Fuels for turbojets and ramjets.
Combustion properties of high energy fuels used in turbojet and ramjet propulsion systems
RAMJET ENGINE↗
SEARCH · Engineering Papers
Results for “COMBUSTION PROPERTIES”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Energetic Performance of Optically Activated Aluminum/Graphene Oxide Composites
Optical ignition of solid energetic materials, which can rapidly release heat, gas, and thrust, is still challenging due to the limited light absorption and high ignition energy of typical energetic materials ( e.g., aluminum, Al). Here, we demonstrated that the optical ignition and combustion properties of micron-sized Al particles were greatly enhanced by adding only 20 wt % of graphene oxide (GO). These enhancements are attributed to the optically activated disproportionation and oxidation reactions of GO, which release heat to initiate the oxidization of Al by air and generate gaseous products to reduce the agglomeration of the composites and promote the pressure rise during combustion. More importantly, compared to conventional additives such as metal oxides nanoparticles ( e.g., WO 3 and Bi 2 O 3 ), GO has much lower density and therefore could improve energetic properties without sacrificing Al content. Finally, the results from Xe flash ignition and laser-based excitation experiments demonstrate that GO is an efficient additive to improve the energetic performance of micron-sized Al particles, enabling micron-sized Al to be ignited by optical activation and promoting the combustion of Al in air.
36 MATERIALS SCIENCE↗
Fuel-rich catalytic combustion of a high density fuel
Fuel-rich catalytic combustion (ER is greater than 4) of the high density fuel exo-tetrahydrocyclopentadiene (JP-10) was studied over the equivalence ratio range 5.0 to 7.6, which yielded combustion temperatures of 1220 to 1120 K. The process produced soot-free gaseous products similar to those obtained with iso-octane and jet-A in previous studies. The measured combustion temperature agreed well with that calculated assuming soot was not a combustion product. The process raised the effective hydrogen/carbon (H/C) ratio from 1.6 to over 2.0, thus significantly improving the combustion properties of the fuel. At an equivalence ratio near 5.0, about 80 percent of the initial fuel carbon was in light gaseous products and about 20 percent in larger condensable molecules. Fuel-rich catalytic combustion has now been studied for three fuels with H/C ratios of 2.25 (iso-octane), 1.92 (jet-A), and 1.6 (JP-10). A comparison of the product distribution of these fuels shows that, in general, the measured concentrations of the combustion products were monotonic functions of the H/C ratio with the exception of hydrogen and ethylene. In these cases, data for JP-10 fell between iso-octane and jet-A rather than beyond jet-A. It is suggested that the ring cross-linking structure of JP-10 may be responsible for this behavior. All the fuels studied showed that the largest amounts of small hydrocarbon molecules and the smallest amounts of large condensable molecules occurred at the lower equivalence ratios. This corresponds to the highest combustion temperatures used in these studies. Although higher temperatures may improve this mix, the temperature is limited. First, the life of the present catalyst would be greatly shortened when operated at temperatures of 1300 K or greater. Second, fuel-rich catalytic combustion does not produce soot because the combustion temperatures used in the experiments were well below the threshold temperature (1350 K) for the formation of soot. Increasing the temperature above this value would remove the soot-free nature of the process. Since all the fuels studied show a similar breakdown of the primary fuel into smaller molecular combustion products, this technique can be applied to all hydrocarbon fuels.
Brabbs, Theodore A.↗
Fabrication, oxidation, and combustion of nanoscale magnesium diboride and tetraboride
The difficult ignition and low combustion efficiency of boron particles decrease the performance of boron-loaded, fuel-rich propellants for solid fuel ramjets and ducted rockets. One approach to solving this problem involves the use of magnesium diboride (MgB 2 ), which ignites easier than boron. Magnesium tetraboride (MgB 4 ) offers greater energy density owing to its higher boron content. However, the effect of B/Mg ratio on the ignition and combustion is unknown. Additionally, while nanoscale MgB₂ particles and quasi-2D structures are promising energetic additives, the oxidation and combustion properties of nanoscale MgB₄ have not been explored. To address these knowledge gaps, the present work included synthesis and high-energy ball milling of MgB 2 and MgB 4 powders, thermogravimetric analysis (TGA) of their oxidation, and combustion experiments with thin layers of the obtained powders. Comparison of two synthesis routes (a solid-state reaction in a tube furnace and combustion synthesis) has shown that the former is the superior method for producing magnesium borides. TGA has revealed that oxidation of both MgB 2 and MgB 4 results in a high conversion into the oxides (88–91 %), far exceeding the low conversion of boron (62.5 %). MgB 4 begins to oxidize rapidly at a much lower temperature (∼900 °C) than MgB 2 (∼1200 °C). The burning rates of milled MgB 2 and MgB 4 are about eight and five times, respectively, faster than that of submicron boron. Magnesium borides exhibit a stable, sustained boron flame, needed for high combustion efficiency, whereas physical Mg/B mixtures undergo Mg-driven "flash" combustion.
Boron↗
Fabrication, oxidation, and combustion of nanoscale magnesium diboride and tetraboride
The difficult ignition of boron decreases the combustion efficiency of boron-loaded, fuel-rich propellants. One approach to solving this problem involves the use of magnesium diboride (MgB2), which ignites easier than boron. Magnesium tetraboride (MgB4) offers greater energy density owing to its higher boron content. However, the effect of B/Mg ratio on the ignition and combustion is unknown. Additionally, while nanoscale MgB₂ particles and quasi-2D structures were recently recognized as promising energetic additives, the oxidation and combustion properties of nanoscale MgB₄ have not been explored. The objectives of the present work included synthesis, purification, and high-energy ball milling of MgB2 and MgB4 powders as well as investigation of their thermal decomposition, oxidation, and combustion. The MgB2 and MgB4 powders were fabricated by combustion synthesis in the chemical oven mode and by heating Mg/B mixtures in a tube furnace. The latter method was superior in the synthesis of MgB4. Oxide impurities in the synthesized powders were removed by acid leaching. Nanoscale powders were obtained by high-energy ball milling. Thermal decomposition and oxidation of the obtained MgB₂ and MgB₄ powders were investigated by conducting non-isothermal thermogravimetric analysis (TGA) at temperatures up to 1550 °C in argon and oxygen flows. Combustion of B, MgB₂, and MgB₄ powders with oxygen at atmospheric pressure was studied in a windowed chamber using laser ignition and high-speed video recording. The TGA has shown multi-step decomposition of both magnesium borides in an argon environment. The maximum oxidation rate of MgB4 in oxygen was observed at a much lower temperature than in the case of MgB2. In the combustion experiments, both magnesium borides burned much faster than submicron boron. Ball milling of the borides further increased their burning rates. It has been concluded that nanoscale magnesium tetraboride is a promising ingredient for fuel-rich propellants owing to its high energy density, efficient oxidation, and rapid combustion.
Molina, Andre [The University of Texas at El Paso]↗
Investigation of spray characteristics for flashing injection of fuels containing dissolved air and superheated fuels
The flow, atomization and spreading of flashing injector flowing liquids containing dissolved gases (jet/air) as well as superheated liquids (Freon II) were considered. The use of a two stage expansion process separated by an expansion chamber, ws found to be beneficial for flashing injection particularly for dissolved gas systems. Both locally homogeneous and separated flow models provided good predictions of injector flow properties. Conventional correlations for drop sizes from pressure atomized and airblast injectors were successfully modified, using the separated flow model to prescribe injector exit conditions, to correlate drop size measurements. Additional experimental results are provided for spray angle and combustion properties of sprays from flashing injectors.
Solomon, A. S. P.↗
Fuel properties to enable lifted-flame combustion
The Fuel Properties to Enable Lifted-Flame Combustion project responded directly to solicitation DE-FOA-0000239 AOI 1A, Fuels and Lubricants for Advanced Combustion Regimes. This subtopic was intended to encompass clean and highly-efficient, liquid-fueled combustion engines to achieve extremely low engine-out nitrogen oxides (NOx) and particulate matter (PM) as a target and similar efficiency as state-of-the-art direct injection diesel engines. The intent of this project was to identify how fuel properties can be used to achieve controllable Leaner Lifted Flame Combustion (LLFC) with low NOx and PM emissions. Specifically, this project was expected to identify and test key fuel properties to enable LLFC and their compatibility with current fuel systems and to enhance combustion models to capture the effect of fuel properties on advanced combustion. Successful demonstration of LLFC may reduce the need for after treatment devices, thereby reducing costs and improving thermal efficiency. The project team consisted of key technical personnel from Ford Motor Company (FMC), the University of Wisconsin-Madison (UW), Sandia National Laboratories (SNL) and Lawrence Livermore National Laboratories (LLNL). Each partner had key roles in achieving project objectives. FMC investigated fuel properties relating to LLFC and sooting tendency. Together, FMC and UW developed and integrated 3D combustion models to capture fuel property combustion effects. FMC used these modeling results to develop a combustion system and define fuel properties to support a single-cylinder demonstration of fuel-enabled LLFC. UW investigated modeling the flame characteristics and emissions behavior of different fuels, including those with different cetane number and oxygen content. SNL led spray combustion experiments to quantify the effect of key fuel properties on combustion characteristics critical for LLFC, as well as single cylinder optical engine experiments to improve fundamental understanding of flame lift-off, generate model validation data, and demonstrate LLFC concurrent with FMC efforts. Additionally, LLNL was added to the project during the second year to develop a detailed kinetic mechanism for a key oxygenate to support CFD modeling. Successful completion of this project allowed the team to enhance fundamental understanding of LLFC, improve the state of current combustion models and increase understanding of desired fuel properties. This knowledge also improves our knowledge of how cost effective and environmentally friendly renewable fuels can assist in helping meet future emission and greenhouse gas regulations.
Kurtz, Eric↗
EPS (Electric Particulate Suspension) Microgravity Technology Provides NASA with New Tools
The Electric Particulate Suspension is a fire safety ignition test system being developed at Iowa State University with NASA support for evaluating combustion properties of powders, powder-gas mixtures, and pure gases in microgravity and gravitational atmospheres (quenching distance, ignition energy, flammability limits). A separate application is the use of EPS technology to control heat transfer in vacuum and space environment enclosures. In combustion testing, ignitable powders (aluminum, magnesium) are introduced in the EPS test cell and ignited by spark, while the addition of inert particles act as quenching media. As a combustion research tool, the EPS method has potential as a benchmark design for quenching powder flames that would provide NASA with a new fire safety standard for powder ignition testing. The EPS method also supports combustion modeling by providing accurate measurement of flame-quenching distance as an important parameter in laminar flame theory since it is closely related to characteristic flame thickness and flame structure. In heat transfer applications, inert powder suspensions (copper, steel) driven by electric fields regulate heat flow between adjacent surfaces enclosures both in vacuum (or gas) and microgravity. This simple E-field control can be particularly useful in space environments where physical separation is a requirement between heat exchange surfaces.
Colver, Gerald M.↗
Camphorane as a Renewable Diesel Blendstock Produced by Cyclodimerization of Myrcene
Camphorene was synthesized by the thermal Diels–Alder cyclodimerization of myrcene and subsequently hydrogenated to produce camphorane. On the basis of common fuel metrics (density, lower heating value, cetane, and viscosity) the prepared camphorane fuel exhibits appropriate physicochemical properties for its implementation in compression ignition engines. The high viscosity of camphorane necessitates its blending with petroleum diesel, which offers a final fuel within the ASTM specification for diesel. Soot production measurements of camphorane and its blends with diesel demonstrate a potential to significantly reduce soot emissions. The physicochemical and combustion properties of camphorane are further compared to those of other terpene biofuels along with biodiesel.
09 BIOMASS FUELS↗
Ab initio pressure-dependent reaction kinetics of methyl propanoate radicals
The unimolecular dissociation and isomerization kinetics of the three methyl propanoate (MP) radicals, CH 3 CH 2 C(=O)O$\dot{C}$H 2 (MP-m), CH 3 $\dot{C}$HC(=O)OCH 3 (MP-α), and $\dot{C}$H 2 CH 2 C(=O)OCH 3 (MP-β), are theoretically investigated using high-level ab initio methods and the Rice–Ramsperger–Kassel–Marcus (RRKM)/master equation (ME) theory. Stationary-point energies are obtained using the coupled cluster singles and doubles with perturbative triples correction (CCSD(T)), multi-reference singles and doubles configuration interaction (MRSDCI) with the Davidson-Silver (DS) correction, and multi-reference averaged coupled pair functional (MRACPF2) theories. The isomerization barriers between the three radicals are predicted to be generally lower than the corresponding bond dissociation channels, leading to a strongly coupled reaction system in subsequent kinetics studies. The phenomenological temperature- and pressure-dependent rate coefficients are computed using the RRKM/ME theory over a temperature range of 500 to 2000 K and at a pressure range of 0.01 atm to the high-pressure limit, which are then fitted to modified Arrhenius expressions. The β-scission rate coefficients of MP-α to CH 3 CHC(=O) and CH 3 $\dot{O}$ are predicted to be the smallest because of its highest activation energy among all studied unimolecular reactions channels. Analysis of branching fractions shows that both MP-m and MP-α radicals mainly decompose to the bimolecular products CH 3 CH 2 $\dot{C}$(=O) and H 2 CO, whereas the MP-β radical primarily decomposes via cleavage of a C–C bond to form C 2 H 4 and CH 3 O$\dot{C}$(=O). The isomerization channels dominate at low temperatures, the branching fractions of which decrease with increasing temperature and become very minor at about 2000 K. Our accurate rate coefficients and branching fractions help to illuminate the unique combustion properties of MP.
09 BIOMASS FUELS↗
A numerical study on the sooting tendencies of bio-derived fuels for spark-ignition engines
While more efficient vehicles have been developed over the decades, their performance is limited by the properties of existing fuels. In response, the Co-Optimization of Fuels and Engines Initiative (Co-Optima) under the U.S. Department of Energy (DOE) has developed a rigorous screening approach to identify the most promising biomass-derived blendstocks that are suitable for advanced spark-ignition (SI) engines. A detailed kinetic model has also been developed to predict the combustion properties of the selected blendstocks. This kinetic model has been designed mainly targeting ignition and flame propagation properties, and it has not previously been validated for soot formation. In this work, we numerically predicted the sooting tendency of 20 Co-Optima SI blendstocks using the Co-Optima kinetic model. The sooting tendencies are determined quantitatively using the Yield Sooting Index (YSI) methodology. As shown in Fig. 1, the predicted YSIs show good agreement with measurements, except for 2,5-dimethylfuran. We also quantify the sensitivity of the YSI predictions to aromatic growth reactions and fuel decomposition reactions of the test fuels. It is found that PAH growth reactions have little impact on YSIs for all 20 fuels under investigation. On the other hand, fuel decomposition reactions have a significant influence on the YSI of 2,5-dimethylfuran. Perturbing their reaction rates by a factor of two is shown to lead to 11 % YSI prediction uncertainty.
09 BIOMASS FUELS↗
Fiber Supported Droplet Combustion-2 (FSDC-2)
Experimental results for the burning characteristics of fiber supported, liquid droplets in ambient Shuttle cabin air (21% oxygen, 1 bar pressure) were obtained from the Glove Box Facility aboard the STS-94/MSL-1 mission using the Fiber Supported Droplet Combustion - 2 (FSDC-2) apparatus. The combustion of individual droplets of methanol/water mixtures, ethanol, ethanol/water azeotrope, n-heptane, n-decane, and n-heptane/n-hexadecane mixtures were studied in quiescent air. The effects of low velocity, laminar gas phase forced convection on the combustion of individual droplets of n-heptane and n-decane were investigated and interactions of two droplet-arrays of n-heptane and n-decane droplets were also studied with and without gas phase convective flow. Initial diameters ranging from about 2mm to over 6mm were burned on 80-100 micron silicon fibers. In addition to phenomenological observations, quantitative data were obtained in the form of backlit images of the burning droplets, overall flame images, and radiometric combustion emission measurements as a function of the burning time in each experiment. In all, 124 of the 129 attempted experiments (or about twice the number of experiments originally planned for the STS-94/MSL-1 mission) were conducted successfully. The experimental results contribute new observations on the combustion properties of pure alkanes, binary alkane mixtures, and simple alcohols for droplet sizes not studied previously, including measurements on individual droplets and two-droplet arrays, inclusive of the effects of forced gas phase convection. New phenomena characterized experimentally for the first time include radiative extinction of droplet burning for alkanes and the "twin effect" which occurs as a result of interactions during the combustion of two-droplet arrays. Numerical modeling of isolated droplet combustion phenomenon has been conducted for methanol/water mixtures, n-heptane, and n-heptane/n-hexadecane mixtures, and results compare quantitatively with those found experimentally for methanol/water mixtures. Initial computational results qualitatively predict experimental results obtained for isolated n-heptane and n-heptane/n-hexadecane droplet combustion, although the effects of sooting are not yet included in the modeling work. Numerical modeling of ethanol and ethanol/water droplet burning is under development. Considerable data remain to be fully analyzed and will provide a large database for comparisons with further numerical and analytical modeling and development of future free droplet experiments aboard space platforms.
Colantonio, Renato↗
Technical Proposal for Loading 3000 Gallon Crude Oil Samples from Field Terminal to Sandia Pressurized Tanker to Support US DOE/DOT Crude Oil Characterization Research Study
Sandia National Laboratories is seeking access to crude oil samples for a research project evaluating crude oil combustion properties in large-scale tests at Sandia National Laboratories in Albuquerque, NM. Samples must be collected from a source location and transported to Albuquerque in a tanker that complies with all applicable regulations for transportation of crude oil over public roadways. Moreover, the samples must not gain or lose any components, to include dissolved gases, from the point of loading through the time of combustion at the Sandia testing facility. In order to achieve this, Sandia designed and is currently procuring a custom tanker that utilizes water displacement in order to achieve these performance requirements. The water displacement procedure is modeled after the GPA 2174 standard “Obtaining Liquid Hydrocarbons Samples for Analysis by Gas Chromatography” (GPA 2014) that is used routinely by crude oil analytical laboratories for capturing and testing condensates and “live” crude oils, though it is practiced at the liter scale in most applications. The Sandia testing requires 3,000 gallons of crude. As such, the water displacement method will be upscaled and implemented in a custom tanker. This report describes the loading process for acquiring a ~3,000 gallon crude oil sample from commercial process piping containing single phase liquid crude oil at nominally 50-100 psig. This document contains a general description of the process (Section 2), detailed loading procedure (Section 3) and associated oil testing protocols (Section 4).
02 PETROLEUM↗
Fabrication and characterization of nanoscale magnesium diboride and tetraboride for propulsion and hydrogen storage applications
Abstract: Boron-loaded propellants have the potential to dramatically increase the performance of solid fuel ramjets, ducted rockets, and hybrid rocket engines. However, difficult ignition of boron decreases the combustion efficiency of these propellants. One approach to solving this problem involves the use of magnesium diboride, MgB2, which ignites easier than boron. Magnesium tetraboride, MgB4, potentially offers greater energetic performance as B has a higher energy density than Mg. However, the effect of the higher boron/metal ratio on the ignition and combustion is unclear. Nanoscale MgB2 particles and quasi 2D structures are promising propellant ingredients, but the oxidation and combustion properties of nanoscale MgB4 remain unknown. Nanoscale magnesium borides are also of interest as precursors for the synthesis of magnesium borohydride, Mg(BH4)2, a promising hydrogen storage material, but hydrogenation of MgB4 has not been studied yet. The objectives of the present work included synthesis, purification, and high-energy ball milling of MgB2 and MgB4 powders as well as investigation of their hydrogen uptake, thermal decomposition, oxidation, and combustion. The powders were fabricated by combustion synthesis and by heating in a tube furnace. The latter method was superior in the synthesis of MgB4. Oxide impurities in the synthesized powders were removed by acid leaching. Nanoscale powders were obtained by ball-mill exfoliation. The hydrogen intake of the obtained magnesium borides was examined at 700 bar and 300 ℃ and did not reveal any advantage of MgB4 over MgB2. Their thermal decomposition and oxidation were investigated with thermogravimetric analysis (TGA), while their combustion was studied using laser ignition and high-speed video recording. TGA has confirmed prior observations of multistep decomposition of magnesium borides, where each step involves formation of a boride with a higher B/Mg ratio and evaporation of formed magnesium. The oxidation rates of the borides are much higher than that of boron at temperatures over 1200 °C for MgB2 and over 900 °C for MgB4. The burning rates of non-milled MgB₂ and MgB₄ powders were much higher than for the used submicron boron. Milling the MgB₂ and MgB₄ powders further increased their burning rates. The milled MgB4 burned 7.5 times faster than submicron boron.
Combustion of metals, Solid fuels, Propellants, Hy↗
Critical fuel property evaluation for potential gasoline and diesel biofuel blendstocks with low sample volume availability
Not Available
Polikarpov, Evgueni (ORCID:000000028089810X)↗
Effects of alpha-zirconium phosphate on thermal degradation and flame retardancy of transparent intumescent fire protective coating
Graphical abstract: - Highlights: • A transparent intumescent fire protective coating was obtained by UV-cured technology. • OZrP could enhance the thermal stability and anti-oxidation of the coating. • OZrP could reduce the combustion properties of the coatings. - Abstract: Organophilic alpha-zirconium phosphate (OZrP) was used to improve the thermal and fire retardant behaviors of the phenyl di(acryloyloxyethyl)phosphate (PDHA)-triglycidyl isocyanurate acrylate (TGICA)-2-phenoxyethyl acrylate (PHEA) (PDHA-TGICA-PHEA) coating. The morphology of nanocomposite coating was characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). The effect of OZrP on the flame retardancy, thermal stability, fireproofing time and char formation of the coatings was investigated by microscale combustion calorimeter (MCC), thermogravimetric analysis (TGA), X-ray photoelectron spectroscopy (XPS), laser Raman spectroscopy (LRS) and scanning electric microscope (SEM). The results showed that by adding OZrP, the peak heat release rate and total heat of combustion were significantly reduced. The highest improvement was achieved with 0.5 wt% OZrP. XPS analysis indicated that the performance of anti-oxidation of the coating was improved with the addition of OZrP, and SEM images showed that a good synergistic effect was obtained through a ceramic-like layer produced by OZrP covered on the surface of char.
36 MATERIALS SCIENCE↗
Macroscale properties and atomic-scale mechanisms of ash removal in low-temperature hydrothermal carbonization
Biogenic ash is a significant impediment to the utilization of agricultural residues in biofuel production. Such challenge can be addressed by various treatments, as demonstrated in this study on the experimental and computational mechanisms involved in the hydrothermal treatment (HT) of wheat straw. A combination of classical (all-atom) molecular dynamics simulations of cellulose carrying silica and calcium species, along with first principles quantum chemical calculations, indicates the dissociation of inorganics from the cellulose with increased HT temperature. Here, this observation is confirmed by experimental evidence of effective ash removal by HT, showing at least 50% removal of sulfur, chlorine, potassium, and calcium, and 12.5% of silica, leading to a reduced total ash content (from 6.7% to 4.2%).Changes in structural features upon HT, such as surface cellular structure and porosity, were revealed, accompanied by an increased specific surface area (from 1.17 to 6.34 m 2 /g). Our simulations suggest that silica binds tightly to the hydrophobic face of cellulose at room temperature, but HT significantly reduces the binding free energy of association with both hydrophobic and hydrophilic surfaces. Most significantly, ash removal leads to an increased calorific value, rising from approximately 16 MJ/kg to about 19 MJ/kg, along with improved thermal behavior. The improved integration combustion index parameter S indicates that the combustion properties improve with ash removal efficiency. The proposed atomic-level mechanism for the observed removal of inorganics during mild HT underscores the potential of such treatment in producing energy-dense wheat straw, a widely available agricultural residue.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Elucidating the differences in oxidation of high-performance α- and β- diisobutylene biofuels via Synchrotron photoionization mass spectrometry
Abstract Biofuels are a promising ecologically viable and renewable alternative to petroleum fuels, with the potential to reduce net greenhouse gas emissions. However, biomass sourced fuels are often produced as blends of hydrocarbons and their oxygenates. Such blending complicates the implementation of these fuels in combustion applications. Variations in a biofuel’s composition will dictate combustion properties such as auto ignition temperature, reaction delay time, and reaction pathways. A handful of novel drop-in replacement biofuels for conventional transportation fuels have recently been down selected from a list of over 10,000 potential candidates as part of the U.S. Department of Energy’s (DOE) Co-Optimization of Fuels and Engines (Co-Optima) initiative. Diisobutylene (DIB) is one such high-performing hydrocarbon which can readily be produced from the dehydration and dimerization of isobutanol, produced from the fermentation of biomass-derived sugars. The two most common isomers realized, from this process, are 2,4,4-trimethyl-1-pentene (α-DIB) and 2,4,4-trimethyl-2-pentene (β-DIB). Due to a difference in olefinic bond location, the α- and β- isomer exhibit dramatically different ignition temperatures at constant pressure and equivalence ratio. This may be attributed to different fragmentation pathways enabled by allylic versus vinylic carbons. For optimal implementation of these biofuel candidates, explicit identification of the intermediates formed during the combustion of each of the isomers is needed. To investigate the combustion pathways of these molecules, tunable vacuum ultraviolet (VUV) light (in the range 8.1–11.0 eV) available at the Lawrence Berkeley National Laboratory’s Advanced Light Source (ALS) has been used in conjunction with a jet stirred reactor (JSR) and time-of-flight mass spectrometry to probe intermediates formed. Relative intensity curves for intermediate mass fragments produced during this process were obtained. Several important unique intermediates were identified at the lowest observable combustion temperature with static pressure of 93,325 Pa and for 1.5 s residence time. As this relatively short residence time is just after ignition, this study is targeted at the fuels’ ignition events. Ignition characteristics for both isomers were found to be strongly dependent on the kinetics of C 4 and C 7 fragment production and decomposition, with the tert-butyl radical as a key intermediate species. However, the ignition of α-DIB exhibited larger concentrations of C 4 compounds over C 7 , while the reverse was true for β-DIB. These identified species will allow for enhanced engineering modeling of fuel blending and engine design.
09 BIOMASS FUELS↗