservoir conditions and fluids production are essential. Robust reservoir characterization provides information that is crucial to creating realistic geomodels and conducting valid dynamic simulations of potential EOR scenarios. A detailed understanding of the completions and production history of offset wells is also necessary for valid test result interpretations. This knowledge is essential to designing the operational parameters of injectivity tests and interpreting the results. A conformance control strategy is also essential to success. Laboratory-based examinations of rich gas interactions with reservoir fluids and rocks were conducted, with an emphasis on determining the ability to mobilize oil in the tight reservoir rocks and shales of the BPS. Injection fluid composition was shown to have a positive impact on reducing reservoir oil minimum miscibility pressure (MMP), reducing interfacial tension (IFT), and altering wettability. IFT and contact angle measurements demonstrated that wettability can be altered in the presence of rich gas, suggesting the potential to improve oil recovery. Iterative modeling of surface infrastructure and reservoir performance using data generated by the various project activities was conducted. A geologic model of the Stomping Horse area was built; history-matched oil, gas, and water production was used in simulations of various EOR scenarios. Early programmatic modeling results were used to support LR’s design and operation of the EOR pilot and to provide insight regarding optimization of future commercial-scale BPS EOR design and operations. Post-pilot modeling focused on alternative methods of understanding complex fracture networks and accelerating simulation time. These led to improved simulation run times and provide excellent history-matching results. Several of these iterative models were used as the bases for developing algorithms into machine learning and big data analytics. History matching in reservoir simulation is time-consuming and computer processing-intensive. Machine learning algorithms were created, and an automated history-matching tool was developed. A large set of synthetic reservoir simulations were created to generate well responses (oil, gas, and water production, well bottomhole pressure [BHP], and tracer or propane breakthrough) for a set of EOR operating parameters that included offset well status (open or closed), injectate (rich gas or propane), injection rate, and injection well BHP. A user interface was developed to provide real-time visualization. Machine learning-based models were developed to provide rapid forecasting of well performance given a set of user-defined EOR operating parameters. These predictive models allow the user to modify the offset well status, injection rate, and injection well BHP and rapidly forecast future production performance. The combination of real-time visualization tools with real-time forecasting tools provides a framework for real-time control—operational changes that the EOR site operator can enact (e.g., changing gas injection rates) to affect the observed performance and potentially improve the EOR outcome. There is great reason to be optimistic about the future of EOR in the Bakken. The results of the laboratory studies suggest significant potential for high rates of oil mobilization using produced field gas injection under the right conditions. The results of the lab studies, combined with rigorous statistical analysis of well production data and associated modeling efforts, confirm the notion that fluid mobility within the reservoir is controlled by fractures. As more knowledge is gained about the nature and distribution of fracture networks in the Bakken, the industry will be in a better position to predict and, ultimately, influence fluid mobility. New field tests are necessary to develop a more complete understanding of those conditions. Thoughtful and creatively engineered field tests within a well-characterized geologic setting will yield the fundamental knowledge needed to take Bakken oil production to the next level. This subtask was cofunded through the EERC–U.S. Department of Energy Joint Program on Research and Development for Fossil Energy-Related Resources Cooperative Agreement No. DE-FE0024233. Nonfederal funding was provided by the North Dakota Industrial Commission’s Oil and Gas Research Program and Computer Modelling Group.

04 OIL SHALES AND TAR SANDS↗
DOE OSTI2023

INVESTIGATION OF ROCK-FLUID INTERACTIONS USING GEOMATERIAL MICROFLUIDICS

Illite and Illite-Smectite clays are reportedly the Caney Shale's most prevalent clay minerals. The swelling and fines migration of clays may occur when water-based fluids contact the clay minerals. This may result in the reduction of pore space and permeability, and wettability alteration. Therefore, we quantified the swelling potentials, fines migration and wettability alteration of Illite and Illite-Smectite clays upon exposure to model brines and a produced water, and a model oil and a crude oil. We measured density, viscosity, pH, TDS, and interfacial tension as they are important in multiphase flow and displacement characteristics. Geomaterial microfluidics is recently being used to study physicochemical interactions of solid-fluid systems. It facilitates visualizing the surface behavior upon exposure to various fluids. This study includes preparation and characterization of Illite-Smectite clay-coated glass capillary tubes. Illite and Illite-Smectite clay-coated geomaterial microfluidic surfaces were prepared to investigate the effects of first contact fluid, brine salinity, and aging on wettability. In this work, advancing and receding contact angles of model brine-air, model oil-air, produced water-air, crude oil-air, model brine-model oil systems, and produced water-crude oil systems have been measured in the untreated, and clay-coated microfluidic channels of 1000 µm width and 50 µm depth. The aging effect was studied by retaining the non-aqueous and aqueous solutions in the corresponding microfluidic channels for approximately 24 h in the case of channels first contacted by aqueous and non-aqueous solutions, respectively. The advancing and receding contact angles of Caney shale-crude oil-produced water systems were also measured. The experimental findings indicate the swelling potential, fines migration, and wettability alteration of Illite and Illite-Smectite clays. The results signify the influence of first contact fluid, brine salinity, and aging on wettability of the untreated and clay-coated microfluidic surfaces. The experiments also demonstrate the wetting nature of the Caney shale samples from reservoir and non-reservoir zones.

02 PETROLEUM↗
DOE OSTI2026

Interface and Thermophysical Properties of R 32 Refrigerant

Driven by the urgent demand for efficient cooling in microelectronics and advanced thermal management systems, difluoromethane (R32/CH 2 F 2 ) has emerged as a promising candidate owing to its favorable thermophysical properties, including high heat transfer efficiency and low viscosity. While bulk properties such as density, viscosity, and thermal conductivity have been widely studied, interfacial properties, including surface tension and interfacial thickness, remain comparatively underexplored, despite their importance in phase-transition dynamics. Here, we perform molecular dynamics (MD) simulations from 180 to 300 K using an optimized transferable force field for fluoropropenes with enhanced electrostatics to assess both bulk and interfacial behavior of R32. Simulations reproduced density within ±2.1%, viscosity within 3.05%, and thermal conductivity within 7.41% of NIST reference data. Heat capacities (C p and C v ) were predicted within 5%. For interfacial properties, surface tension trends were reproduced within 13.58% deviation, and the vapor–liquid coexistence curve closely matched reference data, yielding a critical temperature of 345.7 K (1.6% deviation) and a critical density of 0.397 g/cm 3 (6.4% deviation). Importantly, the vapor–liquid interface exhibited pronounced temperature-dependent broadening across the 180–290 K range. This behavior correlates with increasing molecular kinetic energy, reduction in intermolecular cohesive interactions, and a progressive loss of preferential dipole alignment, which collectively enhance thermal fluctuation amplitudes at elevated temperatures. These validated results provide predictive molecular-level insights, particularly for interfacial properties that remain less characterized. By reducing property prediction errors in key parameters such as critical temperature, this work provides reliable inputs for heat-exchanger and system models. Such correlations can support optimized component sizing, improved performance, and reduced refrigerant charge. Beyond R32, the methodology offers a transferable framework for blended and next-generation low-GWP refrigerants, contributing to sustainable thermal management aligned with the 2027 EU F-Gas regulation and 2030 Kigali Amendment.

Fluids↗
DOE OSTI2025

A fluctuating hydrodynamics model for nanoscale surfactant-laden interfaces

A multispecies diffuse interface model is formulated in a fluctuating hydrodynamics framework for the purpose of simulating surfactant interfaces at the nanoscale. The model generalizes previous work to ternary mixtures, employing a Cahn-Hilliard free energy density combined with incompressible, isothermal fluctuating hydrodynamics where dissipative fluxes include both deterministic and stochastic terms. The intermolecular parameters in the free energy are chosen such that one species acts as a partially miscible surfactant. From Laplace pressure measurements, we show that in this model the surface tension decreases linearly with surfactant concentration, leading to Marangoni convection for interfaces with concentration gradients. In the capillary wave spectrum for interfaces with and without surfactant, we find that for the former, the spectrum deviates significantly from classical capillary wave theory, presumably due to Gibbs elasticity. In non-equilibrium simulations of the Rayleigh-Plateau instability, deterministic simulations showed that the surfactant delays pinching of a fluid cylinder into droplets. However, stochastic simulations indicate that thermal fluctuations disrupt the surfactant's stabilizing effect. Similarly, the spreading of a patch of surfactant, driven by Marangoni convection, was found to be partially suppressed by thermal fluctuations.

Capillary waves↗
DOE OSTI2020

Self-Assembly of Silica Nanoparticles at Water–Hydrocarbon Interfaces: Insights from In Operando Small-Angle X-ray Scattering Measurements and Molecular Dynamics Simulations

To achieve tunable controls on the interactions of siliceous materials in subsurface environments bearing water and hydrocarbons, it is essential to determine the influence of hydrocarbon–water interfaces on the self-assembly of the silica particles. The hydrophilic silica particle have a tendency to aggregate on the water front of the interface. Self-assembly of silica nanoparticles proceeds via the migration of these nanoparticles to the water–hydrocarbon interface followed by aggregation at the interface. Fractal-like morphologies of assembled silica nanoparticles at water–hydrocarbon interfaces are observed. Rapid assembly of the hydrophilic silica nanoparticles at water–hydrocarbon interfaces corresponds to an overall reduction in the surface tension of water–toluene and water–heptane systems. These studies demonstrate the silica aggregation that is the precursor of silica polymerization, or nucleation and growth is influenced by the presence of hydrocarbons in subsurface geologic environments. These insights were derived from in operando ultrasmall and small-angle X-ray scattering (USAXS/SAXS) measurements, cryo-scanning electron microscopy (Cryo-SEM) imaging, and classical molecular dynamics simulations. As a result, these studies are intended to inform current and future efforts aimed at tuning silica reactivity in subsurface geologic environments to enhance permeability, the design and use of silica-based proppants to enhance fractures, and the development of effective strategies to control silica-based scaling behavior in subsurface reservoirs.

42 ENGINEERING↗
DOE OSTI2021

Nanoparticle-Induced Disorder at Complex Liquid–Liquid Interfaces: Effects of Curvature and Compositional Synergy on Functional Surfaces

The self-assembly of surfactant monolayers at interfaces plays a sweeping role in tasks ranging from household cleaning to the regulation of the respiratory system. The synergy between different nanoscale species at an interface can yield assemblies with exceptional properties, which enhance or modulate their function. However, understanding the mechanisms underlying coassembly, as well as the effects of intermolecular interactions at an interface, remains an emerging and challenging field of study. Herein, we study the interactions of gold nanoparticles striped with hydrophobic and hydrophilic ligands with phospholipids at a liquid–liquid interface and the resulting surface-bound complexes. We show that these nanoparticles, which are themselves minimally surface active, have a direct concentration-dependent effect on the rapid reduction of tension for assembling phospholipids at the interface, implying molecular coassembly. Through the use of sum frequency generation vibrational spectroscopy, we reveal that nanoparticles impart structural disorder to the lipid molecular layers, which is related to the increased volumes that amphiphiles can sample at the curved surface of a particle. The results strongly suggest that hydrophobic and electrostatic attractions imparted by nanoparticle functionalization drive lipid–nanoparticle complex assembly at the interface, which synergistically aids lipid adsorption even when lipids and nanoparticles approach the interface from opposite phases. The use of tensiometric and spectroscopic analyses reveals a physical picture of the system at the nanoscale, allowing for a quantitative analysis of the intermolecular behavior that can be extended to other systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗