Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Attitude Control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Solar Anomalous and Magnetospheric Particle Explorer attitude control electronics box design and performance

The attitude Control Electronics (ACE) Box is the center of the Attitude Control Subsystem (ACS) for the Solar Anomalous and Magnetospheric Particle Explorer (SAMPEX) satellite. This unit is the single point interface for all of the Attitude Control Subsystem (ACS) related sensors and actuators. Commands and telemetry between the SAMPEX flight computer and the ACE Box are routed via a MIL-STD-1773 bus interface, through the use of an 80C85 processor. The ACE Box consists of the flowing electronic elements: power supply, momentum wheel driver, electromagnet driver, coarse sun sensor interface, digital sun sensor interface, magnetometer interface, and satellite computer interface. In addition, the ACE Box also contains an independent Safehold electronics package capable of keeping the satellite pitch axis pointing towards the sun. The ACE Box has dimensions of 24 x 31 x 8 cm, a mass of 4.3 kg, and an average power consumption of 10.5 W. This set of electronics was completely designed, developed, integrated, and tested by personnel at NASA GSFC. SAMPEX was launched on July 3, 1992, and the initial attitude acquisition was successfully accomplished via the analog Safehold electronics in the ACE Box. This acquisition scenario removed the excess body rates via magnetic control and precessed the satellite pitch axis to within 10 deg of the sun line. The performance of the SAMPEX ACS in general and the ACE Box in particular has been quite satisfactory.

Chamberlin, K.↗
NASA NTRS1986

Attitude control of tethered spacecraft

Procedures for achieving attitude control of single-body and multibody, tethered spacecraft are examined. The design considerations for attitude control and the generation of control torques are described. Two dimensional tether attach point motion is utilized to produce torque about two axes and the third axis is controlled with either a control moment gyro or a reaction wheel. The ability to perform attitude control of a tethered spacecraft is evaluated in the Kinetic Isolation Tether Experiment (KITE). It is observed that the KITE/SPARTAN design bandwidth is adequate to fully utilize the capability of attitude sensors with accuracies in the 1-arcsec range.

Lemke, L. G.↗
NASA NTRSDate not supplied

Correlated Electromagnetic Levitation Actuator: A Reaction Sphere-Based Attitude Control System

To address problems experienced by current reaction wheels and control moment gyroscopebased attitude control systems (ACS), researchers at National Aeronautics and Space Administration’s (NASA’s) Marshall Space Flight Center (MSFC) have begun developing a reaction sphere actuator based on correlated electromagnetic levitation that will be immune to destructive bearing friction, momentum saturation, and gimbal lock. The Correlated Electromagnetic Levitation Actuator (CELA) advances the state of the art of reaction sphere ACSs by employing the concept of correlated magnetics. It is a frictionless, direct-drive reaction sphere that harnesses a unique technology with an array of applications across multiple disciplines. Correlated electromagnets function in a manner that is analogous to a matched filter; the convolution of two signals is peaked at the index representing the greatest match. For CELA, the signals are the patterns of magnetic flux density as a function of position. The magnitude of the convolution equates to an attractive or repulsive force, and these forces can be azimuthal or radial. The development of CELA is based in four distinct disciplines: Advanced Manufacturing, Prototype Development, Electromagnetic Modeling, and Controls. We are developing novel manufacturing techniques required to build arrays of permanent and electromagnet dipoles on curved surfaces. To print the permanent magnetic array, we have developed a probe with pyramidal magnets that will reside on a robotic arm to induce localized magnetic fields on a surface. We have also used high temperature ovens to erase dipole patterns from a permanent magnet by heating the surface to its Curie temperature. A number of test articles and prototypes have been developed using additive manufacturing methods. These prototypes have included hemispherical motors to test the drive algorithm, and a levitation test bed that demonstrates a magnetic bearing method based on attractive magnetic forces and ratiometric Hall effect sensors. We developed an array of electromagnetic dipoles on a printed circuit board (PCB) with individual H-bridges controlling each coil. This device created various flux density patterns and we measured their magnetic fields using a custom Hall effect 3-D probe and a LabVIEW virtual instrument. These data will serve as a benchmark for characterizing the accuracy of future models. Current work is focused on modeling the magnetic fields of our prototype arrays using COMSOL finite element analysis (FEA) and verifying the model against our test data. Accurate modeling will allow us to quickly test new patterns of electromagnets and their macro behavior. Eventually, the magnetic field models will be implemented in our controls simulations to facilitate precise control of the reaction sphere. Initial model results agree with field measurements to within 1 G (5% of measured flux density). Currently, we are testing different material properties of the electromagnets and their magnetic fields and thermal effects. These results will be used to refine the design of the electromagnetic dipoles. Our control efforts have centered on developing commutation, levitation, and field pattern shaping hardware in the form of breadboards and PCBs with software running on a local microcontroller. In addition, our partners developed MATLAB Simulink models to demonstrate a PID controller that mitigates disturbance forces resulting from the interaction of drive and levitation magnetics. Finally, we have designed a three-axis test stand that will be used in future work to demonstrate CELA’s orientation control capability.

reaction sphere↗
NASA NTRS1971

Experiment D010: Ion sensing attitude control

The feasibility of an attitude control system that uses environmental positive ions and an electrostatic detection system to measure spacecraft pitch and yaw is studied. The secondary objective was to measure the spatial and temporal variations of ambient positively charged particles along the orbital path of the Gemini 10 and 12 spacecrafts. The results proved that the use of a horizon detector in conjunction with pitch and yaw sensors would facilitate complete description of the spacecraft position and attitude. Furthermore, with the addition of a servosystem, the unit could be used as a complete automatic attitude-control system that would be applicable from the lowest satellite altitudes up to at least 10 earth radii. Also, results established that the charge density along the trajectory of the satellite could be determined by transmission of output voltages from the individual electrometers.

Sagalyn, R. C.↗
NASA NTRS1973

The development and demonstration of hybrid programmable attitude control electronics

In the course of extended life attitude control system (ELACS) research sponsored by NASA a hybrid programable attitude control electronics (HYPACE) concept was developed and demonstrated. The wide variety of future planetary missions demanded a new control approach to accommodate the automatic fault tolerance and long the life requirements of such missions. HYPACE provides an adaptable, analog/digital design approach that permits preflight and in-flight accommodation of mission changes, component performance variations, and spacecraft changes, through programing. This enabled broad multimission flexibility of application in a cost effective manner. Previously, flight control computers have not been not flown on planetary missions because of weight and power problems. These problems were resolved in the design of HYPACE. The HYPACE design, which was demonstrated in breadboard form on a single-axis gas-bearing spacecraft simulation, uses a single control channel to perform the attitude control functions sequentially, thus significantly reducing the number of component parts over hard-wired designs.

Smith, L. S.↗
NASA NTRS1985

Advanced Integrated Power and Attitude Control System (IPACS) study

Integrated Power and Attitude Control System (IPACS) studies performed over a decade ago established the feasibility of simultaneously satisfying the demands of energy storage and attitude control through the use of rotating flywheels. It was demonstrated that, for a wide spectrum of applications, such a system possessed many advantages over contemporary energy storage and attitude control approaches. More recent technology advances in composite material rotors, magnetic suspension systems, and power control electronics have triggered new optimism regarding the applicability and merits of this concept. This study is undertaken to define an advanced IPACS and to evaluate its merits for a space station application. System and component designs are developed to establish the performance of this concept and system trade studies conducted to examine the viability of this approach relative to conventional candidate systems. It is clearly demonstrated that an advanced IPACS concept is not only feasible, but also offers substantial savings in mass and life-cycle cost for the space station mission.

Oglevie, R. E.↗
NASA NTRS2005

Solar Sail Attitude Control Performance Comparison

Performance of two solar sail attitude control implementations is evaluated. One implementation employs four articulated reflective vanes located at the periphery of the sail assembly to generate control torque about all three axes. A second attitude control configuration uses mass on a gimbaled boom to alter the center-of-mass location relative to the center-of-pressure producing roll and pitch torque along with a pair of articulated control vanes for yaw control. Command generation algorithms employ linearized dynamics with a feedback inversion loop to map desired vehicle attitude control torque into vane and/or gimbal articulation angle commands. We investigate the impact on actuator deflection angle behavior due to variations in how the Jacobian matrix is incorporated into the feedback inversion loop. Additionally, we compare how well each implementation tracks a commanded thrust profile, which has been generated to follow an orbit trajectory from the sun-earth L1 point to a sub-L1 station.

Bladt, Jeff J.↗
NASA NTRS1981

Flight performance of SEASAT-1 attitude control system

The paper describes the attitude control flight performance of SEASAT-A, (launched in June 1978), until failure of the power subsystem terminated the mission in Oct. 1978. Information provided by the satellite pertained to surface winds and coastal storm activity, currents and wave heights, ocean topography and temperature. The ACS used three-axis momentum exchange and magnetic momentum containment and was set in a nose-down configuration. Attitude control sensing was via horizon sensors and attitude anomalies, resulting from solar interference with the sensors, is covered in detail. Remedial action was taken by reconfiguring the IR scanners, but failure resulted nevertheless. Recommendations for similar future missions include consideration of the effect of light sources and circuit time constants and scan rates. A block diagram of the ACS is included.

Beach, S. W.↗
NASA NTRS1985

Integrated Power and Attitude Control Systems for Space Station

Integrated Power and Attitude Control Systems (IPACS) studies performed over a decade ago established the feasibility of simultaneously storing electrical energy in wheels and utilizing the resulting momentum for spacecraft attitude control. It was shown that such a system possessed many advantages over other contemporary energy storage and attitude control systems in many applications. More recent technology advances in composite rotors, magnetic bearings, and power control electronics have triggered new optimism regarding the feasibility and merits of such a system. The paper presents the results of a recent study whose focus was to define an advanced IPACS and to evaluate its merits for the Space Station application. A system and component design concept is developed to establish the system performance capability. A system level trade study, including life-cycle costing, is performed to define the merits of the system relative to two other candidate systems. It is concluded that an advanced IPACS concept is not only feasible, but offers substantial savings in mass, and life-cycle cost.

Oglevie, R. E.↗
NASA NTRS1983

Modular design attitude control system

Application of modular control techniques to the attitude control of a prototype flexible spacecraft and a prototype flexible space platform was further developed by determining numerical values for the physical parameters of a four body approximation of the MSFC/hybrid deployable truss incorporated in the space platform model, generating sensitivity coefficients for the model of the flexible spacecraft, evaluating the changes in the digital computer simulation of the flexible spacecraft resulting from the addition of another rigid body to the model and comparing attitude control effectiveness with actuators on more than one rigid body of the model with that for the case in which the actuators were restricted to one body.

Chichester, F. D.↗
NASA NTRS1980

Torque equilibrium attitude control for Skylab reentry

The method of torque equilibrium attitude control used to control the reentry of Skylab to an altitude below 150 km without the use of thruster fuel once the attitude was established is discussed. The Skylab attitude and pointing control system, which included rate gyros, sun sensors, star tracker, the Apollo telescope mount digital computer, control moment gyros and cold-gas attitude thrusters, is presented. The 12 torque equilibrium attitudes found at which aerodynamic, gravity gradient and gyroscopic torques would balance are indicated, and the three of those at which the solar power supply would be adequate for attitude control are illustrated. The equilibrium seeking method employed is then examined, and the operation and performance of the torque equilibrium attitude control system during the three weeks prior to Skylab reentry are discussed. It is concluded that the torque equilibrium attitude control method developed for Skylab was successful in performing its assigned mission, and will be valuable for the design of future, low-altitude spacecraft or tethered vehicles.

Glaese, J. R.↗