Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Electric Machine”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Dual Phase Soft Magnetic Laminates for Low-cost, Non/Reduced-Rare-Earth Containing Electrical Machines

To accelerate the mass market adoption of electric drive vehicles, the key technology barriers in electric motors are (1) magnet cost and rare-earth element price volatility; (2) non-rare-earth electric motor performance; and (3) materials property optimization. The goal of this project was to address these barriers by advancing a unique and innovative dual phase soft magnetic material technology and demonstrating the material in a 30-kW synchronous reluctance motor without using any permanent magnet for electric vehicles. Dual phase magnetic materials offer the electric motor designer the ability to locally control the magnetic saturation level in a motor laminate, while at the same time enhancing the mechanical strength of the laminate material, resulting in an enhancement in motor performance and efficiency. Scalable dual phase soft magnetic laminates manufacturing technologies were developed in collaboration with multiple US manufacturers. 1000 lbs of alloy sheet with a thickness of 0.25mm and width of 280 mm was manufactured within the specifications. Batch sizes of up to 240 laminates per run were produced from the alloy sheet. Two prototype motors with dual phase soft magnetic laminates were designed, built, and tested. The major goal of building the subscale prototype as a pathway to develop scalable manufacturing technologies for the dual phase soft magnetic laminates was met. The additional goal of building and testing the subscale prototype in order to validate the calculated performance with the tested motor performance was also met. For the full-scale 30kW continuous power synchronous reluctance motor prototype, the tested performance met the targets in terms of continuous power at the operating speeds up to 8000 rpm. Post-test studies were conducted and the root causes for the discrepancy between the predicted and tested peak power, continuous power at high speed range, and efficiency were identified. Further modeling study showed that the dual phase rotor machine has a 27% higher torque to active weight ratio than an equivalent performance silicon steel rotor machine. Application space and multiple discussions with traction motor and electric vehicle manufacturers for commercialization of the dual phase soft magnetic material technology were identified and conducted. An initial cost model was established based on the developed manufacturing technologies with the US manufacturers. Future paths for further cost reduction were identified, including increasing the market volume by broadening the applications of the dual phase soft magnetic laminate technology for electric machines in other energy sections such as oil & gas, heating, ventilation, and air conditioning (HVAC), and power generation.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2020

MADE3D™ (Manufacturing and Additive Design of Electric Machines Enabled by Three-Dimensional Printing) [SWR-20-70]

The MADE3D™ software uses advanced neural networks for realizing novel high torque density electric machine designs with desired functional specifications not limited to but including torque, magnetic loading, and mass. This software allows for a reduction in cost of design by using next-generation computational resources including the cloud while still maintaining high accuracy. The design of the neural networks allows for exploration of large design space and possibilities to find more optimal designs and accommodate new manufacturing technologies like 3D printing.

Sethuraman, Latha↗
DOE OSTI2025

Electromagnetic Modeling of Lattice Structures in Additively Manufactured Electric Machines

Recent advancements in metal additive manufacturing (AM) show great potential to revolutionize the design and manufacturing of electromagnetic components used in the field of electrical engineering. Lattice structures directly printed by AM processes typically offer better structural performance with reduced weight, such as high stiffness, surface area, elongation, energy absorption, and porosity, than the solid counterpart. This paper aims to study the electromagnetic modeling of lattice structures used in additively manufactured magnetic cores or windings for electric machines. Three dimensional (3D) electromagnetic finite element (FE) analysis with high performance computing (HPC) shows the highest fidelity in predicting the electromagnetic performance of designs with lattice structures by preserving complex geometry details. FE-based homogenization methods have also been explored to potentially speed up concept design. A case study based on an additively manufactured axial-flux permanent magnet machine with a Hilbert pattern stator validates the discussed electromagnetic modeling approaches.

Chung, Shi-Uk [ANSYS, Inc.]↗
NASA NTRS1976

Sample preparation of metal alloys by electric discharge machining

Electric discharge machining was investigated as a noncontaminating method of comminuting alloys for subsequent chemical analysis. Particulate dispersions in water were produced from bulk alloys at a rate of about 5 mg/min by using a commercially available machining instrument. The utility of this approach was demonstrated by results obtained when acidified dispersions were substituted for true acid solutions in an established spectrochemical method. The analysis results were not significantly different for the two sample forms. Particle size measurements and preliminary results from other spectrochemical methods which require direct aspiration of liquid into flame or plasma sources are reported.

Chapman, G. B., II↗
NASA NTRS1983

Six-Axis Electrical-Discharge Machine

Electrical discharge machine (EDM) of unusual versitility made by conversion of radial drill. Drilling head is replaced by ram that holds and positions electrode. Tank and recirculation system for coolant are added. EDM has six independent motions and drastically reduced cost of manufacturing. New applications are constantly being found.

Werner, A. R.↗
DOE OSTI2020

Automotive Power Electronics and Electric Machine Thermal Management

The transition to modular and scalable electrified vehicle transportation requires technologies to improve power density within cost and reliability constraints to maximize vehicle platform flexibility. Key research challenges arise due to the limited packaging space, coolant distribution, electrical connections, and ambient temperatures. Challenges include thermal management for compact power-dense electric machines and the associated power electronics for power management within the vehicle. High-temperature silicon and wide-bandgap (WBG) based power electronics systems are of interest to enable compact and efficient electric drive systems. The higher temperatures present packaging challenges for thermal management and reliability. In this work, we provide an overview of research for thermal characteristics of materials, packages and thermal management approaches for enabling compact power dense automotive electric drive systems.

DIRECT ENERGY CONVERSION↗
DOE OSTI2024

Improving Efficiency of Off-Road Vehicles by Novel Integration of Electric Machines and Advanced Combustion Engines

Modern off-road equipment will increasingly rely on electrified implements that will deliver precision control with a smaller footprint than hydraulics. The primary energy converter, however, will be an onboard reciprocating internal combustion engine because of the power density of hydrocarbon fuels in comparison to electrical energy storage and the remote locations where much of this equipment is deployed. Adding energy storage and electric machines creates opportunities to improve efficiency while reducing emissions. This program investigated approaches to take advantage of the extra flexibility that an enhanced electrical system to enable high-efficiency, low-emissions combustion technologies. The current program evaluated hybridization of both the torque application and air-handling systems to maximize efficiency while minimizing cost. This program designed, analyzed and tested a hybrid off-road vehicle consisting of a series electric powertrain with energy storage, an electrified air system, and a 33% downsized diesel engine. Detailed comparisons were made between the base powertrain and the developed powertrain using powertrain simulations, engine testing, and vehicle testing. The key results of the study are: • The resulting vehicle reduces fuel consumption by 5% to 15% at equal productivity. The primary improvements were due to recovery of regenerative braking losses for cycles where large transients are encountered. • The electrified air system was an enabler to allow engine downsizing. This was most important for duty-cycles where the engine primarily operated at moderate loads and had few low speed high torque conditions. • Engine level improvements showed re-optimization of the powertrain is possible when electrified air handing is available. Increased exhaust gas recirculation and advanced injection timing allowed up to a 15% reduction in brake specific fuel consumption at equal NOx and transient response. Compared to the larger engine, the downsized engine achieves up to an 18% reduction in brake specific fuel consumption over the non-road transient cycle. • The life cycle analysis and total cost of ownership study showed that the hybrid powertrain has the potential to reduce 5-year CO2 and total cost of ownership by ~6% over the baseline vehicle. The results also indicated that a pure battery electric vehicle is not feasible in this application and is likely to increase the CO2 emissions due to the CO2 from battery production. A hybrid powertrain with low carbon fuels shows the potential to substantially reduce CO2 and total cost of ownership.

02 PETROLEUM↗
NASA NTRSDate not supplied

Thermally Conductive Insulation for High Power Density Electric Machines

In the mid 2000’s NASA challenged the aeronautics industry to identify the routes for achieving ambitious improvements in fuel burn, emission, and noise reductions. These so-called “N+3” studies were exploring broad changes three commercial aircraft generations, or nominally 30 years, in the future. Many intriguing propulsion-airframe integrated solutions were proposed and pursued, which incorporated technologies such as high-aspect-ratio wings, boundary-layer ingestion, and hybrid electric powertrains. This talk summarizes the approaches and achievements from the Hybrid Gas-Electric Propulsion Concept Technical Challenge that concluded in 2019. The balanced portfolio of concepts studies anchored with practical technology development demonstrated that electrified aircraft propulsion is an aircraft revolution whose time has come. Advanced materials will play a key role with enabling the increase in operating efficiencies and lifetime of these high power-dense electric machines. Progress made in materials development as part of NASA’s Advanced Air Transport Technology project will also be discussed.

electrical insulation↗
NASA NTRS2015

Key Performance Parameter Driven Technology Goals for Electric Machines and Power Systems

Transitioning aviation to low carbon propulsion is one of the crucial strategic research thrust and is a driver in the search for alternative propulsion system for advanced aircraft configurations. This work requires multidisciplinary skills coming from multiple entities. The feasibility of scaling up various electric drive system technologies to meet the requirements of a large commercial transport is discussed in terms of key parameters. Functional requirements are identified that impact the power system design. A breakeven analysis is presented to find the minimum allowable electric drive specific power and efficiency that can preserve the range, initial weight, operating empty weight, and payload weight of the base aircraft.

Electric Machines↗
DOE OSTI2022

Electric machines as motors and power generators

Devices, methods, and systems for electrostatic machines which can act as both an electric motor, converting electrical energy to mechanical energy, and an electric generator, converting mechanical energy to electrical energy, are described. In some embodiments, a spring positioned between two oppositely charged plates may be used as an electric motor and/or electric generator.

Datskos, Panagiotis G.↗
NASA NTRSDate not supplied

Cryogenic Vacuum Chamber Testing of A Conductively-Cooled, High Temperature Superconducting Rotor for a 1.4 MW Electric Machine for Aeronautics Applications

This paper presents the first ever demonstration of a superconducting rotor cooled conductively without a cryogenic fluid or solid. The full-scale rotor was operated statically in its intended environment – about 1e-3 torr vacuum with only conductive cooling through mechanical connections to a cryocooler contained on the rotor. Stable operation of the rotor in a representative magnetic environment was demonstrated up to its rated direct current (57.2 A) and the designed temperature limit for the superconductor (62 K). Additional electrical measurements increased confidence that the superconducting coils functioned as intended. A collection of steady state temperature distributions was measured at operating and non-operating conditions. In all but one case, the observed temperature gradient between the cold tip and superconducting coils satisfies the design but with little margin. Opportunities to reduce the gradient are identified.

Electrified aircraft propulsion↗
NASA NTRSDate not supplied

Cryogenic Vacuum Chamber Testing of A Conductively-Cooled, High Temperature Superconducting Rotor for a 1.4 MW Electric Machine for Aeronautics Applications

This paper presents the second ever demonstration of a superconducting rotor cooled only via conductive connection to a cryocooler, i.e., without pumped or solid cryogens. The fullscale rotor was operated statically in its intended environment – about 1e-3 torr vacuum with only conductive cooling through mechanical connections to a cryocooler contained on the rotor. Stable operation of the rotor in a representative magnetic environment was demonstrated up to its rated direct current (57.2 A) and the designed temperature limit for the superconductor (62 K). Additional electrical measurements increased confidence that the superconducting coils functioned as intended. A collection of steady state temperature distributions was measured at operating and non-operating conditions. In all but one case, the observed temperature gradient between the cold tip and superconducting coils satisfies the design but with little margin. Opportunities to reduce the gradient are identified.

Electrified aircraft propulsion↗
DOE OSTI2021

Silicon carbide power inverter/rectifier for electric machines

The present disclosure involves a two stage inverter, a system for electrical power conversation, and a method of converting electrical power using silicon carbide (SiC) metal-oxide-semiconductor field-effect transistors (MOSFETs). One example implementation includes using two or more SiC MOSFETs in series with each MOSFET having a gate terminal for triggering a state switch between an on (conducting) and off (non-conducting) state of the MOSFET. An AC terminal is connected between the series SiC MOSFETS, and the series SiC MOSFETs are connected across a DC bus and in parallel with one or more capacitors.

Shenoy, Suratkal P.↗