Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “COMPRESSION STRENGTH”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Mechanical Properties of High-Temperature Fiber-Reinforced Thermoset Composites with Plain Weave and Unidirectional Carbon Fiber Fillers

Fiber-reinforced thermoset composites are a class of materials that address the arising needs from the aerospace and hypersonic industries for high specific strength, temperature-resistant structural materials. Among the high-temperature resistant thermoset categories, phenolic triazine (PT) cyanate esters stand out thanks to their inherent high degradation temperature, glass transition temperature, and mechanical strength. Despite the outstanding properties of these thermosets, the performance of carbon fiber composites using PT cyanate esters as matrices has not been thoroughly characterized. This work evaluated PT and carbon fiber composites’ compressive properties and failure mechanisms with different fiber arrangements. A PT resin with both plain weave (PW) and non-crimped unidirectional (UD) carbon fiber mats was analyzed in this research. Highly loaded thermoset composites were obtained using process temperatures not exceeding 260 °C, and the composites proved to retain compressive strength at temperatures beyond 300 °C. Compressive testing revealed that PT composites retained compressive strength values of 50.4% of room temperature for UD composites and 61.4% for PW composites. Post-compressive failure observations of the gage section revealed that the mechanisms for failure evolved with temperature from brittle, delamination-dominant failure to shear-like failure promoted by the plastic failure of the matrix. This study demonstrated that PT composites are a good candidate for structural applications in harsh environments.

Hall, Samuel Ernesto↗
DOE OSTI2021

Mechanical and physical properties of inorganic polymer cement made of iron-rich laterite and lateritic clay: A comparative study

In this work, two different laterites (iron contents of 13.07 and 49.34 wt%, respectively, for lateritic clay, LAC, and iron-rich laterite, LAI) were selected and calcined at 600 °C. The obtained calcined laterites, namely LAI600 and LAC600, were separately mixed with an alkaline solution (silicate modulus of 1.35) or an acidic solution (phosphoric acid solution at pH ≤ 2) for the synthesis of inorganic polymer products. The fabricated products were cured at 20 °C (ambient) and 40 °C (oven). The obtained results showed that the compressive strength of each series of alkaline-based inorganic polymer binder increased with ageing time (7 and 28 days) for room temperature curing, while the reverse trend was noted for oven-cured specimens. The best mechanical performance was obtained when using a phosphoric acid solution, 38 and 52 ± 1 MPa; 62 and 65 ± 1 MPa at 28 days for LAC and LAI respectively. It appeared that a higher iron content within the laterite contributed to an increase in the compressive strength under acidic conditions (LAI (59 MPa) > LAC (48 MPa)) compared to the behavior obtained under alkaline conditions (LAI (6 MPa) < LAC (29 MPa)). Accordingly, the acidic products exhibited a dense structure (with lower porosity) and contained amorphous iron/aluminium phosphate phases such as berlinite (FePO{sub 4}), iron hydrogen phosphate hydrate (Fe{sub 3}H{sub 15}(PO{sub 4}){sub 8·}4H{sub 2}O), ferrowyllieite (AlFe{sub 2}Na{sub 2}(PO{sub 4}){sub 3}) and sodium iron phosphate (Na{sub 3}Fe{sub 2}(PO{sub 4}){sub 3}) arising from the alteration of iron minerals in an acidic medium, confirmed by Mössbauer spectroscopy and electron paramagnetic resonance spectroscopy.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Influence of CaO/FeO ratio on the formation mechanism and properties of alkali-activated Fe-rich slags

Highlights: • Effect of the CaO/FeO molar ratio in alkali-activated Fe-rich slags is unraveled. • Low CaO/FeO molar ratios enhance the early kinetics and compressive strength. • Reaction extent and strength further increase with higher CaO/FeO ratio after 7 days. • Fe{sup 2+}-trioctahedral layers of the binder are hydroxylated and in a silicate phase. • The final strength is determined by the influence of Ca on the reaction products. In the search for CO{sub 2} mitigating cement technologies, alkali-activated Fe-rich slags present a possible alternative. The influence of the chemical composition of the synthetic Fe-silicate slag on the reaction mechanisms is assessed by varying the CaO/FeO molar ratio. The alkali-activated Fe-rich slags consist of trioctahedral layers that are shown to be hydroxylated and in contact with silicates, in a similar way to phyllosilicate minerals. The formation of this phyllosilicate-like structure is hindered during the first days for samples with high CaO/FeO ratios, because of the partial incorporation of Ca in the trioctahedral layers. At later ages, the samples with higher CaO/FeO ratios gain in reaction extent, to exceed the reaction extent of low CaO/FeO ratios at 28 days and beyond. The increase in compressive strength is even more pronounced than the effect on the reaction extent, which underlines the importance of Ca on the inherent strength of the binding phases.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Multi-scale investigation on mechanical behavior and microstructural alteration of C-S-H in carbonated Alite paste

Carbonation treatment is a promising option to enhance recycled concrete aggregate (RCA) quality and eventually improve concrete performance. This study investigated the multi-scale mechanical properties of calcium silicate hydrates (C-S-H) in a mature alite paste subjected to accelerated carbonation treatment by testing macro compressive strength, microhardness and nanoindentation. The results show that, carbonation treatment resulted in a heterogeneous distribution of carbonation products in the alite sample. Reinforcement of C-S-H by the randomly precipitated calcite and vaterite crystals prevailed over the nano-structural and compositional alteration of C-S-H induced by carbonation, leading to an increase of nano-indentation modulus at the edge of the sample. Also, the microhardness at the edge zone was markedly higher than that at the core of the carbonated sample. The carbonated peripheral zone with improved nano-scale modulus and microhardness was likely serving as a “hard shell”, contributing to the improved macro compressive strength. The new insights into the multi-scale mechanical properties of carbonated C-S-H contribute to further understanding of the enhanced properties of RCA after carbonation treatment.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effect of rice husk ash-derived activator on the structural build-up of alkali activated materials

Highlights: • Filtered and unfiltered sodium silicate solutions were synthesised from RHA. • The dissolution efficiency of RHA in NaOH solution was 76.3%. • RHA-derived activator showed a structural build-up comparable to the commercial activator in AAM pastes. • The undissolved residues in the unfiltered RHA-derived activator increased the yield stress. • Comparable compressive strength and early age gel formation were observed from both commercial and RHA-derived solutions. Waste-derived sodium silicates (SSs) were synthesised from rice husk ash (RHA) to produce alkali activated materials (AAMs) using fly ash and slag as precursors. The effects of these SSs on the structural build-up were investigated by monitoring the evolution of the viscoelasticity, ultrasonic pulse waves, setting time, and infrared spectra. Two types of RHA derived SSs (filtered SS and unfiltered SS) were prepared to investigate the effect of the undissolved residue on the hardening process. The derived SS contained a large portion of monomer silicate species. The results showed that the structural build-up mechanism was comparable between the AAMs activated by the filtered SS and a commercial SS. The unfiltered SS increased the yield stress of the paste by up to 10 times. However, the residues in the unfiltered SS had insignificant impacts on the gel formation and compressive strength when using identical SiO{sub 2}/Na{sub 2}O and Na{sub 2}O/binder ratios in the mix design.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Crack width control and mechanical properties of low carbon engineered cementitious composites (ECC)

Engineered Cementitious Composites (ECC) have superior properties with high tensile ductility and tight crack width compared to conventional concrete. The properties of ECC are significantly influenced by the material composition which can be tailored to enhance the sustainability of ECC. Towards this goal, recycled crumb rubber (CR) and silica fume (SF) were used to tailor the properties of a polypropylene-fiber reinforced ECC with a low carbon binder based on limestone calcined clay cement (LC3) in this study. Crumb rubber was found to be effective in enhancing strain-hardening performance and reducing the width of the multiple microcracks. However, a loss of compressive strength was accompanied by an increasing amount of CR. While silica fume or lower w/b ratio enhanced the compressive strength, the crack width of ECC increased at higher SF content or lower w/b. The underlying mechanisms of these trends were traced to the alteration of the matrix fracture toughness and fiber/matrix interfacial bond. Rubber particle bridging was found to contribute to crack width control. Finally, the combined use of the LC3 green binder and CR led to a lowering of the embodied and operational carbon footprint of ECC.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Carbon fiber design improvements based on economic models

Circular fiber geometries are predominant in commercial carbon fiber material systems, but the use of this fiber shape has numerous limitations. Circular geometries have continuous symmetry, which is helpful for various processing considerations, but also have the largest possible maximum diffusion thickness for a given fiber area. This characteristic means that circular carbon fibers always have the highest material processing cost and lowest production throughput compared to any other fiber shape with the same area and tow count. To quantify material cost and other benefits for non-circular carbon fiber geometries, process models for polyacrylonitrile based carbon fiber production are developed in relationship to the carbon fiber shape, size, and tow count. For a given fiber shape, precursor production costs are shown to favor maximizing fiber size while conversion costs are minimized by the smallest fiber size. These competing cost trends result in a numerically optimal fiber size for a given shape and tow count, while both cost components are decreased by increasing tow count. Cost–performance tradeoffs for three lobe fiber geometries are studied by supplementing the cost trends with a numerical failure model to predict compressive strength for discrete shape variants. The shape selection is shown to be more sensitive to variations in cost than compressive strength while suboptimal shape designs can improve manufacturing robustness and achievable fiber volume fractions. Finally, an optimal three lobe carbon fiber is identified that balances the set of considerations while reducing costs and embodied energy and increasing production throughput compared to a commercial carbon fiber.

Carbon fiber↗
DOE OSTI2020

Effects of heat treatment and build orientation on the evolution of $ϵ$ and $α'$ martensite and strength during compressive loading of additively manufactured 304L stainless steel

In this paper, the effect of heat-treatment and build orientation on martensitic phase transformation in additively manufactured (AM) 304L stainless steel is studied and compared with conventionally produced wrought material. The relationships between observed martensitic transformations and material microstructures and their effects on mechanical strength are established through experimental observations. In situ high-energy X-ray powder diffraction measurements were performed to monitor the evolution of $ϵ$ and $α'$ martensite during compressive loading of stainless steel. Electron backscatter diffraction (EBSD) was used to provide insight on initial grain morphology, crystallographic misorientation within grains, and crystallographic texture. Heat treatment alters the microstructure of AM samples creating different initial conditions. This difference in starting microstructure resulted in variability in martensitic transformation during compressive deformation. The rate of martensitic transformation decreased for AM samples treated with temperatures up to 1100°C, after which the AM microstructures recrystallized, resulting in increased rate of martensitic transformation for those samples treated at higher temperatures. It was also observed that aligning the axis of compression with the AM build direction resulted in a lower rate of strain-induced martensite formation as opposed to aligning the compression axis perpendicular to it. More favorable distribution of crystal orientations in the latter loading orientation promoted martensitic transformation. These and additional experimental observations from EBSD in terms of kernel average misorientation, mean grain orientation spread, and mean crystallite size reveal strong microstructural effects on strength of additively manufactured metallic materials.

304L stainless steel↗
DOE OSTI2022

Incorporating PCM-enabled thermal energy storage into 3D printable cementitious composites

This paper delineates the feasibility of incorporating microencapsulated phase change materials (mPCM) into 3D printable cementitious composite materials. A comprehensive experimental program was carried out to evaluate the impacts of mPCM on the printability, microstructures, mechanical and thermal properties of cementitious 3D printing ‘inks’. Results showed that the mPCM affected the printability of the cementitious ink material based on its physical properties (e.g., particle size) and volume loading – at lower volume loadings, mPCM increased the flowability of the cementitious ink material while leading to increased compressive strength and thermal conductivity for the hardened printed material. However, further increase in mPCM dosage led to a decrease in printability and, therefore, decrease in compressive strength and thermal conductivity as compared to the reference mixture. Here the results also showed that the inclusion of mPCM influence the printing parameters. In general, the inclusion of higher volume contents of mPCM necessitates a higher extrusion rate to achieve a desirable extrudability. Lastly, a thermal network model was formulated for 3D printed mPCM charged building components (e.g., wall). The study shows that microencapsulated PCM materials have good potential to be used in 3D printable cementitious mixtures for improving the thermal and energy performance of 3D printed buildings.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Microencapsulation of bio-based phase change materials with silica coated inorganic shell for thermal energy storage

This study investigates the use of cenospheres to encapsulate a low-cost, bio-based phase change material (PCM) derived from refined edible vegetable oil. Chemical etching was applied on the cenospheres to create holes through which melted PCM was loaded to produce a PCM microcapsule. Subsequently, a silica-based coating was applied to seal the perforations and prevent leakage of PCM from the microcapsule. Microstructural, chemical compatibility, thermal, and leakage properties of the produced silica coated PCM microcapsule (SCPCM) were assessed. No leakage was found for this new microcapsule, and higher thermal stability and conductivity were noted. Thermal decomposition of the PCM in SCPCM was delayed by about 16 degrees C attributable to the silica coating. Additionally, an enhanced compressive strength performance was achieved at 10 vol% of sand replacement with SCPCM. 20-30 vol% replacement of sand with cenosphere microcapsules seems to be the optimal range for reasonable compressive strength. The workability of the mortar incorporated with SCPCM decreased when the replacement level increased to more than 30 vol% due to the hydrophilic nature of the silica deposit. This study has demonstrated the potential of cenospheres as inorganic shell for PCMs and the potential for incorporation of SCPCM into construction materials for thermal energy storage (TES).

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2021

Influence of fine-scale B2 precipitation on dynamic compression and wear properties in hypo-eutectic Al0.5CoCrFeNi high-entropy alloy

The near equiatomic high-entropy alloys based on Al, Co, Cr, Fe, Ni have provided a novel microstructural template for alloy design. The face-centered cubic (FCC) matrix strengthened by body-centered cubic (BCC) based ordered B2 precipitates can be used to develop a new generation of precipitation strengthened alloys. The present study focuses on an Al0.5CoCrFeNi hypo-eutectic alloy consisting of an as-solidified FCC+B2 microstructure. Guided by solution thermodynamic modeling, this alloy has been isothermally aged for solid-state precipitation of a high fraction of fine-scale intragranular B2 particles. The dynamic compressive strength, hardness, and sliding wear response of the alloy as a function of B2 phase fraction is examined. The flow stress at 0.02% true strain increased from ~ 670 MPa to ~1350 (102%) MPa, the ultimate compressive strength increased from ~1160 MPa to 1500 MPa (20%), and the wear resistance increased more than 5 times with progressively increasing phase fraction of B2 precipitates.

Gwalani, Bharat↗
DOE OSTI2023

Fractionated and purified hybrid poplar lignins as a polyol replacement in rigid polyurethane/polyisocyanurate foams

This study introduces fractionated lignin as an innovative component in the formulation of rigid polyurethane/polyisocyanurate (PUR/PIR) foams. Low-density PUR/PIR rigid foams were prepared by replacing 80% of the petrochemical-based polyol with a hybrid poplar (HP) lignin, recovered via alkaline pretreatment, and also with a fraction of this lignin, isolated via the Aqueous Lignin Purification with Hot Agents (ALPHA) process. The as-recovered HP and ALPHA-fractionated HP lignins were characterized to determine hydroxyl content, molecular weight (Mw) distribution, and pH. Both lignin-based foams met minimum standard requirements in terms of closed cell content, compression strength, and thermal conductivity. Notably, the foams made with ALPHA-based lignin outperformed the as-recovered lignin-based foams in all measured foam properties. Moreover, the ALPHA-based foam had comparable performance to the control foam (without lignin) except for density and even surpassed the control foam in closed cell content and compressive strength. This investigation of the molecular properties of lignin suggests that significant reductions in lignin average molecular weight and polydispersity (PDI) can positively impact the properties of lignin-based rigid foams.

09 BIOMASS FUELS↗
DOE OSTI2024

ASSESSMENT OF HIGH-VOLUME HARVESTED FLY ASH BLENDS FOR USE IN PRECAST CONSTRUCTION

Declining supplies of fresh fly ashes in some regions have further driven the importance of using harvested fly ash as a supplementary cementitious material and thus replacement for more energy-intensive ordinary Portland cement (OPC). Higher replacement rates of OPC with fly ash in general has traditionally been limited in precast operations due to stringent early-age strength requirements necessitated by initial prestress and lifting/handling of hardened components – often well within 24 hours after fresh concrete placement. Therefore, a series of mix designs were developed, as part of a larger framework for reassessing high-volume fly ash (HVFA) use in the context of precast construction, to demonstrate the feasibility of using larger fractions of harvested fly ash in concrete formulations suitable for precast fabrication demands. More specifically, a target minimum 24-hour compressive strength of 24.1 MPa (3500 psi) was set, in accordance with conventional precast structural design checks, while increasing the fly ash content to 40% replacement of OPC – at least a 15% increase above the traditional limit of 25%. The effect of using more sustainable Type IL cement in contrast to conventional Type III Portland cement (the traditional standard for precast use) – both in conjunction with HVFA use – was also examined. Early-age mechanical properties including compressive strength, modulus of rupture, and modulus of elasticity were evaluated within the aforementioned early-age window. Lastly, corresponding design equations were then reassessed for their applicability with respect to the high-early strength HVFA mixes examined herein.

Gombeda, Matthew J.↗
DOE OSTI2024

Additive manufacturing of AISI M2 tool steel by binder jetting (BJ): Investigation of microstructural and mechanical properties

The presented research demonstrates for the first time the successful processing of AISI M2 tool steel by binder jetting, a promising additive manufacturing technique capable of producing complex shapes with minimal residual stresses and isotropic properties. The optimal printing parameters were explored by varying processing parameters such as the binder saturation (45 %–105 %), binder set time (0 to 10 s), targeted bed temperature (50–60 °C), oscillator (2600–2750 rpm), recoater (20–28 mm/s), and roller speeds (200–300 rpm). Microstructural characterization and evaluation of mechanical properties of binder jetted parts were performed using x-ray diffraction (XRD), scanning electron microscopy (SEM), and energy dispersive spectroscopy (EDS) to study their chemical composition, powder morphology, microstructure, carbide morphologies, relative density, hardness, compressive strength, and ductility. Two powder sizes (5 and 10 μm) were used, and sintering was performed at varying temperatures (1270, 1280, and 1300 °C) and durations (60 and 120 min), followed by a furnace, air, and water cooling. An optimum hardness of ~970 HV was obtained when parts were sintered at 1270 °C for 60 min, followed by water quenching. Impressive compressive strength of ~ 3580 MPa was observed in the sample sintered at 1280 °C for 60 min duration, followed by air cooling. Furnace-cooled parts showed the highest density of ~95 %, whereas the relative density of air- and water-cooled parts varied between ~91 to 93.50 %, respectively. The microstructure of sintered samples revealed the formation of M 6 C stable carbide, M 2 C metastable carbide, MC as a secondary carbide, and a-Fe matrix, which contributed to the observed increase in mechanical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2023

ANS MiNES 2023 Poster

The dynamic mechanical properties of four varieties of high purity graphite as well as the depth of penetration (DoP) of a small-scale shaped charge into these grades was experimentally determined. The grades chosen were PCEA, NBG-18, and NBG-25. These grades provide a wide range of physical properties: in density from 1.80 – 1.85 g/cc, in maximum particle size from 10s to 1000s of µm, and in porosity from 18% to 20%. The quasistatic and dynamic compressive strengths of each grade were determined and correlated to their physical properties. The split Hopkinson pressure bar experiments showed both the dynamic strength and dominant shear failure mechanisms. A small scale shaped charge was used to compare the resistance of graphite to hypervelocity jet impacts: the Teledyne RP-4. The RP-4 has a 1.01” outer diameter and 3.44 g of RDX with an RP-80 booster (86 mg PETN + 123 mg RDX). A select number of samples were analyzed using X-Ray Computed Tomography (XCT), allowing for the full characterization of the undisturbed wound channel. A selection of other samples were physically sectioned and wound channels mapped from the sections. In addition to DoP, the wound geometry was characterized in terms of total volume and diameter at different depths. The wound channel characteristics for each grade were correlated to the compressive strengths and physical properties. In several of the test samples, the wound channel diameter was smaller than the diameter of the shaped charge slug just behind where the slug had penetrated the sample. These results indicated that the wound geometry was dependent on the compressive hysteresis behavior of graphite.

36 MATERIALS SCIENCE↗
DOE OSTI2020

The Complicated Link Between Material Properties and Microfracture Density for an Underground Explosion in Granite

Geophysical techniques are often implemented as quick and inexpensive ways to locate and characterize fractures in the subsurface, which is important for a number of geoscience fields. Seismic velocities are the most widely used proxies for identification of fractures, but the correlation is not always well-defined. In this study we present material property data: unconfined compressive strength (UCS), bulk density (ρ), Young's modulus (E), Poisson's ratio (ν), P wave velocity (V p ), and S wave velocity (V s ), in conjunction with microfracture densities measured on samples of granite collected before and after underground chemical explosions. Results indicate the relationship between fractures and material properties is complex, even in this single-lithology environment. We interpret that this complexity arises from varying fracture mechanisms (e.g. dilation-inducing fractures vs compression-inducing fractures) in different parts of the core, due to differences in stress conditions. Additional complexity may result from chemical interactions between the fresh fractures and the fluids in the area. Water content appears to have a significant, if not dominant, role in the unconfined compressive strength (UCS) of the samples. We suggest caution when using elastic property measurements as a proxy for fracturing in areas of explosion-induced damage, or in other areas where a variety of mechanisms induce fracturing.

58 GEOSCIENCES↗
DOE OSTI2021

Qualification of 3-D Printed Mortar With Electrical Conductivity Measurements

Additive manufacturing (AM) or 3D printing of concrete allows for construction of arbitrary shape structures without a mold. Since reproducibility of 3D printed concrete is lower than that of conventional fabrication, each 3D printed structure should be monitored for proper curing. Conventional qualification of concrete is based on several tests, including destructive compressive strength measurements. Because a structure is 3-D printed layer-by-layer, the surfaces of AM concrete structures have significant surface roughness. This limits the applicability of conventional nondestructive testing methods. We investigated qualification of 3D printed mortar by monitoring curing with nondestructive electrical conductivity measurements. Bulk resistance of concrete was extracted from electrochemical impedance spectroscopy (EIS measurements made using custom flexible self-adhesive electrodes, which contour to rough surfaces. We show that bulk resistivity of concrete increases linearly with time. This allows for developing a calibration curve for compressive strength lookup from nondestructive electrical conductivity measurements. Conductivity measurements also allow for estimation of formation factor, which is an indicator of mortar permeability.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Binder-jetted AISI M2 tool steel during hot isostatic pressing: Densification and carbide transformation

Binder jetting (BJ) enables fabrication of complex components from high-alloy steels such as AISI M2; however, residual porosity after sintering limits mechanical performance. This study investigates the coupled effects of binder chemistry, sintering conditions, cooling rate, and subsequent hot isostatic pressing (HIP) on densification, microstructure, and mechanical response in binder-jetted M2 tool steel. HIP increased relative density from ∼93 to 95% to >99% and improved compressive strength by ∼40-70%. Densification was governed by initial pore morphology, where closed porosity was effectively eliminated, while interconnected porosity limited full consolidation. Microstructural analysis (XRD, EBSD, SEM) shows that HIP promotes dissolution of metastable carbides and redistribution of alloying elements (W, Mo, V), transforming heterogeneous carbide networks into finer and more uniformly distributed M 2 C, MC, and M 6 C phases through diffusion-assisted homogenization. Among the investigated conditions, the FluidFuse binder combined with sintering at 1270 °C for 60 min and furnace cooling produced the most balanced response, achieving ∼99.7% density, ∼855 HV hardness, ∼4130 MPa compressive strength, and ∼24% strain. In contrast, higher sintering temperatures promoted carbide coarsening, reducing ductility despite high density. HIP reduces microstructural heterogeneity and drives the system toward a near-equilibrium state with reduced sensitivity to prior processing history. A comparative assessment with conventional and additive manufacturing routes (LPBF, DED, EBM, FFF) shows that the BJ-HIP approach achieves competitive densification and mechanical performance. These findings provide a mechanistic basis for controlling densification and microstructure in high-alloy steels processed via BJAM.

AISI M2 tool steel↗