Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “INLET”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Statistical prediction of dynamic distortion of inlet flow using minimum dynamic measurement. An application to the Melick statistical method and inlet flow dynamic distortion prediction without RMS measurements

The Melick method of inlet flow dynamic distortion prediction by statistical means is outlined. A hypothetic vortex model is used as the basis for the mathematical formulations. The main variables are identified by matching the theoretical total pressure rms ratio with the measured total pressure rms ratio. Data comparisons, using the HiMAT inlet test data set, indicate satisfactory prediction of the dynamic peak distortion for cases with boundary layer control device vortex generators. A method for the dynamic probe selection was developed. Validity of the probe selection criteria is demonstrated by comparing the reduced-probe predictions with the 40-probe predictions. It is indicated that the the number of dynamic probes can be reduced to as few as two and still retain good accuracy.

Schweikhard, W. G.↗
NASA NTRS1987

Experimental, water droplet impingement data on two-dimensional airfoils, axisymmetric inlet and Boeing 737-300 engine inlet

An experimental method has been developed to determine the droplet impingement characteristics on two- and three-dimensional bodies. The experimental results provide the essential droplet impingement data required to validate particle trajectory codes, used in aircraft icing analyses and engine inlet particle separator analyses. A body whose water droplet impingement characteristics are required is covered at strategic locations by thin strips of moisture absorbing (blotter) paper, and then exposed to an air stream containing a dyed-water spray cloud. Water droplet impingement data are extracted from the dyed blotter strips, by measuring the optical reflectance of the dye deposit on the strips, using an automated reflectometer. Impingement efficiency data obtained for a NACA 65(2)015 airfoil section, a supercritical airfoil section, and Being 737-300 and axisymmetric inlet models are presented in this paper.

Papadakis, M.↗
NASA NTRS1947

Investigation of 10-Stage Axial-Flow X24C-2 Compressor: Performance at Inlet Pressure of 21 Inches Mercury Absolute and Inlet Temperature of 538 R - 1

The performance at inlet pressure of 21 inches mercury absolute and inlet temperature of 538 R for the 10-stage axial-flow X24C-2 compressor from the X24C-2 turbojet engine was investigated. the peak adiabatic temperature-rise efficiency for a given speed generally occurred at values of pressure coefficient fairly close to 0.35.For this compressor, the efficiency data at various speeds could be correlated on two converging curves by the use of a polytropic loss factor derived.

Schum, Harold J.↗
NASA NTRS1957

Experimental investigation of an axial-flow-compressor inlet stage operating at transonic relative inlet Mach numbers V : rotor blade-element performance at a reduced blade angle

At a corrected speed of 1100 feet per second, the low-blade-angle rotor operated with a relative inlet Mach number of 1.2, a diffusion factor of 0.65, and an axial velocity ratio of 0.71 in the tip region (11 percent of passage height away from the outer wall). The measured minimum-loss coefficient was 0.35, and this value falls above a previous correlation of rotor losses with diffusion factor. Through a comparison with data for three other rotors, the occurrence of high losses was related to a high suction-surface Mach number. These comparisons also indicated that axial velocity ratios between 0.73 and 1.10 have no independent effect on losses.

Schwenk, Francis C↗
NASA NTRS1956

Performance of variable two-dimensional inlet designed for engine-inlet matching I : performance at design Mach number of 3.07

The inlet was investigated with both a two-oblique-shock and an isentropic compression ramp. Provisions for a variety of bypass systems were incorporated and none decreased pressure recovery by more than about 1 percent. By utilizing throat boundary-layer control, critical pressure recoveries of 64 and 70 percent were obtained with the two-shock and isentropic ramps, respectively. Diffuser-exit air distortion was about 5 percent at critical operation Theoretical cowl pressure drag was equal to about 10 percent of the net thrust of an assumed engine.

Beheim, M A↗