Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Engine Out”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Parametric evaluation of ducted fuel injection in an optically accessible mixing-controlled compression-ignition engine with two- and four-duct assemblies

Ducted fuel injection (DFI) is a strategy to improve fuel/charge-gas mixing in direct-injection compression-ignition engines. DFI involves injecting fuel along the axis of a small tube in the combustion chamber, which promotes the formation of locally leaner mixtures in the autoignition zone relative to conventional diesel combustion. Previous work has demonstrated that DFI is effective at curtailing engine-out soot emissions across a wide range of operating conditions. This study extends previous investigations, presenting engine-out emissions and efficiency trends between ducted two-orifice and ducted four-orifice injector tip configurations. For each configuration, parameters investigated include injection pressure, injection duration, intake manifold pressure, intake manifold temperature, start of combustion timing, and intake-oxygen mole fraction. For both configurations and across all parameters, DFI reduced engine-out soot emissions compared to conventional diesel combustion, with little effect on other emissions and engine efficiency. Emissions trends for both configurations were qualitatively the same across the parameters investigated. The four-duct configuration had higher thermal efficiency and indicated-specific engine-out nitrogen oxide emissions but lower indicated-specific engine-out hydrocarbon and carbon monoxide emissions than the two-duct assembly. Both configurations achieved indicated-specific engine-out emissions for both soot and nitrogen oxides that comply with current on- and off-road heavy-duty regulations in the United States without exhaust-gas aftertreatment at an intake-oxygen mole fraction of 12%. High-speed in-cylinder imaging of natural soot luminosity shows that some conditions include a second soot-production phase late in the cycle. The probability of these late-cycle events is sensitive to both the number of ducted sprays and the operating conditions.

Yraguen, Boni Frances↗
DOE OSTI2017

Hyperaccreting Black Hole as Gamma-Ray Burst Central Engine. II. Temporal Evolution of the Central Engine Parameters during the Prompt and Afterglow Phases

A hyperaccreting stellar-mass black hole (BH) has been proposed as the candidate central engine of gamma-ray bursts (GRBs). The rich observations of GRBs by Fermi and Swift make it possible to constrain the central engine model by comparing the model predictions against data. This paper is dedicated to studying the temporal evolution of the central engine parameters for both the prompt emission and afterglow phases. We consider two jet-launching mechanisms, i.e., ν ν-bar annihilations and the Blandford–Znajek (BZ) process, and obtain analytical solutions to these two models. We then investigate the BH central engine parameters, such as the jet power, the dimensionless entropy η, and the central engine parameter μ {sub 0} = η (1 + σ {sub 0}) (where σ {sub 0} is the initial magnetization of the engine) at the base of the jet. The BH may be spun up by accretion or spun down by the BZ process, leaving imprints in the GRB light curves. Usually, a BZ jet is more powerful and is likely responsible for the late-time central engine activities. However, an initially non-spinning BH central engine may first launch a thermal “fireball” via neutrino annihilations, and then launch a Poynting-flux-dominated jet via the BZ process. Multiple flares, giant bumps, and plateaus in GRB afterglows can be produced as the result of late-time accretion onto the BH.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2016

Influence of Injector Location on Part-Load Performance Characteristics of Natural Gas Direct-Injection in a Spark Ignition Engine

Interest in natural gas as an alternative fuel source to petroleum fuels for light-duty vehicle applications has increased due to its domestic availability and stable price compared to gasoline. With its higher hydrogen-to-carbon ratio, natural gas has the potential to reduce engine out carbon dioxide emissions, which has shown to be a strong greenhouse gas contributor. For part-load conditions, the lower flame speeds of natural gas can lead to an increased duration in the inflammation process with traditional port-injection. Direct-injection of natural gas can increase in-cylinder turbulence and has the potential to reduce problems typically associated with port-injection of natural gas, such as lower flame speeds and poor dilution tolerance. A study was designed and executed to investigate the effects of direct-injection of natural gas at part-load conditions. Steady-state tests were performed on a single-cylinder research engine representative of current gasoline direct-injection engines. Tests were performed with direct-injection in the central and side location. The start of injection was varied under stoichiometric conditions in order to study the effects on the mixture formation process. In addition, exhaust gas recirculation was introduced at select conditions in order to investigate the dilution tolerance. Relevant combustion metrics were then analyzed for each scenario. Experimental results suggest that regardless of the injector location, varying the start of injection has a strong impact on the mixture formation process. Delaying the start of injection from 300 to 120°CA BTDC can reduce the early flame development process by nearly 15°CA. While injecting into the cylinder after the intake valves have closed has shown to produce the fastest combustion process, this does not necessarily lead to the highest efficiency, due to increases in pumping and wall heat losses. When comparing the two injection configurations, the side location shows the best performance in terms of combustion metrics and efficiencies. For both systems, part-load dilution tolerance is affected by the injection timing, due to the induced turbulence from the gaseous injection event. CFD simulation results have shown that there is a fundamental difference in how the two injection locations affect the mixture formation process. Delayed injection timing increases the turbulence level in the cylinder at the time of the spark, but reduces the available time for proper mixing. Side injection delivers a gaseous jet that interacts more effectively with the intake induced flow field, and this improves the engine performance in terms of efficiency.

Sevik, James↗
DOE OSTI2013

Rotating Liner Engine: Improving Efficiency of Heavy Duty Diesels by Significant Friction Reduction, and Extending the Life of Heavy Duty Engines.

This report describes the work on converting a 4 cylinder Cummins ISB engine into a single cylinder Rotating Liner Engine functioning prototype that can be used to measure the friction benefits of rotating the cylinder liner in a high pressure compression ignition engine. A similar baseline engine was also prepared, and preliminary testing was done. Even though the fabrication of the single cylinder prototype was behind schedule due to machine shop delays, the fundamental soundness of the design elements are proven, and the engine has successfully functioned. However, the testing approach of the two engines, as envisioned by the original proposal, proved impossible due to torsional vibration resonance caused by the single active piston. A new approach for proper testing has been proposed,

Rotating Liner Engine, Engine Friction, Friction R↗
DOE OSTI2017

Steady-State Calibration of a Diesel Engine in CFD Using a GPU-Based Chemistry Solver

The prospect of analysis-driven pre-calibration of a modern diesel engine is extremely valuable in order to significantly reduce hardware investments and accelerate engine designs compliant with stricter EPA fuel economy regulations. Advanced modeling tools, such as CFD, are often used with the goal of streamlining significant portions of the calibration process. The success of the methodology largely relies on the accuracy of analytical predictions, especially engine-out emissions. However, the effectiveness of CFD simulation tools for in-cylinder engine combustion is often compromised by the complexity, accuracy, and computational overhead of detailed chemical kinetics necessary for combustion calculations. The standard approach has been to use skeletal kinetic mechanisms (~50 species) which consume acceptable computational time but with degraded accuracy.In this work, a comprehensive demonstration and validation of the analytical pre-calibration process is presented for a passenger car diesel engine using CFD simulations with CONVERGE™ and a GPU-based chemical kinetics solver (Zero-RK, developed at Lawrence Livermore National Laboratory) on high performance computing resources to enable the use of detailed kinetic mechanisms. Diesel engine combustion computations have been conducted over 600 operating points spanning in-vehicle speed-load map, using massively parallel ensemble simulation sets on the Titan supercomputer located at the Oak Ridge Leadership Computing Facility. The results with different mesh resolutions have been analyzed to compare differences in combustion and emissions (NO x , Carbon Monoxide CO, Unburned Hydrocarbons UHC, and Smoke) with actual engine measurements. The results show improved agreement in combustion and NO x predictions with a large n-heptane mechanism consisting of 144 species and 900 reactions with refined mesh resolution; however; agreement in CO, UHC and Smoke remain a challenge.

Gao, Jian↗
DOE OSTI2013

Protein engineering for metabolic engineering: Current and next-generation tools

Protein engineering in the context of metabolic engineering is increasingly important to the field of industrial biotechnology. As the demand for biologically produced food, fuels, chemicals, food additives, and pharmaceuticals continues to grow, the ability to design and modify proteins to accomplish new functions will be required to meet the high productivity demands for the metabolism of engineered organisms. We review advances in selecting, modeling, and engineering proteins to improve or alter their activity. Some of the methods have only recently been developed for general use and are just beginning to find greater application in the metabolic engineering community. We also discuss methods of generating random and targeted diversity in proteins to generate mutant libraries for analysis. Recent uses of these techniques to alter cofactor use; produce non-natural amino acids, alcohols, and carboxylic acids; and alter organism phenotypes are presented and discussed as examples of the successful engineering of proteins for metabolic engineering purposes.

Marcheschi, RJ↗
DOE OSTI2016

The engine reformer: Syngas production in an engine for compact gas‐to‐liquids synthesis

Methane (CH 4 ) reforming was carried out in an internal combustion engine (an “engine reformer”). We successfully produced syngas from the partial oxidation of natural gas in the cylinder of a diesel engine that was reconfigured to perform spark ignition. Performing the reaction in an engine cylinder allows some of the exothermicity to be captured as useful work. Intake conditions of 110 kPa and up to 480 °C allowed low cycle‐to‐cycle variability ( COV nimep < 20 %) at methane‐air equivalence ratios ( ϕ M ) of 2.0, producing syngas with an H 2 ‐to‐CO ratio of 1.4. Spark ignition timing was varied between 45–30° before top‐dead‐center (BTDC) piston position, showing significant improvement with delayed timing. Hydrogen (H 2 ) and ethane (C 2 H 6 ) were added to simulate recycle from a downstream synthesis reactor and realistic natural gas compositions, respectively. Adding these gases yielded a stable combustion up to hydrocarbon‐air equivalence ratios ( ϕ HC ) of 2.8 with COV nimep < 5 %. Ethane concentrations (with respect to methane) of up to 0.2 L/L (20 vol%) (with and without H 2 ) produced robust and stable combustions, demonstrating that the engine can be operated across a range of natural gas compositions. Engine exhaust soot concentrations demonstrated elevated values at ϕ HC > 2.4, but < 1 mg/L below these equivalence ratios. These results demonstrate that the engine reformer could be a key component of a compact gas‐to‐liquids synthesis plant by highlighting the operating conditions under which high gas conversion, high H 2‐ to‐CO ratios close to 2.0, and low soot production are possible.

Lim, Emmanuel G.↗
DOE OSTI2021

Fuel Property Effects on Knock Propensity and Thermal Efficiency in a Direct-Injection Spark-Ignition Engine

Engine knock remains one of the major barriers to further improvement in thermal efficiency of Direct-Injection Spark-Ignition (DISI) engines. While Research Octane Number and Motor Octane Number are often used as standard rating methods for knock resistance of fuels, the impacts of other fuel properties on knock propensity in modern engines such as heat of vaporization (HoV) and laminar flame speed (LFS) require better understanding in order to co-optimize fuels and engine designs to achieve higher thermal efficiency and lower CO2 emission. In the present study, computational fluid dynamics (CFD) is used to model a boosted DISI engine with a focus on knock prediction and fuel property effects. A level-set G-equation model is employed to capture turbulent premixed combustion, and is coupled with a transported Livengood-Wu (L-W) integral approach to predict autoignition in the unburnt region. A criterion associated with the L-W integral is developed to accurately predict knock onset and knock-limited spark-advance. This model is then applied to a sensitivity analysis of HoV and LFS on knock tendency and thermal efficiency. The pressure-temperature trajectory framework is applied and extended to study the fuel effects on auto-ignition process in the engine. An existing efficiency-based merit function, which is derived from experiments for boosted SI engines, is evaluated and improved based on the current CFD results.

DISI↗
DOE OSTI2018

Relationship of compressive stress-strain response of engineering materials obtained at constant engineering and true strain rates

In this paper, a Johnson–Cook model was used as an example to analyze the relationship of compressive stress-strain response of engineering materials experimentally obtained at constant engineering and true strain rates. There was a minimal deviation between the stress-strain curves obtained at the same constant engineering and true strain rates. The stress-strain curves obtained at either constant engineering or true strain rates could be converted from one to the other, which both represented the intrinsic material response. There is no need to specify the testing requirement of constant engineering or true strain rates for material property characterization, provided that either constant engineering or constant true strain rate is attained during the experiment.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Impact of fuel and engine operating conditions on efficiency of a heavy duty truck engine running compression ignition mode using energy and exergy analysis

Gasoline compression ignition using a single gasoline-type fuel for direct/port injection has been shown as a method to achieve low temperature combustion with low engine-out NO x and soot emissions and high indicated thermal efficiency. However, key technical barriers to achieving low temperature combustion on multi-cylinder engines include the air handling system (limited amount of exhaust gas recirculation) as well as mechanical engine limitations (e.g. peak pressure rise rate). In light of these limitations, high temperature combustion with reduced amounts of exhaust gas recirculation appears more practical. Previous studies by the authors demonstrated that utilizing port and direct injection of E85 gasoline simultaneously resulted in the best performance and the highest brake thermal efficiency of 47.1%, which was 1.2% higher compared to diesel baseline. For further efficiency improvement, a better understanding of energy and exergy loss mechanisms is required. As such, in this work first and second law thermodynamics analysis were applied to experiments with gasoline compression ignition at an engine speed of 1038 rpm and brake mean effective pressure of 1.4 MPa on a 12.4 L multi-cylinder heavy-duty diesel engine. The impact on the efficiency, losses, and irreversibility with respect to various parameters such as fuel, injection strategy, intake condition, and port injected water mass was quantified. The peak efficiency of ideal cycles and the combined efficiency with a waste heat recovery system were also estimated in this study to assess opportunities for further efficiency gains. It was found that the combustion irreversibility was dominated by the combustion temperature rather than the fuel structure. Despite its highest brake thermal efficiency, E85 gasoline generated the highest exergy destruction due to its lowest combustion temperature. For the same reason, retarding the combustion phasing or adopting a port and direct injection strategy increased the exergy destruction. The combustion duration loss was more notable than the phasing loss and was affected by both the combustion duration and shape of heat release profile. Water port injection increased the exhaust energy, but the available energy dropped significantly attributed to the decrease in the exhaust temperature, rendering waste heat recovery ineffective. The second law analysis serves as a helpful tool in conjunction with the first law analysis to explore pathways to maximize engine efficiency.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2015

Tribological bench and engine dynamometer tests of a low viscosity SAE 0W-16 engine oil using a combination of ionic liquid and ZDDP as anti-wear additives

We have previously reported an oil-miscible phosphonium-organophosphate ionic liquid (IL) with an effective anti-wear (AW) functionality when added to a base oil by itself or combined with a conventional zinc dialkyldithiophosphate (ZDDP) for a synergistic effect. In this research, we investigated whether this synergy manifests in formulated engine oils. An experimental SAE 0W-16 engine oil was generated containing a combination of IL and ZDDP with equal phosphorus contribution. The prototype engine oil was first evaluated using tribological bench tests: AW performance in boundary lubrication (BL) and friction behavior (Stribeck curves) in elastohydrodynamic, mixed, and BL. In addition, the forthcoming standard Sequence VIE engine dynamometer test was then conducted to demonstrate improved fuel economy. Results were benchmarked against those of another experimental engine oil with almost the same formulation except using ZDDP only without the IL (similar total phosphorus content). The IL-ZDDP formulation consistently outperforms the ZDDP-only formulation in friction reduction and wear protection, and results from the bench and engine tests are well correlated.

42 ENGINEERING↗
DOE OSTI2013

Climate Engineering with Stratospheric Aerosols and Associated Engineering Parameters

Climate engineering with stratospheric aerosols, an idea inspired by large volcaniceruptions, could cool the Earth’s surface and thus alleviate some of the predicted dangerous impacts of anthropogenic climate change. However, the effectiveness of climate engineering to achieve a particular climate goal, and any associated side effects, depend on certain aerosol parameters and how the aerosols are deployed in the stratosphere. Through the examples of sulfate and black carbon aerosols, this paper examines "engineering" parameters-aerosol composition, aerosol size, and spatial and temporal variations in deployment-for stratospheric climate engineering. The effects of climate engineering are sensitive to these parameters, suggesting that a particle could be found ordesigned to achieve specific desired climate outcomes. This prospect opens the possibility for discussion of societal goals for climate engineering.

aerosols↗
DOE OSTI2014

Review on characterization of nano-particle emissions and PM morphology from internal combustion engines: Part 2 [Review on morphology and nanostructure characterization of nano-particle emission from internal combustion engines]

This study presents a review of the characterization of physical properties, morphology, and nanostructure of particulate emissions from internal combustion engines. Because of their convenience and readiness of measurement, various on-line commercial instruments have been used to measure the mass, number, and size distribution of nano-particles from different engines. However, these on-line commercial instruments have inherent limitations in detailed analysis of chemical and physical properties, morphology, and nanostructure of engine soot agglomerates, information that is necessary to understand the soot formation process in engine combustion, soot particle behavior in after-treatment systems, and health impacts of the nano-particles. For these reasons, several measurement techniques used in the carbon research field, i.e., highresolution transmission electron microscopy (HRTEM), X-ray diffraction (XRD), and Raman spectroscopy, were used for analysis of engine particulate matter (PM). This review covers a brief introduction of several measurement techniques and previous results from engine nano-particle characterization studies using those techniques.

47 OTHER INSTRUMENTATION↗