Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Ignition delay time”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

An Experimental Kinetics Study of Isopropanol Pyrolysis and Oxidation behind Reflected Shock Waves

Isopropanol has potential as a future bio-derived fuel and is a promising substitute for ethanol in gasoline blends. Even so, little has been done in terms of high-temperature chemical kinetic speciation studies of this molecule. To this end, experiments were conducted in a shock tube using simultaneous CO and H2O laser absorption measurements. Water and CO formation during isopropanol pyrolysis was also examined at temperatures between 1127 and 2162 K at an average pressure of 1.42 atm. Species profiles were collected at temperatures between 1332 and 1728 K and at an average pressure of 1.26 atm for equivalence ratios of 0.5, 1.0, and 2.0 in highly diluted mixtures of 20% helium and 79.5% argon. Species profiles were also compared to four modern C3 alcohol mechanisms, including the impact of recent rate constant measurements. The Li et al. (2019) and Saggese et al. (2021) models both best predict CO and water production under pyrolysis conditions, while the AramcoMech 3.0 and Capriolo and Konnov models better predict the oxidation experimental profiles. Additionally, previous studies have collected ignition delay time (τign) data for isopropanol but are limited to low pressures in highly dilute mixtures. Therefore, real fuel–air experiments were conducted in a heated shock tube with isopropanol for stoichiometric and lean conditions at 10 and 25 atm between 942 and 1428 K. Comparisons to previous experimental results highlight the need for real fuel–air experiments and proper interpretation of shock-tube data. The AramcoMech 3.0 model over predicts τign values, while the Li et al. model severely under predicts τign. The models by Capriolo and Konnov and Saggese et al. show good agreement with experimental τign values. A sensitivity analysis using these two models highlights the underlying chemistry for isopropanol combustion at 25 atm. Additionally, modifying the Li et al. model with a recently measured reaction rate shows improvement in the model’s ability to predict CO and water profiles during dilute oxidation. Finally, a regression analysis was performed to quantify τign results from this study.

09 BIOMASS FUELS↗
DOE OSTI2022

Automatically generated model for light alkene combustion

Light alkenes are common combustion intermediates for a variety of fuels. Therefore, understanding their oxidation and pyrolysis chemistry is key to building detailed mechanisms for heavier fuels. This work was focused on the development and evaluation of a detailed kinetic mechanism suitable for the combustion of light alkenes up to C 4 without the use of tuned parameters, instead, the parameter values come from first principles or direct measurements. The generated mechanism accurately estimates the laminar burning velocity (S u ) and ignition delay time (IDT) of light alkenes available in the literature, which represent fundamental combustion properties at a wide range of conditions. Because each parameter is thought to have a physically realistic value, not tuned to these measurements, the new model could be used as a sub-mechanism in models for other applications. The reaction network was generated with the open-source Reaction Mechanism Generator (RMG) software. Sensitivity analyses were performed under wide ranges of temperatures and pressures, allowing for the identification of the most impactful species and reactions. Based on these, a comprehensive thermochemistry database, including calculations on 550 molecules performed in this work at the CBS-QB3 level of theory, and a kinetic library, including theoretically-derived reaction rates retrieved from the literature, were built and used in the mechanism generation. The developed mechanism was compared against several existing detailed kinetic mechanisms for ethene, propene, 1-butene, 2-butene, and isobutene. Here, the newly generated model is the most accurate among the ones analyzed, in terms of fractional bias and normalized mean square error. Hence, this new model was used to analyze the chemistry of alkene combustion. Key rate coefficients were compared, to identify the cause of deviations between the models and possible areas for further improvements.

09 BIOMASS FUELS↗
DOE OSTI2022

The influence of thermochemistry on the reactivity of propane, the pentane isomers and $n$-heptane in the low temperature regime

In this study, the influence of thermochemistry on the reactivity of fuels at low temperatures (600–1000 K) is studied here. Specifically, the effect of different sets of thermochemistry on chemical model predictions is explored, where various sets are calculated at different levels of theory in addition to recently updated group additivity values. Experimentally measured ignition delay times for propane, the pentane isomers and n-heptane are simulated using NUIGMech1.2 and replacing the thermochemistry of the low-temperature species with the calculated values. For propane, three different thermochemistry sets were calculated, namely CCSD(T)-F12/TZ-F12//B2PLYP-D3/TZ//B2PLYP-D3/TZ (QM1), CCSD(T)-F12/TZ-F12//B2PLYP-D3/TZ//ωB97X-D/TZ (QM2) and B2PLYP-D3/TZ/ωB97X-D/6-31G*//ωB97X-D/6-31G* (QM3). The QM2 results provide parameters to optimize new group additivity (NGA) values which are used to calculate the fourth set of thermochemistry. The model predictions using these four sets are compared to those using NUIGMech1.2 for propane. As the QM1 and QM2 calculations are expensive, the thermochemistry calculated from the QM3 and NGA calculations are used in the pentane isomer and n-heptane models. For all of the models, it is found that the thermochemistry of the species involved in the low-temperature reaction sequence ($RH$, $\dot{R}$, $RO_2H$, $R\dot{O}_2$, $\dot{Q}OOH$ and $\dot{O}_2QOOH$ species) significantly affect fuel reactivity. The NGA values were developed based on all of these species except $\dot{O}_2QOOH$ radicals. The thermochemistry of $\dot{O}_2QOOH$ species cannot be accurately calculated with the NGA representations due to the importance of non-next-nearest neighbor interactions of –OOH substitution. Further development of the NGA method to capture such interactions is in progress. Overall, the model developed using the NGA thermochemistry shows better agreement with experimental data than the model using thermochemistry from affordable and prominent QM methods, such as QM3. Based on the results presented for propane, the pentane isomers and n-heptane, the thermochemistry calculated using the NGA method can be used to model the oxidation of higher order hydrocarbons at low temperatures.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2026

An experimental and kinetic modeling study of the ignition of 2-methyl decane

Ignition delay times (IDTs) of 2-methyl decane (C 11 H 24 -2) are measured in a high-pressure shock tube and in a rapid compression machine at equivalence ratios in the range 0.5–2.0 at 90 % dilution, at temperatures in the range 600–1430 K and at pressures of 15 and 30 bar. To clarify the effect of the branched methyl group on fuel oxidation, IDTs of n-undecane (nC 11 H 24 ) are also measured at similar conditions to those measured for C 11 H 24 -2. A new chemical kinetic mechanism, using C3MechV4.0.1 as the core chemistry, is developed and validated against the new experimental data. The thermodynamic properties of the fuel (RH), alkyl (Ṙ), alkyl peroxy (RȮ 2 ), hydroperoxy-alkyl (Q̇OOH), and peroxy hydroperoxy alkyl (Ȯ 2 QOOH) radicals are updated in both the C 11 H 24 -2 and nC 11 H24 models using THERM25. A reaction path flux analysis for C 11 H 24 -2 at different temperatures was conducted. Compared to nC 11 H 24 , C 11 H 24 -2 shows slower reactivity. At low and intermediate temperatures, the chain propagation pathway Q̇OOH ↔ C 11 cyclic ether + ȮH is favored for C 11 H 24 -2, while the chain branching pathway Q̇OOH ↔ Ȯ 2 QOOH ↔ C 11 carbonyl hydroperoxide (KHP) + ȮH is suppressed, leading to lower reactivity compared to nC 11 H 24 . At high temperatures, the presence of the branched methyl group inhibits the direct decomposition of the fuel, resulting in reduced C 2 H 4 formation, which in turn suppresses the reactivity of the fuel.

2-methyl decane↗
DOE OSTI2023

Validation of Octane Hyperboosting Phenomenon in Prenol and Structurally Related Olefinic Alcohols

Hyperboosting is a recently discovered phenomenon in which the research octane number (RON) of a blend is higher than both the neat blendstock and the neat fuel it was blended into. RON is a measure of a fuel's resistance to knock, and knock is a cause of engine inefficiency. Blends which exhibit hyperboosting are blends in which an overall improvement in engine efficiency may be expected. The first discovery of hyperboosting came from blending experiments in which prenol was blended into several different base fuels. Here, ignition delay time (IDT) measurements taken using a commercially available constant volume combustion chamber called the Advanced Fuel Ignition Delay Analyzer (AFIDA) are presented. The data show that some prenol blends have longer IDTs (lower reactivity) than either neat prenol or the base fuel, providing further evidence of hyperboosting. Additionally, more blending data is presented in which the base fuel is varied, which allows for a better understanding of hyperboosting sensitivity to chemical classes. The data indicate that aromatics may inhibit, and branched alkanes may enhance the magnitude of hyperboosting observed. Enthalpy of vaporization estimates are also given for several molecules which are blended into a 4-component surrogate. These estimates are derived from Equation of State simulations and reveal that there is no observable correlation between hyperboosting and enthalpy of vaporization. Blending data for molecules which share structural similarities with prenol are also presented. Structure property relationships are suggested, in which the double bond motif of prenol seems to play an important role in hyperboosting. This may help to understand hyperboosting and its underlying mechanism. Lastly, blending curves of surrogate blends with prenol experienced hyperboosting under lean (Homogeneous Charged Compression Ignition-HCCI) operating conditions, which validates that hyperboosting is not an artifact of the octane test methods, but inherent to the properties of prenol.

ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2024

Combustion characteristics of diisopropoxymethane, a low-reactivity oxymethylene ether

Oxymethylene ethers (OMEs) have been studied for use as low-sooting diesel fuel additives or substitutes; very little literature discusses OMEs as spark-ignition (SI) fuels due to their typically high cetane numbers. In this work, a lower-reactivity, branched OME, diisopropoxymethane (DIPM), is evaluated to determine its effectiveness as a spark-ignition fuel, as it is the lowest-reactivity OME (as determined by Indicated Cetane Number) thus far evaluated in the literature. DIPM is synthesized in-house via acetalization from isopropanol (iPrOH) and trioxane using standard OME production practices. DIPM was then tested in a rapid compression machine (RCM) for autoignition and spark ignition characteristics, and in a modified CFR engine to determine effective octane numbers. In the RCM, an autoignition temperature sweep was performed at stoichiometric conditions from 1000/T = 1.7 - 1.0, at 5:1 inert ratio (comparable to approximately 25% EGR), where it was found that DIPM has ignition delay times 5–10x faster than isooctane and displays NTC ignition behavior. Blends with iPrOH indicate that reactivity can be matched with isooctane with low blend ratios of iPrOH in DIPM. Flame speeds were tested with a laser spark for ignition in the RCM, where the flame speed of DIPM and isooctane is determined to be comparable at engine relevant conditions. In the CFR engine, effective RON and MON based on pressure trace frequency domain measurements were determined for DIPM and a 15 vol% iPrOH in DIPM blend. Neat DIPM has (R+M)/2 = 59 and a negative sensitivity of S = -18, consistent with its NTC behavior and higher reactivity. Furthermore the DIPM/iPrOH blend has positive sensitivity and a pump-gasoline range (R+M)/2 = 89.3. DIPM on its own is unlikely to be an effective SI fuel, however, when blended with iPrOH as an ON booster, it may be a promising SI candidate fuel.

09 BIOMASS FUELS↗
NASA NTRS2011

Convective Heat Transfer Scaling of Ignition Delay and Burning Rate with Heat Flux and Stretch Rate in the Equivalent Low Stretch Apparatus

To better evaluate the buoyant contributions to the convective cooling (or heating) inherent in normal-gravity material flammability test methods, we derive a convective heat transfer correlation that can be used to account for the forced convective stretch effects on the net radiant heat flux for both ignition delay time and burning rate. The Equivalent Low Stretch Apparatus (ELSA) uses an inverted cone heater to minimize buoyant effects while at the same time providing a forced stagnation flow on the sample, which ignites and burns as a ceiling fire. Ignition delay and burning rate data is correlated with incident heat flux and convective heat transfer and compared to results from other test methods and fuel geometries using similarity to determine the equivalent stretch rates and thus convective cooling (or heating) rates for those geometries. With this correlation methodology, buoyant effects inherent in normal gravity material flammability test methods can be estimated, to better apply the test results to low stretch environments relevant to spacecraft material selection.

Olson, Sandra↗
DOE OSTI2025

Numerical Investigation of Ammonia/n-Heptane Dual-Fuel Spray Flames Using Large Eddy Simulations

Diesel engines are extensively used in heavy-duty transportation, power generation, and marine vehicles due to their superior thermal efficiency and extended high-load operability compared to spark ignition (SI) engines. However, combustion in diesel engines is generally characterized by locally rich fuel–air mixtures and high combustion temperatures, causing significant amounts of soot and NO x emissions from these engines. Utilizing carbon-free alternative fuels and enhancing fuel efficiency represent promising strategies to mitigate greenhouse gas (GHG) and other emissions in the heavy-duty transportation sector. In this context, ammonia (NH 3 ), as a hydrogen carrier, has received significant attention as a viable substitute for hydrocarbon fuels due to its carbon-free composition, relatively high energy density, and well-established infrastructure. Many previous studies have considered combustion and emission characteristics of ammonia-hydrocarbon fuel blends in engines and simplified flames. But, detailed investigations on the effects of ammonia on the performance of hydrocarbon fuels under engine conditions are lacking. In the present study, we perform large eddy simulations (LES) of the ignition and flame processes in a constant-volume combustion reactor, where n-heptane is injected in an ammonia/air ambient mixture in a diesel-like environment. A detailed and validated reaction mechanism containing 302 species and 1981 reactions is employed. The Engine Combustion Network Spray H experimental data is used to validate the spray model under both non-reacting and reacting conditions. Dual-fuel combustion is simulated using the well-stirred reactor (WSR) approach. Results are presented for two spray cases: (1) single fuel (SF) with n-heptane injected into a mixture of air and combustion products and (2) dual-fuel (DF) with the injection of n-heptane in a mixture of air, ammonia, and combustion products. It is observed that the presence of ammonia has a significant effect on the ignition and flame development processes. With ammonia addition, both the first- and second-stage ignition delay times increase, but the effect of ammonia on the second-stage ignition is significantly more prominent. In addition, the ignition kernel size and growth rate decrease noticeably. For SF spray, the main ignition is characterized by multiple ignition kernels near the spray tip, whereas for DF spray, a single relatively small ignition kernel forms and grows slowly in the downstream direction. The flame development and the final quasi-steady flame structure are also modified due to ammonia. Here, the outcome of this research would enable a better understanding of ammonia–diesel dual-fuel spray flame behavior and guide the development of associated engine combustion strategies.

ammonia↗
DOE OSTI2023

Genetic algorithm optimization of a chemical kinetic mechanism for propane at engine relevant conditions

Propane has demonstrated significant potential for reductions in greenhouse gas and pollutant emissions in medium- and heavy-duty engine applications, but further improvements require accurate, compact, and scalable chemical kinetic mechanisms to design the next generation of propane fueled engines, particularly at the boosted operating conditions necessary to meet the power density demand of medium- and heavy-duty applications. In this work, six key chemical reactions were identified in a reduced mechanism with 70 species and 352 reactions through a sensitivity analysis performed at conditions typical of thermodynamic trajectories observed in a high compression ratio, long stroke engine operated on propane from throttled to boosted operating conditions. While the original mechanism was validated against rapid compression machine (RCM) data, it was found to overpredict experimental autoignition tendencies in 2-zone, 0-D SI engine simulations performed in Chemkin Pro. Subsequently, a genetic algorithm approach was used to optimize the six reaction rate parameters within established uncertainty bounds by performing RCM simulations and comparing to two independent sets of literature ignition delay times for propane, thus generating two new kinetic mechanisms. The first optimization achieved a mean absolute percent error (MPE) reduction in 2nd stage ignition delay of 61.4% in seven generations, while the second optimization utilized a newer experimental RCM dataset, and achieved MPE reduction of 56.7% in seven generations, and further marginal improvement to 57.8% reduction in 34 generations. Finally, the two mechanisms were then evaluated again in the 2-zone 0-D SI engine model in Chemkin Pro comparing typical mean and knocking cycle trajectories, and it was found that the second optimized mechanism provided better prediction of knock onset at the representative conditions evaluated in this work, particularly for higher load operating conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2026

Optimization of a 10–Step Reduced CH₄/O₂ Combustion Mechanism for RDRE Applications

A 10-step, 9-species reduced mechanism for methane/oxygen combustion is evaluated and optimized for use in rotating detonation rocket engine (RDRE) simulations at an operating pressure of 10 bar. The mechanism is assessed against GRI-Mech 3.0 for ignition delay times, adiabatic equilibrium temperature and species, Chapman-Jouguet (CJ) detonation parameters, and laminar flame speed. A sequential Nelder–Mead optimization procedure is applied to the rate constants of reactions R1, R4, and R5, targeting ignition delay agreement over the equivalence ratio range φ = 1.0–1.4 and temperature range T = 1400–2000 K. The optimized mechanism achieves ignition delay agreement within 28% of GRI-Mech 3.0 for the temperature range relevant to RDRE operation (τ ≥ 5 μs). Adiabatic equilibrium temperatures and CJ detonation parameters are reproduced within 0.15% of GRI-Mech 3.0 values, confirming thermodynamic consistency of the mechanism. Laminar flame speed predictions deviate significantly from GRI-Mech 3.0, which is attributed to the absence of HO₂ chemistry in the reduced mechanism; this limitation does not affect RDRE simulation fidelity since laminar flame propagation is of secondary importance in RDREs.

Computational Fluid Dynamics↗
DOE OSTI2022

A comprehensive experimental and kinetic modeling study of di-isobutylene isomers: Part 2

A wide variety of high temperature experimental data obtained in this study complement the data on the oxidation of the two di-isobutylene isomers presented in Part I and offers a basis for an extensive validation of the kinetic model developed in this study. Due to the increasing importance of unimolecular decomposition reactions in high-temperature combustion, we have investigated the di-isobutylene isomers in high dilution utilizing a pyrolysis microflow reactor and detected radical intermediates and stable products using vacuum ultraviolet (VUV) synchrotron radiation and photoelectron photoion coincidence (PEPICO) spectroscopy. Additional speciation data at oxidative conditions were also recorded utilizing a plug flow reactor at atmospheric pressure in the temperature range 725-1150 K at equivalence ratios of 1.0 and 3.0 and at residence times of 0.35 s and 0.22 s, respectively. Combustion products were analyzed using gas chromatography (GC) and mass spectrometry (MS). Ignition delay time measurements for di-isobutylene were performed at pressures of 15 and 30 bar at equivalence ratios of 0.5, 1.0, and 2.0 diluted in 'air' in the temperature range 900-1400 K using a high-pressure shock-tube facility. New measurements of the laminar burning velocities of di-isobutylene/air flames are also presented. The experiments were performed using the heat flux method at atmospheric pressure and initial temperatures of 298-358 K. Moreover, data consistency was assessed with the help of analysis of the temperature and pressure dependencies of laminar burning velocity measurements, which was interpreted using an empirical power-law expression. Electronic structure calculations were performed to compute the energy barriers to the formation of many of the product species formed. The predictions of the present mechanism were found to be in adequate agreement with the wide variety of experimental measurements performed.

09 BIOMASS FUELS↗
NASA NTRS1974

Ignition of partially shattered liquid fuel drops in a reflected shock wave environment

An experimental investigation of the ignition of individual fuel drops after their interaction with an incident and a reflected shock wave near the end wall of a shock tube has been carried out. The influence of the aerodynamic shattering of the fuel drop by the convective flow on the ignition characteristics has been examined by varying the drop-end wall separation distance. Data are presented which show the ignition delay times to be a function of the various experimental conditions encountered in this study. A comparison is made with previous investigations concerning the ignition of a liquid fuel drop due only to the interaction with an incident shock wave.

Wierzba, A. S.↗
DOE OSTI2024

DME-Propane Autoignition Measurements inside a Shock Tube

Dimethyl ether (DME) is a biofuel that has the potential to replace diesel in heavy-duty engines. A blend of propane (C3H8) and DME could reduce emissions when compared to diesel at heavy-duty compression engine-relevant conditions. Testing a potential new mixture in a compression engine requires a high-fidelity chemical kinetics model that accurately predicts autoignition delay times, which is especially necessary for a compression engine. In this work, autoignition data has been gathered at an equivalence ratio of 2.0 for pressures of 60 and 80 bar. DME and propane were combusted in synthetic air while excited hydroxyl (OH*) chemiluminescence was used to gather ignition delay times. Data was compared to recent chemical kinetic mechanisms for the two different pressures. Using the mechanism with the best fit of autoignition data, a sensitivity analysis was conducted to analyze the chemical kinetics of the DME/C3H8 combustion at elevated pressures.

Mohammed, Zuhayr Pasha↗
DOE OSTI2024

Asynchronicity in opposed-piston RCMs: Does it matter?

Rapid Compression Machines (RCMs) are widely utilized to study combustion phenomena at engine-relevant conditions, and significant efforts are typically made to create a quiescent environment, particularly for investigations of autoignition chemistry. Opposed-piston configurations can be advantageous due to shorter compression times and reduced surface area to volume ratios. Each side must be actuated simultaneously, but this can be challenging in practice. These devices, like most RCMs, utilize hydraulics for actuation, speed control and arrestation of the piston at the end of the stroke; there is no mechanical control or linkage of the two piston trajectories. To quantify the magnitudes and effects of piston asynchronous behavior, this work employs both detailed experimental measurements and, for the first time, high-fidelity, Direct Numerical Simulation (DNS). The boundary conditions are carefully considered applying insight from high-resolution linear variable differential transformer (LVDT) measurements of the piston trajectory and a zero-dimensional kinematics model of the piston-shaft assembly. Sufficient resolution in the piston crevice region is used. The complicated fluid dynamical behavior that can evolve during piston compression and the ensuing delay processes due to offset timings from t offset = 0-10 ms is elucidated. It is found that near t offset = 6 ms and beyond, the boundary layer on the face of the first-seating piston can be sufficiently perturbed, due initially to reemergence of gas from the crevice of the firstseating piston, so that the adiabatic core can become degraded at long ignition delay times. Substantial mixing of colder gas into the interior of the reaction chamber can alter the measurements, similar to effects previously observed for improper piston crevice configuration. In conclusion, experimental techniques to mitigate asynchronous behavior are discussed and demonstrated.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2022

Replicating HCCI-like autoignition behavior: What gasoline surrogate fidelity is needed?

This work seeks to characterize the fidelity needed in a gasoline surrogate with the intent to replicate the complex autoignition behavior exhibited within advanced combustion engines, and specifically Homogeneous Charge Compression Ignition (HCCI). A low-temperature gasoline combustion (LGTC) engine operating in HCCI mode and a rapid compression machine (RCM) are utilized to experimentally quantify fuel reactivity, through autoignition and preliminary heat release characteristics. Fuels considered include a research grade E10 U.S. gasoline (RD5-87), three multi-component surrogates (PACE-1, PACE-8, PACE-20), and a binary surrogate (PRF88.4). Each fuel was studied at lean/HCCI-like conditions covering a wide range of temperatures and pressures that are representative of naturally aspirated to high boost engine operation. Detailed chemical kinetic modeling is also undertaken using a recently updated gasoline surrogate kinetic model to simulate the RCM experiments and to provide chemical insight into surrogate-to-surrogate differences. The LGTC engine experiments demonstrate nearly identical reactivity between PACE-20 and RD5-87 across studied conditions, while faster phasing is seen for both PACE-1 and PACE-8 due to their stronger intermediate- and low-temperature heat release (ITHR/LTHR) at naturally aspirated and boosted conditions, respectively. The RCM experiments reveal typical low-temperature, negative temperature coefficient (NTC) and intermediate-temperature autoignition behaviors at all pressure conditions for RD5-87, which are qualitatively reproduced by all surrogates. Quantitative discrepancies in both autoignition and preliminary heat release are observed for all surrogates, while their ability to replicate RD5-87 autoignition behavior follows the order of PACE-20 > PACE-1 > PACE-8 > PRF88.4. Excellent mapping is obtained between the LGTC engine and the RCM, where the engine pressure-time trajectories can be characterized by the regimes represented by the RCM autoignition isopleths. The kinetic model performs commendably when simulating both autoignition and preliminary heat release of PACE-20, while typically overpredicting ignition delay times for PACE-1, PACE-8 and PRF88.4 at high-pressure and low-temperature/NTC conditions. Sensitivity and rate of production (ROP) analyses highlight surrogate-to-surrogate differences in the governing chemical kinetics where n-pentane initiates rapid OH branching at a faster rate and an earlier timing for PACE-20 than iso-pentane does for PACE-1 and PACE-8, making it computationally more reactive than the other surrogates. The current study highlights the need to include non-standardized properties, such as the lean/HCCI-like autoignition characteristics, in addition to ASTM properties (e.g., RON, MON) as metrics of fuel reactivity and targets to be matched when formulating high-fidelity surrogates that fully capture gasoline advanced combustion behavior such as HCCI-like autoignition.

42 ENGINEERING↗
NASA NTRS2014

Cool-flame Extinction During N-Alkane Droplet Combustion in Microgravity

Recent droplet combustion experiments onboard the International Space Station (ISS) have revealed that large n-alkane droplets can continue to burn quasi-steadily following radiative extinction in a low-temperature regime, characterized by negative-temperaturecoefficient (NTC) chemistry. In this study we report experimental observations of n-heptane, n-octane, and n-decane droplets of varying initial sizes burning in oxygen/nitrogen/carbon dioxide and oxygen/helium/nitrogen environments at 1.0, 0.7, and 0.5 atmospheric pressures. The oxygen concentration in these tests varied in the range of 14% to 25% by volume. Large n-alkane droplets exhibited quasi-steady low-temperature burning and extinction following radiative extinction of the visible flame while smaller droplets burned to completion or disruptively extinguished. A vapor-cloud formed in most cases slightly prior to or following the "cool flame" extinction. Results for droplet burning rates in both the hot-flame and cool-flame regimes as well as droplet extinction diameters at the end of each stage are presented. Time histories of radiant emission from the droplet captured using broadband radiometers are also presented. Remarkably the "cool flame" extinction diameters for all the three n-alkanes follow a trend reminiscent of the ignition delay times observed in previous studies. The similarities and differences among the n-alkanes during "cool flame" combustion are discussed using simplified theoretical models of the phenomenon

microgravity combustion↗
DOE OSTI2022

An experimental and modeling study on auto-ignition kinetics of ammonia/methanol mixtures at intermediate temperature and high pressure

A rapid compression machine (RCM) has been applied to measure the ignition delay times of NH 3 /CH 3 OH mixtures covering pressures of 20 and 40 bar, equivalence ratios of 0.5, 1.0 and 2.0, and temperatures between 845 and 1100 K. Here the measurements show that the NH 3 /CH 3 OH mixtures become more reactive with increasing methanol addition. Addition of merely 1% (molar basis) of CH 3 OH to NH 3 lowers the ignition temperature around 100 K at 40 bar in comparison to pure NH 3 . The ignition delay is a complex function of fuel mixture and stoichiometry. For the 1% CH 3 OH mixture, the leaner mixtures are more reactive, while the reverse trend is found for mixtures with 5%, 20% and pure CH 3 OH. Analysis of the pressure profiles shows three distinct ignition modes for NH 3/ CH 3 OH mixtures, facilitated by the pre-ignition heat release from NH 3 consumption. A detailed mechanism for ignition of NH 3 /CH 3 OH fuel blends has been developed, capable of reproducing the ignition behavior of mixtures with reasonable accuracy. A subset for amine / methanol interactions was established, with rate constants for the key reaction between NH 2 and CH 3 OH calculated from ab initio theory. A sensitivity analysis indicates that the critical reactions during the auto-ignition process vary with the CH 3 OH mole fraction in the fuel. The ammonia chemistry, namely NH 2 + NO, NH2 + NO 2 and NH 2 + HO 2 , is dominant for the mixture with 1% CH 3 OH, while the reactions related to CH 3 OH and H 2 O 2 are more important for the 20% CH 3 OH mixture. The interaction between ammonia and methanol shows a more prominent effect on auto-ignition for mixtures with 5% CH 3 OH in fuel as compared to those with 1% and 20% CH 3 OH. According to the modeling results, methanol addition is found to enrich the O/H radical pool, consuming ammonia and promoting auto-ignition through different reaction pathways.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Investigating the kinetic effect of prenol on iso -octane auto-ignition by means of an experimental and modeling study

A detailed experimental and kinetic modeling study was dedicated to understand the reported octane hyperboosting effect of prenol, by means of the measurement of the ignition delay times of its blends with iso -octane, and measurement of the mole fraction profiles of the fuels and intermediates inside the ULille rapid compression machine. Here, these results show that prenol addition leads to a reduction of the first-stage ignition phenomena and negative temperature coefficient behavior, which is only qualitatively captured by the model and is consistent with knock resistance improvement. It is suggested that this behavior is caused by two different factors. The first originates from gas-phase reactivity of prenol, and spans from the formation of unreactive unsaturated species through resonance-stabilized radicals, thereby constituting a competitive pathway for the radical pool generated by iso -octane. The second is of catalytic nature and cannot be captured by means of gas-phase kinetic modeling, but could also play an important role in the behavior of prenol in internal combustion engines.

42 ENGINEERING↗