SEARCH · Engineering Papers

Results for “ASPEN”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

All sources NASA NTRS DOE OSTI

DOE OSTI2020

Effect of Power Plant Capacity on the CAPEX, OPEX, and LCOC of the CO2 Capture Process in Pre-Combustion Applications - Abstract

Aspen Plus v8.8 was used to simulate the pre-combustion CO2 capture process from a typical fuel gas stream at different power plant capacities ranging from 54.3 to 543 MW. Polyethylene glycol polydimethyl siloxane (PEGPDMS-1) was used as a physical solvent to capture CO2 in a countercurrent packed-bed absorber containing a structured packing (Mellapak 250Y). The process pressure was 51.4 bar and the solvent temperature was varied from 10 to 40 oC. The internal diameter of the absorber ranged from 1.9 to 7 m and the packing height from 13.9 to 45.5 m. The physico-chemical properties were obtained and modeled using the Perturbed Chain-Statistical Associating Fluid Theory (PC-SAFT) Equation-of-State (EOS). Four process constraints were imposed in Aspen Plus: (1) no flooding in the absorber, (2) the absorber height to diameter ratio (H/D) is greater than or equal 6, (3) at least 90 mol% of the CO2 capture from the fuel gas stream, and (4) the CO2 stream destined to sequestration sites should contain less than 600 ppm water concentration and less than or equal 0.5 mol% of fuel gases (H2, CO, CH4). The plant lifetime was assumed to be 30 years with an annual discount rate of 10% and an annual maintenance cost of 4% of the total capital expenses. Seven power plants with different capacities were used and for each plant, the corresponding CO2 capture process was simulated. The absorber flooding was checked using the generalized pressure drop correlation (GPDC) by Leva [1] and the capital expenditure (CAPEX), operating expenditure (OPEX), and levelized costs per ton of CO2 captured (LCOC) were calculated [2-5]. Normalized by the largest power plant capacity (543 MW) used in the simulation, the results indicated that the capital and operating expenditures increased, however, the LCOC decreased with increasing plant capacity. This behavior was due to the increased annual tonnage of the CO2 captured with plant capacity as shown in Figure 1. The calculated CAPEX, OPEX, LCOC and the tonnage of CO2 captured for the 543 MW power plant were about 52 MM$, 22 MM$/year, 7.46 $/ton and 4 MM ton/year.

Ashkanani, Husain↗

DOE OSTI2022

The Modeling of the Synfuel Production Process: Process models of Fischer-Tropsch production with electricity and hydrogen provided by various scales of nuclear plants

Synthetic fuels (synfuels), also known as electro-fuels (E-fuels), are hydrocarbon fuels produced from waste CO2 streams and water electrolysis, with electricity as the primary source of energy. To achieve substantial reductions in greenhouse gas (GHG) emissions, electricity sources must release zero carbon or near-zero carbon, as is the case with solar, wind, hydro, and nuclear power. Nuclear power is one of the largest and steadiest domestic sources of clean energy in the United States. Moreover, nuclear power has the potential to produce hydrogen economically for less than $2/kg, reaching the DOE near-term target price. Thus, using nuclear power to produce synfuels has the unique potential to significantly reduce the GHG emissions of hydrocarbon fuels production and end-use applications. Fisher-Tropsch or FT fuel (a mixture of naphtha, jet fuel, and diesel) is of great interest because it is a drop-in fuel that can be blended with conventional petroleum counterparts and is compatible with existing infrastructure. By using the ASPEN Plus model, this report develops FT fuel production models on three scales, corresponding to nuclear plants with capacities of 1000 MWe, 437 Mwe, and 100 MWe, respectively. The FT model case with energy from a 437-MWe nuclear plant is used as a baseline case. This report summarizes the baseline ASPEN Plus model results with a detailed mass and energy analysis. Our modeled facility produces 507 MT/day (185,000 gal/day) of FT fuel by converting 255 MT/day of hydrogen and 1,580 MT/day of CO2. The FT fuel production energy efficiency from hydrogen and electricity energy inputs is 70% (lowerheating-value or LHV-based). Including the high-temperature electrolyzer in the system boundary, the FT fuel production LHV efficiency from electricity and thermal energy inputs is 51%, considering 39.8 kWh/kg of electricity and 6.86 kWh/kg of thermal energy use from a nuclear plant for hydrogen production. The FT production efficiency can potentially be increased by further integrating the heat exchange between nuclear plant and FT process, and this study is underway. The carbon conversion ratio in the baseline case is 99%, with process CO2 capture and recirculation and oxy-combustion using the oxygen by-product from water electrolysis. The hydrogen consumption is 1.38 kg/gal-FT fuel and the CO2 consumption is 8.56 kg/gal-FT fuel in the baseline case. With different FT production scales determined by the nuclear plant capacity, the FT model was scaled using the same operating parameters, which led to the same conversion efficiency regardless of scale. However, the different FT plant scales will impact the economics of FT fuel production; this impact will be examined in the next phase of this study.

Zang, Guiyan↗

DOE OSTI2023

Estimating the Value of Nuclear Integrated Hydrogen Production and the Dependency of Electricity and Hydrogen Markets on Natural Gas

Producing low carbon Hydrogen at a competitive price is one of the challenges to hydrogen being part of the solution to reach net-zero emission targets set by the U.S. DOE by 2050. With projected near-term improvements in technology, hydrogen production via solid oxide electrolysis cell (SOEC) / high-temperature steam electrolysis (HTSE) integrated with existing light water reactor (LWR) Nuclear Power Plants (NPP-HTSE) can produce carbon-free hydrogen competitively. In the near term, a 10-year production tax credit (PTC) found in the Inflation Reduction Act (IRA) has been passed, which will catalyze the development and improvement of hydrogen production technology to be competitive. The “1-1-1” target set by the U.S. DOE is to reduce the cost of carbon-free hydrogen by 80% to $1 per kilogram in 1 decade. Several models are available to analyze the profitability, opportunity, and technical capability of NPP-HTSE systems. In order of complexity from most complex to least complex some of these models include: RAVEN/HERON, process models using Aspen HYSYS and capital expense estimations using Aspen Process Economic Analyzer (APEA) and levelized cost of hydrogen (LCOH) calculation using the H2A model (Hydrogen Analysis Model), and custom spread sheets built by the interested party. Though some of the more advanced existing models provide detailed analysis to complex grid integrated problems, they also can take considerable time to setup and run. These advanced models are well suited to complex grid integrated analysis and the consideration of flexibility and variability of regulated and de-regulated electricity price and advanced estimation of capital and operating expenses and heat and material balances.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2024

A high fidelity and user-friendly equation-oriented optimization model for carbon capture using a novel water-lean solvent

Research Triangle Institute (RTI) International and SLB have developed a novel water-lean solvent technology for carbon capture, demonstrating low specific reboiler duty (SRD) values at capture rates exceeding 90%. At the Technology Centre Mongstad (TCM) pilot plant, the technology achieved an SRD of 2.55 GJ/t-CO2 at 95% capture, utilizing an intercooler and a 5°C temperature approach in the lean/rich solvent cross exchanger. To meet varying carbon capture targets for Front End Engineering and Design (FEED) studies and to enable real-time optimization and advanced process control, an efficient optimization model is required. This model needs to minimize energy demand for a given capture rate and determine optimal operating parameters in response to fluctuating flue gas conditions. While an existing Aspen Plus simulation model, developed by RTI and SLB, accurately matches TCM plant data, its sequential modular (SM) strategy is too slow for real-time applications due to recycle streams and tight heat integration inherent in solvent-based carbon capture processes. Although an equation-oriented (EO) modeling strategy is more suitable for optimizing these processes, its adoption has been limited by several factors: feature limitations in Aspen Plus EO mode (e.g., lack of balance block support), a less user-friendly interface for variable identification and loop solving, complex troubleshooting of convergence issues, and the necessity for accurate initial values.

carbon capture↗

DOE OSTI2021

Microalgae to biofuels through hydrothermal liquefaction: Open-source techno-economic analysis and life cycle assessment

Hydrothermal liquefaction is a promising conversion technology in algae biofuel research due to its ability to agnostically convert proteins, carbohydrates, and lipids to biocrude. The high-temperature conditions that define this conversion process require the material to maintain a subcritical liquid state, which complicates the assessment of accurate thermochemical properties due to the required pressure. To clarify this issue, this work compares the estimated performance of algal hydrothermal liquefaction between different thermodynamic models. A process model was developed in Aspen Plus from a robust assessment of current literature. Techno-economic assessment and life-cycle assessment metrics are derived from this model and used as key performance indicators. The baseline fuel price contribution of hydrothermal liquefaction is $0.45 per liter gasoline equivalent. Independently decreasing the temperature from 350 °C to 260 °C while maintaining yield reduces the conversion cost by 19%, illustrating the importance of understanding the high-temperature thermodynamics of the system. Different thermodynamic property models can vary fuel conversion cost results by $0.07 per liter gasoline equivalent. The baseline global warming potential is +23 g CO 2 eq MJ -1 and the net energy ratio is 0.30. Environmental metrics beyond global warming potential and net energy ratio are also discussed for the first time. Uncertainties in conversion performance are bounded through a scenario analysis that manipulates parameters such as product yield and nutrient recycle to produce a range of economic and environmental metrics. The report is supplemented with an open source model to support future hydrothermal liquefaction assessments and accelerate the development of commercial-scale systems.

09 BIOMASS FUELS↗

DOE OSTI2022

Physics-informed machine learning modeling for predictive control using noisy data

Due to the occurrence of over-fitting at the learning phase, the modeling of chemical processes via artificial neural networks (ANN) by using corrupted data (i.e., noisy data) is an ongoing challenge. Therefore, this work investigates the effect of both Gaussian and non-Gaussian noise on the performance of process-structure based recurrent neural networks (RNN) models, which take the form of partially-connected RNN models in this work, that are used to approximate a class of multi-input-multi-outputs nonlinear systems. Furthermore, two different techniques, specifically Monte Carlo dropout and co-teaching, are utilized in the development of partially-connected RNN models. Here, these two techniques are employed to reduce the over-fitting in ANNs when noisy data is used in the training process and, hence, to improve the open-loop accuracy as well as the closed-loop performance under a Lyapunov-based model predictive controller (MPC). Aspen Plus Dynamics, a well-known high-fidelity process simulator, is used to simulate a large-scale chemical process application in order to demonstrate the anticipated improvements in both open-loop approximation and closed-loop controller performance in the presence of Gaussian and non-Gaussian noise in the data set using physics-informed RNNs.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2025

A comparative TEA of a two-step process using chemical solvents for producing an ultra-sweet natural gas

Here, a comprehensive Techno-Economic Analysis (TEA) was performed to evaluate the economic feasibility of a novel two-step process (TSP) developed in Aspen Plus V12.1 to desulfurize and decarbonize a raw natural gas containing (2 mol% H 2 S and 5 mol% CO 2 ) into an ultra-sweet natural gas containing (1.72 ppmv H 2 S and 4.19 ppmv CO 2 ). The raw natural gas flow rate used in the TSP was 117.74 kg/s at 60 °C and 50 bar. The TSP combines an H 2 S desulfurization step using potassium carbonate (K 2 CO 3 ) and a CO 2 capture step using 3 different chemical solvents, monoethanolamine (MEA), sodium glycinate (SGS), and potassium glycinate (PGS). Both steps employ fixed-bed absorbers packed with Mellapak 250Y structured packing. The hydraulics and mass transfer characteristics for the TSP were calculated, indicating normal operation with higher gas-side (k G ) than liquid-side (k L ) mass transfer coefficients. The TEA of TSP indicated that PGS had the most promising economic feasibility among the 3 solvents as it exhibited the lowest Levelized Cost of CO 2 capture (LCOC) of $\$$47.54/ton.CO 2 at a Capital Expenditure (CAPEX) of $\$$24.98 million, and an Operating Expenditure (OPEX) of $\$$12.20 million/year. Also, the TSP could produce one MMSCF of ultra-sweet natural gas at a total cost of $\$$339.55.

03 NATURAL GAS↗

DOE OSTI2022

Model-based compositional predictions for a differential scanning calorimetry/thermogravimetric analysis-mass spectrometry system used for heat of vaporization measurements

A Differential Scanning Calorimetry/Thermogravimetric Analysis (DSC/TGA) procedure for determination of Heat of Vaporization (HOV) of fuel and surrogate fuel mixtures has been previously utilized for evaluation of oxygenate impacts on spark ignition fuels. This analysis has been further leveraged with mass spectrometry (MS) to elucidate vapor phase compositional changes during evaporation. In this study we focus on a simple system of three compounds (ethanol, n-hexane, and n-octane) to provide a model-based understanding of the evaporation process under these experimental conditions. An Aspen Plus model was set up to provide liquid and vapor phase concentration predictions during mixture evaporation using the initial mixture composition, and measured temperature and mass loss profiles from DSC/TGA experiments. Agreements between the trends of the MS ion count profiles and model composition predictions provide a degree of validation of this modeling approach that can allow the interpretation and extrapolation of DSC/TGA measurements for more complex fuel mixtures.

33 ADVANCED PROPULSION SYSTEMS↗

DOE OSTI2020

Levelized Cost of CO 2 Captured Using Five Physical Solvents in Pre-combustion Applications

Aspen Plus v8.8 was used to perform techno-economic analysis (TEA) of a CO 2 capture process from a typical fuel gas stream in a 543-MW pre-combustion power plant using five different physical solvents (Selexol, PEGPDMS-1, NMP, [aPy][Tf 2 N] and [hmim][Tf 2 N]). The process included a countercurrent packed-bed absorber operating under high-pressure over a wide range of temperatures and three pressure-swing flash drums for solvent regeneration. Furthermore, two packings, Mellapak 250Y and IMTP50, were used and the Levelized costs of CO 2 captured (LCOC) were calculated. The simulation results indicated that using Mellapak 250Y exhibited lower LCOC values than those when using IMTP50 for the five solvents under all conditions used as it offered better mass transfer. The CO 2 capture process carried out at low temperatures showed lower LCOC values than those at higher temperatures due to the increased CO 2 solubility in the solvents at lower temperatures, requiring smaller absorber diameter and lower solvent circulation rates, which offset the cooling requirements. Comparing the lowest LCOC values for the five solvents, the hydrophobic PEGPDMS-1 solvent was the most promising one compared to the other four solvents, due to its lowest capital and operating costs and noncorrosive, which enabled using less expensive materials for the process equipment.

42 ENGINEERING↗

DOE OSTI2021

Simulation of 12-bed vacuum pressure-swing adsorption for hydrogen separation from methanol-steam reforming off-gas

This study focuses on analysis of a 12-bed vacuum pressure-swing adsorption (VPSA) process capable of purifying hydrogen from a ternary mixture (H 2 /CO 2 /CO 75/24/1 mol%) derived from methanol-steam reforming. The process produces 9 kmol H 2 /h with less than 2 ppm and 0.2 ppm of CO2 and CO, respectively, to supply a polymer electrolyte membrane fuel cell. The process model is developed in Aspen Adsorption® using the “uni-bed” approach. A parametric study of H 2 purity and recovery with respect to adsorption pressure, adsorbent height, activated carbon:zeolite ratio, feed composition, and number of beds is performed. Results show 12-bed VPSA can meet the H 2 purity goals, with H 2 recovery as high as 75.75%. Adsorption occurs at 7 bar, the column height is 1.2 m, and the adsorbent ratio is 70%:30%. Furthermore, a 4-bed VPSA can achieve the same purity goals as the 12-bed process, but H 2 recovery decreases to 61.34%.

03 NATURAL GAS↗

DOE OSTI2021

The Inducible Accumulation of Cell Wall-Bound p -Hydroxybenzoates Is Involved in the Regulation of Gravitropic Response of Poplar

Lignin in Populus species is acylated with p-hydroxybenzoate. Monolignol p-hydroxybenzoyltransferase 1 (PHBMT1) mediates p-hydroxybenzoylation of sinapyl alcohol, eventually leading to the modification of syringyl lignin subunits. Angiosperm trees upon gravistimulation undergo the re-orientation of their growth along with the production of specialized secondary xylem, i.e., tension wood (TW), that generates tensile force to pull the inclined stem or leaning branch upward. Sporadic evidence suggests that angiosperm TW contains relatively a high percentage of syringyl lignin and lignin-bound p-hydroxybenzoate. However, whether such lignin modification plays a role in gravitropic response remains unclear. By imposing mechanical bending and/or gravitropic stimuli to the hybrid aspens in the wild type (WT), lignin p-hydroxybenzoate deficient, and p-hydroxybenzoate overproduction plants, we examined the responses of plants to gravitropic/mechanical stress and their cell wall composition changes. We revealed that mechanical bending or gravitropic stimulation not only induced the overproduction of crystalline cellulose fibers and increased the relative abundance of syringyl lignin, but also significantly induced the expression of PHBMT1 and the increased accumulation of p-hydroxybenzoates in TW. Furthermore, we found that although disturbing lignin-bound p-hydroxybenzoate accumulation in the PHBMT1 knockout and overexpression (OE) poplars did not affect the major chemical composition shifts of the cell walls in their TW as occurred in the WT plants, depletion of p-hydroxybenzoates intensified the gravitropic curving of the plantlets in response to gravistimulation, evident with the enhanced stem secant bending angle. By contrast, hyperaccumulation of p-hydroxybenzoates mitigated gravitropic response. These data suggest that PHBMT1-mediated lignin modification is involved in the regulation of poplar gravitropic response and, likely by compromising gravitropism and/or enhancing autotropism, negatively coordinates the action of TW cellulose fibers to control the poplar wood deformation and plant growth.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2021

Kraft black liquor concentration with graphene oxide membranes: Process simulations and technoeconomic analysis

Abstract Black liquor (BL) dewatering by multi‐effect evaporation in the kraft papermaking process is highly energy‐intensive. It was previously shown that graphene oxide (GO) nanofiltration membranes can remove lignin, other organics, and inorganic salts from BL while exhibiting stability in caustic BL conditions. Here, we design and simulate several candidate dewatering processes and evaluate their technoeconomic characteristics. All processes concentrate BL from 15 to 30 wt% solutes while producing aqueous permeate. Two process options were analyzed—option A including “last‐mile” permeate treatment to reduce solutes to 0.2 wt%, and option B excluding this treatment and producing a 3–4 wt% solutes stream. These processes were simulated in custom‐built ASPEN Plus flowsheets interfaced with Microsoft Excel and MATLAB. All processes deliver large (>40%) energy savings. Detailed technoeconomic analysis showed that option A processes are profitable in mills equipped with condensing turbines, but unprofitable with only purchased fuel savings. Option B processes are profitable in both situations, but require the caustic permeate to be utilized in other kraft process units. They are also profitable with electricity generation when operated at smaller scales matching the requirements of other process units. Monte‐Carlo sensitivity analysis shows that Option A can yield median 20‐year NPVs up to ~$10MM and Option B up to ~$25MM. Overall, GO membrane‐based BL dewatering is economically promising, assuming successful slipstream piloting and scale‐up campaigns. It would have immediate sustainability benefits from large energy savings, and broader implications for biorefinery processes due to the ability to fractionate biomass feedstock components under harsh conditions.

Wang, Zhongzhen↗

DOE OSTI2022

A separations and purification process for improving yields and meeting fuel contaminant specifications for high-octane gasoline produced from dimethyl-ether over a Cu/BEA catalyst

In this work, we have been developing a three-step conversion of biomass-derived syngas to methanol to dimethyl-ether (DME) to non-aromatic hydrocarbons for use as high-octane gasoline and sustainable aviation fuel. This process produces branched alkanes from DME using a Cu/BEA catalyst and is a promising alternative to other syngas conversion processes such as Fischer-Tropsch to linear alkanes and traditional ZSM-5 catalyzed methanol to aromatic gasoline. In this short article we describe some advances in our understanding related to separations and purification via the use of more detailed experimental speciation in an updated process model involving multiple phase equilibrium-based separation steps. Primary modeled reactor outlet constituents (and weight %) are: C3 and lighter hydrocarbon gases (11.1%), C4s (54.5%), H 2 (1.2%), CO 2 (2.9%), water (5.0%), unreacted DME (16.5%), methanol (2.3%), and C5+ hydrocarbons (6.4%). DME (the primary reactant) and H 2 recycle and reuse are important for the overall process efficiency, and the recycle of C4s is important to increase the C5+ yield via reactivation and homologation. Thus H 2 , C4s, and DME are targeted for recycle, while methanol and water need to be removed from the product to conform with fuel specifications. Model predictions from Aspen Plus using the NRTL-RK property method indicate a fuel composition with C5+ content of 97.1 wt%, with minor constituents: 2.4 wt% C4s, 0.3 wt% methanol, 0.1 wt% DME, 0.03 wt% water, and 0.01 wt% C3s. These ranges of minor components conform with fuel quality requirements, and the modeled product is amenable for unconstrained blending to boost gasoline octane ratings.

09 BIOMASS FUELS↗

DOE OSTI2021

Disturbance-accelerated succession increases the production of a temperate forest

Many secondary deciduous forests of eastern North America are approaching a transition in which maturing early successional tree species are declining, resulting in an uncertain future for these forests’ century-long carbon (C) sink. We initiated the Forest Accelerated Succession Experiment (FASET) at the University of Michigan Biological Station to examine the patterns and mechanisms underlying forest C cycling following the stem-girdling induced mortality of >6,700 early successional Populus spp. (aspen) and Betula papyrifera (paper birch). Since 2008, meteorological flux tower-based C cycling observations from the 33-ha treatment forest have been paired with those from a nearby unmanipulated forest. Following over a decade of observations, herein we revisit our core hypothesis: that net ecosystem production (NEP) would increase following the transition to mid-late successional species dominance due to increased canopy structural complexity. Supporting our hypothesis, NEP was stable, briefly declined, and then increased relative to the control in the decade following disturbance; however, increasing NEP was not associated with rising structural complexity but rather the rapid 1-year recovery of total LAI as mid-late successional Acer, Quercus, and Pinus assumed canopy dominance. The transition to mid-late successional species dominance improved carbon-use efficiency (CUE = NEP/gross primary production) as ecosystem respiration declined. Similar soil respiration rates in control and treatment forests, along with species differences in leaf physiology and the rising relative growth rates of mid-late successional species in the treatment forest, suggest changes in aboveground plant respiration and growth, respectively, were primarily responsible for increases in NEP. We conclude that deciduous forests transitioning from early to middle succession are capable of sustained or increased NEP, even when experiencing extensive tree mortality. This adds to mounting evidence that aging deciduous forests in the region will function as C sinks for decades to come.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2021

Noise Robustness and Experimental Demonstration of a Quantum Generative Adversarial Network for Continuous Distributions

Abstract The potential advantage of machine learning in quantum computers is a topic of intense discussion in the literature. Theoretical, numerical, and experimental explorations will most likely be required to understand its power. There have been different algorithms proposed to exploit the probabilistic nature of variational quantum circuits for generative modeling. In this paper, a hybrid architecture for quantum generative adversarial networks (QGANs) is employed and their robustness in the presence of noise is studied. A simple way of adding different types of noise to the quantum generator circuit is devised, and the noisy hybrid QGANs (HQGANs) are simulated numerically to learn continuous probability distributions, and to show that the performance of HQGANs remains unaffected. The effect of different parameters on the training time is also investigated to reduce the computational scaling of the algorithm and simplify its deployment on a quantum computer. The training on Rigetti's Aspen‐4‐2Q‐A quantum processing unit is then performed, and the results from the training are presented. The authors' results pave the way for experimental exploration of different quantum machine learning algorithms on noisy intermediate‐scale quantum devices.

Anand, Abhinav↗

DOE OSTI2023

Techno-economic and life cycle analyses for a supercritical biodiesel production process from waste cooking oil for a plant located in the Midwest United States

Existing literature lacks detailed techno-economic and environmental life cycle analyses (TEA-LCA) focused on supercritical biodiesel production pathways produced via waste products. Therefore, in this work, the TEA-LCA was conducted to generate supercritical biodiesel from waste cooking oil for plants located in the Midwest region of USA having annual production capacities of 10,600 and 128,000 t using Aspen Plus and GREET softwares. Here, two plant production capacities were chosen to capture the economies of scale impact on biodiesel manufacture cost. In the supercritical process, methanol and propane were used as a cosolvent to synthesize biodiesel from waste cooking oil (WCO) at 280 °C and 128 bar at a residence time of 8.4 min and a WCO conversion rate of 97%. Economic analysis revealed that the supercritical process was an economically attractive pathway with a 2-year payback period for the 10,600 t/year capacity along with a break-even selling price of $\$$ 2.42/gal of diesel. In case of the larger plant (128,000 t/year capacity), the payback period and the breakeven selling price were considerably lower at values of 0.4 years and $1.31/gal of diesel, respectively, due to economies of scale impact. The generated biodiesel from supercritical process for the both the plant capacities met European (EN14214) and US (ASTM D6751) fuel quality standards while the obtained commercially valuable side product, i.e., glycerol, adhered to a pharmaceutical grade of 99.7%. Cradle to gate life cycle analysis using GREET revealed that supercritical process possessed 17% lower CO2 emissions than alkali-catalyzed process and 4% lower CO2 emissions than the conventional diesel production process. Other biodiesel production pathways in the literature were also compared to the results of the TEA-LCA of supercritical biodiesel production pathway.

Biodiesel production↗

DOE OSTI2020

Techno-economic prospects for producing Fischer-Tropsch jet fuel and electricity from lignite and woody biomass with CO 2 capture for EOR

This work explores the prospective techno-economic performance of facilities that produce low- and net-negative-carbon liquid transportation fuels and electricity with CO 2 capture for enhanced oil recovery. The lignite and biomass-to-jet fuel process is based on KBR’s TRIG gasifier, Rectisol (for sulfur removal and CO 2 capture), fixed-bed low temperature Fischer-Tropsch synthesis of liquid fuels, and Brayton/Rankine combined cycles to convert synthesis/refining off-gases and waste heat to electricity. This work leverages a recent, highly-detailed assessment of a prospective first-of-a-kind (FOAK) demonstration facility to develop highly detailed Aspen Plus process simulations for nine prospective N th -of-a-kind (NOAK) plant equipment configurations. Component-level capital costs from the FOAK study are scaled and adjusted to reflective prospective learning-by-doing to estimate capital costs for the NOAK designs. NOAK plant economic performance is found to be largely insensitive to variations in plant configurations and electricity output fraction, but biomass input fraction significantly affects profitability. Facilities that consume only carbon–neutral biomass, with no lignite co-feed, have significantly net-negative carbon emissions and the most favorable prospective economics when carbon emissions are priced. For these facilities, the crude oil price required for plant economic viability falls rapidly from $\$$100/bbl as carbon emission prices increase above $\$$120/tonne CO 2eq . In general, plants that co-fire lignite with biomass are less profitable (than 100% biomass plants) due to their higher net greenhouse gas emissions.

09 BIOMASS FUELS↗

DOE OSTI2022

Static and dynamic modeling of steam integration for a NuScale small modular reactor and pulp and paper mill coupling for carbon-neutral manufacturing

Small modular reactors (SMRs) are reactor designs producing less than 300 MWe and are generally planned for deployment as multimodule nuclear power plants. The possibility of factory-manufactured, flexibly sized plants expands the opportunities for nuclear power to different communities and industries, including manufacturing plants that currently utilize fossil fuels to produce both steam and electricity. This paper examines the feasibility of coupling a NuScale SMR with a midsize pulp and paper mill in the Southeastern United States. A steady-state mill model was developed in Aspen HYSYS, based on real data from the operation of the mill, and modified it to include the SMR while maintaining steam quality requirements and making as few changes as possible to existing equipment. Dynamic plant models were also developed Dymola to demonstrate possible plant conditions, using three configurations. Preliminary results suggest that, while SMR coupling is physically feasible, its economic feasibility is limited by the differences in steam and electricity demands. Because of limitations in the amount of steam the mill can take from the SMR, sizing the SMR for the plant’s steam demand may result in an electricity deficit, or vice versa. Furthermore, dynamic analyses show that the addition of a thermal storage system could reduce such deficits, but this entails its own challenges. Each plant must determine the best configuration and control scheme for itself, based on its electricity and heat needs, including the peak duration and intensity for both. Ultimately, an implementation of SMRs with manufacturing processes would benefit from partnering with a local utility to purchase excess electricity generated by the SMR. This will help manufacturing facilities meet their environmental and cost-savings goals, in addition to meeting the need for cost-effective baseload power across the United States.

03 NATURAL GAS↗