Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “B4C”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

Friction and wear of carbon-graphite materials for high-energy brakes

Caliper type brake simulation experiments were conducted on seven different carbon graphite materials formulations against a steel disk material and against a carbon graphite disk material. The effects of binder level, boron carbide (B4C) additions, SiC additions, graphite fiber additions, and graphite cloth reinforcement on friction and wear behavior were investigated. Reductions in binder level, additions of B4C, and additions of SiC each resulted in increased wear. The wear rate was not affected by the addition of graphite fibers. Transition to severe wear and high friction was observed in the case of graphite-cloth-reinforced carbon sliding against a disk of similar composition. The transition was related to the disruption of a continuous graphite shear film that must form on the sliding surfaces if low wear is to occur.

Bill, R. C.↗

Effects of applied pressure on hot-pressing of Beta-SiC

The effects of applied pressure on the densification during hot pressing of beta-SiC compacts were investigated. Beta-SiC powder is Starck made and has the average particle size of about 0.7 micrometer. Hot pressing experiments were carried out in graphite dies at temperatures of 1700 deg to 2300 deg C and at the pressures up to 1000 kg/sq cm. The compacts containing 1 weight percent B4C were examined. Sintered compacts were examined for microstructure and the Rockwell A-scale hardness was measured. The B4C addition was very effective to mitigate the hot pressing conditions. It is found that densification goes with the strengthening of the bonding and does not occur in particle deformation due to concentrated stress.

Kinoshita, M.↗

Multielement mapping of alpha-SiC by scanning Auger microscopy

Fine second-phase particles, numerous in sintered alpha-SiC, were analyzed by scanning Auger microscopy and conventional techniques. The Auger analysis utilized computer-controlled data acquisition, multielement correlation diagrams, and a high spatial resolution of 100 nm. This procedure enabled construction of false color maps and the detection of fine compositional details within these particles. Carbon, silicon oxide, and boron-rich particles (qualitatively as BN or B4C) predominated. The BN particles, sometimes having a carbon core, are believed to result from reaction between B4C additives and nitrogen sintering atmospheres.

Browning, Ray↗

Development of Ceramic Matrix Composites For High Temperature Applications

The microstructure and mechanical properties of carbon fiber reinforced silicon carbide (C/SiC) composites that incorporated molecular-level oxidation inhibitors designed to increase the material s high temperature durability were characterized. The viability of a fiber-level inhibitor incorporated as part of a layered interface system as well as a molecularly-integrated matrix-level oxidation inhibitor that is co-deposited with the SiC matrix during Chemical Vapor Infiltration (CVI) was determined. It was expected that the inhibitor would act as a glass former that will getter the oxygen and form a crack sealant to reduce further ingress of oxygen into the composite. Three composites were examined. Composite A was a baseline C(sub f)/SiC(sub m) composite that incorporated a approx. 0.4 micron pyrolytic carbon (PyC) fiber coating to promote strength and toughness, and a CVI-derived SiC matrix. Composite B was a C(sub f)/SiC(sub m) composite incorporating a approx 0.4 micron pyrolytic carbon (PyC) fiber coating to promote strength and toughness, a approx. 0.6 micron B4C fiber-level oxidation barrier coating, and a CVI-derived SiC matrix. Composite C was a C(sub f) /SiC(sub m) composite that incorporated a approx. 0.4 micron pyrolytic carbon (PyC) fiber coating to promote strength and toughness, a approx. 0.6 micron B4C fiber-level oxidation barrier coating, and a BxC-SiC oxidation-inhibited matrix produced by CVI co-deposition. All composites were reinforced with 10 plies of T-300 balanced plain weave carbon fabric with 3K tows at 12.5 ends per inch.

Heimann, Paula↗

Inhibition of Oxidation in Nuclear Graphite

Graphite is a fundamental material of high temperature gas cooled nuclear reactors, providing both structure and neutron moderation. Its high thermal conductivity, chemical inertness, thermal heat capacity, and high thermal structural stability under normal and off normal conditions contribute to the inherent safety of these reactor designs. One of the primary safety issues for a high temperature graphite reactor core is the possibility of rapid oxidation of the carbon structure during an off normal design basis event where an oxidizing atmosphere (air ingress) can be introduced to the hot core. Although the current Generation IV high temperature reactor designs attempt to mitigate any damage caused by a postualed air ingress event, the use of graphite components that inhibit oxidation is a logical step to increase the safety of these reactors. Recent experimental studies of graphite containing between 5.5 and 7 wt% boron carbide (B4C) indicate that oxidation is dramatically reduced even at prolonged exposures at temperatures up to 900°C. The proposed addition of B4C to graphite components in the nuclear core would necessarily be enriched in B-11 isotope in order to minimize B-10 neutron absorption and graphite swelling. The enriched boron can be added to the graphite during billet fabrication. Experimental oxidation rate results and potential applications for borated graphite in nuclear reactor components will be discussed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Qualification of JEFF3.1.1 library for high conversion reactor calculations using the ERASME/R experiment

With its low CO{sub 2} production, Nuclear Energy appears to be an efficient solution to the global warming due to green-house effect. However, current LWR reactors are poor uranium users and, pending the development of Fast Neutron Reactors, alternative concepts of PWR with higher conversion ratio (HCPWR) are being studied again at CEA, first studies dating from the middle 80's. In these French designs, low moderation ratio has been performed by tightening the lattice pitch, achieving a conversion ratio of 0.8-0.9 with a MOX fuel coming from PWR UOX recycling. Theses HCPWRs are characterized by a harder neutron spectrum and the calculation uncertainties on the fundamental neutronics parameters are increased by a factor 3 regarding a standard PWR lattice, due to the major contribution of the Plutonium isotopes and of the epithermal energy range to the reaction rates. In order to reduce these uncertainties, a 3-year experimental validation program called ERASME has been performed by CEA from 1984 to 1986 in the EOLE reactor. Monte Carlo analysis of the ERASME/R experiments with the Monte Carlo code TRIPOLI4 allowed the qualification of the recommended JEFF.3.1.1 library for major neutronics parameters. K{sub eff} of the MOX under-moderated lattice is over-predicted by 440 {+-} 830 pcm (2{sigma}); the conversion ratio, indicator of the good use of uranium, is also slightly over-predicted: 2 % {+-} 4 % (2{sigma}) and the same for B4C absorber rods worth and soluble boron worth, over-predicted by 2 %, both in the 2 standard deviations range. The radial fission maps of heterogeneities (water-holes, B4C and fertile rods) are well reproduced: maximal (C-E)/E dispersion is 1.3 %, maximal power peak error is 2.7 %. The void reactivity worth is the only parameter poorly calculated with an overprediction of +12.4% {+-} 1.5%. ERASME/R analysis of MOX reactivity, void effect and spectral indexes will contribute to the reevaluation of {sup 241}Am and Plutonium isotopes nuclear data for the next library JEFF3.2. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Neutronics Analysis of Cold Critical KRUSTY Experiments using MCNP and Serpent

Kilowatt Reactor Using Stirling Technology (KRUSTY) is a prototype designed as a proof of concept for NASA’s Kilo power program, which was funded in order to create a small reactor for various space applications such as providing power for a colony on Mars or the moon and eventually as a possible option for powering rockets on deep space missions. KRUSTY was tested at the National Criticality Experiments Research Center (NCERC) located at the Nevada National Security Site (NNSS) from November 2017, through March 2018. The experimental campaign was conducted in four phases: com ponent critical experiments, cold critical experiments, warm critical runs, and high temperature demonstration. The component critical and cold critical experiments were used to determine the worth of the beryllium oxide (BeO) reflector rings and the boron carbide (B4C) control rod disks under different conditions. These conditions were altered by the addition and subtraction of other components in the assembly. The component critical phase was performed at atmospheric pressure and had four solid support rods spanning the center core; whereas the cold critical phase had the center core placed in a vacuum chamber and eight sodium-filled heat pipes spanning the center core region. This summary discusses the static neutronic analysis completed on the cold critical phase of the campaign using MCNP ® and Serpent. These two codes were used to assess any potential differences or biases in the simulation results. Understanding these potential biases is a key step toward the final goal of being able to fully analyze the transient experiments performed during phases 3 and 4 of the campaign.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Update on Benchmark Analysis of Component Critical Configurations of KRUSTY

Kilowatt Reactor Using Stirling Technology (KRUSTY) is prototype designed as a proof of concept for NASA’s Kilo power program, which was funded in order to create a small reactor for various space applications such as providing power for a colony on Mars or the moon and eventually as a possible option for powering rockets on deep space missions. Before the final prototype design was tested in March 2018, the component critical configuration, which had less external equipment than the prototype design, was created in November 2017. Both of these designs had less external equipment than the final version will have. This component critical con figuration was used to determine the worth of the beryllium oxide (BeO) reflector and of the boron carbide (B4C) control rod as well as creating necessary benchmark configurations.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Fission Yield Measurements from Highly Enriched Uranium Irradiated Inside a Boron Carbide Capsule

A boron carbide capsule was previously designed and tested by Pacific Northwest National Laboratory (PNNL) and Washington State University (WSU) for spectral-tailoring in mixed spectrum reactors. The presented work used this B4C capsule to create a fission product sample from the irradiation of highly enriched uranium (HEU) with a fast fission neutron spectrum. An HEU foil was irradiated inside of the capsule in WSU’s 1 MW TRIGA reactor at full power for 200 min to produce 5.8 × 1013 fissions. After three days of cooling, the sample was shipped to PNNL for radiochemical separations and analysis by gamma and beta spectroscopy. Fission yields for products were calculated from the radiometric measurements and compared to measurements from thermal neutron induced fission (analyzed in parallel with the non-thermal sample at PNNL) and published evaluated fast-pooled and thermal nuclear data. Reactor dosimetry measurements were also completed to fully characterize the neutron spectrum and total fluence of the irradiation.

boron carbide↗

Metal/ceramic interface structures and segregation behavior in aluminum-based composites

Trimodal Al alloy (AA) matrix composites consisting of ultrafine-­grained (UFG) and coarse-­ grained (CG) Al phases and micron-­sized B 4 C ceramic reinforcement particles exhibit combinations of strength and ductility that render them useful for potential applications in the aerospace, defense and automotive industries. Tailoring of microstructures with specific mechanical properties requires a detailed understanding of interfacial structures to enable strong interface bonding between ceramic reinforcement and metal matrix, and thereby allow for effective load transfer. Trimodal AA metal matrix composites typically show three characteristics that are noteworthy: nanocrystalline grains in the vicinity of the B4C reinforcement particles; Mg segregation at AA/B 4 C interfaces; and the presence of amorphous interfacial layers separating nanocrystalline grains from B 4 C particles. Interestingly, however, fundamental information related to the mechanisms responsible for these characteristics as well as information on local compositions and phases are absent in the current literature. Here in this study, we use high-­resolution transmission electron microscopy, energy-­dispersive X-­ray spectroscopy, electron energy-­loss spectroscopy, and precession assisted electron diffraction to gain fundamental insight into the mechanisms that affect the characteristics of AA/B 4 C interfaces. Specifically, we determined interfacial structures, local composition and spatial distribution of the interfacial constituents. Near atomic resolution characterization revealed amorphous multilayers and a nanocrystalline region between Al phase and B 4 C reinforcement particles. The amorphous multilayers consist of nonstoichiometric Al x O y , while the nanocrystalline region is comprised of MgO nanograins. The experimental results are discussed in terms of the possible underlying mechanisms at AA/B 4 C interfaces.

36 MATERIALS SCIENCE↗

Heat Flux Calculation and Problem of Flaking of Boron Carbide Coatings on the Faraday Screen of the ICRH Antennas During Tore Supra High Power, Long Pulse Operation

Reliable and repetitive high power and long pulse tokamak operation is strongly dependant of the ability to secure the Plasma Facing Components (PFCs). In Tore Supra, a network of 7 infrared (IR) video cameras is routinely used to prevent PFCs overheating and damage in selected regions. Real time feedback control and offline analysis are essential for basic protection and understanding of abnormal thermal events. One important limitation detected by the IR real time feed-back loop during high power RF operation (injected power of 9.5 MW over 26 s and 12 MW over 10 s have been achieved respectively in 2006 and 2008) is due to the interaction between fast ions which increase the power flux density and flaking of the boron carbide coatings on the Faraday screen box of the ICRH antennas. An IR-based experimental procedure is proposed in order to detect new flakes during plasma operation. The thermal response of the B4C coating is studied with and without flaking during plasma operation. The experimental heat flux deposited by fast ion losses on the Faraday screen is calculated for high (3.8 T) and low magnetic field (2 T) during high RF power operation (with fundamental hydrogen minority and second harmonic ICRH heating schemes respectively). The paper addresses both thermal science issues applied to machine protection and limitation due to fast ions issues during high RF power, long pulse operation. Safety margin to critical heat flux and number of fatigue cycles under heat load are presented in the paper.

Corre, Y.↗

Electron diffraction radial distribution function analysis of amorphous boron carbide synthesized by ion beam irradiation and chemical vapor deposition

Amorphous boron carbide (a-BxC) networks consist of light elements, and their low atomic scattering factors makes structural analysis by x-ray diffraction difficult. Electron diffraction has an advantage of detecting the light elements, because of the strong interaction between the matter and electrons. In this work, we prepared a-BxC by ion beam technologies and plasma-enhanced chemical vapor deposition, and characterized their structures via atomic pair-distribution functions derived from electron diffraction intensity profiles. It was found that a pentagonal pyramid is the most favorable cluster in a-B4C generated by ion irradiation, while C—C homonuclear bonds were formed in the deposited a-B x C thin film. X-ray photoemission spectroscopy revealed that the a-BxC thin film possesses more carbon than B 4 C, which is responsible for the formation of the homonuclear bonds.

36 MATERIALS SCIENCE↗

Laser-induced slip casting as an additive manufacturing approach for silicon carbide

Here, this work presents processing silicon carbide (SiC) with the laser-induced slip casting (LIS) additive manufacturing (AM). SiC was stabilized in water with polyethyleneimine (PEI) dispersant, and SiC slurries were made with rheology for LIS printing. High-density ceramic parts were printed, followed by single-step binder burnout and sintering. The printed parts achieved 93–95 % of theoretical density. X-ray computed tomography (XCT) revealed a small distribution of flaws exceeding 100 microns. The mechanical properties were measured in both parallel and perpendicular to the printing layers, and the orientation with layers perpendicular to the bending moment resulted in higher strength compared to the parallel direction. Porosity resulting from processing and large inclusions of boron carbide (B4C) were the root cause of failure in the measured samples. Despite these defects through this effort, this new approach demonstrates promise for green forming of SiC with densities greater than 95 % theoretical and tensile strengths above 250 MPa.

Additive Manufacturing↗

Directional amorphization of covalently-bonded solids: A generalized deformation mechanism in extreme loading

Shock compression subjects materials to a unique regime of high quasi-hydrostatic pressure and coupled shear stresses for durations on the order of 1–10 nanoseconds for laser-driven loading of samples. There is, additionally, an attendant temperature increase due to the shock and the mechanisms of plastic deformation in metals whereby dislocations, twins, and phase transitions nucleate and propagate at velocities near the sound speed. Covalently bonded materials have, by virtue of the directionality of their bonds, great difficulty in responding by conventional plastic deformation to this extreme regime of shock compression. Here, we propose that the shear from shock compression induces amorphization, as observed in Si, Ge, B4C, SiC, and olivine ((Mg, Fe) 2 SO 4 ) and that this is a general deformation mechanism in a broad class of covalently bonded materials. The crystalline structure transforms to amorphous along regions of maximum shear stress, forming nanoscale bands, and thereby relaxing the shear component of the imposed shock stress. This process is usually preceded by the emission and propagation of a critical concentration of dislocations.

36 MATERIALS SCIENCE↗

Oblique angle deposition of boron carbide films by magnetron sputtering

Many applications of boron carbide (B4C) films entail deposition on non-planar substrates, necessitating a better understanding of oblique angle deposition phenomena. Here, we systematically study the effect of substrate tilt on properties of B 4 C films with thicknesses up to 10 μm deposited by direct current magnetron sputtering. Results show that all films are amorphous and columnar with an average column width of ~100 nm, independent of substrate tilt. Column tilt angles are limited to ~20° even for substrate tilt of 80°. Film density, residual stress, and the refractive index weakly (within ≲20%) depend on substrate tilt. Furthermore, oxygen impurities bond preferentially with carbon atoms in inter-columnar regions. Substrate tilt has a major effect on mechanical properties that decrease by ~50%, suggesting weak interconnection between nano-columns. Implications of these observations for the deposition onto non-planar substrates are discussed.

36 MATERIALS SCIENCE↗

High-Rate Sputter Deposition of Ultrathick Boron Carbide Coatings on Rolling Spherical Substrates

Amorphous boron carbide (B 4 C) is a promising next-generation ablator material for inertial confinement fusion. However, the deposition of ultrathick B4C coatings with submicron-scale density uniformity on spherical substrates, as required for ablator shell fabrication, remains challenging. Here, in this study, we use direct current magnetron sputtering to deposit B 4 C onto 2-mm-diameter Si spheres rolling in a dish-shaped substrate holder. High deposition rates of ∼3 μm/h are achieved. Ultrathick films have a columnar microstructure, with the column width determined by the density of nodular defects. Nodular defect nucleation is dominated by the pickup of particulates from the holder during substrate rolling. We demonstrate the fabrication of a hollow B 4 C spherical shell with a wall thickness of 80 μm. Also demonstrated is the laser machining of holes in the B 4 C coating, which is necessary for both the chemical removal of the Si template and the attachment of a fusion fuel fill tube.

Inertial confinement fusion targets↗

High-Power Impulse Magnetron Sputter Deposition of Boron Carbide with Full-Face Erosion Magnetron and Mixed Ar-Ne Plasma

Boron carbide (B 4 C) is an attractive inertial confinement fusion ablator material. The fabrication of B4C ablators by magnetron sputtering requires process optimization. To increase process flexibility, here we explore high-power impulse magnetron sputter (HiPIMS) deposition of B 4 C in pure Ar and mixed Ar-Ne plasmas. Here, the results show that higher plasma discharge currents can be reached with a mixed Ar-Ne plasma in the entire working pressure range studied (5 𝑡𝑜 50 mTorr). At 45 mTorr with 10% of Ne in the Ar-Ne mix, high peak target current densities of ~1 A cm −2 were demonstrated. Films deposited with such a mixed Ar-Ne plasma with a full-face erosion magnetron source on substrates biased at −25 V exhibited higher density and improved mechanical properties, albeit with higher compressive residual stresses compared to the case of HiPIMS deposition in a pure Ar plasma. This work demonstrates additional process flexibility of the HiPIMS discharge mode for the deposition of B 4 C coatings.

Ablator capsule↗

High-entropy boride–carbide ceramics by sequential boro/carbothermal synthesis

We report a dual-phase high-entropy boride/carbide ceramic with fine grain size was synthesized by a sequential boro/carbothermal process. In the first step, a Hf-Nb-Ta-Ti-Zr-containing carbide was synthesized by carbothermal reduction of oxides followed by reaction of the carbide with B4C and ZrH2 to convert part of the carbide to boride. The resulting composition was ~29 vol% high-entropy boride with an average grain size of ~1.1 µm. Solid solution formation occurred at the densification temperature of 1900°C resulting in a relative density higher than 99%. The Vickers’ hardness was 26.5 ± 1.4 GPa. This is the first report of synthesizing dual-phase boride-carbide high-entropy ceramics from carbothermally synthesized, high-entropy carbide powders.

36 MATERIALS SCIENCE↗