Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FLIGHT ALTITUDE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Exhaust emission calibration of two J-58 afterburning turbojet engines at simulated high-altitude, supersonic flight conditions

Emissions of total oxides of nitrogen, nitric oxide, unburned hydrocarbons, carbon monoxide, and carbon dioxide from two J-58 afterburning turbojet engines at simulated high-altitude flight conditions are reported. Test conditions included flight speeds from Mach 2 to 3 at altitudes from 16.0 to 23.5 km. For each flight condition exhaust measurements were made for four or five power levels, from maximum power without afterburning through maximum afterburning. The data show that exhaust emissions vary with flight speed, altitude, power level, and radial position across the exhaust. Oxides of nitrogen emissions decreased with increasing altitude and increased with increasing flight speed. Oxides of nitrogen emission indices with afterburning were less than half the value without afterburning. Carbon monoxide and hydrocarbon emissions increased with increasing altitude and decreased with increasing flight speed. Emissions of these species were substantially higher with afterburning than without.

Holdeman, J. D.↗
NASA NTRS2020

Autonomous Assessment and Predictive Capabilities for Low-Altitude Urban Flight Operations

The integration of unmanned aerial vehicles in the national airspace will introduce new vehicle types, technologies, and operational paradigms for which safety must be maintained and hazards mitigated. One approach is to attempt to design for possible hazards and unsafe incidents that can occur at different phases of flight (pre-flight, in-flight, and post-flight) and during ground operations. Another is to mitigate safety incidents by implementing changes to policies, procedures, regulations, and design to cover personnel, equipment, and aircraft during operations. These and other techniques, not described herein, are typically conservative or adhoc in that they reduce the likelihood of risk after safety incidents have occurred. In this work, the goal is to develop a more predictive capability to monitor and mitigate risk and hazards to safety “in-time” enough for decisions to be made. In line with NASA’s Aeronautics Mission Directorate Strategic Thrust 5 [1] (In-Time System-Wide Safety Assurance), the System-Wide Safety (SWS) project under which this work falls, is developing and demonstrating innovative and safety-oriented solutions that enable modernization and aviation transformation. To that effect, this work will detail data-driven efforts on the SWS project to develop a number of safety-critical services for in-time monitoring and mitigation of hazards to low-altitude flight operations. First, hazards to these operations are identified based on previous work by NASA [2,3] and others in the aerospace industry. These hazards include (i) unsafe proximity to other vehicles, property, and people on the ground, (ii) critical system failures such as communication signal/GPS loss, unexpected propulsion system degradation, engine/power failure, and (iii) operational/environmental issues such as severe weather and gusty winds. For these hazards, safety metrics, which can be quantified and assessed are defined, models to monitor and predict them are developed, and flight test data is generated to develop, validate, and test these models, considering the complex interplay of the different hazards that define them [4-6]. In addition, the uncertainty in the non-deterministic effects that cannot be modeled nor predicted and unknown unknowns that arise after design/testing and during operations must be handled in rigorous manner. As a result, for each of the developed safety metrics, their dependencies on one another are characterized and a framework for handling the uncertainties inherent in the modeling, algorithms, and measurements required for prediction is also developed [7]. To that effect, this presentation will describe the safety metrics and services already developed and underway under the System-Wide Safety project that utilize data-driven techniques for the identification of anomalies, precursors, and trends (APTs) to monitor and mitigate hazards to safety, in-time, for urban flight operations in low-altitude airspace.

Okolo, Wendy A.↗
NASA NTRS1981

On-line optimization of aircraft altitude and flight path angle dynamics

The optimization of aircraft altitude and flight path angle dynamics is addressed in a form suitable for on-line computation and control. The approach here is a direct extension of the work reported by Calise (1979), where singular perturbation methods were used to optimize position, energy and heading dynamics; it thus represents an optimal control solution that models all of the primary trajectory related dynamics. It is pointed out that the resulting algorithm can be regarded as a nonlinear feedback control law. The minimum time intercept of a fixed terminal point is used in setting the framework in which the analytical results are developed. The main theoretical result is that the dynamics, while not completely separable, can be approximated by singular perturbation methods when the control model includes relative position dynamics.

Calise, A. J.↗
NASA NTRS1991

Computer aiding for low-altitude helicopter flight

A computer-aiding concept for low-altitude helicopter flight was developed and evaluated in a real-time piloted simulation. The concept included an optimal control trajectory-generated algorithm based on dynamic programming, and a head-up display (HUD) presentation of a pathway-in-the-sky, a phantom aircraft, and flight-path vector/predictor symbol. The trajectory-generation algorithm uses knowledge of the global mission requirements, a digital terrain map, aircraft performance capabilities, and advanced navigation information to determine a trajectory between mission waypoints that minimizes threat exposure by seeking valleys. The pilot evaluation was conducted at NASA Ames Research Center's Sim Lab facility in both the fixed-base Interchangeable Cab (ICAB) simulator and the moving-base Vertical Motion Simulator (VMS) by pilots representing NASA, the U.S. Army, and the U.S. Air Force. The pilots manually tracked the trajectory generated by the algorithm utilizing the HUD symbology. They were able to satisfactorily perform the tracking tasks while maintaining a high degree of awareness of the outside world.

Swenson, Harry N.↗
NASA NTRS1991

Computer aiding for low-altitude helicopter flight

A computer-aiding concept for low-altitude helicopter flight was developed and evaluated in a real-time piloted simulation. The concept included an optimal control trajectory-generated algorithm based on dynamic programming, and a head-up display (HUD) presentation of a pathway-in-the-sky, a phantom aircraft, and flight-path vector/predictor symbol. The trajectory-generation algorithm uses knowledge of the global mission requirements, a digital terrain map, aircraft performance capabilities, and advanced navigation information to determine a trajectory between mission waypoints that minimizes threat exposure by seeking valleys. The pilot evaluation was conducted at NASA Ames Research Center's Sim Lab facility in both the fixed-base Interchangeable Cab (ICAB) simulator and the moving-base Vertical Motion Simulator (VMS) by pilots representing NASA, the U.S. Army, and the U.S. Air Force. The pilots manually tracked the trajectory generated by the algorithm utilizing the HUD symbology. They were able to satisfactorily perform the tracking tasks while maintaining a high degree of awareness of the outside world.

Swenson, Harry N.↗
NASA NTRS1983

A study of altitude and flight path angle dynamics for a singularly perturbed fuel optimization problem

This short paper will demonstrate that the separation of altitude and flight path angle dynamics using singular perturbation techniques for a transport fuel optimization problem results in an unacceptable oscillation in altitude. A technique for damping this oscillation by adding a penalty term to the cost function for the optimization problem will be discussed. This technique will be compared with a different approach that linearizes the altitude and flight path angle boundary layers.

Price, D. B.↗
NASA NTRS1956

Combustion Limits and Efficiency of Turbojet Engines

Combustion must be maintained in the turbojet-engine combustor over a wide range of operating conditions resulting from variations in required engine thrust, flight altitude, and flight speed. Furthermore, combustion must be efficient in order to provide the maximum aircraft range. Thus, two major performance criteria of the turbojet-engine combustor are (1) operatable range, or combustion limits, and (2) combustion efficiency. Several fundamental requirements for efficient, high-speed combustion are evident from the discussions presented in chapters III to V. The fuel-air ratio and pressure in the burning zone must lie within specific limits of flammability (fig. 111-16(b)) in order to have the mixture ignite and burn satisfactorily. Increases in mixture temperature will favor the flammability characteristics (ch. III). A second requirement in maintaining a stable flame -is that low local flow velocities exist in the combustion zone (ch. VI). Finally, even with these requirements satisfied, a flame needs a certain minimum space in which to release a desired amount of heat, the necessary space increasing with a decrease in pressure (ref. 1). It is apparent, then, that combustor design and operation must provide for (1) proper control of vapor fuel-air ratios in the combustion zone at or near stoichiometric, (2) mixture pressures above the minimum flammability pressures, (3) low flow velocities in the combustion zone, and (4) adequate space for the flame.

Barnett, H. C.↗
NASA NTRS1979

Active external store flutter suppression in the YF-17 flutter model

A single activated trailing-edge (T.E.) control system (spanning 7% of each wing) is applied to the YF-17 flutter model with the object of suppressing the external store flutter of three different store configurations. The control law is derived by the use of the aerodynamic energy concept and its gains are maintained constant for all three configurations. The results obtained show that the activated T.E. control system leads to very significant increases in the flutter dynamic pressures Q(DF) of all three configurations; these increases range between 160-240% increase in Q(DF). These increases in Q(DF) are maintained over a very wide range of flight altitudes and flight velocities.

Nissim, E.↗
NASA NTRS1990

Structure-borne noise estimates for the PTA aircraft

Estimates of the level of in-flight structure-borne noise transmission in the Propfan Test Assessment Aircraft were carried out for the first three blade passage frequencies. The procedure used combined the frequency response functions of wing strain to cabin sound pressure level (SPL) response obtained during ground test with in-flight measured wing strain response data. The estimated cabin average in-flight structure-borne noise levels varied from 64 to 84 dB, with an average level of 74 dB. The estimates showed little dependence on engine/propeller power, flight altitude, or flight Mach number. In general, the bare cabin noise levels decreased with increasing propeller tone, giving rise to a plausible structure-borne noise transmission problem at the higher blade passage tones. Without knowledge of the effects of a high insertion loss side wall treatment on structure-borne noise transmission, no quantitative conclusions could be made.

Unruh, James F.↗
NASA NTRS1989

Computational aerothermodynamics

Computational aerothermodynamics concerns the coupling of real gas effects with equations of motion to include thermochemical rate processes for chemical and energy exchange phenomena. These processes concern the creation and destruction of gas species by chemical reactions and the transfer of energy between the various species and between the various energy modes (e.g., translation, rotation, vibration, ionization, dissociation/recombination, etc.) of the species. To gain some insight into when such phenomena occur for current and future aerospace flight vehicles the author shows the flight regimes of some typical vehicles (e.g., Concord, aerospace plane, Space Shuttle, associated space transfer vehicles, Apollo entry vehicle, etc.) in terms of flight altitude and flight speed. Also indicated are regimes where chemical reactions such as dissociation and ionization are important and where nonequilibrium thermochemical phenomena are important.

Deiwert, George S.↗
NASA NTRS2002

A Lighter-Than-Air System Enhanced with Kinetic Lift

A hybrid airship system is proposed in which the buoyant lift is enhanced with kinetic lift. The airship would consist of twin hulls in which the buoyant gas is contained. The twin hulls would be connected in parallel by a wing having an airfoil contour. In forward flight, the wing would provide kinetic lift that would add to the buoyant lift. The added lift would permit a greater payload/altitude combination than that which could be supported by the buoyant lift alone. The buoyant lift is a function of the volume of gas and the flight altitude. The kinetic lift is a function of the airfoil section, wing area, and the speed and altitude of flight. Accordingly there are a number of factors that can be manipulated to arrive at a particular design. Particular designs could vary from small, lightweight systems to very large, heavy-load systems. It will be the purpose of this paper to examine the sensitivity of such a design to the several variables. In addition, possible uses made achievable by such a hybrid system will be suggested.

Spearman, M. Leroy↗
NASA NTRS1991

Simulation evaluation of a low-altitude helicopter flight guidance system adapted for a helmet-mounted display

A computer aiding concept for low-altitude helicopter flight has been developed and evaluated in a real-time piloted simulation. The concept included an optimal control trajectory-generation algorithm based upon dynamic programming, and a helmet-mounted display (HMD) presentation of a pathway-in-the-sky, a phantom aircraft, and flight-path vector/predictor guidance symbology. The pilot evaluation was conducted at the NASA-Ames Research Center moving base vertical motion simulator (VMS) by pilots representing NASA, the US Army, Air Force, and helicopter industry. The pilot manually tracked the trajectory generated by the algorithm utilizing the HMD symbology. The pilots were able to satisfactorily perform the tracking tasks while maintaining a high degree of awareness of the outside world.

Swenson, Harry N.↗
NASA NTRS1992

Simulation evaluation of a low-altitude helicopter flight guidance system adapted for a helmet-mounted display

A computer aiding concept for low-altitude helicopter flight was developed and evaluated in a real-time piloted simulation. The concept included an optimal control trajectory-generation algorithm based upon dynamic programming and a helmet-mounted display (HMD) presentation of a pathway-in-the-sky, a phantom aircraft, and flight-path vector/predictor guidance symbology. The trajectory-generation algorithm uses knowledge of the global mission requirements, a digital terrain map, aircraft performance capabilities, and advanced navigation information to determine a trajectory between mission way points that seeks valleys to minimize threat exposure. The pilot evaluation was conducted at NASA ARC moving base Vertical Motion Simulator (VMS) by pilots representing NASA, the U.S. Army, the Air Force, and the helicopter industry. The pilots manually tracked the trajectory generated by the algorithm utilizing the HMD symbology. The pilots were able to satisfactorily perform the tracking tasks while maintaining a high degree of awareness of the outside world.

Swenson, Harry N.↗
DOE OSTI2023

Report on ISR-1 High-Altitude Balloon Flight

To test small technologies at lower cost for space science applications, LANL has developed a small high altitude balloon payload that could, in the future, be regularly and inexpensively launched from LANL. A neutron detector, NEMO, was integrated to evaluate its performance in a space-like mixed-radiation environment and collect neutron data in the atmosphere. In collaboration with EES-14, a high-altitude balloon payload was launched from LANL Technical Area 51 on February 27, 2023 and April 17, 2023. For real-time geolocation, a SAM-M8Q M8 GNSS module was used to get position and time, and an Iridium RockBLOCK 9603 was used to communicate with the ground using the Iridium satellite fleet. These modules were all controlled using an Iteaduino Mega microcontroller board. Finally, a High Altitude Science Eagle Flight Computer with a temperature pressure sensor ran independently, writing data to an SD card. All of these modules were powered by a 5 mAh lithium polymer battery. The battery was attached to the bottom of the payload while the remaining electronics were embedded in the underside of the top of the payload. These modules were wired as seen in Figure 1-2. The Iteaduino Mega microcontroller board was programmed to use the RockBLOCK to send a message once every 10 minutes containing neutron and GPS data read off the NEMO and SAM M8Q, respectively. Once the message send attempt finished, the RockBLOCK would be slept for the rest of the 10 minute interval. The Eagle Flight Computer ran continuously throughout the flight, taking data every 6 seconds. The RockBLOCK message data was set up to be delivered from the Iridium satellite fleet to a website, where it was stored and parsed to create live maps and plots for analysis and balloon retrieval. The RockBLOCK message data was additionally configured to be sent to an email as a fail-safe. The payload was ground-tested successfully for over 50 hours, with multiple revisions occurring to best prepare for conditions at altitude and improve the software and firmware to fix any issues that cropped up with the data pipeline. Additional to the balloon payload, the flight had an attached iMet-4 radiosonde and Garmin T5 GPS Dog Collar. The radiosonde provided GPS and meteorological data. The T5 dog collar is used along with a Garmin Astro 430 to track the balloon at a range of up to 9 miles for retrieval. The balloon itself was initially a 1600 g meteorological balloon with an attached High Altitude Science parachute, both of which can be seen in Figure 1-3. After the first flight, the EES team swapped to a Rocketman parachute.

42 ENGINEERING↗
NASA NTRS1988

Optimal plane change during constant altitude hypersonic flight

Future spacecraft operating in the vicinity of the earth may have resort to the atmosphere as an aid in effecting orbital change. While a previous treatment of this technique chose constant altitude, speed, and angle-of-attack values in order to maximize the plane change for a fixed amount of propellant consumption during hypersonic flight, the former two parameters are presently released from the constraint of constancy. The general characteristics of the optimal controls are described on the basis of the domain of maneuverability, and numerical solutions are obtained for several specific cases. Under the condition of constant-altitude flight, it is generally not optimal to fly at constant angle-of-attack.

Mease, K. D.↗