Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ELECTRIC ARCS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

Preliminary Development of Electrodes for an Electric-Arc Wind Tunnel

Two electrode configurations were tested in an electric-arc wind tunnel at the NASA Lewis Research Center. The results indicated approximately the same heat-loss rate per unit of arc power input for each of the configurations. Measured heat-loss rates were on the order of 40 percent of the arc power input. Nearly all this loss occurred at the anode. The power input and arc current limitations of the electrodes appear to be the critical design factors. Up to now, the maximum power to the stream has been 115 kilowatts with a cooled tungsten cathode and a cooled cylindrical anode incorporating a magnetic field. The maximum power input to this anode could not be established with the cooled tungsten cathode because cathode failures occurred at a gross power level of approximately 175 kilowatts. It was necessary to use a graphite cathode to seek the limitation of the anode. The results indicated that the anode limitation was primarily a function of arc current rather than power input. The anode was successfully operated at a power of 340 kilowatts at 1730 amperes; however, the anode failed with a power input of 324 kilowatts and a current of 2140 amperes. The magnetic flux density at the time of failure was 0.32 weber per square meter, or 3200 gauss. The graphite cathode was used only to establish the anode limitation; further investigation of graphite cathodes was discontinued because of the large amount of stream contamination associated with this type of electrode.

Shepard, Charles E.↗

Time Accurate Simulation of Nonequilibrium Flow Inside the NASA Ames Electric Arc Shock Tube

Numerical investigations of the flowfield inside NASA Ames' Electric Arc Shock Tube have been performed. The focus is to simulate the experiments designed to reproduce shock layer radiation layer relevant to Earth re-entry conditions. This paper assess the current computational capability in simulating time-accurate unsteady nonequilibrium flows in the presence of strong shock waves with state-of-the-art physical models. The technical approach is described with preliminary results presented for one specific flow condition. It was found that the axisymmetric source term generates a numerical instability that appears as shock bending. This instability is time dependent which greatly affects the shock speed. Post-shock conditions are discussed and compared to CEA equilibrium prediction and good agreement was obtained close to the test-section and just behind the shock.

Bensassi, Khalil↗

Carbonaceous Material Properties and Their Interactions with Slag During Electric Arc Furnace Steelmaking

The state of the interface between slag and carbon determines the slag foaming behavior and thus the effectiveness of carbon in electric arc furnace (EAF) steelmaking. This paper explores the interaction between synthetic slag and carbonaceous materials derived from various sources, including bio-char produced by two different technologies, graphite, coke, and char from tire pyrolysis. Different interfacial phenomena were found between slag and the carbonaceous materials examined. The interactions between bio-char and slag are found to be poor in comparison with other carbonaceous materials. Carbonaceous materials were characterized in terms of their chemical composition and the results obtained suggested that interfacial phenomena were not dominated by ash in the carbonaceous material. The effects of carbon crystalline structure on interaction with slag were evaluated by Raman spectroscopy and X-ray diffraction. Surface properties of the samples were evaluated using scanning electron microscopy, and surface morphology was identified as the principal factor affecting the interaction of slag on carbonaceous particles. The smooth surface of bio-char results in reduced slag foaming. This finding forms the basis for future research on the production of bio-char to be used as a slag foaming agent in EAF steelmaking.

36 MATERIALS SCIENCE↗

Enhanced Bottom Anode Monitoring in DC Electric Arc Furnaces Using Fiber-Optic Sensors

A pin style bottom anode employs conductive steel rods that serve as the pathway for the high electrical power through rammed refractory at the bottom of a DC Electric Arc Furnace (EAF). Anode wear during operation is important to monitor, as anode replacement is expensive and impacts EAF productivity. Liquid steel penetration into the un-sintered refractory layer can result from rapid electrical power ramp-up, dips in furnace temperature, or operating the anode for too long between EAF campaigns. In extreme cases, the liquid steel may penetrate the bottom of the furnace when anode wear progresses too close to the bottom shell, which is extremely dangerous and must be avoided. The current state of the art for monitoring bottom anode wear employs thermocouples imbedded in the anode pins at points in the anode. However, this approach is not sensitive enough to detect localized damage to the anode, especially when cracking occurs. Here, the present work utilizes fiber optic sensors to monitor the health of the anode, by creating a real-time spatially distributed temperature map of the anode. Unlike the traditional thermocouples, these sensors can be mounted at significantly greater depths, provide distributed temperature measurements, and can withstand temperatures of up to 900°C. Additionally, they are able to perform temperature measurements with a spatial resolution of 1.3 mm at a 5 Hz acquisition rate, providing unprecedented high-density real time monitoring of anode health and increasing the efficiency, and safety of EAF operation.

Bottom Anode↗

Time Accurate Simulation of Nonequilibrium Flow inside the NASA Ames Electric Arc Shock Tube

Numerical investigations of the ow field inside NASA Ames' Electric Arc Shock Tube have been performed. The focus is to simulate the experiments designed to reproduce shock layer radiation layer relevant to Earth re-entry conditions. This paper assess the current computational capability in simulating unsteady nonequilibrium flows in the presence of strong shock waves with state-of-the-art physical models. The technical approach is described with preliminary results presented for one specific ow condition. The numerical problems encountered during the computation of these flows are detailed, along with the methods used to resolve them. Post-shock conditions are discussed and compared to CEA equilibrium prediction.

Bensassi, Khalil↗

Boron Carbide Synthesis in Low-Voltage DC Electric Arc Initiated in Open Air

We describe a method of obtaining ultrafine boron carbide (B{sub 13}C{sub 2}) powder using the effect of a dc electric arc on a mixture of initial reactants containing carbon and boron. A peculiarity of the proposed method is that it can be implemented using arc discharge operating in open air without any vacuum equipment and protective inert gas atmosphere. X-ray diffraction data showed that the synthesized product in the general case contained three crystalline phases: boron carbide (B{sub 13}C{sub 2}), graphite (C), and boron oxide (B{sub 2}O{sub 3}). Electron-microscopic examination showed that the average size of boron carbide particles ranged from ~50 nm to ~2 μm.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

A sonic flow equation for electric arc jets

The relationship between total enthalpy and the flow parameters of two types of electric arc jets is discussed. A simple equation for the supersonic arc jet, based on ARCFLO code calculations for mass-average total enthalpy, is presented in terms of a sonic flow parameter. At enthalpies greater than about 25 MJ/kg, this equation shows better agreement with experimental arc jet data than a previous equation.

Shepard, Charles E.↗

Recycling Perspectives of Electric Arc Furnace Slag in the United States: A Review

This article presents a comprehensive review of electric arc furnace (EAF) slag recycling in the United States, examining its classification and the associated challenges and opportunities of its industrial use. The study affirms EAF slag's nonhazardous status. Here, the main challenges identified in EAF slag applications include substantial variations in composition and volume instability during/after hydration. Analysis of the U.S. recycling practices reveals that EAF slag is predominantly reused, with minimal landfill disposal. However, its prevalent use as a low value-added aggregate in construction applications underscores the industry's ongoing challenge to get additional value from EAF slag recycling. Despite these challenges, the study highlights a great potential for increased value extraction from EAF slag recycling. Beyond conventional applications as a clinker material for the cement industry, the review explores modern technologies for steelmaking slag recycling, revealing options for recovering valuable metals such as Cr, V, Mo, and Fe through methods such as leaching, reduction, and oxidation.

42 ENGINEERING↗

Full Facility Shock Frame Simulations of the Electric Arc Shock Tube

Radiative heating computations are performed for high speed lunar return experiments conducted in the Electric Arc Shock Tube (EAST) facility at NASA Ames Research Center. The nonequilibrium radiative transport equations are solved via NASA's in-house radiation code NEQAIR using flow field input from US3D flow solver. The post-shock flow properties for the 10 km/s Earth entry conditions are computed using the stagnation line of a blunt-body and a full facility CFD (Computational Fluid Dynamics) simulation of the EAST shock tube. The shocked gas in the blunt-body flow achieves a thermochemical equilibrium away from the shock front whereas EAST flow exhibits a nonequilibrium behavior due to strong viscous dissipation of the shock by boundary layer. The full-tube flow calculations capture the influence of the boundary layer on the shocked gas state and provide a realistic fluid dynamic input for the radiative predictions. The integrated radiance behind the shock is calculated in NEQAIR for wavelength regimes from Vacuum-UltraViolet (VUV) to InfraRed (IR), which are pertinent to the emission characteristics of high enthalpy shock waves in air. These radiance profiles are validated against corresponding EAST shots. The full-tube simulations successfully predict a sharp radiance peak at the shock front which gets smeared in the test data due to the spatial resolution in the measurements. The full facility based radiance behind the shock shows a slightly better match with the test data in the VUV and Red spectral regions, as compared to that from a blunt-body based predictions. The UV radiance is very similar for both geometries and under-predicts the test behavior. The IR test data matches better with the blunt-body based predictions where the full-tube simulations show a significant over-prediction.

Radiation↗

Full Facility Shock Frame Simulations of the Electric Arc Shock Tube

Radiative heating computations are performed for a range of high speed Earth entry experiments conducted in the Electric Arc Shock Tube at NASA Ames. The nonequilibrium radiative transport equations are solved in NEQAIR using flow field variables from the full facility CFD simulations of the EAST shock tube performed by US3D ow solver. These physics-based flow calculations lead to a significantly different post-shock gas state and associated radiation field as compared to that based on a simplified but computationally inexpensive calculation for flow over a blunt-body with appropriate initial conditions. The radiation spectra and radiance profiles are computed for an extensive range of wavelengths, from deep VUV to IR, which are pertinent to the emission characteristics of high enthalpy shock waves in air. The radiation properties of the shocked gas are calculated both in the nonequilibrium region at the shock, and in the equilibrium region behind the shock. Numerical predictions are found to be consistent with the experimental observations.

Simulations↗

Meteor Entry Characterization in the Electric Arc Shock Tube

This poster summarizes potential test opportunities in Ames' EAST facility that would benefit studies of meteor and asteroid entry into Earth's atmosphere. The Electric Arc Shock Tube (EAST) facility produces high speed (up to Mach 50) shockwaves at prescribed velocities, densities and atmospheric compositions.

Cruden, B. A.↗

Backshell Radiative Heating and Shock Layer Kinetic Measurement in NASA’s Electric Arc Shock Tube Facility

A methodology for creating incident shocks with similarity to the backshell radiative heating environment on planetary probes is presented. Two test series were carried out in the Electric Arc Shock Tube (EAST) at NASA Ames to quantify the backshell environment for planned and executed missions entering the atmospheres of Mars and Titan. The comparison of measured radiance in the shock tube to predicted post shock radiation levels is used to quantify the uncertainty in the model. This model uncertainty may then be related back to the flight condition to assess the error in the flight heating prediction. Tests for Mars entry show the shock tube measurements to be bracketed between two kinetic models by 2-7%. This suggests an 8% error in predicting the measured heating cannot be attributed to radiation. Comparisons to planned Titan entry suggest a substantial overprediction of the backshell radiation, which suggests opportunity for future refinement of radiative heating models.

radiation↗

Characterization of Titan Entry Radiative Heating in the Low Density Electric Arc Shock Tube

Prediction of aftbody radiative heating for Dragonfly’s entry at Titan requires accurate models to inform the design of its thermal protection systems. Previously reported investigations of shock layer aftbody radiation in the Electric Arc Shock Tube (EAST) at NASA Ames Research Center focused on the lower altitude/higher density part of the trajectory. This paper presents the first optical emission spectroscopy measurements of an ongoing test series in the new aluminum Low Density Shock Tube (LDST), recently installed at EAST, focusing on the radiative heating characterization through the higher altitude portion of Dragonfly’s entry path. Experimental data collected at a fill pressure of 0.1 Torr and shock velocities between 5.2 and 6.2 km/s show favorable agreement to similar conditions previously tested in the 4" High-Velocity Shock Tube, as well as improvements in the signal to noise ratio and available test time. Simulations employing DPLR and NEQAIR underpredict the experimental radiance, with increasing discrepancy from the NIR towards the UV wavelength range, thus motivating further efforts in improving the current non-Boltzmann model for the CN molecule.

A Fagnani↗

A stabilized low-frequency alternating-current electric arc

Establishing an arc between water-cooled tungsten-tipped electrodes, maintaining the arc along the centerline of a central jet of argon gas, and surrounding the argon jet with a coaxial sheath of nitrogen stabilizes operation of a low-frequency ac electric arc.

Lanzo, C. D.↗