Numerical and experimental investigation of turbulent DME jet flames.
Abstract not provided.
SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Abstract not provided.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Conference Paper
The composition of the solid electrolyte interphase (SEI) layers associated with a high performance Cu|Li cell using lithium bis(fluorosulfonyi)imide (LiFSI) in 1,2-dimethoxyethane (DME) as electrolyte is determined by a multinuclear (6Li, 19F, 13C and 1H) solid-state MAS NMR study at high magnetic field (850 MHz). This cell can be cycled at high rates (4 mA•cm-2) for more than 1000 cycles with no increase in the cell impedance at high Columbic efficiency (average of 98.4%) in a highly concentrated LiFSI-DME electrolyte (4 M). LiFSI, LiF, Li2O2 (and/or CH3OLi), LiOH, Li2S and Li2O are observed in the SEI and validated by comparing with the spectra acquired on standard compounds and literature reports. To gain further insight into the role of the solute and its concentration dependence on the formation of SEIs while keeping the solvent of DME unchanged, the SEIs from different concentrations of LiFSI-DME and lithium bis(trifluoromethanesulfonyl)imide (LiTFSI)-DME electrolyte are also investigated. It is found that LiF, a lithiated compound with superior mechanical strength and good Li+ ionic conductivity, is observed in the concentrated 4.0 M LiFSI-DME and the 3.0 M LiTFSI-DME systems but not in the diluted 1.0 M LiFSI-DME system. Li2O exists in both low and high concentration of LiFSI-DME while no Li2O is observed in the LiTFSI system. Furthermore, the dead metallic Li is reduced in the 4 M LiFSI-DME system compared with that in the 1 M LiFSI-DME system. Quantitative 6Li MAS results indicate that the SEI associated with the 4 M LiFSI-DEME is denser or thicker than that of the 1 M LiFSI-DME and the 3 M LiTFSI-DME systems. These findings are likely the reasons for explaining the high electrochemical performance associated with the high concentration LiFSI-DME system.
The research described in this product was performed in part in the Environmental Molecular Sciences Laboratory, a national scientific user facility sponsored by the Department of Energy's Office of Biological and Environmental Research and located at Pacific Northwest National Laboratory. The identity and reversibility of the elementary steps required for catalytic combustion of dimethyl ether (DME) on Pt clusters were determined by combining isotopic and kinetic analyses with density functional theory estimates of reaction energies and activation barriers to probe the lowest energy paths. Reaction rates are limited by C-H bond activation in DME molecules adsorbed on surfaces of Pt clusters containing chemisorbed oxygen atoms at near-saturation coverages. Reaction energies and activation barriers for C-H bond activation in DME to form methoxymethyl and hydroxyl surface intermediates show that this step is more favorable than the activation of C-O bonds to form two methoxides, consistent with measured rates and kinetic isotope effects. This kinetic preference is driven by the greater stability of the CH3OCH2* and OH* intermediates relative to chemisorbed methoxides. Experimental activation barriers on Pt clusters agree with density functional theory (DFT)-derived barriers on oxygen-covered Pt(111). Measured DME turnover rates increased with increasing DME pressure, but decreased as the O2 pressure increased, because vacancies (*) on Pt surfaces nearly saturated with chemisorbed oxygen are required for DME chemisorption. DFT calculations show that although these surface vacancies are required, higher oxygen coverages lead to lower C-H activation barriers, because the basicity of oxygen adatoms increases with coverage and they become more effective in hydrogen abstraction from DME. Water inhibits reaction rates via quasi-equilibrated adsorption on vacancy sites, consistent with DFT results indicating that water binds more strongly than DME on vacancies. These conclusions are consistent with the measured kinetic response of combustion rates to DME, O2, and H2O, with H/D kinetic isotope effects, and with the absence of isotopic scrambling in reactants containing isotopic mixtures of 18O2-16O2 or 12CH3O12CH3-13CH3O13- CH3. Turnover rates increased with Pt cluster size, because small clusters, with more coordinatively unsaturated surface atoms, bind oxygen atoms more strongly than larger clusters and exhibit lower steadystate vacancy concentrations and a consequently smaller number of adsorbed DME intermediates involved in kinetically relevant steps. These effects of cluster size and metal-oxygen bond energies on reactivity are ubiquitous in oxidation reactions requiring vacancies on surfaces nearly saturated with intermediates derived from O2.
In a recent series of articles, Gebremariam, Bogner, and Duguet derived a microscopically based nuclear energy density functional by applying the density matrix expansion (DME) to the Hartree-Fock energy obtained from chiral effective field theory two- and three-nucleon interactions. Owing to the structure of the chiral interactions, each coupling in the DME functional is given as the sum of a coupling constant arising from zero-range contact interactions and a coupling function of the density arising from the finite-range pion exchanges. Because the contact contributions have essentially the same structure as those entering empirical Skyrme functionals, a microscopically guided Skyrme phenomenology has been suggested in which the contact terms in the DME functional are released for optimization to finite-density observables to capture short-range correlation energy contributions from beyond Hartree-Fock. The present article is the first attempt to assess the ability of the newly suggested DME functional, which has a much richer set of density dependencies than traditional Skyrme functionals, to generate sensible and stable results for nuclear applications. The results of the first proof-of-principle calculations are given, and numerous practical issues related to the implementation of the new functional in existing Skyrme codes are discussed. Using a restricted singular value decomposition optimization procedure, it is found that the new DME functional gives numerically stable results and exhibits a small but systematic reduction of our test {chi}{sup 2} function compared to standard Skyrme functionals, thus justifying its suitability for future global optimizations and large-scale calculations.
NH 3 and DME dual fuel oxidation and kinetic coupling are experimentally studied by using a supercritical pressure jet-stirred reactor (SP-JSR) at 20 and 100 atm, over a temperature range of 500–900 K, and at fuel-lean and stoichiometric conditions with NH 3 to DME molar ratios of 4 and 0.62, respectively. An HP-Mech model for high-pressure NH3/DME oxidation is developed based on our previous studies and it shows generally better performance than other models in the literature on high-pressure oxidation experiments. Due to DME’s strong low-temperature reactivity, it dramatically enhances the oxidation of NH3 at low temperature. However, the effect of NH 3 on DME oxidation varies with temperature. At low temperatures, NH 3 inhibits low-temperature reactivity by consuming OH radicals. In addition, the NH 2 and NO x formation from NH 3 further suppresses the low-temperature DME reactivity by reducing alkylperoxyl and O 2 QOOH radicals via RO 2 + NH 2 = RO + H 2 NO, RO 2 + NO = RO + NO 2 and O 2 QOOH + NO = 2CH 2 O + HO 2 + NO 2 . At intermediate temperatures, due to enhanced kinetic coupling of NH 2 /NO x /HO 2 chemistry, DME oxidation is significantly promoted. It is found that there are two major NH 2 /NO x /HO 2 coupling pathways for OH radical production brought by NH 3 : (1) NH 2 + HO 2 = H 2 NO + OH and (2) NH 2 + NO 2 = H 2 NO + NO with NO + HO 2 = OH + NO 2 . Moreover, the resulting H 2 NO will further contribute to OH production via the H 2 NO/NO x /HONO coupling pathways: H 2 NO + NO 2 = HNO + HONO, HNO + NO 2 = HONO + NO, and HONO (+M) = OH + NO (+M). These new NH 2 /NO x /HO 2 and H 2 NO/NO x /HONO pathways play a critical role in promoting DME oxidation at intermediate temperatures. Novelty and Significance Statement: Blending NH 3 with DME can significantly enhance the reactivity of NH 3 and facilitate its practical application in advanced internal combustion engines. NH 3 /DME oxidation is studied in a novel supercritical pressure jet-stirred reactor up to 100 atm, a much higher pressure than previous studies. An interesting non-monotonic effect of NH3 addition on fuel oxidation has been found. Unique kinetic couplings of NH2/HO2/NOx and H2NO/NOx/HONO brough by NH3 and DME blending are identified to play important roles in radical generation and reactivity promotion. The valuable experimental data and key kinetics revealed in the current work can tremendously improve our understanding of NH 3 /DME oxidation via NO x /RO 2 and NH 2 / H 2 NO/HO 2 /NO x kinetic couplings at low to intermediate temperatures.
A Pd/ZnO/Al2O3 catalyst was developed for the synthesis of methanol and dimethyl ether (DME) from syngas. Studied were temperatures of operation ranging from 250°C to 380°C. High temperatures (e.g. 380°C) are necessary when combining methanol and DME synthesis with a methanol to gasoline (MTG) process in a single reactor bed. A commercial Cu/ZnO/Al2O3 catalyst, utilized industrially for the synthesis of methanol at 220-280°C, suffers from a rapid deactivation when the reaction is conducted at high temperature (>320°C). On the contrary, a Pd/ZnO/Al2O3 catalyst was found to be highly stable for methanol and DME synthesis at 380°C. The Pd/ZnO/Al2O3 catalyst was thus further investigated for methanol and DME synthesis at P=34-69 bars, T= 250-380°C, GHSV= 5 000-18 000 h-1, and molar feeds H2/CO= 1, 2, and 3. Selectivity to DME increased with decreasing operating temperature, and increasing operating pressure. Increased GHSV’s and H2/CO syngas feed ratios also enhanced DME selectivity. Undesirable CH4 formation was observed, however, can be minimized through choice of process conditions and by catalyst design. By studying the effect of the Pd loading and the Pd:Zn molar ratio the formulation of the Pd/ZnO/Al2O3 catalyst was optimized. A catalyst with 5% Pd and a Pd:Zn molar ratio of 0.25:1 has been identified as the preferred catalyst. Results indicate that PdZn particles are more active than Pdº particles for the synthesis of methanol and less active for CH4 formation. A correlation between DME selectivity and the concentration of acid sites of the catalysts has been established. Hence, two types of sites are required for the direct conversion of syngas to DME: 1) PdZn particles are active for the synthesis of methanol from syngas, and 2) acid sites which are active for the conversion of methanol to DME. Additionally, CO2 formation was problematic as PdZn was found to be active for the water-gas-shift (WGS) reaction, under all the conditions evaluated.
Characteristics of polycyclic aromatic hydrocarbon (PAH) and soot formation in counterflow diffusion flames of methane, ethane, propane, and ethylene fuels mixed with dimethyl ether (DME) have been investigated. Planar laser-induced incandescence and fluorescence techniques were employed to measure relative soot volume fractions and PAH concentrations, respectively. Results showed that even though DME is known to be a clean fuel in terms of soot formation, DME mixture with ethylene fuel increases PAH and soot formation significantly as compared to the pure ethylene case, while the mixture of DME with methane, ethane, and propane decreases PAH and soot formation. Numerical calculations adopting a detailed kinetics showed that DME can be decomposed to produce a relatively large number of methyl radicals in the low-temperature region where PAH forms and grows; thus the mixture of DME with ethylene increases CH{sub 3} radicals significantly in the PAH formation region. Considering that the increase in the concentration of O radicals is minimal in the PAH formation region with DME mixture, the enhancement of PAH and soot formation in the mixture flames of DME and ethylene can be explained based on the role of methyl radicals in PAH and soot formation. Methyl radicals can increase the concentration of propargyls, which could enhance incipient benzene ring formation through the propargyl recombination reaction and subsequent PAH growth. Thus, the result substantiates the importance of methyl radicals in PAH and soot formation, especially in the PAH formation region of diffusion flames. (author)
Ion-solvent interactions in non-aqueous electrolytes are of fundamental interest and practical importance, yet debates regarding ion preferential solvation and coordination numbers persist. In this work, in situ liquid SIMS was used to examine ion-solvent interactions in three representative electrolytes, i.e., lithium hexafluorophosphate (LiPF6) at 1.0 M in ethylene carbonate (EC)-dimethyl carbonate (DMC), and lithium bis(fluorosulfonyl)imide (LiFSI) at both low (1.0 M) and high (4.0 M) concentrations in 1,2-dimethoxyethane (DME). In the positive ion mode, solid molecular evidence strongly supports the preferential solvation of Li+ by EC. Besides, from the negative spectra, we also found that PF6- forms association with EC, which has been neglected by previous studies due to the relatively weak interaction. While in both LiFSI in DME electrolytes, no evidence shows that FSI- is associated with DME. Furthermore, strong salt ion cluster signals were observed in the 1.0 M LiPF6 in EC-DMC electrolyte, suggesting that a significant amount of Li+ ions stay in vicinity of anions. In sharp comparison, weak ion cluster signals were detected in dilute LiFSI in DME electrolyte, suggesting most ions are well separated, in agreement with our molecular dynamics (MD) simulation results. These findings indicate that with virtues of little bias on detecting positive and negative ions and the capability of directly analyzing concentrated electrolytes, in situ liquid SIMS is a powerful tool that can provide key evidence for improved understanding on the ion-solvent interactions in non-aqueous electrolytes. Therefore, we anticipate wide applications of in situ liquid SIMS on investigations of various ion-solvent interactions in the near future.
Solvent-driven separations may enable scalable concentration of hypersaline brines, supporting a circular resource economy from the extraction of lithium and rare earth elements from spent battery and magnet leachates. This work analyses a novel solvent-driven water extraction (SDWE) system employing dimethyl ether (DME) and ultra-low-grade heat for brine concentration and fractional crystallization. SDWE exploits DME’s unique properties: (1) a low dielectric constant that promotes water solubility over charged solutes by a factor of 10 3 , and (2) a high volatility that facilitate efficient DME reconcentration with ultra-low-grade heat. The techno-economic viability of SDWE is assessed with a computational framework that encompasses a liquid–liquid separator and a solvent concentrator. We integrate the extended universal quasichemical model with the virial equation of state to predict the compositions of the complex three-phase DME-water mixture at vapor–liquid and liquid–liquid equilibrium. Subsequently, we optimize the thermodynamic and economic performance of SDWE, by controlling the interstage flash pressure, heat source temperature, and the number of concentrating stages. DME-based SDWE concentrates an input saline feed to 5.5 M and regenerates over 99 % of the DME using ultra-low-grade heat below 50 °C, with a DME/water selectivity ratio of 125. Here our calculations reveal that optimal performance is achieved at interstage flash pressures of 0.4 – 0.5 bar for heat source temperatures between 323–373 K, with improved exergetic efficiencies at lower temperatures. At a heat source temperature of 323 K and an interstage pressure of 0.489 bar, DME-driven SDWE achieves an optimal thermodynamic efficiency of 20.5 % and a projected specific cost of US$ 1.93 m -3 . These specific costs suggest that SDWE is competitive with commercialized thermal distillation technologies, while mitigating the traditional risks associated with scaling in heat and mass exchangers with hypersaline brines.
Purpose: To evaluate the dose-mapping error (DME) inherent to conventional dose-mapping algorithms as a function of dose-matrix resolution. Methods: As DME has been reported to be greatest where dose-gradients overlap tissue-density gradients, non-clinical 66 Gy IMRT plans were generated for 11 lung patients with the target edge defined as the maximum 3D density gradient on the 0% (end of inhale) breathing phase. Post-optimization, Beams were copied to 9 breathing phases. Monte Carlo dose computed (with 2*2*2 mm{sup 3} resolution) on all 10 breathing phases was deformably mapped to phase 0% using the Monte Carlo energy-transfer method with congruent mass-mapping (EMCM); an externally implemented tri-linear interpolation method with voxel sub-division; Pinnacle’s internal (tri-linear) method; and a post-processing energy-mass voxel-warping method (dTransform). All methods used the same base displacement-vector-field (or it’s pseudo-inverse as appropriate) for the dose mapping. Mapping was also performed at 4*4*4 mm{sup 3} by merging adjacent dose voxels. Results: Using EMCM as the reference standard, no clinically significant (>1 Gy) DMEs were found for the mean lung dose (MLD), lung V20Gy, or esophagus dose-volume indices, although MLD and V20Gy were statistically different (2*2*2 mm{sup 3}). Pinnacle-to-EMCM target D98% DMEs of 4.4 and 1.2 Gy were observed ( 2*2*2 mm{sup 3}). However dTransform, which like EMCM conserves integral dose, had DME >1 Gy for one case. The root mean square RMS of the DME for the tri-linear-to- EMCM methods was lower for the smaller voxel volume for the tumor 4D-D98%, lung V20Gy, and cord D1%. Conclusion: When tissue gradients overlap with dose gradients, organs-at-risk DME was statistically significant but not clinically significant. Target-D98%-DME was deemed clinically significant for 2/11 patients (2*2*2 mm{sup 3}). Since tri-linear RMS-DME between EMCM and tri-linear was reduced at 2*2*2 mm{sup 3}, use of this resolution is recommended for dose mapping. Interpolative dose methods are sufficiently accurate for the majority of cases. J.V. Siebers receives funding support from Varian Medical Systems.
In this work, we have been developing a three-step conversion of biomass-derived syngas to methanol to dimethyl-ether (DME) to non-aromatic hydrocarbons for use as high-octane gasoline and sustainable aviation fuel. This process produces branched alkanes from DME using a Cu/BEA catalyst and is a promising alternative to other syngas conversion processes such as Fischer-Tropsch to linear alkanes and traditional ZSM-5 catalyzed methanol to aromatic gasoline. In this short article we describe some advances in our understanding related to separations and purification via the use of more detailed experimental speciation in an updated process model involving multiple phase equilibrium-based separation steps. Primary modeled reactor outlet constituents (and weight %) are: C3 and lighter hydrocarbon gases (11.1%), C4s (54.5%), H 2 (1.2%), CO 2 (2.9%), water (5.0%), unreacted DME (16.5%), methanol (2.3%), and C5+ hydrocarbons (6.4%). DME (the primary reactant) and H 2 recycle and reuse are important for the overall process efficiency, and the recycle of C4s is important to increase the C5+ yield via reactivation and homologation. Thus H 2 , C4s, and DME are targeted for recycle, while methanol and water need to be removed from the product to conform with fuel specifications. Model predictions from Aspen Plus using the NRTL-RK property method indicate a fuel composition with C5+ content of 97.1 wt%, with minor constituents: 2.4 wt% C4s, 0.3 wt% methanol, 0.1 wt% DME, 0.03 wt% water, and 0.01 wt% C3s. These ranges of minor components conform with fuel quality requirements, and the modeled product is amenable for unconstrained blending to boost gasoline octane ratings.
We distinguish rates at which carbon deposition occurs during initiation, rates at which catalytic centers are lost during deactivation, and paraffin-to-olefin ratio during propagation as benchmarks that distinguish 5 wt% Cu/H-BEA and H-BEA (Si/Al = 13.5) catalysts during dimethyl ether (DME) homologation in the presence of hydrogen. Studies that systematically vary initial DME contact time (210, 94, and 45 mol H+, initial s (mol C ) -1 ), DME pressure (4 and 22 kPa), and H 2 pressure (1, 24, and 48 kPa) reveal that Cu enables lower carbon deposition rates (on a per proton basis) in the induction period, increases the effluent paraffin-to-olefin ratio during propagation, and decreases the instantaneous site-loss yields by a factor of ~ 1.5-2x (moles of active sites lost per mole of DME) during termination sequences thus affecting the degree of product saturation and catalyst stability during DME homologation. Furthermore, these results provide mechanistic insights revealing the critical role of Cu in facilitating DME homologation to high value, high-octane gasoline-range hydrocarbons with higher cumulative turnovers than proton form H-BEA.
Dewatering highly saline aqueous streams, from mining and geothermal leachates to industrial wastewater, is essential for effective resource recovery and safe disposal. Membraneless water extraction (MWE) uses a low-polarity solvent to separate water from concentrated aqueous solutions. In this study, we design a new MWE that uses dimethyl ether (DME) to selectively extract water from high-salinity brines, leveraging the volatility of DME to achieve rapid solvent recovery. By separating water and dissolved salts at a liquid–liquid interface, MWE minimizes the deleterious effects of scaling on vulnerable membrane and heat exchanger surfaces, reducing the need for extensive pretreatment and expensive materials. We begin by developing a computational framework for a multistage counterflow liquid–liquid contactor, which extracts water into DME, coupled with a multistage solvent regenerator that uses vapor compression to efficiently separate the desalinated water from the DME extractant. Excess Gibbs free energy and equation of state frameworks are used to model fluid phase equilibria in water–DME–sodium chloride (NaCl) mixtures, with interaction parameters estimated from experimental data. Incorporating equilibrium calculations into a system-scale computational model, we examine the performance of MWE using DME for the first time. Our analysis demonstrates that MWE can concentrate seawater desalination brine (>1.0 mol NaCl kg –1 ) to zero-liquid discharge salinities, with an energy consumption of under 50 kW h per m 3 of water extracted with a solvent recovery ratio greater than 99.9%. We highlight the importance of staging the vapor compression process to simultaneously minimize energy consumption while enabling brine concentration and product water solvent contamination. Finally, the thermodynamic framework developed here allows for the robust evaluation of new MWE solvents and systems for critical brine concentration and fractional precipitation applications.
The diffusion behavior of Mg 2+ in electrolytes is not as readily accessible as that from Li + or Na + utilizing PFG NMR, due to the low sensitivity, poor resolution, and rapid relaxation encountered when attempting 25 Mg NMR. In MgTFSI 2 /DME solutions, “bound” DME (coordinating to Mg 2+ ) and “free” DME (bulk) are distinguishable from 1 H NMR. With the exchange rates between them obtained from 2D 1 H EXSY NMR, we can extract the self-diffusivities of free DME and bound DME (which are equal to that of Mg 2+ ) before the exchange occurs using PFG diffusion NMR measurements coupled with analytical formulas describing diffusion under two-site exchange. Further, the high activation enthalpy for exhange (65–70 kJ/mol) can be explained by the structural change of bound DME as evidenced by its reduced C–H bond length. Comparison of the diffusion behaviors of Mg 2+ , TFSI – , DME, and Li + reveals a relative restriction to Mg 2+ diffusion that is caused by the long-range interaction between Mg 2+ and solvent molecules, especially those with suppressed motions at high concentrations and low temperatures.