SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Flight test of l0-foot nominal-diameter disk-gap band parachute to determine deployment and inflation, opening shock loads, drag efficiency, and stability characteristics
On July 4, 1997, the Mars Pathfinder (MPF) mission successfully landed on Mars. The entry, descent, and landing (EDL) scenario employed the use of a Disk-Gap-Band parachute design to decelerate the Lander. Flight reconstruction of the entry using MPF flight accelerometer data revealed that the MPF parachute decelerated faster than predicted. In the summer of 2003, the Mars Exploration Rover (MER) mission will send two Landers to the surface of Mars arriving in January 2004. The MER mission utilizes a similar EDL scenario and parachute design as that employed by MPF. As a result, characterizing the degree of underperformance of the MPF parachute system is critical for the MER EDL trajectory design. This paper provides an overview of the methodology utilized to estimate the MPF parachute drag coefficient as experienced on Mars.
The Advanced Supersonic Parachute Inflation Research and Experiments (ASPIRE) project will investigate the supersonic deployment, inflation, and aerodynamics of Disk- Gap-Band (DGB) parachutes in the wake of a slender body. The parachutes will be full-scale versions of the DGBs used by the Mars Science Laboratory in 2012 and planned for NASA’s Mars 2020 project and will be delivered to targeted deployment conditions representative of flight at Mars by sounding rockets launched out of NASA’s Wallops Flight Facility. The parachutes will be tested in the wake of a slender payload whose diameter is approximately a sixth that of entry capsules used for Mars missions. Models of the deployment, inflation, and aerodynamic performance of the parachutes are necessary to design key aspects of the experiment, including: determining the expected loads and applicable margins on the parachute and payload; guiding sensor selection and placement; evaluating the vehicle trajectory for targeting, range safety, and recovery operations. In addition, knowledge of the differences in the behavior of the parachutes in the wake of slender and blunt bodies is required in order to interpret the results of the sounding rocket experiment and determine how they relate to expected performance behind blunt bodies at Mars. However, modeling the performance of a supersonic DGB in the wake of a slender body is challenging due to the scarcity of historical test data and modeling precedents. This paper describes the models of the aerodynamic performance of DGBs in supersonic slender-body wakes being developed for the ASPIRE sounding rocket test campaign. Development of these models is based on the four available flight tests of DGBs deployed in supersonic slender-body wakes as well as on data from past flight and wind-tunnel experiments of DGBs deployed in the wake of blunt bodies, on the reconstructed at-Mars DGB performance during past missions, and on computational fluid dynamics simulations. Simulations of the wakes of blunt and slender bodies in supersonic flow have been conducted in order to investigate the differences in the flowfields encountered by parachutes deployed in both wake types. The simulations have allowed the project to investigate the fundamental differences between the sounding rocket tests and the flight of a DGB during a Mars mission and to assess the limitations of the sounding rocket test architecture for evaluating flight performance at Mars.
A solid-state radiation detector includes a pattern of conductive metal on a zinc oxide substrate. The pattern provides an arrangement of interdigitated electrode fingers. The wide band gap substrate is sensitive to UV light, which can cause a conductivity change in the substrate. The electrode fingers are configured to sense a difference in substrate conductivity resulting from UV light. The detector has a fast response time, which enables it to detect Cherenkov light. The compact detector provides savings on size, weight, and required power. Thus, the solid-state detector can be used to replace photomultiplier tubes in Cherenkov detectors. The features of the novel detector allow for an improved system to detect and monitor UV radiation, especially during deep space missions.
The Advanced Supersonic Parachute Inflation Research and Experiments project is a flight test program for development of supersonic parachutes for future use at Mars. The flight tests are a risk-reduction program for the Mars 2020 mission. The flight tests involve two Disk-Gap- Band parachute designs to be tested at relevant Mach number and dynamic pressure regimes for the Mars 2020 entry capsule. The first of these parachutes is a built-to-print design that was successfully employed by the Mars Science Laboratory lander at Mars in August 2012, and the second is a design that is strengthened in material properties and construction methods but has the same geometry as that used by Mars Science Laboratory. The first flight test of the built-to-print parachute took place on October 4, 2017 at NASA's Wallops Flight Facility. The parachute test was successful. The second and third flight tests took place on March 31st and September 7th 2018, respectively, and successfully tested the strengthened parachute design. This paper describes the instrumentation, data analysis techniques, and atmospheric and trajectory reconstruction results from the second and third flight tests.
A subsonic wind tunnel test was conducted to determine the drag and static aerodynamic coefficients, as well as to capture the dynamic motions of a new Supersonic Ringsail parachute developed by the Low Density Supersonic Decelerator Project. To provide a comparison against current Mars parachute technology, the Mars Science Laboratory's Disk-Gap-Band parachute was also included in the test. To account for the effect of fabric permeability, two fabrics ("low" and "standard" permeability) were used to fabricate each parachute canopy type, creating four combinations of canopy type and fabric material. A wide range of test conditions were covered during the test, spanning Mach numbers from 0.09 to 0.5, and static pressures from 103 to 2116 pounds per square inch (psf) (nominal values). The fabric permeability is shown to have a first-order effect on the aerodynamic coefficients and dynamic motions of the parachutes. For example, for a given parachute type and test condition, models fabricated from "low" permeability fabric always have a larger drag coefficient than models fabricated from "standard" permeability material. This paper describes the test setup and conditions, how the results were analyzed, and presents and discusses a sample of the results. The data collected during this test is being used to create and improve parachute aerodynamic databases for use in flight dynamics simulations for missions to Mars.
When a semiconductor sample is irradiated by means of an external source, emitting photons or electrons, excess carriers are produced which distribute themselves throughout the sample. One of the parameters which determine the distribution of the carriers is the surface recombination velocity. The present investigation is concerned with the recombination lifetime tau. The predominant mechanism for recombination in wide band-gap semiconductors is described by the Shockley-Read-Hall (SRH) theory. The transport equations are derived for free carriers and the radiation field. The considered theory is applied to a semiinfinite, one-dimensional semiconductor slab irradiated by light of a given frequency. Some numerical considerations based on n-type GaAs are presented. Attention is given to a determination of the radiation transmitted through the surface of the sample.
The creation of flight dynamics simulations is often part of the design, development, and flight operations of missions that include entry, descent, and landing (EDL) in their concept of operation. Such flight dynamics simulations include models for many of the EDL sub-systems. For EDL systems that include a parachute, models of the parachute’s aerodynamic characteristics must be created for inclusion in the flight dynamics simulations. Models are presented for the aerodynamic coefficients (i.e., C(D),C(Tot),C(T),C(N), and C(m,SLCP)) of Supersonic Ringsail (SSRS) and Disk-Gap-Band (DGB) parachutes as functions of total porosity, λ(T), Mach number, M, and total angle of attack, λ(T) (when necessary). The source aerodynamic coefficients data used for creating these models were obtained from a wind tunnel test of subscale parachutes. In this wind tunnel test, subscale parachutes of both parachute types were fabricated from two different fabrics with very different permeabilities. By varying the fabric permeability, while maintaining the parachute geometry constant, it was possible to vary λ(T). The fabric permeability test data necessary for the calculation of λ(T) were obtained from samples of the same fabrics used to fabricate the subscale parachutes. Although the models for the aerodynamic coefficients are simple polynomial functions of λ(T) and M, they are capable of producing good reproductions of the source data. The (λ(T), M) domains over which these models are applicable are clearly defined. The models and their domains are applicable to flight operations on Mars. The models presented in this report are not unique – other models could be created from the source data. To make the creation of alternative numerical models, the aerodynamic coefficients source data are included in this report.
The mechanism of physical vapor transport of II-VI semiconducting compounds was studied both theoretically, using a one-dimensional diffusion model, as well as experimentally. It was found that the vapor phase stoichiometry is critical in determining the vapor transport rate. The experimental heat treatment methods to control the vapor composition over the starting materials were investigated and the effectiveness of the heat treatments was confirmed by partial pressure measurements using an optical absorption technique. The effect of residual (foreign) gas on the transport rate was also studies theoretically by the diffusion model and confirmed experimentally by the measurements of total pressure and compositions of the residual gas. An in-situ dynamic technique for the transport rate measurements and a further extension of the technique that simultaneously measured the partial pressures and transport rates were performed and, for the first time, the experimentally determined mass fluxes were compared with those calculated, without any adjustable parameters, from the diffusion model. Using the information obtained from the experimental transport rate measurements as guideline high quality bulk crystal of wide band gap II-VI semiconductor were grown from the source materials which undergone the same heat treatment methods. The grown crystals were then extensively characterized with emphasis on the analysis of the crystalline structural defects.
The mechanism of physical vapor transport of II-VI semiconducting compounds was studied both theoretically, using a one-dimensional diffusion model, as well as experimentally. It was found that the vapor phase stoichiometry is critical in determining the vapor transport rate. The experimental heat treatment methods to control the vapor composition over the starting materials were investigated and the effectiveness of the heat treatments was confirmed by partial pressure measurements using an optical absorption technique. The effect of residual (foreign) gas on the transport rate was also studies theoretically by the diffusion model and confirmed experimentally by the measurements of total pressure and compositions of the residual gas. An in-situ dynamic technique for the transport rate measurements and a further extension of the technique that simultaneously measured the partial pressures and transport rates were performed and, for the first time, the experimentally determined mass fluxes were compared with those calculated, without any adjustable parameters, from the diffusion model. Using the information obtained from the experimental transport rate measurements as guideline high quality bulk crystal of wide band gap II-VI semiconductor were grown from the source materials which undergone the same heat treatment methods. The grown crystals were then extensively characterized with emphasis on the analysis of the crystalline structural defects.
The transmission resonance spectra and tunneling current-voltage characteristics for direct conduction band electrons in sawtooth GaAs-Al(x)Ga(1-x)As superlattices are computed. Only direct-gap interfaces are considered. It is found that sawtooth superlattices exhibit resonant tunneling similar to that in step superlattices, manifested by correlation of peaks and regions of negative differential resistance in the current-voltage curves with transmission resonances. The Stark shift of the resonances of step-barrier superlattices is a linear function of the field, whereas in sawtooth superlattices under strong fields the shift is not a simple function of the field. This follows from the different ways in which the two structures deform under uniform electric fields: the sawtooth deforms into a staircase, at which field strength all barriers to tunneling are eradicated. The step-barrier superlattice always presents some barrier to tunneling, no matter how high the electric field strength.
Flight test of 40 foot parachute deployed at low supersonic speed and dynamic pressure
Structural, optical, and electrical properties of AlSb, AlAs, AlP, AlN, and BN thin films deposited by sputtering and evaporation
Design of parachutes and ballutes for decelerating atmospheric entries at supersonic velocities
Parachutes for low density atmospheres, describing low and high altitude test results
The theory of heterojunction and graded bandgap solar cells was studied to help determine the material compositions and device dimensions needed for high efficiency solar cells. Because of the involved analysis of the fundamental equations describing solar cell operation, a general numerical device analysis program was used. A major part of the initial work was involved in modifying an existing silicon solar cell analysis program to account for the unique features of graded bandgap and heterojunction solar cells. The most successful III-V solar cells have so far been constructed in the GaAs and Gal-xAlxAs material systems; this project was concerned with such solar cells. The most efficient solar cell so far evaluated is an abrupt heterojunction cell with a pure AlAs layer at the surface with a GaAs substrate. The predicted efficiency for this cell is slightly larger than that of a graded bandgap Gal-xAlxAs solar cell.
The results of an experimental program to develop the epitaxial growth techniques and analytical characterization techniques to fabricate graded bandgap solar cells are reported.
A computer program was designed for the analysis of variable composition solar cells and applied to several proposed solar cell structures using appropriate semiconductor materials. The program simulates solar cells made of a ternary alloy of two binary semiconductors with an arbitrary composition profile, and an abrupt or Gaussian doping profile of polarity n-on-p or p-on-n with arbitrary doping levels. Once the device structure is specified, the program numerically solves a complete set of differential equations and calculates electrostatic potential, quasi-Fermi levels, carrier concentrations and current densities, total current density and efficiency as functions of terminal voltage and position within the cell. These results are then recorded by computer in tabulated or plotted form for interpretation by the user.