Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “HOT PRESSING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

High temperature compressive cracking in hot-pressed silicon nitride

Results are presented for high-temperature (1370, 1430, 1540, 1590 C) slow-strain-rate compression tests on cylindrical specimens of hot-pressed Si3N4 of the HS-130 brand under various compressive loads. The results are presented in terms of number of longitudinal cracks, percent increase in diameter, percent decrease in length, and percent loss in weight. Scanning electron micrographs are presented of cylindrical surfaces of compression specimens tested at 1430 C for 640 MN/sq m and at 1590 C for 220 MN/sq m. As compared to results obtained by other investigators, it appears more likely that the cracks resulting from compressive loading are due to subcritical crack growth caused by circumferential tensile stresses acting across grain boundaries that contain a viscous silicate glass phase.

Sanders, W. A.↗
NASA NTRS1991

Thermoelectric properties of hot-pressed fine particulate powder SiGe alloys

A novel material system and its fabrication technique have been defined and applied to the production of SiGe thermoelectric material through the hot pressing of 50-100 A ultrafine particulates into 80/20 SiGe. Relative to conventionally processed SiGe, a reduction of thermal conductivity of up to 40 percent is achieved in conjunction with an enhancement of material figure-of-merit of the order of 10-15 percent.

Beaty, John S.↗
NASA NTRS1991

Thermoelectric properties of hot pressed p-type SiGe alloys

This paper presents the results of measurements of electrical resistivity, Seebeck coefficient, thermal conductivity, as well as Hall carrier concentration, and mobility, for hot pressed SiGe 80 at. pct Si-20 at. pct Ge (SiGe) thermoelectric materials containing 0.24-3.0 at. pct boron. The carrier concentration was varied by annealing and quenching at different high temperatures. Figure-of-merit, Z, was found to be 0.60 +/- 0.03 x 10 exp -3/K over a carrier concentration range from 1.8- 3.5 x 10 exp -20/cu cm. This result is very encouraging from a production standpoint, since the dopant concentration is not critical.

Bajgar, Clara↗
NASA NTRS1983

Grain-boundary phases in hot-pressed silicon nitride containing Y2O3 and CeO2 additives

Auger electron spectroscopy in conjunction with X-ray powder diffraction and scanning electron microscopy is used to analyze the grain-boundary phases of Y2O3- and CeO2-doped Si3N4 hot-pressed materials in order to demonstrate that the additives concentrate predominantly in the grain boundaries of Si3N4 in the form of various oxynitride phases. A high oxygen content observed in sample fracture surfaces was found to be consistent with the existence of an oxygen-enriched phase in the grain boundaries. The presence of yttrium and cerium in the fracture surfaces and an overall increase in the O/N ratio imply that the additive oxides are predominantly concentrated in the intergranular phases.

Guha, J. P.↗
NASA NTRS1984

Hot-pressed silicon nitride with various lanthanide oxides as sintering additives

The effects of addition of various lanthanide oxides and their mixture with Y2O3 on the sintering of Si3N4 were investigated. The addition of simple and mixed lanthanide oxides promoted the densification of Si3N4 in hot-pressing at 1800 C under 300-400kg/ centimeters squared for 60 min. The crystallization of yttrium and lanthanide-silicon oxynitrides which was observed inn the sintered body containing yttrium-lanthanide mixed oxides as additives led to the formation of a highly refractory Si3N4 ceramic having a bending strength of 82 and 84 kg/millimeters squared at room temperature and 1300 C respectively. In a Y2O3+La2O3 system, a higher molar ratio of La2O3 to Y2O3 gave a higher hardness and strength at high temperatures. It was found that 90 min was an optimum sintering time for the highest strength.

Ueno, K.↗
DOE OSTI2018

Formation of gradient microstructure and mechanical properties of hot-pressed W-20 wt% Cu composites after sliding friction severe deformation

Highlights: • W particles of composites were refined during sliding friction treatment (SFD). • Dislocation, dislocation tangles and boundary clearly exist in deformed W particle. • YS and UTS of SFDed sample are 308.74 MPa and 553.60 MPa owing to the refinement. • Electrical conductivity of SFDed sample decreased from 33 IACS% to 28.5 IACS%. • Fracture mode changing from inter-granular mode to trans-granular. - Abstract: W-based alloys are currently considered promising candidates for high heat flux components in future fusion reactors. In this paper, hot pressed W-20 wt%Cu composites were treated at room temperature using a sliding friction severe deformation (SFD) process, with a moving speed of 0.2 m/s and an applied load of 500 N. Microstructural evolution of composites after the SFD treatment was evaluated and compared with that of the untreated composites. Results showed that there was a gradient structure generated and an obvious refinement in tungsten particles size in the surface layer after the SFD process. The average particle size of tungsten in the SFD treated composites was 2.60 μm, whereas it was 4.5 μm for tungsten in the untreated composites. Fracture surfaces of the composites indicated that the SFD treatment destroyed the W skeleton and changed fracture mode from predominant inter-granular one to trans-granular one due to the decrease in contact area of W-W inter-particles. Yield strength and ultimate tensile strength of composites after the SFD treatment were 308 MPa and 553 MPa, respectively. The treated composites exhibited micro-hardness values with an average reading of about 308 HV. Analysis of the facture microstructures clearly suggested that the tungsten particles in the treated composites are consisted of dislocations and boundaries as well as dislocation tangles. The electrical conductivity of the composites was decreased from 33 IACS% to 28.5 IACS% after the SFD treatment, mainly due to loss or squeezing of copper into the inner surface.

36 MATERIALS SCIENCE↗
NASA NTRS1977

Effects of pressure and temperature on hot pressing a sialon

The combined effects of temperature and pressure on the resulting density of a sialon (i.e., a ceramic composed of Si, Al, O, and N) are evaluated. Pressures in the 3.5-27.5 MPa range and temperatures in the 1550-1750 C range are considered. It is found that: (1) fully dense sialon bodies may be produced at lower temperatures than those usually used in the field, (2) the phase equilibrium reaction is increased by increased pressure, (3) the iso-density contour may be used to help design the desired microstructure, (4) phase changes occurring in the sample during hot pressing influenced sialon densification to a large extent, and (5) microstructures exceeding 98% theoretical density suggest that plastic deformation has contributed to densification.

Yeh, H. C.↗
NASA NTRS1993

Optimization of Hot-Pressed n-Type SiGe/GaP and p-Type SiGe/B Thermoelectric Materials

A comprehensive experimental and theoretical work has been conducted in order to optimize the thermoelectric properties of Si_(80)Ge_(20) materials and reach the goal of a combined figure of merit value of 0.85x10^(-3) K^(-1) averaged over a 600-1000 C temperature range. Improvement for the n-type material has been obtained by determining the optimum amounts of gallium and phosphorus dopants necessary to achieve optimum carrier mobility and concentration. The emphasis is now on the consistent reproducibility of these results through understanding and control of the hot-pressing parameters relating microstructure and composition to the transport properties. The optimum doping level has now been firmly established for p-type materials, and work is concentrating on the reduction in thermal conductivity. BN ultra fine particles have been successfully incorporated into fully dense samples and have resulted in desired improvement of the figure of merit...

Fleurial, Jean-Pierre↗
NASA NTRS2010

Oxidation Characterization of Hafnium-Based Ceramics Fabricated by Hot Pressing and Electric Field-Assisted Sintering

Ceramic borides, such as hafnium diboride (HfB2) and zirconium diboride (ZrB2), are members of a family of materials with extremely high melting temperatures referred to as Ultra High Temperature Ceramics (UHTCs). UHTCs constitute a class of promising materials for use in high temperature applications, such as sharp leading edges on future-generation hypersonic flight vehicles, because of their high melting points. The controlled development of microstructure has become important to the processing of UHTCs, with the prospect of improving their mechanical and thermal properties. The improved oxidation resistance of HfB2 has also become important if this material is to be successfully used at temperatures above 2000 C. Furthermore, the use of UHTCs on the leading edges of vehicles traveling at hypersonic speeds will mean exposure to a mixed oxidation environment comprised of both molecular and atomic oxygen. The current study has investigated the high-temperature oxidation behavior of HfB2-based materials in a pure O2 environment, as well as in environments containing different levels of dissociated oxygen (O/O2). Materials were processed by two techniques: conventional hot pressing (HP) and electric field-assisted sintering (FAS). Their oxidation behavior was evaluated in both a tube furnace at 1250 C for 3 hours and in a simulated re-entry environment in the Advanced Heating Facility (AHF) arcjet at NASA Ames Research Center, during a 10-minute exposure to a cold wall heat flux of 250W/sq cm and stagnation pressure of 0.1-0.2 atm. The microstructure of the different materials was characterized before and after oxidation using scanning electron microscopy (SEM).

Gasch, Matt↗
DOE OSTI2018

Characterization and crystallographic analyses of new three-fold Ti(O,C) nanotwins in a hot-pressed Nb-Ti-al alloy

Highlights: • Two new types of three-fold Ti(O,C) twins were observed in Nb-Ti-Al alloy. • Crystallographic relationships of the twins were analyzed in detail. • Different intersection angles derive from crystallographic operation forming twins. • Ambiguity of a 3-fold twin was clarified by the analysis of the common [011] axis. - Abstract: In this article, two new types of three-fold Ti(O,C) twins were observed, and the crystallographic relationships of the twins have been analyzed in depth. The difference in the intersection angles of primary twin boundaries derives from different crystallographic operations forming the face-centered cubic Ti(O,C) twins: two consecutive rotations of 70.5° counter-clockwise or clockwise around the [011] axis. Using double and triple Thompson tetrahedrons, the ambiguity of a three-fold twin in TEM observation is clarified by the analysis of the common [011] axis. These findings might bring about substantial insights to the crystallographic understanding of three-fold twins.

36 MATERIALS SCIENCE↗
DOE OSTI2018

B2 Grain Growth Behavior of a Ti-22Al-25Nb Alloy Fabricated by Hot Pressing Sintering

Grain growth behavior of a powder metallurgy (P/M) Ti-22Al-25Nb alloy was investigated by applying a series of isothermal treatment tests over a wide range of temperatures and holding times. An isothermal treatment scheme was conducted in the B2 phase region (1070-1110 °C) and α{sub 2} + B2 phase region (1010-1050 °C) at holding times of 10, 30 min, 1, 2, and 3 h, respectively. The effects of temperature and holding time on the microstructure evolution and microhardness of the P/M Ti-22Al-25Nb alloy at elevated temperatures were evaluated using optical microscope, scanning electron microscope, x-ray diffraction, and Vickers hardness test techniques. The results revealed that the alloy’s treated microstructure was closely linked to temperature and holding time, respectively. The change law of B2 grain growth with holding time and temperature can be well interpreted by the Beck equation and Hillert equation, respectively. The B2 grain growth exponent n and activation energy Q were acquired based on experimental data in the α{sub 2} + B2 and B2 phase regions. In addition, the grain growth contour map for the P/M Ti-22Al-25Nb alloy was constructed to depict variations in B2 grain size based on holding time and temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2013

Resolving the grain boundary and lattice impedance of hot-pressed Li 7 La 3 Zr 2 O 12 garnet electrolytes

Here, the cubic-stabilized garnet solid electrolyte with a nominal composition of Li 6.28 Al 0.24 La 3 Zr 2 O 12 is thoroughly characterized by impedance spectroscopy. By varying the frequency of the applied AC signal over 11 orders of magnitude for characterizations from –100 to +60 °C, the relative contributions of grain and grain boundary conduction are unambiguously resolved.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

First of Their Kind: Solar Cells with a Dry-Processed Perovskite Absorber Layer via Powder Aerosol Deposition and Hot-Pressing

Preparing halide perovskite films by solvent-free, powder-based processing approaches currently attracts more and more attention. However, working solar cells employing dry, powder-based halide perovskite thin films, have not been demonstrated so far. Herein, perovskite solar cells are presented where the absorber layer is prepared by transferring readily synthesized perovskite powders into a compact thin film using a fully dry-powder-processing concept. Compact thin films are deposited via an optimized powder aerosol deposition (PAD) process. Pressing at 120 °C further improves the morphology and the optoelectronic film properties. Integrating the perovskite films in a solar cell configuration results in fully working devices, with champion power conversion efficiencies of >6%. While the (optoelectronic) properties of the PAD-processed films are found to be comparable with their solution-processed counterparts, investigations of the solar cell stack suggest deterioration of the electron-transport layer properties due to the PAD process, and the presence of hydrates at the perovskite surface to be important factors that contribute to the limited solar cell efficiency. Herein, perspectives to overcome the identified limitations are outlined, emphasizing the high potential and realizability of efficient perovskite solar cells based on dry-powder-processing approaches in the future.

14 SOLAR ENERGY↗