SEARCH · Engineering Papers

Results for “Freestream Velocity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

All sources NASA NTRS DOE OSTI

NASA NTRS2015

Investigation of Spiral and Sweeping Holes

Surface infrared thermography, hotwire anemometry, and thermocouple surveys were performed on two new film cooling hole geometries: spiral/rifled holes and fluidic sweeping holes. The spiral holes attempt to induce large-scale vorticity to the film cooling jet as it exits the hole to prevent the formation of the kidney shaped vortices commonly associated with film cooling jets. The fluidic sweeping hole uses a passive in-hole geometry to induce jet sweeping at frequencies that scale with blowing ratios. The spiral hole performance is compared to that of round holes with and without compound angles. The fluidic hole is of the diffusion class of holes and is therefore compared to a 777 hole and Square holes. A patent-pending spiral hole design showed the highest potential of the non-diffusion type hole configurations. Velocity contours and flow temperature were acquired at discreet cross-sections of the downstream flow field. The passive fluidic sweeping hole shows the most uniform cooling distribution but suffers from low span-averaged effectiveness levels due to enhanced mixing. The data was taken at a Reynolds number of 11,000 based on hole diameter and freestream velocity. Infrared thermography was taken for blowing rations of 1.0, 1.5, 2.0, and 2.5 at a density ration of 1.05. The flow inside the fluidic sweeping hole was studied using 3D unsteady RANS.

infrared thermography↗

NASA NTRS2018

Toward Cooling Uniformity: Investigation of Spiral, Sweeping Holes, and Unconventional Cooling Paradigms

Surface infrared thermography, hotwire anemometry, and thermocouple surveys were performed on two new film cooling hole geometries: spiral/rifled holes and fluidic sweeping holes. Ways to quantify the efficacy of novel cooling holes that are asymmetric, not uniformly spaced or that show variation from hole to hole are presented. The spiral holes attempt to induce large-scale vorticity to the film cooling jet as it exits the hole to prevent the formation of the kidney shaped vortices commonly associated with film cooling jets. The fluidic sweeping hole uses a passive in-hole geometry to induce jet sweeping at frequencies that scale with blowing ratios. The spiral hole performance is compared to that of round holes with and without compound angles. The fluidic hole is of the diffusion class of holes and is therefore compared to a 777 hole and square holes. A patent-pending spiral hole design showed the highest potential of the nondiffusion type hole configurations. Velocity contours and flow temperature were acquired at discreet cross-sections of the downstream flow field. The passive fluidic sweeping hole shows the most uniform cooling distribution but suffers from low span-averaged effectiveness levels due to enhanced mixing. The data was taken at a Reynolds number of 11,000 based on hole diameter and freestream velocity. Infrared thermography was taken for blowing ratios of 1.0, 1.5, 2.0, and 2.5 at a density ratio of 1.05. The flow inside the fluidic sweeping hole was studied using 3D unsteady RANS. A section on ideas for future work is included that addresses issues of quantifying cooling uniformity and provides some ideas for changing the way we think about cooling such as changing the direction of cooling or coupling acoustic devices to cooling holes to regulate frequency.

Shyam, Vikram↗

NASA NTRS2019

Implementation of a Pulsed-Laser Measurement System in the National Transonic Facility

A remotely-adjustable laser transmission and imaging system has been developed for use in a high-pressure, cryogenic wind tunnel. Implementation in the National Transonic Facility has proven the system suitable for velocity and signal lifetime measurements over a range of operating conditions. The measurement system allows for the delivery of high-powered laser pulses through the outer pressure shell and into the test section interior from a mezzanine where the laser is free from environmental disturbances (such as vibrations and excessive condensation) associated with operation of the wind tunnel. Femtosecond laser electronic excitation tagging (FLEET) was utilized to provide freestream velocity measurements, and first results show typical data that may be obtained using the system herein described.

Reese, Daniel T.↗

NASA NTRS1991

Propulsion-induced aerodynamics of an ejector-configured STOVL fighter aircraft

Propulsion-induced aerodynamic effects are computed by using data obtained from tests of a full-scale model of the E-7A configuration that were run in the NASA Ames 40 x 80 and 80 x 120-foot tunnels. These effects are shown both in aerodynamic coefficients and nondimensionalized by thrust versus equivalent velocity. The test results show that the full-scale ventral nozzle-induced effects are smaller than scale model data, while the ejector-induced effects demonstrate fair agreement. The effect of tunnel test section size is primarily observed at low and static speed, high thrust conditions, as seen in comparisons of data from both tunnels. The 80 x 120-foot tunnel test gave better static thrust calibrations and permitted a greater range of test freestream velocities and angles-of-attack, extending the database provided by the full-scale model.

Poppen, William A.↗

DOE OSTI2023

High-resolution simulations of a turbulent boundary layer impacting two obstacles in tandem

High-fidelity large-eddy simulations of the flow around two rectangular obstacles are carried out at a Reynolds number of 10 000 based on the freestream velocity and the obstacle height. The incoming flow is a developed turbulent boundary layer. Mean-velocity components, turbulence fluctuations, and the terms of the turbulent-kinetic-energy budget are analyzed for three flow regimes: skimming flow, wake interference, and isolated roughness. Three regions are identified where the flow undergoes the most significant changes: the first obstacle’s wake, the region in front of the second obstacle, and the region around the second obstacle. In the skimming-flow case, turbulence activity in the cavity between the obstacles is limited and mainly occurs in a small region in front of the second obstacle. In the wake-interference case, there is a strong interaction between the freestream flow that penetrates the cavity and the wake of the first obstacle. Furthermore, this interaction results in more intense turbulent fluctuations between the obstacles. In the isolated-roughness case, the wake of the first obstacle is in good agreement with that of an isolated obstacle. Separation bubbles with strong turbulent fluctuations appear around the second obstacle.

97 MATHEMATICS AND COMPUTING↗

NASA NTRS1982

Turbulent boundary layer over solid and porous surfaces with small roughness

The wind tunnel models and instrumentation used as well as data reduction and error analysis techniques employed are described for an experimental study conducted to measure directly skin friction and obtain profiles of mean velocity, axial and normal turbulence intensity, and Reynolds stress in the untripped boundary on a large diameter axisymmetric body. Results are given for such a body with a (1) smooth, solid surface; (2) a sandpaper roughened, solid surface; (3) a sintered metal, porous surface; (4) a ""smooth'' performated titanium surface; (5) a rough, solid surface made of fine diffusion bonded screening; and (6) a rough, porous surface made of the same screening. The roughness values were in low range (k+ 5 to 7) just above what is normally considered ""hydraulically smooth''. Measurements were taken at several axial locations and tow or normal stream freestream velocities, 45.1 m/sec and 53.5 m/sec.

Kong, F. Y.↗

NASA NTRS1989

Some characteristics of bypass transition in a heated boundary layer

Experimental measurements of both mean and conditionally sampled characteristics of laminar, transitional and low Reynolds number turbulent boundary layers on a heated flat plate are presented. Measurements were obtained in air over a range of freestream turbulence intensities from 0.3 percent to 6 percent with a freestream velocity of 30.5 m/s and zero pressure gradient. Conditional sampling performed in the transitional boundary layers indicate the existence of a near-wall drop in intermittency, especially pronounced at low intermittencies. Nonturbulent intervals were observed to possess large levels of low-frequency unsteadiness, and turbulent intervals had peak intensities as much as 50 percent higher than were measured at fully turbulent stations. Heat transfer results were consistent with results of previous researchers and Reynolds analogy factors were found to be well predicted by laminar and turbulent correlations which accounted for unheated starting length. A small dependence of the turbulent Reynolds analogy factors on freestream turbulence level was observed. Laminar boundary layer spectra indicated selective amplification of unstable frequencies. These instabilities appear to play a dominant role in the transition process only for the lowest freestream turbulence level studied, however.

Sohn, K. H.↗

NASA NTRS1989

Some characteristics of bypass transition in a heated boundary layer

Experimental measurements of both mean and conditionally sampled characteristics of laminar, transitional and low Reynolds number turbulent boundary layers on a heated flat plate are presented. Measurements were obtained in air over a range of freestream turbulence intensities from 0.3 percent to 6 percent with a freestream velocity of 30.5 m/s and zero pressure gradient. Conditional sampling performed in the transitional boundary layers indicate the existence of a near-wall drop in intermittency, especially pronounced at low intermittencies. Nonturbulent intervals were observed to possess large levels of low-frequency unsteadiness, and turbulent intervals had peak intensities as much as 50 percent higher than were measured at fully turbulent stations. Heat transfer results were consistent with results of previous researches and Reynolds analogy factors were found to be well predicted by laminar and turbulent correlations which accounted for unheated starting length. A small dependence of the turbulent Reynolds analogy factors on freestream turbulence level was observed. Laminar boundary layer spectra indicated selective amplification of unstable frequencies. These instabilities appear to play a dominant role in the transition process only for the lowest freestream turbulence level studied, however.

Sohn, K. H.↗

NASA NTRS2017

Stabilization of Hypersonic Boundary Layers by Linear and Nonlinear Optimal Perturbations

The effect of stationary, finite-amplitude, linear and nonlinear optimal perturbations on the modal disturbance growth in a Mach 6 axisymmetric flow over a 7 deg. half-angle cone with 0:126 mm nose radius and 0:305 m length is investigated. The freestream parameters (M = 6, Re(exp 1) = 18 x 10(exp. 6) /m) are selected to match the flow conditions of a previous experiment in the VKI H3 hypersonic tunnel. Plane-marching parabolized stability equations are used in conjunction with a partial-differential equation based planar eigenvalue analysis to characterize the boundary layer instability in the presence of azimuthally periodic streaks. The streaks are observed to stabilize nominally planar Mack mode instabilities, although oblique Mack mode and first-mode disturbances are destabilized. Experimentally measured transition onset in the absence of any streaks correlates with an amplification factor of N = 6 for the planar Mack modes. For high enough streak amplitudes, the transition threshold of N = 6 is not reached by the Mack mode instabilities within the length of the cone; however, subharmonic first-mode instabilities, which are destabilized by the presence of the streaks, do reach N = 6 near the end of the cone. The highest stabilization is observed at streak amplitudes of approximately 20 percent of the freestream velocity. Because the use of initial disturbance profiles based on linear optimal growth theory may yield suboptimal control in the context of nonlinear streaks, the computational predictions are extended to nonlinear optimal growth theory. Results show that by using nonlinearly optimal perturbation leads to slightly enhanced stabilization of plane Mack mode disturbances as well as reduced destabilization of subharmonic first-mode disturbances.

Incompressible boundary layer↗

DOE OSTI2023

Quasi-Steady Simulation of Glaze Ice Accretion and Heat Transfer in the Supercooled Large Droplet Regime in Atmospheric Turbulent Air Flow

Abstract To avoid the use of a computationally intensive full unsteady simulation while providing an accurate solution, a quasi-steady simulation has been performed to study glaze and mixed ice accretion in the supercooled large droplet (SLD) regime in turbulent flow of atmospheric air. We have attempted to find the minimum time-step necessary to adequately simulate the icing process on an airfoil surface. Based on node displacement, a mesh morphing scheme has been adopted in the computations to account for the moving boundaries that are caused by the continuous ice buildup. We have modeled ice accretion on an airfoil surface for a time period of 232 s using several time steps. At each time-step we solved the steady-state conservation equations for the air and droplet phases and then used the results as initial conditions for the next time position. The magnitude of the time-step ranged from a least accurate two-shot simulation (where the time-step is 116 s) to a most accurate 2320-shot simulation (where the time-step is 0.1 s). In-between these two extreme time steps, we have performed a three-shot simulation (where the time-step is 77.33 s), a four-shot simulation (where the time-step is 58 s), a six-shot simulation (where the time-step is 38.67 s), a 46-shot simulation (where the time-step is 5 s), and a 232-shot simulation (where the time-step is 1 s). We have done so to find out the degree of accuracy (or inaccuracy) of the multishot simulation approach and to find out the appropriate time-step needed for a successful and valid quasi-steady simulation. A valid quasi-steady simulation needs to use a time-step that is small enough to reproduce the full time-dependent solution within a very small error band. We have found that both the 1 s and the 0.1 s time steps produce virtually identical results. This is the primary litmus test that proves the validity of the quasi-steady-state assumption. The results adopted in this paper are thus all based on the more conservative 0.1 s time-step. In the process of performing the simulations, remeshing was required in order to maintain the grid density in zones of high curvature to be able to capture the full physics in those zones. After successfully modeling glaze ice accretion over the airfoil surface using the 0.1 s quasi-steady simulation approach, the effects of supercooled large droplets (SLDs) impacting the surface have been examined and presented in terms of the variation of the local collection efficiency, the water film thickness, and the heat transfer rate. Examination of the variation of the angle that the ice horn makes with the airfoil chord line demonstrated a 20% improvement in angle prediction when the time-step is reduced from 116 s to 0.1 s. The analysis also reveals a 12% or 8.5% increase in the maximum collection efficiency, βmax, depending on whether the value of the liquid water content (LWC) has been doubled from 0.5 g/m3 to 1 g/m3, or the value of the freestream velocity has been doubled from 75 m/s to 150 m/s, respectively. Because of the need to monitor the local collection efficiency and convective heat fluxes at each shot (regardless of the number of shots employed), the approach adopted here was found to be effective in successively and successfully reproducing the curvature of the glaze ice horn.

Engineering↗

DOE OSTI2025

Observations of wind farm wake recovery at an operating wind farm

Abstract. The interplay of momentum surrounding wind farms significantly influences wake recovery, affecting the speed at which wakes return to their freestream velocities. Under stable atmospheric conditions, wind farm wakes can extend over considerable distances, leading to sustained vertical momentum flux downstream, with variations observed throughout the diurnal cycle. Particularly in regions such as the US Great Plains, stable conditions can induce low-level jets (LLJs), impacting wind farm performance and power output. This study examines the implications of wake recovery using long-term observations of vertical momentum flux profiles across diverse atmospheric conditions. In these observations, several key findings were observed, such as (a) LLJ heights being altered downstream of a wind farm, especially when the LLJs are below 250 m above ground level; (b) a notable impact of LLJ height on wake recovery being observed using momentum flux profiles at upwind and downwind locations, wherein LLJs between 250 and 500 m above ground level resulted in larger momentum transfer within the wake (i.e., smaller velocity deficit) compared to LLJs below 250 m above ground level; (c) the largest momentum flux variability being observed during stable atmospheric conditions, with non-negligible variability observed during neutral and unstable atmospheric conditions; (d) detection of wake effects almost always being observed throughout the atmospheric boundary layer height; and finally (e) enhancement of wake recovery being observed in the presence of propagating gravity waves. These insights deepen our understanding of the intricate dynamics governing wake recovery in wind farms, advancing efforts to model and predict their behavior across varying atmospheric contexts. In addition, the performance of large-eddy-simulation-based semi-empirical internal boundary layer height model estimates incorporating real-world atmospheric and turbine inputs was evaluated using observations during LLJ conditions.

17 WIND ENERGY↗

NASA NTRS1973

Penetration of retrorocket exhausts into subsonic counterflows.

Simulation experiments were performed in the NASA Langley Full Scale Tunnel to investigate the retroplume heating rates encountered by a lander vehicle during a terminal descent to a planetary surface. A 10% scale model of the Viking Lander with freestream velocity conditions from 37 to 75 ft/sec was used for simulation. The simulation test data were close to the theoretical predictions of Hill et al. (1971).

Jarvinen, P. O.↗

NASA NTRS1974

Shock shapes of blunt bodies in hypersonic helium, air, and CO2 flows

A primary factor governing hypersonic flowfield characteristics of blunt vehicles entering planetary atmospheres is the normal shock density ratio. Hence, a means of duplicating or simulating the high density ratios experienced during planetary entry is needed. One facility having the capability of generating a range of hypersonic-hypervelocity flow conditions in arbitrary test gases is the expansion tube. Preliminary shock shape results obtained in the Langley 6-in. expansion tube at hypersonic conditions are presented. Normal shock density ratios from approximately 4 to 19 were generated using helium, air, and CO2 test gases at freestream velocities from 5 to 7 km/sec. Test models were a flat-faced cylinder and the Viking aeroshell.

Miller, C. G.↗

NASA NTRS1975

Potential and viscous flow in VTOL, STOL or CTOL propulsion system inlets

A method was developed for analyzing the flow in subsonic axisymmetric inlets at arbitrary conditions of freestream velocity, incidence angle, and inlet mass flow. An improved version of the method is discussed and comparisons of results obtained with the original and improved methods are given. Comparisons with experiments are also presented for several inlet configurations and for various conditions of the boundary layer from insignificant to separated. Applications of the method are discussed, with several examples given for specific cases involving inlets for VTOL lift fans and for STOL engine nacelles.

Stockman, N. O.↗

NASA NTRS1975

Internal cowl-separation at high incidence angles

Internal flow separation at large incidence angles is studied on the basis of wind-tunnel pressure data for six axisymmetric inlet geometries. The inlet geometric variables investigated are the angle of incidence, the throat Mach number, the internal lip contraction ratio, 'sharpness' of the external shape, and freestream velocity. It is shown that an increase in lip contraction ratio delays internal flow separation, while an increase in the sharpness of the external profile tends to reduce the angle of incidence at which complete flow separation occurs. It is also shown that inlet flow separation is subject to scale effects associated with the boundary layer on the cowl surface. The scale effects are particularly pronounced at very high throat Mach numbers.

Jakubowski, A. K.↗

NASA NTRS1975

Potential and viscous flow in VTOL, STOL or CTOL propulsion system inlets

A method has been developed for analyzing the flow in subsonic axisymmetric inlets at arbitrary conditions of freestream velocity, incidence angle, and inlet mass flow. An improved version of the method is discussed and comparisons of results obtained with the original and improved methods are given. Comparisons with experiments are also presented for several inlet configurations and for various conditions of the boundary layer from insignificant to separated. The paper discusses applications of the method, with several examples given for specific cases involving inlets for VTOL lift fans and for STOL engine nacelles.

Stockman, N. O.↗

NASA NTRS1976

Turbine vane gas film cooling with injection in the leading edge region from a single row of spanwise angled holes

An experimental study of gas film cooling was conducted on a 3X size model turbine vane. Injection in the leading edge region was from a single row of holes angled in a spanwise direction. Measurements of the local heat flux downstream from the row of coolant holes, both with and without film coolant flow, were used to determine the film cooling performance presented in terms of the Stanton number ratio. Results for a range of coolant blowing ratio, M = 0 to 2.0, indicate a reduction in heat flux of up to 15 to 30 percent at a point 10 to 11 hole diameters downstream from injection. An optimum coolant blowing ratio corresponds to a coolant-to-freestream velocity ratio in the range of 0.5. The shallow injection angle resulted in superior cooling performance for injection closest to stagnation, while the effect of injection angle was insignificant for injection further from stagnation.

Lecuyer, M. R.↗

NASA NTRS1975

Quiet Clean Short-Haul Experimental Engine (QCSEE) aerodynamic characteristics of 30.5 centimeter diameter inlets

A low speed test program was conducted in a 9- by 15-foot V/STOL wind tunnel to investigate internal performance characteristics and determine key design features required for an inlet to meet the demanding operational conditions of the QCSEE application. Four models each having a design average throat Mach number of 0.79 were tested over a range of incidence angle, throat Mach number, and freestream velocity. Principal design variable was internal lip diameter ratio. Stable, efficient inlet performance was found to be feasible at and beyond the 50 deg incidence angle required by the QCSEE application at its 41.2 m/sec (80 knot) nominal takeoff velocity, through suitably designed inlet lip and diffuser components. Forebody design was found to significantly impact flow stability via nose curvature. Measured inlet wall pressures were used to select a location for the inlet throat Mach number control's static pressure port that properly balanced the conflicting demands of relative insensitivity to flow incidence and sufficiently high response to changes in engine flow demand.

Paul, D. L.↗