Results for “Discrete Element Method” — Page 4

DOE OSTI2020

Measurement of flow properties coupled to experimental and numerical analyses of dense, granular flows for solar thermal energy storage

Granular flows of sintered bauxite proppants were researched along an inclined plane for solar thermal energy storage applications. Granular flow properties needed to drive numeric granular models were measured for improved numerical model predictions for Carbobead CP 50/140, 40/100, and 30/60 particles. Particle shape and size distributions were determined by coupling optical microscopy to an in-house image processing algorithm. The impulse excitation technique was used to measure elastic and shear moduli, and compute Poisson’s ratio. The coefficient of static sliding friction was measured using the slip-stick method, and the static rolling friction was determined from measured shear on particles positioned between two hot-pressed plates. The coefficient of restitution was measured by dropping particles on a surface and determining the kinetic energy before and after impact with the surface using high resolution particle tracking velocimetry. Particle size did not significantly impact the coefficients of restitution and static rolling friction, however, particle shape distribution resulted in a large variation in measurements. An inclined flow experiment was performed to characterize granular flows of Carbobead CP 30/60 particles using particle image velocimetry. Numerical models of the experiment using discrete element method were generated with the measured mechanical properties as inputs for comparison with experimental results. A constant directional torque rolling friction model best predicted bulk granular flow behavior. Furthermore, good agreement between the model and experiment was achieved at ambient, steady state conditions, with average velocity differences <10%.

14 SOLAR ENERGY↗

NASA NTRSDate not supplied

Computationally Guided Design of Polymer-Coated Microparticles as Reusable Materials

Long-duration space exploration missions and sustained lunar or Martian surface operations present greater demands for multifunctional and reusable materials. By scaling down the amount of material to be launched from Earth, both mission cost and risk can be reduced. In this regard, leveraging in-space manufacturing capabilities with reusable feedstock materials is an attractive option, as it will allow for articles to be generated on demand, utilized, and then recycled for additional use. NASA’s Enabling Sustained Presence Using Recyclables (ESPUR) project aims to develop reusable materials using polymer-coated microparticles that are bonded via reversible Diels-Alder reactions, where only modest heat is needed to trigger the reverse reaction and enable reuse. For proof-of-concept demonstration, research is currently focused on the fabrication of epoxy microparticles that contain a copoly(carbonate urethane) coating with maleimide and furan functionalities. Here, we discuss the integration of computational materials modeling approaches to help navigate the large design space in this development effort. We perform molecular dynamics (MD) simulations with atomistic and coarse-grained models of the copolymer, which allow us to evaluate the effects of design parameters like the molecular weight and composition on the molecular interactions and chain dynamics. We show how the properties change with the reversible bonds. We also leverage discrete element method (DEM) simulations to assess how microparticle design parameters like the size ratio and volume fraction can be tuned to increase the packing density and number of microparticle contacts to improve the mechanical properties. Our results demonstrate how computational tools can be used in close collaboration with experimental efforts to accelerate material design.

reusable materials↗

DOE OSTI2020

Scale bridging damage model for quasi-brittle metals informed with crack evolution statistics

Computationally efficient methods for bridging length scales, from highly resolved micro/meso-scale models that can explicitly model crack growth, to macro-scale continuum models that are more suitable for modeling large parts, have been of interest to researchers for decades. In this work, an improved brittle damage model is presented for the simulation of dynamic fracture in continuum scale quasi-brittle metal components. Crack evolution statistics, including the number, length, and orientation of individual cracks, are extracted from high-fidelity, finite discrete element method (FDEM) simulations and used to generate effective material moduli that reflect the material’s damaged state over time. This strategy allows for the retention of small-scale physical behaviors such as crack growth and coalescence in continuum scale hydrodynamic simulations. However, the high-fidelity simulations required to generate the crack statistics are computationally expensive. Thus, steps were taken to produce a flexible constitutive model to reduce the number of costly high-fidelity simulations needed to produce accurate results. A new stress based degradation criterion is introduced for the degradation of individual material zones. This allows for the development of a heterogeneous damage distribution within the bulk material. Then a flow stress model is added to the hydrodynamic simulation to account for plasticity in quasi-brittle materials. As a result, the effective moduli model can be applied to a larger range of materials. The effective moduli constitutive model is used to simulate beryllium flyer plate experiments. The results from the continuum scale simulations using statistics from a single high-fidelity simulation are found to be in excellent agreement with numerical and experimental velocity interferometer data. The same set of crack statistics are used to extrapolate the results of a higher rate flyer plate case using the effective moduli model. In conclusion, the extension of this model to higher rate cases shows promise for further reducing the number of costly high-fidelity simulations needed to generate crack statistics.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Powder spreading, densification, and part deformation in binder jetting additive manufacturing

Binder jetting additive manufacturing (AM) can print complex structures in economical and scalable manner. Binder jetting AM comprises of deposition and weak binding of particles, known as green part, at room temperature and subsequent binder removal and sintering densification at high temperatures. However, during the densification (i.e., sintering), the part significantly deforms due to volume shrinkage. The deformation during sintering is difficult to predict, which prevents the widespread application of this technology. In this research, powder spreading simulation using discrete element method (DEM) was performed first to capture local variations in powder bed configuration. Second, finite element method (FEM) with a phenomenological continuum constitutive model was used to predict part shrinkage during the sintering process. DEM simulation showed variations in packing density, particle segregation, formation of uneven powder bed surface, and shift in particle size distribution (PSD). The sintering simulation modeled part deformation with a reasonable accuracy of 3% for solid-state sintering and intermediate liquid phase sintering. A demonstration case with non-uniform initial packing density showed that inhomogeneous green part density and PSD should be accounted for prediction of part deformation in binder jetting AM.

36 MATERIALS SCIENCE↗

NASA NTRSDate not supplied

Monodisperse Single-Material Granular Tribocharging Modeling and Experimental Validation

Charge transfer between insulating grains has been a topic of interest for many years as this phenomenon is extremely important to many areas in industry. Of particular interest to NASA is the behavior of electrically insulative dust grains such as those found on the lunar surface. Whether poured from a scoop during sample collection activities, agitated inside a drum via mining robots, or fluidized by a gas plume, particle-particle interactions between similar granular materials will be widespread on the Moon. Designers hope to have a predictive model for how dust grains are charged, transported, and deposited on flight systems to better understand issues electrostatics may cause in future missions. While difference in work function is often seen as a driver for charge transfer between two materials, this is an incomplete representation for insulative particles. Other asymmetries in the system can also lead to charge being transferred: one such being the difference between static vs dynamic particles. Experiments performed under vacuum in the Electrostatics and Surface Physics Laboratory (ESPL) clearly show that particles having more contacts with other particles tend to charge positively and particles having fewer contacts tend to charge negatively, despite being made from the same material. During these experiments, monodisperse (population of single diameter) spherical particles were held in a reservoir which was then elevated at one end to slope into a Faraday cup used to measure bulk charge of the grains. Care was taken to limit the number of spheres bouncing out of the cup, to isolate the beads from the container itself so that only grain-to-grain interactions occurred, and to assure neutrality of the beads before the experiment began. A discrete element method (DEM) modeling package already incorporating many granular mechanics interactions was augmented to include the electrostatic behaviors seen in experiments. The model can reproduce the experimental results above by tracking the number of contacts between pairs of individual grains and applying a charge transfer condition related to this contact parameter. The experimental results as well as their incorporation into the improved modeling suite will be discussed. Future work includes adding additional asymmetries into the experiments/model such as polydisperse populations of spherical particles and irregularly shaped grains.

electrostatics↗

DOE OSTI2025

Effect of 3D-printed surface textures on wear mechanism in 3-body abrasion of soil

This study systematically investigates the enhancement of wear resistance in 3D printed surface textures through both experimental and theoretical approaches. Three distinct surface morphologies (Smooth Surface, Surface with uniformly distributed Pits, and Surface with uniformly distributed Bumps) were fabricated using High-Impact Polystyrene, where the meso-scale textures were precisely controlled through the 3D printing process. Wear behavior was evaluated using a 3-body wear tester in an abrasive particle environment, analyzing the influence of surface textures under various operating conditions. Systematic wear tests revealed that optimally designed surface textures achieved a remarkable 77 % reduction in wear compared to the worst-performing sample. The wear mechanisms were comprehensively characterized through weight loss measurements, Scanning Electron Microscopy (SEM), and Energy Dispersive Spectroscopy (EDS) analyses, elucidating the surface morphology changes and their interaction with wear particles. Notably, the study identified how the geometric characteristics of surface textures influence the movement of wear particles and the distribution of contact stresses. Discrete element method simulations corroborated the experimental findings, providing theoretical validation for the enhanced wear resistance of the optimal structure. The high correlation between simulated wear patterns and experimental results validates the reliability of the proposed design methodology. In conclusion, these results demonstrate that 3D printed surface texturing offers a cost-effective and scalable approach to significantly improve wear resistance in engineering applications, presenting a practical alternative to conventional, high-cost surface engineering methods.

3-body abrasion↗

NASA NTRSDate not supplied

Monodisperse Single-Material Granular Tribocharging Modeling and Experimental Validation

Charge transfer between insulating grains has been a topic of interest for many years as this phenomenon is extremely important to many areas in industry. Of particular interest to NASA is the behavior of electrically insulative dust grains such as those found on the lunar surface. Whether poured from a scoop during sample collection activities, agitated inside a drum via mining robots, or fluidized by a gas plume, particle-particle interactions between similar granular materials will be widespread on the Moon. Designers hope to have a predictive model for how dust grains are charged, transported, and deposited on flight systems to better understand issues electrostatics may cause in future missions. While difference in work function is often seen as a driver for charge transfer between two materials, this is an incomplete representation for insulative particles. Other asymmetries in the system can also lead to charge being transferred: one such being the difference between static vs dynamic particles. Experiments performed under vacuum in the Electrostatics and Surface Physics Laboratory (ESPL) clearly show that particles having more contacts with other particles tend to charge positively and particles having fewer contacts tend to charge negatively, despite being made from the same material. During these experiments, monodisperse (population of single diameter) spherical particles were held in a reservoir which was then elevated at one end to slope into a Faraday cup used to measure bulk charge of the grains. Care was taken to limit the number of spheres bouncing out of the cup, to isolate the beads from the container itself so that only grain-to-grain interactions occurred, and to assure neutrality of the beads before the experiment began. A discrete element method (DEM) modeling package already incorporating many granular mechanics interactions was augmented to include the electrostatic behaviors seen in experiments. The model can reproduce the experimental results above by tracking the number of contacts between pairs of individual grains and applying a charge transfer condition related to this contact parameter. The experimental results as well as their incorporation into the improved modeling suite will be discussed. Future work includes adding additional asymmetries into the experiments/model such as polydisperse populations of spherical particles and irregularly shaped grains.

granular↗

NASA NTRSDate not supplied

Simulations of Yarn Micro-Mechanics of Woven Heat Shield Materials

Carbon and phenolic fibers are commonly used in ablative thermal protection materials, such as 3-dimensional Mid-Density Carbon Phenolic (3MDCP), a 3D-woven composite comprised of mixed-fiber yarn bundles. Predicting the micro-mechanical response and fracture of twisted yarns composed of brittle and ductile fibers requires a modeling approach that captures per-fiber yielding, fiber fracture, and inter-fiber friction and contact. This work presents an extended bonded particle model (BPM) for discrete element method (DEM) simulation of fiber and yarn mechanics, implemented in LAMMPS. The model builds on the incremental bond formulation of Guo et al. and introduces a piecewise elasto-plastic constitutive law for axial extension, enabling representation of fibers that yield before failure. 3MDCP yarns were constructed using measured fiber radius distributions and helical twist geometry. Tensile simulations of single-ply 3MDCP yarns show good agreement with vender stress–strain results. Fiber breakage models also show details on yarn breakage propagration, centered radially in the yarn. Yarn breakage of multi-ply 3MDCP also matched experimental observations in per-ply breakage; however, predicted yarn breakage strength were found higher than experimental observations.

Discrete Element Method↗

NASA NTRSDate not supplied

Simulations of Yarn Micro-Mechanics of Woven Heat Shield Materials (3MDCP)

Carbon and phenolic fibers are commonly used in ablative thermal protection materials, such as 3-dimensional Mid-Density Carbon Phenolic (3MDCP), a 3D-woven composite comprised of mixed-fiber yarn bundles. Predicting the micro-mechanical response and fracture of twisted yarns composed of brittle and ductile fibers requires a modeling approach that captures per-fiber yielding, fiber fracture, and inter-fiber friction and contact. This work presents an extended bonded particle model (BPM) for discrete element method (DEM) simulation of fiber and yarn mechanics, implemented in LAMMPS. The model builds on the incremental bond formulation of Guo et al. and introduces a piecewise elasto-plastic constitutive law for axial extension, enabling representation of fibers that yield before failure. 3MDCP yarns were constructed using measured fiber radius distributions and helical twist geometry. Tensile simulations of single-ply 3MDCP yarns show good agreement with vender stress–strain results. Fiber breakage models also show details on yarn breakage propagration, centered radially in the yarn. Yarn breakage of multi-ply 3MDCP also matched experimental observations in per-ply breakage; however, predicted yarn breakage strength were found higher than experimental observations.

Woven↗

DOE OSTI2020

Numerical analyses of high temperature dense, granular flows coupled to high temperature flow property measurements for solar thermal energy storage

High temperature particle flow properties necessary to predict granular flow behavior for solar thermal energy storage applications were measured and calculated for Carbobead CP 30/60 up to 800 °C. Here, the measured properties included elastic and shear moduli, particle-particle coefficients of static sliding and rolling friction, and particle-particle coefficients of restitution. Poisson’s ratio was calculated with elastic and shear moduli. The flow properties were used as inputs for a numerical model using the discrete element method to examine granular flows along an inclined plane at high temperature. The flow behavior was strongly influenced by the coefficients of static friction, which impacted the particle residence time, shear effects from the side walls, and particle flow mass flux. An 8.7%, 15.6%, and 8.5% increase and 37.9% decrease in steady state mass flow rate was observed for 200 °C, 400 °C, 600 °C, and 800 °C, respectively, when compared to room temperature simulations. A 52%, 59%, and 33% decrease in the time to reach steady state was observed for 200 °C, 400 °C, and 600 °C, respectively, while a 53% increase in time was observed for 800 °C. A significant delay in the flow development at 800 °C was observed due to significantly higher frictional forces.

14 SOLAR ENERGY↗

DOE OSTI2020

Effect of Particle Spreading Dynamics on Powder Bed Quality in Metal Additive Manufacturing

Powder spreading precedes creation of every new layer in powder bed additive manufacturing (AM). The powder spreading process can lead to powder layer defects such as porosity, poor surface roughness and particle segregation. Therefore, the creation of homogeneous layers is the first task for optimal part printing. Discrete element methods (DEM) powder spreading simulations are typically limited to a single layer and/or small number of particles. Therefore, results from such model configurations may not be generalized to multiple layer processes. In this study, a computationally efficient multi-layer powder spreading DEM simulation model is proposed. The model is calibrated experimentally using static Angle of Repose measurements. The adhesion model parameter, cohesive energy density is related to adhesive surface energy and strain energy release rate parameters. The model results show that interaction between particle and the powder spreading rake leads to noticeable variation in packing density, surface roughness, dynamic angle of repose (AOR), particle size distribution, and particle segregation. Finally, the powder model is experimentally validated using a recoater spreading rig to measure the dynamic AOR at spreading speeds consistent with recoating speeds and layer heights used in AM processes.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Reverse scaling of a bonded-sphere DEM model: Formulation and application to lignocellulosic biomass microstructures

We explore scaling laws for adapting a bonded-sphere discrete element method (BS-DEM) model developed for woody structural mechanics at the millimeter scale to model the mechanics of realistic lignocellulosic biomass microstructures. Two scaling approaches, i.e., the reverse coarse graining (RCG) and equivalent bulk behavior (EBB), are proposed based on the classical mechanics principles and assessed in the single-particle compression and rectangular cuboid block tension tests. The EBB approach is recommended for BS-DEM models with general 3D geometries and is applied to simulate the microindentation test on a realistic microscale pinewood specimen. Simulations are performed to elucidate the impact of specimen thickness and loading position on the specimen’s force–deformation behavior. Furthermore, the range of Young’s modulus obtained from the calibrated BS-DEM simulations can match the experimental measurements. This is the first-of-its-kind study that has explored scale-bridging modeling approaches in biomass micromechanics and has proposed solutions based on BS-DEM models in the microscale.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2020

A Review of Computational Models for the Flow of Milled Biomass Part I: Discrete-Particle Models

Biomass is a renewable and sustainable energy resource. Current design of biomass handling and feeding equipment leverage both experiments and numerical modeling. This paper reviews the state-of-the-art discrete element methods (DEM) for the flow of milled biomass (Part I), accompanied by a comprehensive review on continuum-based computational models (Part II). The present review on DEM is primarily focused on the features and suitability of various particle shape models for different types of milled biomass because particle shape is the predominant attribute controlling the flow behavior of complex-shaped granular material. The general strengths and weaknesses in the applicability of those models for the milled biomass modeling are summarized. In particular, comments are provided to balance the numerical model capabilities and the computational cost for the development of DEM models. To our best knowledge, this is the first-of-its-kind review on DEM specifically for biomass. Our study indicates that the current DEM models require further development, calibration, and validation based on a deep understanding of biomass particle contact mechanics and experimental data support before they can be reliably used for predictive simulations in handling and feeding systems.

42 ENGINEERING↗

NASA NTRS2022

Investigating Particle-Particle Electrostatic Effects on Charged Lunar Dust Transport via Discrete Element Modeling

NASA surface exploration missions have always seen negative effects of dust including the Apollo missions. The astronaut-witnessed unusual behavior of the dust particles that surround the vehicle after engine cutoff has the potential to have more of an influence on surface systems dust loading than the high velocity lunar rocket plume ejecta in the landing process. The levitation and transport of the fine components of regolith on lunar surface has been linked to electrostatic effects and electric field, but so far there is no accurate model considering the inter-particle electrostatic interactions, especially when the particles are charged by rocket plume or other mechanical interactions due to exploration activities. This study is proposed to investigate the dynamics of charged lunar regolith with a discrete element method (DEM) approach focusing on the inter-particle interactions and contact charge transfer. The grain dynamics is coupled with mechanical and electrical particle interactions, and both short- and long-range interactions between spherical particles are incorporated. A tribo-charging model based on instantaneous collisions between particles is adopted and validated by comparing the simulation results to existing experimental data. Sensitivity analysis is conducted to quantify the effects of initial charge, tribo-charging, and E-field on transport of lunar dust based on JSC-1 simulants with a radius of 50 lm. DEM simulations are also conducted in a near realistic lunar environment with the estimations of initial conditions that shows the difference in position and velocity distributions between charged particles and uncharged particles. The results indicate that the charged dust particles have higher dispersion of position and velocity by several orders of magnitude due to electrostatic effects. This provides a potential explanation for the phenomena of the approximately 30 s dust lofting following Apollo Lunar Module landing.

Lunar dust↗

DOE OSTI2025

Predicting the evolution of biomass bulk density through feedstock preprocessing: Discrete element modeling, regression analysis, and pilot-scale validation

Bulk density is an important material property of biomass feedstocks, influencing handling, storage, transport costs, and conversion efficiency. In this study, predictive regression models for loose and tapped bulk densities of Alamo and Cave-in-Rock switchgrass are developed using a comprehensive dataset generated via calibrated bonded-sphere discrete element method (DEM) simulations. Here, a key contribution of this study is the use of a DEM-based approach, which correlates density with moisture content and particle size distribution parameters and enables analysis across a continuous particle size range, overcoming limitations of purely experimental data. For comparison, regression models are also developed using only experimental data from pilot-scale runs at the Biomass Feedstock National User Facility at Idaho National Laboratory. Validation against pilot-scale data showed reasonable prediction accuracy for both model types, particularly for smaller particle sizes (post-secondary grinding). While the experimental model showed slightly better performance matching the validation data in some cases, the DEM-based model benefits from a much larger dataset, reduced predictor multicollinearity, and continuous parameter coverage, highlighting the utility of validated simulation models for developing robust predictive tools for biomass preprocessing applications.

09 - BIOMASS FUELS↗

DOE OSTI2020

A numerical study of particle jetting in a dense particle bed driven by an air-blast

In this work, the particle jetting behavior in a blast-driven dense particle bed is studied at early times. Four-way coupled Euler–Lagrange simulations are performed using a high-order discontinuous Galerkin spectral element solver coupled with a high-order Lagrangian particle solver, wherein the inter-particle collisions are resolved using a discrete element method collision model. Following the experiments of Rodriguez et al. [“Formation of particle jetting in a cylindrical shock tube,” Shock Waves 23(6), 619–634 (2013)] and the simulations of Osnes et al. [“Numerical simulation of particle jet formation induced by shock wave acceleration in a Hele-Shaw cell,” Shock Waves 28(3), 451–461 (2018)], the simulations are performed in a quasi-two-dimensional cylindrical geometry (Hele-Shaw cell). Parametric studies are carried out to assess the impact of the coefficient of restitution and the strength of the incident shock on the particle jetting behavior. The deposition of vorticity through a multiphase (gas–particle) analog of Richtmyer–Meshkov instability is observed to play a crucial role in channeling the particles into well-defined jets at the outer edge of the particle bed. This is confirmed by the presence of vortex pairs around the outer jets. Furthermore, the effect of the relaxation of the relative velocity between the two phases on the vorticity generation is explored by analyzing the correlation between the radial velocity of particles and the radial velocity of the gas at the particle location.

42 ENGINEERING↗

DOE OSTI2023

Discrete element simulation of Pebble Bed Reactors on graphics processing units

Prediction of pebble positions in a Pebble Bed Reactor (PBR) is necessary for both reactor physics and thermal hydraulics simulations as the arrangement of pebbles has a significant impact on the resulting core power, coolant flow, and fuel temperature. Knowledge of pebble movement as the fuel is cycled through the core is also critical for predicting the fuel residence time and subsequently, the fuel burnup. Simulation with the Discrete Element Method (DEM) can provide knowledge of both the fuel packing and the fuel movement during cycling. Previous works that have performed 3D full-core DEM simulation of PBRs have used simplified models that neglect reflector wall features. This work employs a graphics processing unit (GPU)-enabled DEM code, Project Chrono, to analyze the differences in pebble packing and pebble velocities between a simplified smooth PBR reflector and a more realistic reflector that includes circular wall features. Additionally, a sensitivity study is performed on the depth of the wall features to ensure that crystallization is prevented. Project Chrono is also validated for PBR cycling applications using experimental data. It is found that wall features with a depth of at least 0.5 pebble diameters significantly reduce crystallization in the near-wall region, leading to discrepancies in both packing fraction and pebble velocity in this region compared to the simplified reflector models. These discrepancies are found to lead to roughly a 5–10% difference in the prediction of the near-wall porosity and a 10% difference in the prediction of the velocity of pebbles near the wall. As a result of these discrepancies, it is suggested that future DEM simulations of PBRs include wall features to reduce modeling errors.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2022

Flowability of Crumbler Rotary Shear Size-Reduced Granular Biomass: An Experiment-Informed Modeling Study on the Angle of Repose

Biomass has potential as a carbon-neutral alternative to petroleum for chemical and energy products. However, complete replacement of fossil fuel is contingent upon efficient processes to eliminate undesirable characteristics of biomass, e.g., low bulk density, variability, and storage-induced quality problems. Mechanical size reduction via comminution is a processing operation to engineer favorable biomass flowability in handling. Crumbler rotary shear mill has been empirically demonstrated to produce more uniformly shaped particles with higher flowability than hammermilled biomass. This study combines modeling and experimentation to unveil fundamental understandings of the relation between granular particle characteristics and biomass flow behavior, which elucidate underlying mechanisms and guide selection of critical processing parameters. For this purpose, the impact of critical material attributes, including particle size (2–6 mm), particle shape (briquette, chip, clumped-sphere, cube, etc.), and surface roughness, on the angle of repose (AOR) of milled pine chips were investigated using discrete element method (DEM) simulations. Forest Concepts Crumbler rotary shear system is used to produce milled pine particles within the same size range considered in DEM simulations. AOR of different sets of these particles were measured experimentally to benchmark DEM results against experimental data. Specific energy consumption for the comminution of biomass with different particle size and moisture content are measured for technoeconomic analysis. Our results show that the smaller size (2 mm) of pine particle achieves better followability (i.e., smaller AOR) while the energy cost of comminution is significantly higher and bulk density is almost the same as the 6-mm pine particles. For the 2-mm particle size, Crumbles from veneer have better flow properties than Crumbles from chips. Contrarily, no significant difference was observed between the AOR of the two materials for the 6-mm particle size. Furthermore, from DEM simulations, mechanical interlocking between particles was found as a dominant factor in determining AOR of complex-shaped particles such as milled pine, which cannot be accurately captured by using simple particle shapes (e.g., mono-sphere) with a rolling resistance model. Conversely, clumped-sphere model alleviates this limitation without increasing computational cost significantly and can be used for accurate representation of biomass granular particles when simulating free-flow behavior.

09 BIOMASS FUELS↗