Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Aircraft Position”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS2002

Wind Tunnel Measurements and Calculations of Aerodynamic Interactions Between Tiltrotor Aircraft

Wind tunnel measurements and calculations of the aerodynamic interactions between two tiltrotor aircraft in helicopter mode are presented. The measured results include the roll moment and thrust change on the downwind aircraft, as a function of the upwind aircraft position (longitudinal, lateral, and vertical). Magnitudes and locations of the largest interactions are identified. The calculated interactions generally match the measurements, with discrepancies attributed to the unsteadiness of the wake and aerodynamic forces on the airframe. To interpret the interactions in terms of control and power changes on the aircraft, additional calculations are presented for trimmed aircraft with gimballed rotors.

Johnson, Wayne↗
NASA NTRS1973

The effect of communications and traffic situation displays on pilots awareness of traffic in the terminal area

The Air Traffic Control (ATC) system is evolving under a general plan specified by the Federal Aviation Administration. Among the developments being considered is the Discrete Address Beacon System (DABS). The use of this system, although relieving congestion on the communications frequencies, would eliminate information about other aircraft because the party line communications now in use would be lost. One alternative to restore this lost information is an Airborne Traffic Situation Display (TSD). Experienced airline and military pilots participated in a factorial design to evaluate two types of communication (discrete address, party line) and two types of displays (TSD, no TSD). A stop-action quiz was used to evaluate their knowledge of other aircrafts' position, altitude, speed, heading, rate of climb, identity, and landing sequence number. Significant differences between conditions were detected, primarily in the position variables. Workload, as measured by a spare capacity side-task, showed a main effect of displays and a significant interaction between displays and communications. The data are summarized by plotting each display/communication condition configuration in the plane defined by information and workload index. A limited number of blunders by other aircraft were included in the simulations with a significant, but not entirely satisfactory, improvement in blunder detection attributed to the TSD.

Melanson, D.↗
NASA NTRS1995

Ground-recorded sonic boom signatures of F-18 aircraft formation flight

Two F-18 aircraft were flown, one above the other, in two formations, in order for the shock systems of the two aircraft to merge and propagate to the ground. The first formation had the canopy of the lower F-18 in the inlet shock of the upper F-18 (called inlet-canopy). The flight conditions were Mach 1.22 and an altitude of 23,500 ft. An array of five sonic boom recorders was used on the ground to record the sonic boom signatures. This paper describes the flight test technique and the ground level sonic boom signatures. The tail-canopy formation resulted in two, separated, N-wave signatures. Such signatures probably resulted from aircraft positioning error. The inlet-canopy formation yielded a single modified signature; two recorders measured an approximate flattop signature. Loudness calculations indicated that the single inlet-canopy signatures were quieter than the two, separated tail-canopy signatures. Significant loudness occurs after a sonic boom signature. Such loudness probably comes from the aircraft engines.

Bahm, Catherine M.↗
NASA NTRS1996

Ground-Recorded Sonic Boom Signatures of F-18 Aircraft in Formation Flight

Two F-18 aircraft were flown, one above the other, in two formations, in order for the shock systems of the two aircraft to merge and propagate to the ground. The first formation had the canopy of the lower F-18 in the tail shock of the upper F-18 (called tail-canopy). The second formation had the canopy of the lower F- 18 in the inlet shock of the upper F-18 (called inlet-canopy). The flight conditions were Mach 1.22 and an altitude of 23,500 ft . An array of five sonic boom recorders was used on the ground to record the sonic boom signatures. This paper describes the flight test technique and the ground level sonic boom signatures. The tail-canopy formation resulted in two, separated, N-wave signatures. Such signatures probably resulted from aircraft positioning error. The inlet-canopy formation yielded a single modified signature; two recorders measured an approximate flattop signature. Loudness calculations indicated that the single inlet-canopy signatures were quieter than the two, separated tail-canopy signatures. Significant loudness occurs after a sonic boom signature. Such loudness probably comes from the aircraft engines.

Bahm, Catherine M.↗
NASA NTRS1988

Integrated multisensor navigation systems

The multisensor navigation systems research evolved from the availability of several stand alone navigation systems and the growing concern for aircraft navigation reliability and safety. The intent is to develop a multisensor navigation system during the next decade that will be capable of providing reliable aircraft position data. These data will then be transmitted directly, or by satellite, to surveillance centers to aid the process of air traffic flow control. In order to satisfy the requirements for such a system, the following issues need to be examined: performance, coverage, reliability, availability, and integrity. The presence of a multisensor navigation system in all aircraft will improve safety for the aviation community and allow for more economical operation.

Vangraas, Frank↗
NASA NTRS1988

Windshear detection and avoidance - Airborne systems perspective

The generalized windshear hazard index presently defined is derived from aircraft-position wind data and remotely sensed data obtained along the extended flight path by such candidate sensor technologies as microwave Doppler radar, Doppler lidar, and IR radiometry. Attention is given here to the results of a comparative evaluation of CO2 and Ho:YAG lidar sensor-employing windshear-detection systems, over a range 1-3 km ahead of the aircraft (corresponding to 15-45 sec of warning time). While the technology for a 10.6-micron CO2 lidar system is available, an optimum 2-micron REE laser crystal-based system remains to be developed.

Bowles, Roland L.↗
NASA NTRS1981

Airborne meteorological data-collection system

Aircraft position and weather data are collected, formatted, and relayed to ground from in-flight commercial jets. Data Acquisition and Control Unit in plane receives information from standard avionics data units, and provides scaling and storage. Normally, eight sets of data are acquired in 1 hour period and transmitted to satellite at precise time. Besides meteorological applications, system can locate and reroute aircraft into favorable winds to conserve fuel or aid search for downed planes.

Bagwell, J. W.↗
NASA NTRS1987

Aircraft noise synthesis system

A second-generation Aircraft Noise Synthesis System has been developed to provide test stimuli for studies of community annoyance to aircraft flyover noise. The computer-based system generates realistic, time-varying, audio simulations of aircraft flyover noise at a specified observer location on the ground. The synthesis takes into account the time-varying aircraft position relative to the observer; specified reference spectra consisting of broadband, narrowband, and pure-tone components; directivity patterns; Doppler shift; atmospheric effects; and ground effects. These parameters can be specified and controlled in such a way as to generate stimuli in which certain noise characteristics, such as duration or tonal content, are independently varied, while the remaining characteristics, such as broadband content, are held constant. The system can also generate simulations of the predicted noise characteristics of future aircraft. A description of the synthesis system and a discussion of the algorithms and methods used to generate the simulations are provided. An appendix describing the input data and providing user instructions is also included.

Mccurdy, David A.↗
NASA NTRS1975

Flight experience with time-of-arrival control for STOL aircraft in the terminal area

A research program on STOL operating systems is underway at the Ames Research Center. One investigation is concerned with design, analysis, and flight test of promising four-dimensional RNAV systems. One promising system generates a capture flight path from the present aircraft position to a waypoint on a selected fixed STOL approach route. It predicts arrival time at the runway and controls time and position along the path. The system was flight tested using a digital avionics system on a Convair 340 and on an experimental powered-lift STOL airplane. Flight tests in the flight director mode show that the pilot can choose and change the desired time of arrival, and meet this time within a few seconds, in spite of navigation errors and varying winds. Initial tests of the automatic mode using a flight simulator and the NASA Augmentor Wing Jet STOL Research Aircraft (AWJSRA) show that good time control was achieved at the cost of excess throttle activity. This fault was later corrected.

Neuman, F.↗
NASA NTRS2013

Effects of Airport Tower Controller Decision Support Tool on Controllers Head-Up Time

Despite that aircraft positions and movements can be easily monitored on the radar displays at major airports nowadays, it is still important for the air traffic control tower (ATCT) controllers to look outside the window as much as possible to assure safe operations of traffic management. The present paper investigates whether an introduction of the NASA's proposed Spot and Runway Departure Advisor (SARDA), a decision support tool for the ATCT controller, would increase or decrease the controllers' head-up time. SARDA provides the controller departure-release schedule advisories, i.e., when to release each departure aircraft in order to minimize individual aircraft's fuel consumption on taxiways and simultaneously maximize the overall runway throughput. The SARDA advisories were presented on electronic flight strips (EFS). To investigate effects on the head-up time, a human-in-the-loop simulation experiment with two retired ATCT controller participants was conducted in a high-fidelity ATCT cab simulator with 360-degree computer-generated out-the-window view. Each controller participant wore a wearable video camera on a side of their head with the camera facing forward. The video data were later used to calculate their line of sight at each moment and eventually identify their head-up times. Four sessions were run with the SARDA advisories, and four sessions were run without (baseline). Traffic-load levels were varied in each session. The same set of user interface - EFS and the radar displays - were used in both the advisory and baseline sessions to make them directly comparable. The paper reports the findings and discusses their implications.

airport surface operations↗
NASA NTRS1977

Airborne navigation system performance during RNAV/MLS transition

Aircraft position error sensitivity to sensor errors and flight path geometry is analyzed during RNAV/MLS transition using a digital computer simulation. The avionics sensitivity data provides information necessary to establish requirements for additional guidance law design and to establish airspace requirements for maneuvering to null out any residual RNAV errors upon MLS transition. The data base is also beneficial as planning information for subsequent flight testing. The parameters varied during the generation of the data base include flight profile, error source content and magnitude, ground facility location, runway/flight path orientation and navigation mode. The avionics, autopilots and aircraft dynamics correspond to the existing NASA Terminal Configured Vehicle. Significant transients were observed during MLS transition, primarily in the vertical channel. These transients have a significant impact on airspace requirements and operational procedures in the RNAV/MLS environment.

Heine, W.↗
NASA NTRS2000

GeoSAR: A Radar Terrain Mapping System for the New Millennium

GeoSAR Geographic Synthetic Aperture Radar) is a new 3 year effort to build a unique, dual-frequency, airborne Interferometric SAR for mapping of terrain. This is being pursued via a Consortium of the Jet Propulsion Laboratory (JPL), Calgis, Inc., and the California Department of Conservation. The airborne portion of this system will operate on a Calgis Gulfstream-II aircraft outfitted with P- and X-band Interferometric SARs. The ground portions of this system will be a suite of Flight Planning Software, an IFSAR Processor and a Radar-GIS Workstation. The airborne P-band and X-band radars will be constructed by JPL with the goal of obtaining foliage penetration at the longer P-band wavelengths. The P-band and X-band radar will operate at frequencies of 350 Mhz and 9.71 Ghz with bandwidths of either 80 or 160 Mhz. The airborne radars will be complemented with airborne laser system for measuring antenna positions. Aircraft flight lines and radar operating instructions will be computed with the Flight Planning Software The ground processing will be a two-step step process. First, the raw radar data will be processed into radar images and interferometer derived Digital Elevation Models (DEMs). Second, these radar images and DEMs will be processed with a Radar GIS Workstation which performs processes such as Projection Transformations, Registration, Geometric Adjustment, Mosaicking, Merging and Database Management. JPL will construct the IFSAR Processor and Calgis, Inc. will construct the Radar GIS Workstation. The GeoSAR Project was underway in November 1996 with a goal of having the radars and laser systems fully integrated onto the Calgis Gulfstream-II aircraft in early 1999. Then, Engineering Checkout and Calibration-Characterization Flights will be conducted through November 1999. The system will be completed at the end of 1999 and ready for routine operations in the year 2000.

Thompson, Thomas↗
NASA NTRS2000

Aircraft Conflict Analysis and Real-Time Conflict Probing Using Probabilistic Trajectory Modeling

Methods for maintaining separation between aircraft in the current airspace system have been built from a foundation of structured routes and evolved procedures. However, as the airspace becomes more congested and the chance of failures or operational error become more problematic, automated conflict alerting systems have been proposed to help provide decision support and to serve as traffic monitoring aids. The problem of conflict detection and resolution has been tackled from a number of different ways, but in this thesis, it is recast as a problem of prediction in the presence of uncertainties. Much of the focus is concentrated on the errors and uncertainties from the working trajectory model used to estimate future aircraft positions. The more accurate the prediction, the more likely an ideal (no false alarms, no missed detections) alerting system can be designed. Additional insights into the problem were brought forth by a review of current operational and developmental approaches found in the literature. An iterative, trial and error approach to threshold design was identified. When examined from a probabilistic perspective, the threshold parameters were found to be a surrogate to probabilistic performance measures. To overcome the limitations in the current iterative design method, a new direct approach is presented where the performance measures are directly computed and used to perform the alerting decisions. The methodology is shown to handle complex encounter situations (3-D, multi-aircraft, multi-intent, with uncertainties) with relative ease. Utilizing a Monte Carlo approach, a method was devised to perform the probabilistic computations in near realtime. Not only does this greatly increase the method's potential as an analytical tool, but it also opens up the possibility for use as a real-time conflict alerting probe. A prototype alerting logic was developed and has been utilized in several NASA Ames Research Center experimental studies.

Yang, Lee C.↗
NASA NTRS1999

Calibration of the Geosar Dual Frequency Interferometric SAR

GeoSAR is an airborne, interferometric Synthetic Aperture Radar (INSAR) system for terrain mapping, currently under development by a consortium including NASA's Jet Propulsion Laboratory (JPL), Calgis, Inc., and the California Department of Conservation (CalDOC) with funding provided by the Topographic Engineering Center (TEC) of the U.S. Army Corps of Engineers and the Defense Advanced Research Projects Agency (DARPA). The radar simultaneously maps swaths on both sides of the aircraft at two frequencies, X-Band and P-Band. For the P-Band system, data is collected for two across track interferometric baselines and at the crossed polarization. The aircraft position and attitude are measured using two Honeywell Embedded GPS Inertial Navigation Units (EGI) and an Ashtech Z12 GPS receiver. The mechanical orientation and position of the antennas are actively measured using a Laser Baseline Metrology System (LBMS). In the GeoSAR motion measurement software, these data are optimally combined with data from a nearby ground station using Ashtech PNAV software to produce the position, orientation, and baseline information are used to process the dual frequency radar data. Proper calibration of the GeoSAR system is essential to obtaining digital elevation models (DEMS) with the required sub-meter level planimetric and vertical accuracies. Calibration begins with the determination of the yaw and pitch biases for the two EGI units. Common range delays are determined for each mode, along with differential time and phase delays between channels. Because the antennas are measured by the LBMS, baseline calibration consists primarily of measuring a constant offset between mechanical center and the electrical phase center of the antennas. A phase screen, an offset to the interferometric phase difference which is a function of absolute phase, is applied to the interferometric data to compensate for multipath and leakage. Calibration parameters are calculated for each of the ten processing modes, each of the operational bandwidths (80 and 160 MHZ), and each aircraft altitude. In this talk we will discuss the layout calibration sites, the synthesis of data from multiple flights to improve the calibration, methods for determining time and phase delays, and techniques for determining radiometric and polarimetric quantities. We will describe how calibration quantities are incorporated into the processor and pre-processor. We will demonstrate our techniques applied to GeoSar data and assess the stability and accuracy of the calibration. This will be compared to the modeled performance determined from calibrating the output of a point target simulator. The details of baseline determination and phase screen calculation are covered in related talks.

Chapine, Elaine↗
NASA NTRSDate not supplied

Propeller Source Noise Separation from Flight Test Measurements of the Joby Aviation Aircraft

The Vold-Kalman order-tracking filter is applied to full-scale acoustic flight test measurements of the Joby Aviation eVTOL aircraft. Using synchronized acquisition of the aircraft position, time-varying rotation rates of each propeller, and any given single-channel acoustic signal, harmonic and nonharmonic acoustic content can be separated. Furthermore, this time-domain technique can also separate harmonic content amongst individual propellers, providing additional physical insight into the total acoustic field. A 60 kt level flyover and hover are used to exemplify the effectiveness of the method. Results clearly demonstrate the ability to rank propulsors in terms of their relative importance without the use of phased arrays. Frequency- and order-domain results are provided, as well as noise hemispheres to illustrate directivity and individual propeller contributions. Differences can be associated with interactional or installation effects due to the similarities in propeller states for each condition. Simulated signals that track the measured time-varying shaft rates were used to assess the proper filter pole count and bandwidth.

evtol↗
NASA NTRS2018

Ubiquitous Surveillance Notional Architecture for System-Wide DAA Capabilities in the NAS

There is an increasing demand for access to the national airspace system (NAS) by new entrants such as unmanned aircraft systems (UASs) and space vehicles. The need is driving the research into the development of a ubiquitous surveillance framework. A framework where all means of aircraft position tracking systems, both cooperative and noncooperative, would be correlated and made available to all NAS users. The architecture of an envisioned surveillance system was the focus of a recent Volpe National Transportation Systems Center research activity. In this work, the term ''Framework'' is used to characterize an operational environment that forms the context for future UAS operations. Within this framework, the use of all existing and future surveillance technologies is envisioned. Included would be all airspace locations; including coverage for airspace not under surveillance today. While these surveillance means and methods of air traffic control may currently constrain new entrant operations, they also provide the opportunity for the plethora of enabling technological capabilities with associated policies and procedures that can result in the safe, orderly and efficient operation. The focus of this paper is to survey and identify surveillance technologies to support the integration of new entrants in the NAS, and how those technologies can be aggregated.

Surveillance↗
NASA NTRS1967

Satellite navigation systems.

Satellite navigation systems for long range aircraft position fixing for air traffic control improvement

Keane, L. M.↗