Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Engineering Analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

EDIN design study alternate space shuttle booster replacement concepts. Volume 1: Engineering analysis

The use of a recoverable liquid rocket booster (LRB) system to replace the existing solid rocket booster (SRB) system for the shuttle was studied. Historical weight estimating relationships were developed for the LRB using Saturn technology and modified as required. Mission performance was computed using February 1975 shuttle configuration groundrules to allow reasonable comparison of the existing shuttle with the study designs. The launch trajectory was constrained to pass through both the RTLS/AOA and main engine cut off points of the shuttle reference mission 1. Performance analysis is based on a point design trajectory model which optimizes initial tilt rate and exoatmospheric pitch profile. A gravity turn was employed during the boost phase in place of the shuttle angle of attack profile. Engine throttling add/or shutdown was used to constrain dynamic pressure and/or longitudinal acceleration where necessary. Four basic configurations were investigated: a parallel burn vehicle with an F-1 engine powered LRB; a parallel burn vehicle with a high pressure engine powered LRB; a series burn vehicle with a high pressure engine powered LRB. The relative sizes of the LRB and the ET are optimized to minimize GLOW in most cases.

Demakes, P. T.↗
NASA NTRS1947

Altitude-Wind-Tunnel Investigation of the 19B-2, 19B-8 and 19XB-1 Jet- Propulsion Engines: Analysis of Compressor Performance - 4

Investigations were conducted in the Cleveland altitude wind tunnel to determine the performance and operational characteristics of the 19B-2, 19B-8, and 19XS-1 turbojet engines. One objective was to determine the effect of altitude, flight Mach number, and tail-pipe-nozzle area on the performance characteristics of the six-stage and ten-stage axial-flow compressors of the 19B-8 and 19XB-1 engines, respectively, The data were obtained over a range of simulated altitudes and flight Mach numbers. At each simulated flight condition the engine was run over its full operable range of speeds. Performance characteristics of the 19B-8 and 19XB-1 compressors for the range of operation obtainable in the turboJet-engine installation are presented. Compressor characteristics are presented as functions of air flow corrected to sea-level conditions, compressor Mach number, and compressor load coefficient. For the range of compressor operation investigated, changes in Reynolds number had no measurable effect on the relations among compressor Mach number, corrected air flow, compressor load coefficient, compressor pressure ratio, and compressor efficiency. The operating lines for the 19B-8 compressor lay on the low-air-flow side of the region of maximum compressor efficiency; the 19B-8 compressor operated at higher average pressure coefficients per stage and produced a lower over-all pressure ratio than did the 19XB-1 compressor.

Dietz, Robert O.↗
NASA NTRS2019

NASA Marshall Space Flight Center Human Factors Engineering Analysis of Various Hatch Sizes and Associated Safety Impacts

The NASA Docking System (NDS) is a 31.5-inch (800-millimeter)-diameter circular hatch for astronauts to pass through when docked to other pressurized elements in space or for surface egress. The NDS is utilized on the Orion Spacecraft and has been implemented as the International Docking System Standard (IDSS). The EV74 Human Factors Engineering (HFE) Team at NASA’s Marshall Space Flight Center (MSFC) conducted human factors analyses with various hatch shapes and sizes to accommodate for all astronaut anthropometries, task comfort, and task safety. The 32-inch hatch is too small and a bigger hatch size would better accommodate most astronauts and prove to be safer for daily pass-throughs. To conduct human factors analyses, four participants were gathered based on anthropometry: 1st female, 5th female, 95th male, and 99th male.

Andrews, Tanya C.↗
NASA NTRS2019

NASA Marshall Space Flight Center Human Factors Engineering Analysis of Various Hatch Sizes

The NASA Docking System (NDS) is a 31.4961-inch (800 mm) diameter circular hatch for astronauts to pass through when docked to other pressurized elements in space or for entrance or egress on surface environments. The NDS is utilized on the Orion Spacecraft and has been implemented as the International Docking System Standard (IDSS). The EV74 Human Factors Engineering (HFE) Team at NASA’s Marshall Space Flight Center (MSFC) conducted human factors analyses with various hatch shapes and sizes to accommodate for all astronaut anthropometries and daily task comfort. It is believed that the hatch, approximately 32 inches, is too small, and a bigger hatch size would better accommodate most astronauts. In order to conduct human factors analyses, four participants were gathered based on anthropometry percentiles: 1st female, 5th female, 95th male, and 99th male.

Andrews, Tanya↗
NASA NTRS1984

Engineering analysis of drooped leading-edge wings near stall

Numerical results obtained with a three-dimensional vortex panel computer program for the calculation of inviscid, incompressible (potential) flow over infinitely thin finite wings with camber are presented. The program, which is designed for wings with drooped leading edge discontinuities, is essentially a numerical representation of lifting surface theory, involving both spanwise and chordwise distributions of vorticity. The results also include two engineering approximations. First, the effect of the leading-edge discontinuities is modeled by assuming that the vortices emanating from the discontinuities aerodynamically divide the wing into three distinct sections of lower aspect ratio. Secondly, the effect of the separated flow at high angle of attack is modeled by applying rectangular vortex panels with a varying vortex strength over the portions of the wing with attached flow.

Anderson, J. D., Jr.↗
NASA NTRS2010

Human Factors Vehicle Displacement Analysis: Engineering In Motion

While positioned on the launch pad at the Kennedy Space Center, tall stacked launch vehicles are exposed to the natural environment. Varying directional winds and vortex shedding causes the vehicle to sway in an oscillating motion. The Human Factors team recognizes that vehicle sway may hinder ground crew operation, impact the ground system designs, and ultimately affect launch availability . The objective of this study is to physically simulate predicted oscillation envelopes identified by analysis. and conduct a Human Factors Analysis to assess the ability to carry out essential Upper Stage (US) ground operator tasks based on predicted vehicle motion.

Atencio, Laura Ashley↗
DOE OSTI2022

A Systems Engineering Analysis of National Ignition Facility Industrial Controls Systems and Safety Interlock Systems Remote Input/Output Networking Migration from ControlNet to EtherNet/IP

The ControlNet industrial communications protocol and modules used in the Industrial Control System (ICS) and Safety Interlock System (SIS) at the National Ignition Facility (NIF) are no longer necessary and the ICS and SIS would be better served by migrating the communications structure to use EtherNet/Industrial Protocol (IP) and EtherNet bridge modules instead. By the admission of the vendor of ControlNet hardware, Rockwell Automation, in literature by Bill Petro [1], “Moving forward, customers will be able to optimize their asset utilization better using EtherNet/IP protocol than with ControlNet.” The NIF is one of the key elements of the Inertial Confinement Fusion (ICF) program at Lawrence Livermore National Laboratory (LLNL), a federally funded research and development center (FFRDC). The NIF contains the systems and provides the operational capacity to perform ICF, high energy density (HED), and discovery science experiments utilizing 192 individual beamlines, a host of diagnostics, and all the industrial systems required to facilitate these beamlines and diagnostics. The industrial systems are governed by the ICS and SIS, with the ICS providing control and the SIS providing monitoring and permissives. Construction on the NIF began in 1997 and was certified complete in 2009 and, as a result, the ICS and SIS were developed during this time using the tools that were available then. This includes the communications structure and protocols for these systems, much of which was, and still is, ControlNet. ControlNet, particularly during the time that the ICS and SIS were being built, has several attractive features. ControlNet hardware is exclusive to Rockwell Automation, which was the automation hardware chosen for the ICS and SIS. One feature that could be considered an advantage or a disadvantage depending on the communication needs of the system is that ControlNet also utilizes no active network components, excluding repeaters which are not always necessary. According to the architect of the ICS system at the NIF, Gordon Lau, one of the most attractive features of the ControlNet protocol during development of the ICS and SIS was that it is deterministic, providing timing of data transfer that is executed exactly as it is defined by the developer.

42 ENGINEERING↗
NASA NTRS1972

Preliminary design of an auxiliary power unit for the space shuttle. Volume 3: Details of system analysis, engineering, and design for selected system

Numerous candidate APU concepts, each meeting the space shuttle APU problem statement are considered. Evaluation of these concepts indicates that the optimum concept is a hydrogen-oxygen APU incorporating a recuperator to utilize the exhaust energy and using the cycle hydrogen flow as a means of cooling the component heat loads.

Hamilton, M. L.↗
NASA NTRS1973

Engineering analysis of ERTS data for southeast Asian agriculture

The present program focuses on rice because of its importance world-wide as a food. Specifically, the focus is on rice fields in the Philippines. Two primary program objectives are: (1) to establish the feasibility of extracting from ERTS imagery the areas where rice is grown, and (2) to determine those measurements on the imagery which enable the assessment of crop condition. Achieving these objectives with procedures which can be cost-effective can lead the way toward yield prediction, irrigation system management, and similar functions which are known to be important needs in Southeast Asia.

Heydt, H. L.↗