SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
High enthalpy arc tunnel at Langley Research Center for simulating aerodynamic heating and forces during spacecraft reentry
Uniform flow and wall boundary layer growth measurement in conical nozzle of reflected shock tunnel operating at high enthalpy conditions
High enthalpy shock tube and nozzle gas flows for incident shock Mach numbers analyzed for laminar boundary layers and boundary layer transitions
Enthalpy probe, mass flow measuring system, and flow meter calibration system designs
A method is presented for integrating numerically the equations of motion for a compressible free shear layer developing from a boundary-layer profile of arbitrary shape. Sutherland's law is used to determine the coefficient of viscosity and the Prandtl number is taken as 0.72. Calculated results are reported for free-stream Mach numbers ranging from 0 to 10 and for stagnation-enthalpy ratios ranging from 0 to 5.0. The effects of varying the initial boundary-layer profile and of a discontinuity in temperature at the origin are also studied. The results include graphs showing the development of dividing-streamline velocity, of local Nusselt number, and of dividing-streamline location.
Heat capacity and enthalpy of mixing of Hg(1-x)Cd(x)Te pseudobinary melts were calculated assuming an associated solution model for the liquid phase. The thermal conductivity of the pseudobinary melts for x = 0, 0.05, 0.1, and 0.2 was then calculated from the heat capacity values and the experimental values of thermal diffusivity and density for these melts. The thermal conductivity for the pseudobinary solid solution is also discussed.
The generalized chemistry version of the computer code SPARK is extended to include two higher-order numerical schemes, yielding fourth-order spatial accuracy for the inviscid terms. The new and old formulations are used to study the influences of finite rate chemical processes on nozzle performance. A determination is made of the computationally optimum reaction scheme for use in high-enthalpy nozzles. Finite rate calculations are compared with the frozen and equilibrium limits to assess the validity of each formulation. In addition, the finite rate SPARK results are compared with the constant ratio of specific heats (gamma) SEAGULL code, to determine its accuracy in variable gamma flow situations. Finally, the higher-order SPARK code is used to calculate nozzle flows having species stratification. Flame quenching occurs at low nozzle pressures, while for high pressures, significant burning continues in the nozzle.
Composites of ceramic powders in epoxies appropriate for both insulating and impregnating NbTi windings are studied. Specific heat, thermal conductivity, thermal contraction, and magnetocaloric measurements on composites are presented. Thermal contractions well matched to copper are found and thermal shock resistance is greatly enhanced. Enthalpies, 4.2-6 K, range up to 80 mJ/cu cm and are 20-50 times larger than that of the pure epoxies. Results are not specific to the epoxies used but apply to composites with any amorphous matrices.
The present paper describes recent advances and trends in finite element developments and applications for solidification problems. In particular, in comparison to traditional methods of approach, new enthalpy-based architectures based on a generalized trapezoidal family of representations are presented which provide different perspectives, physical interpretation and solution architectures for effective numerical simulation of phase change processes encountered in solidification problems. Various numerical test models are presented and the results support the proposition for employing such formulations for general phase change applications.
A complete analysis of the melting-ablator governing equations is carried out for porous ablators with the purpose of establishing an approximate analytical model capable of determining surface recession, temperature, and heat flux as well as in-depth temperature profiles. A detailed dimensional analysis of the melt-flow governing equations is performed for parameters applicable to high-enthalpy flows. Results of arc-jet flow experiments performed on NASA Reusable Surface Insulation materials of different densities and over a range of stagnation pressures and heat fluxes are discussed. A dimensionless correlation for melt run-offs is derived in terms of material and flow parameters; however, it is pointed out that the accuracy of the current data is sufficient to conclude the compliance with the model.
Planar laser-induced fluorescence (PLIF) measurements of property fields in a high-enthalpy, supersonic, underexpanded free jet generated in a reflection-type shock tunnel are reported. PLIF images showing velocity and temperature sensitivity are presented. The inferred radial velocity and relative rotational temperature fields are found to be in agreement with those predicted by a numerical simulation of the flowfield using the method of characteristics.
A numerical methodology is presented for simulating the time-dependent reacting flow inside the entire length of high enthalpy pulse facilities. The methodology is based on a finite-volume TVD scheme for the quasi-1D Euler equations coupled with finite-rate chemistry. A moving mesh and tracking of gas interfaces are used to overcome certain numerical difficulties associated with these types of flows. Simulation results of a helium driven shock tube show that computations can be used to predict the off-tailored behavior of shock tubes and tunnels. Particular attention is given to computations of the flow through the NASA Ames 16-inch combustion driven shock tunnel which show the influence of nonuniformities in the driver section on the reservoir conditions; and the effect of finite secondary diaphragm opening times on the chemical composition of the test flow in the HYPULSE expansion tube.
A typical inlet axial-flow compressor inlet stage, which was designed on the basis of constant total enthalpy with symmetrical velocity diagram at all radii, was investigated. At a tip speed of 1126 feet per second, a peak pressure ratio of 1.28 was obtained at an efficiency of 0.76. At a tip speed, the highest practical flow was 28 pounds per second per square foot frontal area with an efficiency of 0.78. Data for a rotor relative inlet Mach number range of from 0.5 to 0.875 indicates that the critical value for any stage radial element is approximately 0.80 for the stage investigated.
Our study investigates the steady secondary streaming that occurs in the pulse tube refrigerator through application of the conservation laws and support by flow visualization experiments. A series expansion of the mass, momentum and energy conservation laws for an axisymmetric system yields a set of linear differential equations. The series solution is expanded in the small parameter epsilon = 1/Str where Str is the Strouhal number. The O(1) basic flow problem is solved for the case of a compressible ideal gas oscillating within a cylindrical tube. The phase and amplitude of the boundary conditions on axial velocity are treated as independent parameters. The basic solution for the gas domain is solved for the case of temperature and heat flux coupling to the tube wall. The temperature coupled solution shows how the Fourier number of the tube wall affects the gas temperature, phase angle, and time-averaged enthalpy flow. The basic solution is also examined for the time-averaged Reynolds stresses which are shown to be the driving force that produces steady secondary momentum streaming. Calculated solutions to the steady momentum streaming are shown to be in qualitative agreement with flow visualization experiments.
The proposed paper will present a numerical investigation of the flow characteristics and boundary layer development in the nozzles of high enthalpy shock tunnel facilities used for hypersonic propulsion testing. The computed flow will be validated against existing experimental data. Pitot pressure data obtained at the entrance of the test cabin will be used to validate the numerical simulations. It is necessary to accurately model the facility nozzles in order to characterize the test article flow conditions. Initially the axisymmetric nozzle flow will be computed using a Navier Stokes solver for a range of reservoir conditions. The calculated solutions will be compared and calibrated against available experimental data from the DLR HEG piston-driven shock tunnel and the 16-inch shock tunnel at NASA Ames Research Center. The Reynolds number is assumed to be high enough at the throat that the boundary layer flow is assumed turbulent at this point downstream. The real gas affects will be examined. In high Mach number facilities the boundary layer is thick. Attempts will be made to correlate the boundary layer displacement thickness. The displacement thickness correlation will be used to calibrate the quasi-1D codes NENZF and LSENS in order to provide fast and efficient tools of characterizing the facility nozzles. The calibrated quasi-1D codes will be implemented to study the effects of chemistry and the flow condition variations at the test section due to small variations in the driver gas conditions.
The NASA Ames Research Center (ARC) Arc Jet Facilities' Aerodynamic Heating Facility (AHF) has been instrumented for the Enthalpy By Energy Balance (EB2) method. Diagnostic EB2 data is routinely taken for all AHF runs. This paper provides an overview of the EB2 method implemented in the AHF. The chief advantage of the AHF implementation over earlier versions is the non-intrusiveness of the instruments used. For example, to measure the change in cooling water temperature, thin film 1000 ohm Resistance Temperature Detectors (RTDs) are used with an Anderson Current Loop (ACL) as the signal conditioner. The ACL with 1000 ohm RTDs allows for very sensitive measurement of the increase in temperature (Delta T) of the cooling water to the arc heater, which is a critical element of the EB2 method. Cooling water flow rates are measured with non-intrusive ultrasonic flow meters.
A new computer program to design nozzles with non-uniform idow has been developed using the rotational method of characteristics (MOC). This program has been used to design a nozzle for the NASA's HYPULSE shock-expansion tunnel for use in scramjet engine tests at a Mach-15 flight-enthalpy condition. The nozzle has an area ratio of 9.5:l that expands the inflow from Mach 6 along the centerline to Mach 8.7. Although the density and Mach number vary radially at the exit due to the non-uniformities of the inflow, the MOC procedure produces exit flow that is parallel and has uniform static pressure. The design has been verified with CFD which compares favorably with the MOC solution.
A new computer program to design nozzles with non-uniform inflow has been developed using the rotational method of characteristics (MOC). This program has been used to design a nozzle for the NASA's HYPULSE shock-expansion tunnel for use in scramjet engine tests at a Mach-15 flight-enthalpy condition. The nozzle has an area ratio of 9.5:1 that expands the inflow from Mach 6 along the centerline to Mach 8.7. Although the density and Mach number vary radially at the exit due to the non-uniformities of the inflow, the MOC procedure produces exit flow that is parallel and has uniform static pressure. The design has been verified with CFD which compares favorably with the MOC solution.