Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Ablative materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Experimental performance of an ablative material as an external insulator for a hypersonic research aircraft

An ablative material composed of silica-filled elastomeric silicone was tested to evaluate its thermal and structural performance as an external insulator, or heat shield, for a hypersonic research aircraft. The material was also tested to determine whether it would form a durable char layer when initially heated and thereafter function primarily as an insulator with little further pyrolysis or char removal. Aerothermal tests were representative of nominal Mach 6 cruise conditions of the aircraft, and additional tests were representative of Mach 8 cruise and interference heating conditions. Radiant heating tests were used to simulate the complete nominal Mach 6 surface-temperature history. The silica char that formed during aerothermal tests was not durable. The char experienced a general and preferential surface recession, with the primary mechanism for char removal being erosion. Tests revealed that radiant heating is not a valid technique for simulating aerodynamic heating of the material.

Puster, R. L.↗
NASA NTRS1974

The thermal and mechanical properties of a low-density glass-fiber-reinforced elastomeric ablation material

An evaluation of the thermal and mechanical properties was performed on a molded low-density elastomeric ablation material designated as Material B. Both the virgin and charred states were examined to provide meaningful inputs to the design of a thermal protection system. Chars representative of the flight chars formed during ablation were prepared in a laboratory furnace from 600 K to 1700 K and properties of effective thermal conductivity, heat capacity, porosity and permeability were determined on the furnace chars formed at various temperature levels within the range. This provided a boxing of the data which will enable the prediction of the transient response of the material during flight ablation.

Engelke, W. T.↗
DOE OSTI2025

High Energy Density Physics of Inertial Confinement Fusion Ablator Materials

The historic December 5, 2022 experiment at Lawrence Livermore National Lab’s (LLNL) National Ignition Facility (NIF) reached fusion energy ignition for the first time. This is the most important scientific breakthrough of the 21st century paves the way to future clean inertial fusion energy (IFE). The diamond (high density carbon (HDC)) ablator material used in this experiment displays detrimental effects due to the development of hydrodynamic instabilities at the diamond/fuel interface under shock compression. New alternatives to diamond ablators are required to step up the energy yield in ICF experiments. The unique combination of mechanical strength (approaching that of diamond), the ability to accommodate high-Z dopants (in contrast to diamond), and the tunability of the properties (through synthesis material with varying sp 3 content) make amorphous carbon (a-C) a promising material for next-generation IFE ablative capsules. However, despite its critical importance to the IFE program, the behavior of a-C carbon at extreme temperatures and pressures remains largely unexplored. The primary goals of this project were to perform groundbreaking dynamic compression experiments and predictive simulations to uncover the fundamental high-energy-density physics of amorphous carbon. Our goals were (1) to uncover the metastability range of amorphous carbon and probe phase transitions to diamond or metastable supercooled liquid carbon; (2) to acquire high-quality equation of state (EOS) data and develop an experimentally validated EOS from machine-learning MD simulations of the complex states of carbon; and (3) to uncover the complex behavior of carbon liquid in both thermodynamically stable and metastable supercooled states by accessing large areas of carbon phase diagram with amorphous samples with variable sp 3 content. Our proposed experimental program included measurements of equation of state and diffraction measurements using the Omega EP laser at the Laboratory of Laser Energetics at the University of Rochester. The theoretical/simulation program involved the development of machine-learning models of the complex response of amorphous carbon under dynamic compression by performing molecular dynamics simulations at experimental time and length scales using leadership class DOE supercomputers. Simulations guided experiments to observe predicted phenomena and acquire critical experimental data in specific pressure-temperature domains to validate theoretical models. This research delivered fundamental properties of novel amorphous carbon IFE ablator material, including phase diagram and EOS. These results will aid in IFE target design and implosion experiments. A unique combination of predictive simulations and dynamic and static experiments provided a highly inspirational intellectual environment for graduate students and postdocs involved in this project.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS2019

Assessment of a One-Dimensional Finite Element Charring Ablation Material Response Model for Phenolic-Impregnated Carbon Ablator

In this study, mathematical formulations to model charring ablation problems were numerically implemented using finite element analysis (FEA) with ABAQUS, which account for the material decomposition and progressive surface removal in the heat conduction and the surface energy balance equations. FEA was performed for a one-dimensional model to predict the temperature and ablation histories of a phenolic-impregnated carbon ablator sample (i.e., a common heat shield material for hypersonic vehicles and spacecraft) subjected to oxy-acetylene torch flame (i.e., 0.8 SLPM acetylene gas to 2.7 SLPM oxygen gas). The recovery enthalpy and convective heat transfer coefficient for the ablation model were calculated based on gas compositions and two assumed surface conditions (i.e., equilibrium and frozen). Simulations using the calculated recovery enthalpy and convective heat transfer coefficient resulted in a recession rate of 6.38 times (equilibrium) and 14.08 times (frozen) higher than the experimental data, despite fair agreement of the surface temperature. In addition, the effect of the heat transfer coefficient was investigated through a steady-state ablation analysis. The results of the analysis indicate that there is not one single value for the heat transfer coefficient that would allow the prediction to match both measured recession rate and surface temperature. Possible reasons for such an inconsistency are provided and discussed.

Thermal Protection System↗
NASA NTRS1970

Thermal performance and radio-frequency transmissivity of candidate ablation materials for S-band antenna window application on manned spacecraft

A test program was conducted in the MSC 1.5 MW arc-heated facility to evaluate the thermal performance of ablation materials having potential application as radio frequency windows. These tests were conducted for the improvement of omnidirectional antenna operating characteristics during atmospheric reentry. Since a full scale model of the Apollo command service module was available for antenna tests, this mockup was used as a basic for the tests. Test models were subjected to heating conditions simulating the nominal lunar return trajectory (AS-501) and the design trajectories, high heat load and high heating rate. RF measurements were made before and after the arc jet tests to measure attenuation effects due to the thermal degradation of the materials under consideration. The test program demonstrated that additional development is required in materials technology to achieve an ablative system with both good RF transmission characteristics and thermal-structural integrity.

Tillian, D. J.↗
NASA NTRS1995

Ablative material testing for low-pressure, low-cost rocket engines

The results of an experimental evaluation of ablative materials suitable for the production of light weight, low cost rocket engine combustion chambers and nozzles are presented. Ten individual specimens of four different compositions of silica cloth-reinforced phenolic resin materials were evaluated for comparative erosion in a subscale rocket engine combustion chamber. Gaseous hydrogen and gaseous oxygen were used as propellants, operating at a nominal chamber pressure of 1138 kPa (165 psi) and a nominal mixture ratio (O/F) of 3.3. These conditions were used to thermally simulate operation with RP-1 and liquid oxygen, and achieved a specimen throat gas temperature of approximately 2456 K (4420 R). Two high-density composition materials exhibited high erosion resistance, while two low-density compositions exhibited approximately 6-75 times lower average erosion resistance. The results compare favorably with previous testing by NASA and provide adequate data for selection of ablatives for low pressure, low cost rocket engines.

Richter, G. Paul↗
NASA NTRS2010

Modeling Initial Stage of Ablation Material Pyrolysis: Graphitic Precursor Formation and Interfacial Effects

Reactive molecular dynamics simulations are used to study initial stage of pyrolysis of ablation materials and their composites with carbon nanotubes and carbon fibers. The products formed during pyrolysis are characterized and water is found as the primary product in all cases. The water formation mechanisms are analyzed and the value of the activation energy for water formation is estimated. A detailed study on graphitic precursor formation reveals the presence of two temperature zones. In the lower temperature zone (less than 2000 K) polymerization occurs resulting in formation of large, stable graphitic precursors, and in the high temperature zone (greater than 2000 K) polymer scission results in formation of short polymer chains/molecules. Simulations performed in the high temperature zone on the phenolic resin composites (with carbon nanotubes and carbon fibers) shows that the presence of interfaces had no substantial effect on the chain scission rate or the activation energy value for water formation.

Desai, Tapan G.↗
NASA NTRS2011

A Short Review of Ablative-Material Response Models and Simulation Tools

A review of the governing equations and boundary conditions used to model the response of ablative materials submitted to a high-enthalpy flow is proposed. The heritage of model-development efforts undertaken in the 1960s is extremely clear: the bases of the models used in the community are mathematically equivalent. Most of the material-response codes implement a single model in which the equation parameters may be modified to model different materials or conditions. The level of fidelity of the models implemented in design tools only slightly varies. Research and development codes are generally more advanced but often not as robust. The capabilities of each of these codes are summarized in a color-coded table along with research and development efforts currently in progress.

Lachaud, Jean↗
NASA NTRS2001

Development of a Low-Cost, Subscale Test System to Evaluate Particle Impingement Erosion in Nozzle Ablative Materials

This viewgraph presentation gives an overview on the development of a low-cost, subscale test system to evaluate particle impingement erosion in nozzle ablative materials. Details are given on the need for a new test bed, solid fuel torch components, solid fuel torch test, additional uses for the solid fuel torch, the development of a supersonic blast tube (SSBT), and particle impingement material discrimination.

Lansing, Matthew D.↗