SEARCH · Engineering Papers

Results for “CYLINDRICAL CONFIGURATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

All sources NASA NTRS DOE OSTI

NASA NTRS1987

Three-step cylindrical seal for high-performance turbomachines

A three-step cylindrical seal configuration representing the seal for a high performance turbopump (e.g., the space shuttle main engine fuel pump) was tested under static (nonrotating) conditions. The test data included critical mass flux and pressure profiles over a wide range of inlet temperatures and pressures for fluid nitrogen and fluid hydrogen with the seal in concentric and fully eccentric positions. The critical mass flux (leakage rate) was 70% that of an equivalent straight cylindrical seal with a correspondingly higher pressure drop based on the same flow areas of 0.3569 sq cm but 85% that of the straight seal based on the third-step flow area of 0.3044 sq cm. The mass flow rates for the three step cylindrical seal in the fully eccentric and concentric positions were essentially the same, and the trends in flow coefficient followed those of a simple axisymmetric inlet configuration. However, for inlet stagnation temperatures less than the thermodynamic critical temperature the pressure profiles exhibited a flat region throughout the third step of the seal, with the pressure magnitude dependent on the inlet stagnation temperature. Such profiles represent an extreme positive direct stiffness. These conditions engendered a crossover in the pressure profile upstream of the postulated choke that resulted in a local negative stiffness. Flat and crossover profiles resulting from choking within the seal are practically unknown to the seal designer. However, they are of critical importance to turbomachine stability and must be integrated into any dynamic analysis of a seal of this configuration. In addition, choking is highly dependent on geometry, inlet-to-backpressure ratio, and inlet temperature and can occur within the seal even though the backpressure is above the critical pressure.

Hendricks, Robert C.↗

DOE OSTI2021

Evaluation of external tubular configurations for a high-temperature chloride molten salt solar receiver operating above 700°C

Next-generation concentrating solar power (CSP) tower technologies target operating temperatures exceeding 700°C to increase the thermal-to-electric conversion efficiency. Molten chloride salts are one possible alternative to current commercial molten nitrate salts to enable the higher operating temperature. This paper analyzes the predicted optical, thermal-fluids, and structural performance of traditional external tubular solar receiver configurations applied with a chloride salt heat transfer fluid (HTF) and inlet/outlet temperatures of 500°C/735°C, and considers sensitivity analysis and optimization relative to receiver sizing, tube sizing, number of panels, flow circuit configurations, and solar flux concentration under constraints on internal velocity, pressure drop, wall thickness, and required creep-fatigue lifetime. The high temperature conditions increase the significance of inelastic deformation mechanisms such as creep relative to that expected in commercial 565°C nitrate salt designs. High-temperature creep and creep-fatigue damage in the metal alloy tubes are the key factors that limit allowable solar flux concentration and achievable receiver thermal efficiency at the near-800°C wall temperature conditions. For a traditional external cylindrical receiver configuration, the design parameters and conditions capable of satisfying all constraints produced, at best, a design point receiver efficiency of 78.2%, or 80.5% when excluding receiver intercept efficiency. Variation in the optimal receiver performance relative to uncertainty in the binding maximum velocity, minimum wall thickness, and minimum lifetime constraints is presented.

14 SOLAR ENERGY↗

DOE OSTI2021

A most misunderstood conditionally-solvable quantum-mechanical model

Highlights: • The Schrödinger equation for some quantum-mechanical models is separable in cylindrical coordinates. • The radial equation exhibits harmonic, linear and Coulomb-like interactions. • The Frobenius method leads to three-term recurrence relations. • Some particular energies are obtained from truncation of the recurrence relation. • Many authors misunderstood these results. In this paper we show that several authors have derived wrong physical conclusions from a gross misunderstanding of the exact eigenvalues and eigenfunctions of a conditionally-solvable quantum-mechanical model. It consists of an eigenvalue equation with seemingly Coulomb, linear and harmonic terms. Here we compare the results derived by those authors with the actual eigenvalues of the models calculated by means of the Ritz variational method.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

DOE OSTI2023

Dynamics of quarks and gauge fields in the lowest-energy states in QED and QCD interactions

We examine the dynamics of quarks and gauge fields in the lowest energy states in the QED and QCD interactions by combining Schwinger’s longitudinal confinement in (1+1)D with Polyakov’s transverse confinement in (2+1)D in a “stretch (2+1)D” flux tube model in (3+1)D. For such QED and QCD systems in the flux tube configuration with cylindrical symmetry, we separate out the transverse and longitudinal degrees of freedom, approximate the non-Abelian QCD in the quasi-Abelian approximation, and solve the derived equations to study the collective excitations. Here, we find stable collective QED and QCD excitations showing up as confined QED and QCD mesons, in support of previous theoretical studies and recent observations of the anomalous hypothetical X17 and E38 particles. Future theoretical lattice gauge calculations of QED in (3+1)D with the inclusion of the Schwinger longitudinal confinement mechanism and experimental confirmation of the hypothetical X17 and E38 particles will shed definitive light on quark confinement in the QED interaction in (3+1)D.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

NASA NTRS1966

Study and applications of retrodirective and self-adaptive electromagnetic wave controls to a Mars probe Quarterly report, 1 Jan. - 31 Jul. 1966

Cylindrical antenna configurations spinning around axes examined for effects on received or transmitted CW signal spectrum

MODULATED CONTINUOUS WAVE↗

NASA NTRS1972

Factors which influence the analysis and design of ejector nozzles

A theoretical analysis of the viscous interaction between the primary and secondary streams of ejector nozzles was developed. The analysis accounts for real sonic line effects and the streamwise variation in stream mixing and boundary layer within the ejector. The aspects of the analysis are explained and illustrated by applying the theory to a variety of ejector configurations including cylindrical shroud, contoured flap and plug nozzles. Extensive comparisons are made between theory and data to show the importance of various analytical assumptions and such design variables as diameter ratio, spacing ratio, total temperature ratio, and primary nozzle geometry.

Anderson, B. H.↗

NASA NTRS1972

Factors which influence the analysis and design of ejector nozzles.

A theoretical analysis of the viscous interaction between the primary and secondary streams of ejector nozzles was developed. The analysis accounts for real sonic-line effects and the streamwise variation in stream mixing and boundary layer within the ejector. The aspects of the analysis are explained and illustrated by applying the theory to a variety of ejector configurations including cylindrical shroud, contoured flap and plug nozzles. Extensive comparisons are made between theory and data to show the importance of various analytical assumptions and such design variables as diameter ratio, spacing ratio, total temperature ratio, and primary nozzle geometry.

Anderson, B. H.↗

NASA NTRS1970

A solenoid failure detection system for cold gas attitude control jet valves

The development of a solenoid valve failure detection system is described. The technique requires the addition of a radioactive gas to the propellant of a cold gas jet attitude control system. Solenoid failure is detected with an avalanche radiation detector located in the jet nozzle which senses the radiation emitted by the leaking radioactive gas. Measurements of carbon monoxide leakage rates through a Mariner type solenoid valve are presented as a function of gas activity and detector configuration. A cylindrical avalanche detector with a factor of 40 improvement in leak sensitivity is proposed for flight systems because it allows the quantity of radioactive gas that must be added to the propellant to be reduced to a practical level.

Johnston, P. A.↗

NASA NTRS1982

Analytical and experimental investigation of stator endwall contouring in a small axial-flow turbine. 1: Stator performance

Three stator configurations were studied to determine the effect of stator outer endwall contouring on stator performance. One configuration was a cylindrical stator design. One contoured stator configuration had an S-shaped outer endwall, the other had a conical-convergent outer endwall. The experimental investigation consisted of annular surveys of stator exit total pressure and flow angle for each stator configuration over a range of stator pressure ratio. Radial variations in stator loss and aftermixed flow conditions were obtained when these data were compared with the analytical results to assess the validity of the analysis, good agreement was found.

Haas, J. E.↗

NASA NTRS1982

Large-aperture interferometer using local reference beam

A large-aperture interferometer was devised by adding a local-reference-beam-generating optical system to a schlieren system. Two versions of the interferometer are demonstrated, one employing 12.7 cm (5 in.) diameter schlieren optics, the other employing 30.48 cm (12 in.) diameter parabolic mirrors in an off-axis system. In the latter configuration a cylindrical lens is introduced near the light source to correct for astigmatism. A zone plate is a satisfactory decollimating element in the reference-beam arm of the interferometer. Attempts to increase the flux and uniformity of irradiance in the reference beam by using a diffuser are discussed.

Howes, W. L.↗

NASA NTRS1985

Convective Oscillations at Crystal/Melt Interface

Oscillatory instability in shape of solid/liquid interface geometry observed in heat-transfer experiments in long, thin vertical cylinder filled with succinonitrile. Novel fluid flow configuration with cylindrical symmetry developed to permit detailed heat flow experiments in geometry also mathematically tractable.

Glicksman, M.↗

NASA NTRS1984

Large-aperture interferometer with local reference beam

Howes, W. L.↗

NASA NTRS1987

Straight cylindrical seal for high-performance turbomachines

A straight cylindrical seal configuration representing the seal for a high-performance turbopump (e.g., the space shuttle main engine fuel pump) was tested under static (nonrotating) conditions. The test data included critical mass flux and pressure profiles over a wide range of inlet temperatures and pressures for fluid nitrogen and fluid hydrogen with the seal in concentric and fully eccentric positions. The critical mass fluxes (or leakage rates) for the concentric and fully eccentric configurations were nearly the same when based on stagnation conditions upstream of the seal. The fully eccentric configuration pressure profiles of the gas and liquid were different. Further, the pressure differences between the maximum and the minimum clearance positions were highly dependent on the geometric conditions, the temperature, and the absolute pressure at both the inlet and the exit. The pressure differences were greatest in the inlet region. The results, although complex, tend to follow the corresponding-states principles for critical flows. Gaseous injection near the seal exit plane significantly altered the pressure profiles and could be used to control turbomachine instabilities.

Hendricks, Robert C.↗

NASA NTRS1989

The dynamics of charged particles in the near wake of a very negatively charged body - Laboratory experiment and numerical simulation

A numerical simulation that is cylindrical in configuration space and three-dimensional in velocity space has been initiated to test a model for the near-wake dynamics of a very negatively charged body, with reference to the plasma environment around spacecraft. The simulation parameters were closely matched to those of a laboratory experiment so that the results can be compared directly. The laboratory study showed that the electrons and ions can display different temporal features in the filling-in of the wake; and that they can both be found within one body diameter of an object with a highly negative body potential. It was also found that the temperature of the electrons in the very near wake could be somewhat colder than the ambient value, suggesting the possibility of a filtering mechanism being operative there. The simulation results to date largely corroborate the density findings.

Morgan, M. Alvin↗

NASA NTRS2002

Analysis, Design and Optimization of Non-Cylindrical Fuselage for Blended-Wing-Body (BWB) Vehicle

Initial results of an investigation towards finding an efficient non-cylindrical fuselage configuration for a conceptual blended-wing-body flight vehicle were presented. A simplified 2-D beam column analysis and optimization was performed first. Then a set of detailed finite element models of deep sandwich panel and ribbed shell construction concepts were analyzed and optimized. Generally these concepts with flat surfaces were found to be structurally inefficient to withstand internal pressure and resultant compressive loads simultaneously. Alternatively, a set of multi-bubble fuselage configuration concepts were developed for balancing internal cabin pressure load efficiently, through membrane stress in inner-stiffened shell and inter-cabin walls. An outer-ribbed shell was designed to prevent buckling due to external resultant compressive loads. Initial results from finite element analysis appear to be promising. These concepts should be developed further to exploit their inherent structurally efficiency.

Mukhopadhyay, V.↗

NASA NTRS1991

Numerical simulation of shrouded propellers

A numerical model was developed for the evaluation of the performance characteristics of a shrouded propeller. Using this model, a computational study was carried out to investigate the feasibility of improving the aerodynamic performance of a propeller by encasing it in a shroud. The propeller blade was modeled by a segmented bound vortex positioned along the span of the blade at its quarter-chord-line. The shroud was modeled by a number of discrete vortex rings. Due to the mutual dependence of shroud and propeller vortex strengths and the propeller vortex wake an iterative scheme was employed. Three shroud configurations were considered: a cylindrical and two conical shrouds. The computed performance of the shrouded propeller was compared with that of a free propeller of identical propeller geometry. The numerical results indicated that the cylindrical shroud outperformed the conical shroud configurations for the cases considered. Furthermore, when compared to the free propeller performance, the cylindrical shroud showed a considerable performance enhancement over the free propeller. However, the improvements were found to decrease with an increase in the advance ratio and to virtually diminish at advance ratios of about 2.5.

Afjeh, Abdollah A.↗

NASA NTRS1986

Behavior of a non-wetting melt in free fall - Theoretical

In a previous paper the experimental equilibrium configurations of a nonwetting liquid in an ampoule were described. Theoretical analyses of these configurations are described here. In a cylindrical ampoule a bubble/bridge configuration is predicted to be stable only up to a critical volume of gas, beyond which separated columns of liquid form. This critical bubble volume decreases as the contact angle of the liquid on the ampoule increases. In a triangular ampoule the liquid contacts the ampoule along the center of the faces and not in the corners. As the contact angle increases beyond 90 deg, the contact width decreases.

Sen, Radha↗

NASA NTRS2001

Method of Making a Composite Tank

A composite tank for containing liquid oxygen and the method of making the same wherein a water-soluble mandrel having the desired tank configuration and a cylindrical A method of making a composite tank for containing liquid oxygen configuration of the mandrel and an outer boss conforming to the configuration of the inner boss, the bosses each having a tubular portion for receiving the protuberance on the mandrel and a spherical portion. The mandrel and the bosses are first coated with a nickel coating. The mandrel is then wrapped with graphite fibers wetted with an epoxy resin and this resin is cured. A layer of insulating foam is then applied to the tank and cured. The insulating foam is machined to a desired configuration and a layer of aramid fibers wetted with a second epoxy resin is wrapped around the tank. The second resin is cured and the water soluble mandrel is washed from inside the tank.

Thomas K DeLay↗