Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “EVM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

Demonstration of GaN HEMT MMIC High-Power Amplifier for Lunar Proximity Communications

In this paper, we demonstrate a high efficiency, Ka-band (23.15 to 23.55 GHz) GaN HEMT MMIC based single-ended high power amplifier (HPA). The measured Pout, Gain, PAE, RMS EVM for Offset-QPSK, 8PSK, 16APSK, and 32APSK waveforms, 3rd-order IMD products, noise figure, and phase noise are presented. The results indicate that the saturated output power (P sat ) and the small signal Gain are on the order of 38.8 dBm (7.6 W) and 29.3 dB, respectively. The PAE at Psat is 20.0%. At the 1-dB compression point, the RMS EVM and the out-of-band spectral regrowth are less than 6% and –26 dBc respectively, for all four waveforms. Additionally, the spectrum is in compliance with the NTIA mask requirements for all four waveforms. The output 3rd-order intercept point (OIP3) is on the order of 42 dBm. The noise figure is less than 9.5 dB. The SSB phase noise spectral density is compliant with the envelope defined by the MIL-STD-188-164C. The HPA can enable proximity forward links between the orbiting Gateway/relay satellites and the lunar surface elements and cross links between relay satellites.

Ka-band↗

Environmental Cleanup of the East Tennessee Technology Park Year One - Execution with Certainty SM - 13120

On August 1, 2011, URS - CH2M Oak Ridge LLC (UCOR) began its five-year, $1.4 billion cleanup of the East Tennessee Technology Park (ETTP), located on the U.S. Department of Energy's (DOE) Oak Ridge Reservation in Tennessee. UCOR will close out cleanup operations that began in 1998 under a previous contract. When the Contract Base scope of work [1] is completed in 2016, the K-25 gaseous diffusion building will have been demolished and all waste dispositioned, demolition will have started on the K-27 gaseous diffusion building, all contact-handled and remote-handled transuranic waste in inventory (approximately 500 cubic meters) will have been transferred to the Transuranic Waste Processing Center, previously designated 'No-Path-To-Disposition Waste' will have been dispositioned to the extent possible, and UCOR will have managed DOE Office of Environmental Management (EM)- owned facilities at ETTP, Oak Ridge National Laboratory (ORNL), and the Y-12 National Security Complex in a safe and cost-effective manner. Since assuming its responsibilities as the ETTP cleanup contractor, UCOR has completed its life-cycle Performance Measurement Baseline; received its Earned Value Management System (EVMS) certification; advanced the deactivation and demolition (D and D) of the K-25 gaseous diffusion building; recovered and completed the Tank W-1A and K-1070-B Burial Ground remediation projects; characterized, packaged, and shipped contact-handled transuranic waste to the Transuranic Waste Processing Center; disposed of more than 90,000 cubic yards of cleanup waste while managing the Environmental Management Waste Management Facility (EMWMF); and provided operations, surveillance, and maintenance activities at DOE EM facilities at ETTP, ORNL, and the Y-12 National Security Complex. Project performance as of December 31, 2012 has been excellent: - Cost Performance Index - 1.06; - Schedule Performance Index - 1.02. At the same time, since safety is the foundation of all cleanup work, UCOR's safety record goes hand in hand with its excellent project performance. Through calendar year 2012, UCOR's recordable injury rate was 0.33, and the company has worked close to 4 million hours without a lost work day injury. UCOR's safety record is one of the best in the DOE EM Complex. This performance was due, in large part, to the people and processes URS and CH2M HILL, the parent companies of UCOR, brought to the project. Key approaches included: - Selected and deployed experienced staff in key leadership positions throughout the organization; - Approached 'Transition' as the 'true' beginning of the cleanup project - kicking off a number of project initiatives such as Partnering, PMB development, D and D Plan execution, etc. - Established a project baseline for performance measurement and obtained EVMS certification in record time; - Determined material differences and changed conditions that warranted contract change - then quickly addressed these changes with the DOE client; - Aligned the project and the contract within one year - also done in record time; - Implemented Safety Trained Supervisor and Safety Conscious Work Environment Programs, and kicked off the pursuit of certification under DOE's Voluntary Protection Program. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Latest Developments in PM Systems and Methods and their Application to WM Projects - 20364

How do you improve on an industry that is well established yet often misses the mark on key metrics demonstrating effective planning and execution of project scope, schedule and budget? With the increased complexity of DOE projects relative to either poorly kept records of what wastes are stored or the lack of specific knowledge relative to the waste concentrations/quantities, this is a question continually asked and investigated by many. In fact, in 2017, the GAO's report to Congress indicated that although the DOE has made some progress on its monitoring effectiveness and demonstrating progress criteria, these goals were not met and there needs to be more improvement and monitoring. This paper will offer some insights into the latest developments in project management methodologies and the possible application of these to waste management projects. Traditional data generated via a project schedule that utilizes critical path methodology (CPM) and additional earned value management (EVM) data needs to be accurate and enable the project manager to better understand the probability of project success. Although this data has readily been available on most large-scale projects, success as measured by various stakeholder groups including the client, project team, regulators, etc. is less than optimal. Therefore, an urgent need exists to explore how traditional project data (CPM and EVM) coupled with new methodologies allows for better planning and execution by the project team. Many new approaches/methodologies can even be used to predict the success of options prior to full implementation on the actual project. Three approaches/methodologies will be discussed: - Artificial Intelligence; - Change Management; - Blend of Traditional Management (Gantt chart) and Agile Methodologies. As market forces change, so will the direction of project management. The days of 'one size fits all' are no longer valid. A combination of predictive and adaptive approaches in the management of projects is essential to enable execution of project deliverables on time, under budget, and within the contractual scope. This paper is intended to provide the reader with insight to the close relationship of project management trends and business management trends, and to provoke critical thinking about what it means to align project management strategy with an environment of non-stop innovation. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Method of Best Representation for Averages in Data Evaluation

A new method for averaging data for which incomplete information is available is presented. For example, this method would be applicable during data evaluation where only the final outcomes of the experiments and the associated uncertainties are known. This method is based on using the measurements to construct a mean probability density for the data set. This “expected value method” (EVM) is designed to treat asymmetric uncertainties and has distinct advantages over other methods of averaging, including giving a more realistic uncertainty, being robust to outliers and consistent under various representations of the same quantity.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Observation of Rashba zero-field spin splitting in a strained germanium 2D hole gas

We report the observation, through Shubnikov-de Haas oscillations in the magnetoresistance, of spin splitting caused by the Rashba spin-orbit interaction in a strained Ge quantum well epitaxially grown on a standard Si(001) substrate. The Shubnikov-de Haas oscillations display a beating pattern due to the spin split Landau levels. The spin-orbit parameter and Rashba spin-splitting energy are found to be 1.0 × 10{sup −28 } eVm{sup 3} and 1.4 meV, respectively. This energy is comparable to 2D electron gases in III-V semiconductors, but substantially larger than in Si, and illustrates the suitability of Ge for modulated hole spin transport devices.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Generalized Theory and Realization of Reconfigurable Bandpass Filtering Equalizers

Here, in this article, a generalized theory of bandpass filtering equalizers is proposed. A filtering equalizer is a device that combines the frequency-selective properties of a filter with the controllable slope of an equalizer into a single component. The equations used to design the function for a desired slope are provided, and the design methodology to determine the necessary filtering polynomials is also shown. The controllable slope of the dual-function component is realized using variable capacitors, which are used to tune both a transmission zero and a matching network to achieve the desired slope. A third-order bandpass filtering equalizer is designed, fabricated, and measured to verify the generalized theory. The component is designed to operate at 1 GHz with a slope that can be reconfigured from 1 to 3 dB along the passband. This proposed filtering equalizer demonstrates the feasibility of a tunable, low-cost, size, weight, and power (C-SWaP) solution to enable increased flatness in the overall system response and thereby decrease the error vector magnitude (EVM) of future radio frequency (RF) systems and a design process that allows for future development of filtering equalizers.

Filter↗

Learning an Eddy Viscosity Model Using Shrinkage and Bayesian Calibration: A Jet-in-Crossflow Case Study

In this paper, we demonstrate a statistical procedure for learning a high-order eddy viscosity model (EVM) from experimental data and using it to improve the predictive skill of a Reynolds-averaged Navier–Stokes (RANS) simulator. The method is tested in a three-dimensional (3D), transonic jet-in-crossflow (JIC) configuration. The process starts with a cubic eddy viscosity model (CEVM) developed for incompressible flows. It is fitted to limited experimental JIC data using shrinkage regression. The shrinkage process removes all the terms from the model, except an intercept, a linear term, and a quadratic one involving the square of the vorticity. The shrunk eddy viscosity model is implemented in an RANS simulator and calibrated, using vorticity measurements, to infer three parameters. The calibration is Bayesian and is solved using a Markov chain Monte Carlo (MCMC) method. A 3D probability density distribution for the inferred parameters is constructed, thus quantifying the uncertainty in the estimate. The phenomenal cost of using a 3D flow simulator inside an MCMC loop is mitigated by using surrogate models (“curve-fits”). A support vector machine classifier (SVMC) is used to impose our prior belief regarding parameter values, specifically to exclude nonphysical parameter combinations. The calibrated model is compared, in terms of its predictive skill, to simulations using uncalibrated linear and CEVMs. Finally, we find that the calibrated model, with one quadratic term, is more accurate than the uncalibrated simulator. The model is also checked at a flow condition at which the model was not calibrated.

42 ENGINEERING↗

302.2.03 Report on P43OL1139

This document describes the quality issues encountered in bare cable P43OL1139AA00A fabrication and the subsequent investigation performed at LBNL. The cable concerned was placed under L3 quarantine (braiding held, further QC required) in December 2020 upon fabrication due to mid-run facet size increase, and was elevated to L2 quarantine in February 2020 to require a more formal reporting and resolution. The approval (rejection) of this report by L2 on DocDB shall constitute acceptance (rejection) of the fabrication of the bare cable unit P43OL1139AA00A, upon which it may (may not) proceed to braiding and EVMS HO.

36 MATERIALS SCIENCE↗

ATS 6 EMI field measurements techniques and results

At the present time 'Applications Technology Satellite (ATS)-6' is the world's largest communication satellite. It handles telecommunications in the frequency range of 40 - 30,000 MHz. Power levels on board the spacecraft range from -110 dBm to 52.5 dBw. Consequently considerable care was required in the design and test of this spacecraft, in order to provide assurances that the spacecraft would perform properly in its own RF environments. The testing was performed first by placing the earth viewing module (EVM) in a specially constructed 'small' anechoic chamber with an overhead parabolic reflector section, of 8' in diameter, instead of the 30' reflector of the full scale design. The near field analysis of this paper proves that this test configuration leads to a desirable overtest for the spacecraft. The test requirements, procedure and results are also explained.

Afifi, M. S.↗

Hydrodynamics of primordial black hole formation

The hydrodynamic picture of the formation of primordial black holes (PBH) at the early stages of expansion of the Universe is considered. It is assumed that close to singularity, expansion occurs in a quasi-isotropic way. Using an EVM, a spherically symmetrical nonlinear problem of the evolution of primary strong deviation from the Fridman solution was solved. What these deviations must be, so that the formation of PBH occurred was clarified. Attention was devoted to the role of pressure gradients. It is pointed out that at the moment of formation of PBH, only a small part of matter enters into it, primarily the component of perturbation. It is also pointed out that at this moment, the mass of PBH essentially is smaller than the mass considered within the cosmic horizon. The possibility of changing the mass of the PBH as a result of accretion is analyzed.

Nadezhin, D. K.↗

Programming input-output operations in FORTRAN on magnetic tape

The subprogram MTCFF was designed for carrying out input-output operations in FORTRAN on magnetic tape within the framework of the DOS ES EVM operation system. It is possible, by means of this subprogram, to perform any input-output operations of interest to the programmer such as recording and reading various control operations in the direct and reverse directions, even though for these purposes the facilities of the language FORTRAN itself are limited. The subprogram can also be used in programs written in other programming languages.

Gorokov, V. N.↗

Earned Value - Added

Earned value management (EVM)... can be one of the most insightful methods of synthesizing cost, schedule, and technical status information into a single set of program health metrics.

Jansen, Michael↗

Juggling Act: Re-Planning and Building on Observatory...Simultaneously!

SOFIA (Stratospheric Observatory for Infrared Astronomy) is a major SMD program that has been required to meet several requirements and implement major planning and business initiatives overthe past 1 1/2 years, in the midst of system development and flight test phases. The program was required to implementing JCL and EVM simultaneously, as well as undergo a major replan and Standing Review Board - and all without impacting technical schedule progress. The team developed innovative processes that met all the requirements, and improved Program Management process toolsets. The SOFIA team, being subject to all the typical budget constraints, found ways to leverage existing roles in new ways to meet the requirements without creating unmanageable overhead. The team developed strategies and value added processes - such as improved risk identification, structured reserves management, cost/risk integration - so that the effort expended resulted in a positive return to the program.

Zavala, Eddie↗

Spaceflight Ka-Band High-Rate Radiation-Hard Modulator

A document discusses the creation of a Ka-band modulator developed specifically for the NASA/GSFC Solar Dynamics Observatory (SDO). This flight design consists of a high-bandwidth, Quadriphase Shift Keying (QPSK) vector modulator with radiation-hardened, high-rate driver circuitry that receives I and Q channel data. The radiationhard design enables SDO fs Ka-band communications downlink system to transmit 130 Mbps (300 Msps after data encoding) of science instrument data to the ground system continuously throughout the mission fs minimum life of five years. The low error vector magnitude (EVM) of the modulator lowers the implementation loss of the transmitter in which it is used, thereby increasing the overall communication system link margin. The modulator comprises a component within the SDO transmitter, and meets the following specifications over a 0 to 40 C operational temperature range: QPSK/OQPSK modulator, 300-Msps symbol rate, 26.5-GHz center frequency, error vector magnitude less than or equal to 10 percent rms, and compliance with the NTIA (National Telecommunications and Information Administration) spectral mask.

Jaso, Jeffery M.↗

Integrated Baseline Review (IBR) Handbook

An Integrated Baseline Review (IBR) is a review of a supplier?s Performance Measurement Baseline (PMB). It is conducted by Program/Project Managers and their technical staffs on contracts and in-house work requiring compliance with NASA Earned Value Management System (EVMS) policy as defined in program/project policy, NPR 7120.5, or in NASA Federal Acquisition Regulations. The IBR Handbook may also be of use to those responsible for preparing the Terms of Reference for internal project reviews. While risks may be identified and actions tracked as a result of the IBR, it is important to note that an IBR cannot be failed.

Source record↗

Improved Measurement of Ejection Velocities From Craters Formed in Sand

A typical impact crater is formed by two major processes: compression of the target (essentially equivalent to a footprint in soil) and ejection of material. The Ejection-Velocity Measurement System (EVMS) in the Experimental Impact Laboratory has been used to study ejection velocities from impact craters formed in sand since the late 1990s. The original system used an early-generation Charge-Coupled Device (CCD) camera; custom-written software; and a complex, multicomponent optical system to direct laser light for illumination. Unfortunately, the electronic equipment was overtaken by age, and the software became obsolete in light of improved computer hardware.

Cintala, Mark J.↗

Opportunities for Small Satellites in NASA's Earth System Science Pathfinder (ESSP) Program

NASA's Earth Venture class (EV) of missions are competitively selected, Principal Investigator (PI) led, relatively low cost and narrowly focused in scientific scope. Investigations address a full spectrum of earth science objectives, including studies of the atmosphere, oceans, land surface, polar ice regions, and solid Earth. EV has three program elements: EV-Suborbital (EVS) are suborbital/airborne investigations; EV-Mission (EVM) element comprises small complete spaceborne missions; and EV-Instrument (EVI) element develops spaceborne instruments for flight as Missions-of-Opportunity (MoO). To ensure the success of EV, frequent opportunities for selecting missions has been established in NASA's Earth Science budget. This paper will describe those opportunities and how the management approach of each element is tailored according to the specific needs of the element.

Peri, Frank↗