Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Constants”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

Optical constants of polycrystalline Al 0.25 Ga 0.75 P and Al 0.9 Ga 0.1 As determined by variable-angle spectroscopic ellipsometry

The optical constants of single-crystal Al x Ga 1-x P and Al x Ga 1-x As have been widely studied at various Al compositions but have not yet been thoroughly investigated as polycrystalline materials. Using variable-angle spectroscopic ellipsometry, we estimate and analyze the optical constants of polycrystalline Al 0.25 Ga 0.75 P and Al 0.9 Ga 0.1 As that were non-epitaxially deposited at deposition temperatures of either 250 or 420 °C, and with various dopant species, dopant concentrations, and V/III flux ratios. Here, for wavelengths of 350–400 nm, decreasing the V/III ratio increases the refractive index of Be-doped polycrystalline Al 0.25 Ga 0.75 P. For wavelengths >500 nm, as the targeted Be dopant concentration increases for polycrystalline Al 0.25 Ga 0.75 P, the amount the extinction coefficient increases and the indirect bandgap decreases depends on the V/III ratio. Furthermore, Si-doped polycrystalline Al 0.25 Ga 0.75 P has significantly smaller extinction coefficient values than when it is Be-doped, for the same V/III ratio and targeted doping concentration, at wavelengths >500 nm. Based on our findings, we hypothesize that the dopant species, dopant concentration, and the V/III ratio dictate various types of defect concentrations, which then affect the optical constants and indirect bandgap of polycrystalline Al 0.25 Ga 0.75 P. Additionally, for wavelengths >500 nm, we find that polycrystalline Al 0.25 Ga 0.75 P and Al 0.9 Ga 0.1 As have the lowest extinction coefficient values when deposited at 420 °C, as opposed to 250 °C. Thus, we hypothesize that the deposition temperature is the most significant factor in dictating the optical constants of these polycrystalline III-Vs. Ultimately, this work demonstrates alternative methods to tune the optical constants of polycrystalline Al 0.25 Ga 0.75 P and Al 0.9 Ga 0.1 As, as opposed to tuning the Al composition.

42 ENGINEERING↗

Multigroup Constant Calculation with Static α-Eigenvalue Monte Carlo for Time-Dependent Neutron Transport Simulations

Herein, multigroup constants for deterministic methods that preserve the time-dependent physics of the neutron transport equations are derived. Alternative multigroup constant weighting spectra are discussed: (1) the fundamental k-eigenfunction, (2) the fundamental α-eigenfunction, and (3) a composite of several α-modes. To generate the fundamental α-eigenfunction for calculating the multigroup constants, a static fundamental α-eigenvalue method is implemented into the open source Monte Carlo code OpenMC. Several static and kinetic problems are devised to verify the implementations and to investigate the relative performance of the alternative multigroup constant weighting spectra. Results emphasize that as a multigroup constant weighting spectrum, the fundamental α-eigenfunction offers physical characteristics that make it advantageous (in producing accurate solutions) over the typically used fundamental k-eigenfunction.

42 ENGINEERING↗

Sensitivity Coefficients Calculated for the Prompt Neutron Decay Constant At or Near Delayed Critical

The derivation of a non-invasive prompt neutron decay constant sensitivity coefficient is provided in this work. The computation of the sensitivity coefficient derived in this work does not require modification of Monte Carlo source code and is based on capabilities available in Monte Carlo N-Particle R© Code Version 6.2. The prompt neutron decay constant sensitivity coefficients are calculated for 44-group and 252-group energy structures for specific nuclide-reaction pairs in the Jezebel benchmark experiment. The nuclide-reaction pairs investigated in this work include Pu- 239(n,f), Pu-240(n,f), and Pu-241(n,f). Physical explanations of the sensitivity profiles exhibited by the 252-group energy structure are investigated for the prompt neutron multiplication factor, mean neutron lifetime, and prompt neutron decay constant. The prompt neutron decay constant sensitivity coefficients calculated for the 44-group and 252-group energy structure of Pu-239(n,f) are compared. Lastly, the 44-group energy structure sensitivity coefficients calculated are used for nuclear-data induced uncertainty quantification of the neutron multiplication factor. This work shows that a reduction in the nuclear data-induced uncertainty of the neutron multiplication factor is possible for all nuclide-reaction pairs investigated when prompt neutron decay constant sensitivity coefficients are utilized. This is important for new critical experiment design optimization studies of measurement configurations. This work provides a basis for more detailed sensitivity analysis and uncertainty quantification of nuclide, reaction, and energy-specific cross section data.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Pilgrim : A thermal rate constant calculator and a chemical kinetics simulator

Pilgrim is a program written in Python and designed to use direct dynamics in the calculation of thermal rate constants of chemical reactions by the variational transition state theory (VTST), based on electronic structure calculations for the potential energy surface. Pilgrim can also simulate reaction mechanisms using kinetic Monte Carlo (KMC). For reaction processes with many elementary steps, the rate constant of each of these steps can be calculated by means of conventional transition state theory (TST) or by using VTST. In the current version, Pilgrim can evaluate thermal rates using the canonical version of reaction-path VTST, which requires the calculation of the minimum energy path (MEP) associated with each elementary step or transition structure. Multi-dimensional quantum effects can be incorporated through the small-curvature tunneling (SCT) approximation. These methodologies are available both for reactions involving a single structure of the reactants and the transition state and also for reactions involving flexible molecules with multiple conformations of the reactant and/or of the transition state. For systems with many conformers, the program can evaluate each of the elementary reaction rate constants by multipath canonical VTST or multi-structural VTST. Moreover, the reactant can be unimolecular or bimolecular. Torsional anharmonicity can be incorporated through either the MSTor or the Q2DTor programs. Dual-level calculations are also available in Pilgrim: automatic high-level single-point energies can be used to correct the energy of reactants, transition states, products, and MEP points using the interpolated single-point energies (ISPE) algorithm. When the rate constants of all the chemical processes of interest are known, by means of their calculation using Pilgrim or alternatively through analytical fits to the rate constants as functions of temperature, it is possible to simulate a multistep mechanism under specified laboratory conditions using KMC. Finally, this algorithm allows performing a kinetic simulation to monitor the evolution of each chemical species with time and obtain the product yields.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Five percent measurement of the gravitational constant in the Large Magellanic Cloud

We perform a novel test of General Relativity by measuring the gravitational constant in the Large Magellanic Cloud (LMC). The LMC contains six well-studied Cepheid variable stars in detached eclipsing binaries. Radial velocity and photometric observations enable a complete orbital solution, and precise measurements of the Cepheids’ periods permit detailed stellar modelling. Both are sensitive to the strength of gravity, the former via Kepler’s third law and the latter through the gravitational free-fall time. We jointly fit the observables for stellar parameters and the gravitational constant. Performing a full Markov Chain Monte Carlo analysis of the parameter space including all relevant nuisance parameters, we constrain the gravitational constant in the Large Magellanic Cloud relative to the Solar System to be G LMC /G SS = $0.93{^{+0.05}_{-0.04}}$. We discuss the implications of this 5% measurement of Newton’s constant in another galaxy for dark energy and modified gravity theories. This result excludes one Cepheid, CEP-1812, which is an outlier and needs further study: it is either a highly unusual system to which our model does not apply, or it prefers G LMC < G SS at 2.6σ. We also obtain new bounds on critical parameters that appear in semi-analytic descriptions of stellar processes. In particular, we measure the mixing length parameter to be $α = 0.90{^{+0.36}_{-0.26}}$ (when assumed to be constant across our sample), and obtain constraints on the parameters describing turbulent dissipation and convective flux.

79 ASTRONOMY AND ASTROPHYSICS↗

A Reconfigurable Planar Capacitor Sensor for Thru the Jacket Dielectric Constant Measurement of Cable Insulation

Planar capacitor sensors have been proposed to measure the aging-related dielectric constant variation of the jacket or insulation materials of cables. Although capacitor sensors have been used to monitor the aging of cable insulation by removing the jacket, through the jacket measurement of cable insulation dielectric constant variation is difficult because once the sensor is placed on the jacket it would either measure the aging of the jacket or that of the jacket and insulation together. A reconfigurable sensor along with innovative cable-specific models could be used to determine the jacket and insulation aging using the same sensor. For the proposed novel reconfigurable sensor, the electric field penetration depth is changed by activating and deactivating PIN diode switches. In one instance, the sensor measures the dielectric constant variation of the jacket, while in the next, it measures the dielectric constant variation of both the jacket and the insulation. Here, by leveraging previously developed capacitance estimation models from large-scale finite element simulations for a specific cable, these two sets of measurement data are used to evaluate the aging-related dielectric constant variation of the insulation. Experimental data from aged cable specimens are presented to demonstrate the operation of the sensor.

47 OTHER INSTRUMENTATION↗

Experimental determination of the solubility constant of kurnakovite, MgB3O3(OH)5·5H2O

In this study, I present experimental results on the equilibrium between boracite [Mg 3 B 7 O 13 C1(cr)] and kurnakovite [chemical formula, Mg 2 B 6 O 11 ·15H 2 O(cr); structural formula, MgB 3 O 3 (OH) 5 ·5H 2 O(cr)] at 22.5 ± 0.5 °C from a long-term experiment up to 1629 days, approaching equilibrium from the direction of supersaturation, Mg 3 B 7 O 13 C1(cr) + H + + 2B(OH)$^-_4$ + 18H 2 O(1) ⇌ 3MgB 3 O 3 (OH) 5 ·5H 2 O(cr) + C1 - . Based on solubility measurements, the 10-based logarithm of the equilibrium constant for the above reaction at 25 °C is determined to be 12.83 ± 0.08 (2σ). Based on the equilibrium constant for dissolution of boracite, Mg 3 B 7 O 13 C1(cr) + 15H 2 O(1) = 3Mg 2+ + 7B(OH)$^-_4$ + C1 - + 2H + at 25 °C measured previously (Xiong et al. 2018) and that for the reaction between boracite and kurnakovite determined here, the equilibrium constant for dissolution of kurnakovite, MgB 3 O 3 (OH) 5 ·5H 2 O(cr) = Mg 2+ + 3B(OH)$^-_4$ + H + + H 2 O(1) is derived as -14.11 ± 0.40 (2σ). Using the equilibrium constant for dissolution of kurnakovite obtained in this study and the experimental enthalpy of formation for kurnakovite from the literature, a set of thermodynamic properties for kurnakovite at 25 °C and 1 bar is recommended as follows: Δ H $^0_f$ = -4813.24 ± 4.92 kJ/mol, Δ G$^0_f$ = -4232.0 ± 2.3 kJ/mol, and S 0 = 414.3 ± 0.9 J/(mol·K). Among them, the Gibbs energy of formation is based on the equilibrium constant for kurnakovite determined in this study; the enthalpy of formation is from the literature (Li et al. 1997), and the standard entropy is calculated internally with the Gibbs-Helmholtz equation in this work. The thermodynamic properties of kurnakovite estimated using the group contribution method for borate minerals based on the sums of contributions from the cations, borate polyanions, and structural water to the thermodynamic properties from the literature (Li et al. 2000) are consistent, within their uncertainties, with the values listed above. Since kurnakovite usually forms in salt lakes rich in sulfate, studying the interactions of borate with sulfate is important to modeling kurnakovite in salt lakes. Finally, for this purpose, I have re-calibrated our previous model (Xiong et al. 2013) describing the interactions of borate with sulfate based on the new solubility data for borax in Na 2 SO 4 solutions presented here.

36 MATERIALS SCIENCE↗

H-H, C-H, and C-C NMR spin-spin coupling constants calculated by the FP-INDO method for aromatic hydrocarbons

The FP-INDO (finite perturbation-intermediate neglect of differential overlap) method is used to calculate the H-H, C-H, and C-C coupling constants in hertz for molecules of six different benzenoid hydrocarbons: benzene, naphthalene, biphenyl, anthracene, phenanthrene, and pyrene. The calculations are based on both the actual and the average molecular geometries. It is found that only the actual molecular geometries can always yield the correct relative order of values for the H-H coupling constants. For the calculated C-C coupling constants, as for the calculated C-H coupling constants, the signs are positive (negative) for an odd (even) number of bonds connecting the two nuclei. Agreements between the calculated and experimental values of the coupling constants for all six molecules are comparable to those reported previously for other molecules.

Long, S. A. T.↗

Measurement of the solar constant

The absolute value of the solar constant and the long term variations that exist in the absolute value of the solar constant were measured. The solar constant is the total irradiance of the Sun at a distance of one astronomical unit. An absolute radiometer removed from the effects of the atmosphere with its calibration tested in situ was used to measure the solar constant. The importance of an accurate knowledge of the solar constant is emphasized.

Crommelynck, D.↗

The photochemical time constants of minor constituents and their families in the middle atmosphere

A comprehensive formula is worked out for the photochemical time constant of minor constituents in the middle atmosphere. The formula is particularly useful for evaluating the time constants for families of some chemical species that are strongly coupled by rapid exchange reactions. Height profiles of photochemical time constants are calculated for individual species and their families based on the chemical reaction rate constants recommended in the recent WMO and JPL reports. Potential exchange reactions among various family members are discussed, and the effects of the choice of family membership on the time constant are evaluated.

Shimazaki, T.↗

X-ray nebular models. II - Constant pressure clouds

Models are presented for the ionization and temperature structure of X-ray illuminated gas clouds under the assumption that the clouds' pressure is fixed. Models are considered which have a variety of different combinations of X-ray source spectrum and cloud pressure, characteristic of galactic X-ray sources and interstellar gas. It is shown that optically thick constant pressure clouds obey scaling laws for their ionized column densities which are analogous to the scaling behavior of constant density models. The results of constant pressure models are contrasted with constant density model results, and it is shown that the constant pressure assumption leads to enhanced thermal instability effects and also causes important differences in the line spectra emergent from X-ray illuminated clouds. Observable consequences for X-ray illuminated interstellar clouds are discussed.

Kallman, T. R.↗

Temperature and pressure dependence of the absolute rate constant for the reactions of NH2 radicals with acetylene and ethylene

The absolute rate constants for the reaction between the NH2 free radical and acetylene and ethylene is measured experimentally using a flash photolysis technique. The constant is considered to be a function of temperature and pressure. At each temperature level of the experiment, the observed pseudo-first-order rate constants were assumed to be independent of flash intensity. The results of the experiment indicate that the bimolecular rate constant for the NH2 + C2H2 reaction increases with pressure at 373 K and 459 K but not at lower temperatures. Results near the pressure limit conform to an Arrhenius expression of 1.11 (+ or -) 0.36 x 10 to the -13th over the temperature range from 241 to 459 K. For the reaction NH2 + C2H4, a smaller rate of increase in the bimolecular rate constant was observed over the temperature range 250-465 K. The implications of these results for current theoretical models of NH2 + C2H2 (or H4) reactions in the atmospheres of Jupiter and Saturn are discussed.

Bosco, S. R.↗

Active region influences upon the solar constant

The influence that active regions have upon the solar constant is discussed. Sunspots appear to lower the solar constant for the few days in which they are located near central meridian. This raises the possibility that an 11-year, solar-cycle-related depression in the solar constant may occur. Recent findings concerning the physics of active regions suggest that sunspots and faculae are largely surface features. Within that surface faculae reradiate, within a few weeks, the 'missing energy' associated with sunspots. This is consistent with the observations showing that the solar constant does not have an 11-year cycle-related depression that some authors predicted. However, there is a secular variation in the solar constant, whose explanation is not completely understood.

Schatten, Kenneth H.↗

Estimation of the engineering elastic constants of a directionally solidified superalloy for finite element structural analysis

The temperature-dependent engineering elastic constants of a directionally solidified nickel-base superalloy were estimated from the single-crystal elastic constants of nickel and MAR-MOO2 superalloy by using Wells' method. In this method, the directionally solidified (columnar-grained) nickel-base superalloy was modeled as a transversely isotropic material, and the five independent elastic constants of the transversely isotropic material were determined from the three independent elastic constants of a cubic single crystal. Solidification for both the single crystals and the directionally solidified superalloy was assumed to be along the (001) direction. Temperature-dependent Young's moduli in longitudinal and transverse directions, shear moduli, and Poisson's ratios were tabulated for the directionally solidified nickel-base superalloy. These engineering elastic constants could be used as input for performing finite element structural analysis of directionally solidified turbine engine components.

Abdul-Aziz, Ali↗

Optical constants of solid methane

Methane is the most abundant simple organic molecule in the outer solar system bodies. In addition to being a gaseous constituent of the atmospheres of the Jovian planets and Titan, it is present in the solid form as a constituent of icy surfaces such as those of Triton and Pluto, and as cloud condensate in the atmospheres of Titan, Uranus, and Neptune. It is expected in the liquid form as a constituent of the ocean of Titan. Cometary ices also contain solid methane. The optical constants for both solid and liquid phases of CH4 for a wide temperature range are needed for radiative transfer calculations, for studies of reflection from surfaces, and for modeling of emission in the far infrared and microwave regions. The astronomically important visual to near infrared measurements of solid methane optical constants are conspicuously absent from the literature. Preliminary results are presented of the optical constants of solid methane for the 0.4 to 2.6 micron region. K is reported for both the amorphous and the crystalline (annealed) states. Using the previously measured values of the real part of the refractive index, n, of liquid methane at 110 K n is computed for solid methane using the Lorentz-Lorentz relationship. Work is in progress to extend the measurements of optical constants n and k for liquid and solid to both shorter and longer wavelengths, eventually providing a complete optical constants database for condensed CH4.

Khare, Bishun N.↗

Rate constants for the reactions of OH with HFC-134a (CF3CH2F) and HFC-134 (CHF2CHF2)

Measurements of rate constants for HFC-134 (CF2HCF2H) relative to CH3CCl3, HFC-125, and HFC-134a are reported. The measurements were made in a slow-flow, temperature controlled photochemical reactor, and were based on relative rates of disappearance of the parent compounds as measured by FTIR spectroscopy. Hydroxyl radicals were generated by 254-nm photolysis of O3 in the presence of water vapor. NASA/JPL rate constants for the reference compounds are used to derive temperature-dependent rate constants of both compounds. Rate constants obtained from the different reference compounds are in excellent agreement. The presently recommended rate constant for HFC-134a is about 25 percent too high.

Demore, W. B.↗

A measurement of the Hubble constant from the X-ray properties and the Sunyaev-Zel'dovich effect of Abell 2218

The distance of the cluster of galaxies Abell 2218, and hence the value of the Hubble constant, has been measured by comparing the X-ray properties and the Sunyaev-Zel'dovich effect of the cluster. The result for the Hubble constant is H(sub zero) = 65 +/- 25 km/s/MPC, where the error includes the random and systematic errors, combined in quadrature, and the largest contributions to the overall error come from systematic errors in the Sunyaev-Zel'dovich effect data and in the X-ray spectrum of the cluster. The X-ray and Sunyaev-Zel'dovich effect data are consistent with the same model for the intergalactic medium in Abell 2218 (an isothermal Beta-model with Beta is about 0.65 and cluster core radius about 1.0 min). A prevous report of a smaller Hubble constant, found by applying the same method on the same cluster, is shown to be based on a model for the cluster gas that is inconsistent with the Einstein IPC data. The present result for the Hubble constant is consistent with the value found earlier for the cluster Abell 665: by combining the results of the method for both clusters we conclude that the value of the Hubble constant is H(sub zero) = 55 +/- 17 km/s/MPC.

Birkinshaw, M.↗

Calculation of kinetic rate constants from thermodynamic data

A new scheme for relating the absolute value for the kinetic rate constant k to the thermodynamic constant Kp is developed for gases. In this report the forward and reverse rate constants are individually related to the thermodynamic data. The kinetic rate constants computed from thermodynamics compare well with the current kinetic rate constants. This method is self consistent and does not have extensive rules. It is first demonstrated and calibrated by computing the HBr reaction from H2 and Br2. This method then is used on other reactions.

Marek, C. John↗