Results for “ARC welding” — Page 4

DOE OSTI2022

Fusion welding of refractory metals and ZrB 2 -SiC-ZrC ceramics

Molybdenum and a molybdenum alloy were fusion welded to ZrB2-based ceramics to determine if the electrical and thermal properties of the metals and ceramics affected their weldability. Commercial ceramic powders were hot pressed, machined into coupons, and preheated to 1600 °C before joining the ceramics to commercial metals using plasma arc welding. Weldability varied as indicated by the range of porosity observed within the fusion zones. Measured thermal and electrical properties appeared to have little to no effect on the weldability of metal-ceramic welds despite the large range of values measured across each property. Differences in melting temperatures between metal and ceramic coupons did affect weldability by changing the weld penetration depth into ceramic coupons. Finally, future studies on metal-ceramic welds are suggested to investigate the effect that work function, melt viscosity, wetting, or other properties have on weldability.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Fabrication and Testing of DOE Standard Canister Closure Leak Test Assembly

DOE manages over 300 types of spent nuclear fuel (SNF), many of which are located at the Idaho National Laboratory (INL) site. Managing this large variety of SNF for storage, transportation, and disposal poses a challenge to DOE. The Idaho Cleanup Project and INL are collaborating on the DOE SNF Road-Ready Demonstration (“Road-Ready Demonstration”), which will develop and demonstrate the designs, technology, processes, and regulatory framework for packaging DOE-managed SNF for “road-ready dry storage.” Road-ready dry storage is an SNF management concept in which SNF is packaged into dry, sealed canisters that are then placed in onsite storage in anticipation of later transport and disposition. The forward-looking goal of the Road-Ready Demonstration is to establish the foundation for a large-scale road-ready dry storage program at the INL site. In support of establishing a large-scale road-ready dry storage program at the INL site, the Road-Ready Demonstration will first package Fort St. Vrain SNF currently in dry storage at INL into several DOE Standard Canisters (DOESCs). These DOESCs will in turn be loaded into another containment similar to commercial multi-purpose canisters. This multi-purpose canister will then be compatible with a transportation or storage system, such as a storage cask for interim storage or transportation package for offsite transport. These DOESCs will remain sealed over the course of their storage, transportation, and applicable disposal functions. The closure process for the DOESC will include fuel and basket loading, welding, inspection, leak testing, and, if needed, repair. As a follow-up to previous discussions on the design of the DOE Closure Leak Test Assembly (LTA), this report describes recent fabrication and testing efforts performed at INL. DOESCs are sealed by two sequential gas tungsten arc welds, both of which are performed by remotely operated and semiautomatic welding systems. The first weld is a circumferential pipe weld that completes the assembly of the canister body and lid assembly. The second and final closure weld attaches the vent plug to the vent socket via a butt joint. After the second weld is performed, the welds are helium leak tested using an evacuated envelope technique. The LTA was designed for both remote and manual operation. This report describes the fabrication and performance testing associated with the evacuated envelope technique. INL staff designed, fabricated, and tested the LTA at INL facilities. This testing included establishing technique and system sensitivities in accordance with ASME and American National Standards Institute N14.5 requirements. Forthcoming work will cover such areas as design optimization, process and personnel qualification, and implementation in Road-Ready Demonstration operations.

42 ENGINEERING↗

DOE OSTI2023

Fabrication and Testing of DOE Standard Canister Closure Leak Test Assembly – 24139

DOE manages over 300 types of spent nuclear fuel (SNF), many of which are located at the Idaho National Laboratory (INL) site. Managing this large variety of SNF for storage, transportation, and disposal poses a challenge to DOE. The Idaho Cleanup Project and INL are collaborating on the DOE SNF Road-Ready Demonstration (“Road-Ready Demonstration”), which will develop and demonstrate the designs, technology, processes, and regulatory framework for packaging DOE-managed SNF for “road-ready dry storage.” Road-ready dry storage is an SNF management concept in which SNF is packaged into dry, sealed canisters that are then placed in onsite storage in anticipation of later transport and disposition. The forward-looking goal of the Road-Ready Demonstration is to establish the foundation for a large-scale road-ready dry storage program at the INL site. In support of establishing a large-scale road-ready dry storage program at the INL site, the Road-Ready Demonstration will first package Fort St. Vrain SNF currently in dry storage at INL into several DOE Standard Canisters (DOESCs). These DOESCs will in turn be loaded into another containment similar to commercial multi-purpose canisters. This multi-purpose canister will then be compatible with a transportation or storage system, such as a storage cask for interim storage or transportation package for offsite transport. These DOESCs will remain sealed over the course of their storage, transportation, and applicable disposal functions. The closure process for the DOESC will include fuel and basket loading, welding, inspection, leak testing, and, if needed, repair. As a follow-up to previous discussions on the design of the DOE Closure Leak Test Assembly (LTA), this report describes recent fabrication and testing efforts performed at INL. DOESCs are sealed by two sequential gas tungsten arc welds, both of which are performed by remotely operated and semiautomatic welding systems. The first weld is a circumferential pipe weld that completes the assembly of the canister body and lid assembly. The second and final closure weld attaches the vent plug to the vent socket via a butt joint. After the second weld is performed, the welds are helium leak tested using an evacuated envelope technique. The LTA was designed for both remote and manual operation. This report describes the fabrication and performance testing associated with the evacuated envelope technique. INL staff designed, fabricated, and tested the LTA at INL facilities. This testing included establishing technique and system sensitivities in accordance with ASME and American National Standards Institute N14.5 requirements. Forthcoming work will cover such areas as design optimization, process and personnel qualification, and implementation in Road-Ready Demonstration operations.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2024

Fabrication and Testing of DOE Standard Canister Closure Leak Test Assembly

DOE manages over 300 types of SNF, most of which are located at the INL site. “Road-ready dry storage” is a management concept where SNF is packaged into dry, sealed canisters, which are then placed in on-site storage in anticipation of later removal. The Idaho Cleanup Project and INL are collaborating on the Road-Ready Capability Demonstration Project, which will develop and demonstrate the designs, technology, processes, and regulatory framework for packaging DOE SNF for road-ready dry storage. In support of establishing a large-scale road-ready dry storage program at the INL site, the demonstration will package a select amount of DOE-managed SNF into DOE Standard Canisters. The closure process for the DOE Standard Canisters will include fuel and basket loading, welding, inspection, leak testing, and if needed, repair. As a follow-up to previous discussion on the design of the DOE Closure Leak Test Assembly, this report describes recent fabrication and testing efforts performed at INL. DOE Standard Canisters are sealed by two sequential gas tungsten arc welds. Both are performed by remotely operated and semi-autonomous welding systems. The first weld is a circumferential pipe weld that completes assembly of the canister body and lid assembly. The second and final closure weld connects the vent plug to the vent port with an identical butt joint to the circumferential pipe weld. After the second weld is performed on the vent port, these welds are helium leak tested using an inside-out technique. In addition to the commercially available vacuum and leak detector systems, the DOE Standard Canister Closure Leak Test Assembly was designed for both remote and manual operation. This report describes fabrication and performance testing associated with the inside-out technique. INL staff designed and tested systems to accomplish these tasks. Hardware fabrication occurred at INL facilities. Forthcoming work includes design optimization, integration to existing systems, and implementation to packaging demonstration operations.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2020

Modular In-Chamber Electron Beam Welding – Process Planning: Welding, Cladding, Inspection, and Manufacturing

Electron beam welding (EBW) is commonly employed by industry today to join relatively thin section components. Industrial sectors which utilize the technology include; automotive, aircraft, aerospace, defense, medical, oil & gas, etc. The ability to produce single pass, thick section (up to 6 inches, 150mm) welds has also been available for more than 40 years; however, the technology has not been deployed for civil nuclear manufacturing and fabrication such as reactor pressure vessels, steam generators, or pressurizers. Instead, thick section joining is performed much in the same manner it has been for decades using submerged arc or gas tungsten arc welding processes. Recent research performed under U.S. Department of Energy (DOE) project DE-NE0008629 has demonstrated that the overall welding time to produce one major reactor pressure vessel (RPV) girth weld can be reduced from weeks to less than 90 minutes, while maintaining exceptional quality and inspection characteristics. The subject project (DE-NE0008846) investigates a modular in-chamber (MIC) EBW approach which allows various RPV sections to be joined within a “modular” chamber. The MIC-EBW approach utilizes individual modules that can be stacked and de-stacked to various heights to enable production girth welds to be performed at a given elevation. This report describes the various processing methodology necessary to complete major girth weldments for the NuScale Power small modular reactor including welding development, manufacturing, production sequence, inspection, and cladding.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

DOE OSTI2021

Large-Scale Welding Process Simulation by GPU Parallelized Computing

The computational design of industrially relevant welded structures is extremely time consuming due to coupled physics and high nonlinearity. Previously, most welding distortion and residual stress simulations have been limited to small coupons and reduced order (from three-dimensional [3D] to two-dimensional [2D]), or inherent strain approximations were used for large structures. In this current study, an explicit finite element code based on a graphics processing unit was utilized to perform 3D transient thermomechanical simulation of structural components during welding. Laser brazing of aluminum alloy panels as representative of automotive manufacturing scenarios was simulated to predict out-of-plane distortion under different clamping conditions. The predicted deformation pattern and magnitude were validated by laser scanning data of physical assemblies. In addition, the code was used to investigate residual stresses developed during multipass arc welding of a nuclear industry pressurizer surge nozzle and subsequent welding repair where a 3D simulation was necessary. Taking the experimental data as reference, the 3D model predicted better residual stress distribution than a typical 2D asymmetrical model. Stress evolution in welding repair was also presented and discussed in this study. Furthermore, the efficient numerical model made it feasible to use integrated computational welding engineering to simulate welding processes for large-scale structures.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2023

Defect Recognition for Eddy Current Testing of Spent Nuclear Fuel Canister using Convolutional Neural Network

This paper proposes an accurate and robust defect detection solution for 304L and 306L stainless steel (SS) weld. In the proposed solution, Eddy current testing (ECT) is employed to generate 2-dimensional (2D) data for samples under test with defects. The 2D data can be treated as images for deep learning-based defect detection. Since convolutional neural networks (CNNs) are powerful in processing images, CNN is employed in this study for defect detection. Experiments are conducted on a submerged arc welding (SAW) 304L SS weld sample with an artificial crack generated by waterjet cutting. The ECT data on this seeded fault sample is utilized to verify the proposed solution. For this purpose, the ECT measurement are separated as from Fault area and Normal area, which are used for CNN training. After training, the testing data is used for verification. Experimental results demonstrate the feasibility and effectiveness of the proposed solution.

Niu, Guangxing↗

DOE OSTI2025

Characterization of Build Parameters and Microstructure in Low Heat Input WAAM of Ni-Based Superalloy Haynes 282

Ni-based superalloy Haynes® 282® is being targeted for various applications in advanced power generation systems for its superior fabricability, weldability, and excellent high temperature creep and corrosion performance. This process optimization study aims to use a low heat-input, high deposition rate, controlled Gas Metal Arc Welding (GMAW) process, Cold Metal Transfer (CMT) by Fronius, attempting to achieve fully dense fabrication and possibly avoid the need for HIP. Twenty-one multilayer blocks (~25x100x40 mm3) were deposited to explore a large set of build parameters variations that focused on varying the travel speed from 14 to 42 inches per minute (ipm) and wire feed speed from 150 to 450 ipm. A strong correlation has been observed between arc energy – controlled primarily by travel and wire feed speed. Initial visual inspection, internal microstructural examination, and computed tomography (CT) have been used to determine the effects of built parameters on evolution of internal porosity and defects. Scanning electron microscopy techniques enabled structural and compositional imaging of heterogeneity and changes in microstructural properties.

additive manufacturing↗

DOE OSTI2025

Characterization of Build Parameters and Microstructure in Low Heat Input WAAM of Ni-Based Superalloy Haynes 282

Ni-based superalloy Haynes® 282® is being targeted for various applications in advanced power generation systems for its superior fabricability, weldability, and excellent high temperature creep and corrosion performance. This process optimization study aims to use a low heat-input, high deposition rate, controlled Gas Metal Arc Welding (GMAW) process, Cold Metal Transfer (CMT) by Fronius, attempting to achieve fully dense fabrication and possibly avoid the need for HIP. Twenty-one multilayer blocks (~25x100x40 mm3) were deposited to explore a large set of build parameters variations that focused on varying the travel speed from 14 to 42 inches per minute (ipm) and wire feed speed from 150 to 450 ipm. A strong correlation has been observed between arc energy – controlled primarily by travel and wire feed speed. Initial visual inspection, internal microstructural examination, and computed tomography (CT) have been used to determine the effects of built parameters on evolution of internal porosity and defects. Scanning electron microscopy techniques enabled structural and compositional imaging of heterogeneity and changes in microstructural properties.

additive manufacturing↗

DOE OSTI2022

Material Characterization of Grade 91 Steel Welds using, Micro-resolution Ultrasonic Imaging System

Grade 91 (9Cr-1Mo-V) steel is a common structural material for fossil-fuel fired and nuclear power plants because of its creep strength and oxidation resistance at high temperatures. In this research, we studied the feasibility of correlating the high-resolution images obtained from the immersion ultrasonic imaging technique to microstructure regions in Grade 91 steel plate weldments. The high-resolution ultrasonic images presented in this paper were generated using a 20-MHz focused transducer as the transmitter, and a laser vibrometer as the receiver in the through transmission configuration to produce longitudinal and shear waves. This nondestructive evaluation (NDE) method was used to identify the Fusion Zone (FZ), Heat-Affected Zone (HAZ), and Base Metal (BM) regions of Grade 91 cold metal transfer (CMT) and flux core arc welds (FCAW). The ultrasonic imaging results were analyzed using beam propagation amplitudes and homogeneity, which in turn were used to relate the different microstructure regions of the FCAW and CMT welded samples. With this study, we were able to identify highly susceptible microstructures in the weld that could potentially promote creep type failures.

20 FOSSIL-FUELED POWER PLANTS↗

DOE OSTI2022

Optimizing Multi-Robot Placements for Wire Arc Additive Manufacturing

Wire arc additive manufacturing is a metal additive manufacturing process in which the material is deposited using arc welding technology. It is gaining popularity due to high material deposition rates and faster build time. It is en-abled using robotic manipulators and can build relatively large-scale parts faster when compared with other metal additive manufacturing processes. However, the size of the large-scale parts is limited by the size of the industrial manipulator being used for the process. This limitation is overcome by using a fixed configuration multi-robot cell in which manipulators work cooperatively to build large-scale parts quickly. A fixed multi-robot cell with closely spaced industrial manipulators has high flexibility, but it restricts the part size that can be built. If the manipulators are spread out, the cell loses its flexibility but can build relatively larger parts. This issue can be avoided by using larger size manipulators, which are expensive, or by moving the modest size manipulators based on the part geometries. This paper presents a novel algorithm to generate multi-robot placements for different part geometries to be built using wire arc additive manufacturing. Furthermore, the algorithm hierarchically optimizes the build time and the inverse kinematics consistency in robot paths to improve the process efficiency and part quality. We compare the results with fixed multi-robot cells and provide insights to users to make an informed decision on whether to use a fixed or a flexible multi-robot cell for wire arc additive manufacturing.

Bhatt, Prahar↗

DOE OSTI2022

Additive Manufacture of Multi-Functional, Large-Scale Components

The poster summarizes the main results for a LDRD focused on developing a arc-based additive manufacturing (AM) system capable of fabricating large components with a composition gradient otherwise known as functionally graded materials (FGMs). FGMs are capable of addressing local extreme conditions in an optimal and cost-effective manner. The AM system (referred to as multi-Wire Arc Additive Manufacturing or m-WAAM) consisted of modifying a standard automated gas tungsten arc welding system to deliver multiple welding wires to the weld pool at controlled rates to deposit desired alloy compositions at critical locations. Numerous shapes and composition gradients were fabricated with the system and the effect of various deposition parameters on the nature of the composition profile were evaluated. Additionally, heat treatment of the FGM was performed to develop graded microstructures which should enhance dynamic impact performance of inexpensive steels. The project highlights the potential of m-WAAM to efficiently fabricate FGMs. However, this project only explored the science behind the technique and additional development work will be required to develop a fully-functional system that can build more complex components.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Electroslag additive manufacturing: A pathway for high throughput near net shape production

Electroslag Additive Manufacturing (ESAM), a new high-throughput additive manufacturing (AM) method that combines Electroslag Strip Cladding (ESC) and wire arc AM (WAAM) is introduced. This combination enables the high deposition rate of ESC (more than 20 kg/h with a 60 mm strip electrode) to benefit from the precise geometric control of WAAM. As a precursor to ESAM, the ESC process is investigated in an AM context independently by evaluating both direct and staggered bead-stacking strategies and analyzing the microstructural and mechanical properties of each. This is followed by an ESAM demonstration producing an annular geometry by pairing ESC with gas tungsten arc welding (GTAW), wherein GTAW is utilized to construct annular walls that are subsequently infilled via ESC. The microstructure and mechanical properties of ESC-only AM are compared with that of the ESAM method and it is shown that printed integral retaining walls do not impact the resulting mechanical properties of ESAM. Furthermore, results indicate that ESAM-produced Alloy 625 parts exhibit tensile properties on par with cast counterparts, supporting the method’s scalability to components exceeding one metric ton, and possibly making ESAM a viable future manufacturing approach for competitive production of large-scale components currently manufactured by casting and forging.

Additive manufacturing↗

DOE OSTI2020

Laser powder bed fusion of Inconel 718 on 316 stainless steel

The joining of Inconel 718 and 316 stainless steel has notable industrial importance. However, traditional arc-welding has many issues. In particular, the formation of the detrimental Nb-rich Laves phase in the heat affected zone can promote crack initiation and propagation, which leads to poor mechanical properties. The small heat input and the rapid solidification of laser powder bed fusion (PBF) has the potential to suppress this problem. Despite the infancy of the multi-material PBF, it is of interest to investigate the relationship among the process parameter, the microstructure at the materials joining point, and the mechanical performance. In this study, we used high-speed x-ray imaging to in-situ monitor the printing of Inconel 718 tracks on a 316H SS substrate via laser powder bed fusion, followed by post-build characterization and testing with SEM, XRD and nanoindentation. We observed that a higher linear energy density resulted in a more diffused interface and a smaller compositional gradient, but as a trade-off, generated more keyhole pores and thermal cracks. Furthermore, we also showed that the built layer exhibited chemical inhomogeneity at two length scales: a tens-of-mu m-scale compositional vortex due to the melt flow, and a sub-mu m-scale Nb-rich dendritic structure due to the non-equilibrium solidification that led to the formation of the Laves phase. It was inferred that the chemical inhomogeneity may benefit the mechanical properties at the interface by providing more interlocking between the two materials and also by limiting the effect of the brittle Laves phase to potentially short range.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Material properties and mechanical behaviour of functionally graded steel produced by wire-arc additive manufacturing

Metal Big Area Additive Manufacturing is an additive manufacturing technique based on Gas Metal Arc Welding (GMAW) with the option to use many shielding gases, and materials. The system is equipped with a dual torch design allowing for printing different materials; in our study, AISI 410 stainless steel and AWS ER70S-6 mild steel are both printed in the same component. Different print strategies were designed to highlight changes in material and mechanical properties. Deformation behaviour of a materials’ interface was analysed by two-dimensional digital image correlation of uniaxial tensile specimens in displacement-controlled tests. Instances of non-homogeneous local strains adjacent to the interface are observed, as well as variability in mechanical behaviour and microstructure based on location within the print. Optical and electron microscopy are used to evaluate three microstructural zones in a 5 mm range of the interface between mild steel and stainless steel. Areas far from the interface produced polygonal ferrite and pearlite, while areas close to the interface produced acicular ferrite and bainite. Chromium redistribution profiles are dependent on the print strategy used, as shown by scanning electron microscopy with Energy dispersive spectroscopy. Evidence produced via electron backscatter diffraction is shown to support the argument that transformation induced plasticity is not the cause for the non-homogeneous deformation.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Stress corrosion cracking mechanism of cold spray coating on a galvanically similar substrate

Here, the chloride-induced stress corrosion cracking (CISCC) mechanism of cold spray (CS) coating on a galvanically similar substrate is investigated. Arc welded 304L stainless steel (SS) specimens are loaded into four-point bend fixtures, cold sprayed with 304L SS, then immersed in boiling MgCl 2 . Interconnected porosity forms through crevice corrosion along CS splat boundaries, allowing corrosive species to penetrate through the CS layer. Nevertheless, the substrate is resistant to CISCC likely because of compressive stress introduced by peening during CS particle impacts. These findings underscore the importance of residual stress in the environmental degradation of CS coatings or repairs of engineering structures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2026

Strain age cracking in a simulated heat affected zone of Inconel 740H laser-powder bed fusion components

Inconel® 740H components produced via laser-powder-bed fusion (L-PBF) additive manufacturing are ideal for supercritical CO2 primary heat exchangers. Arc welding is often needed, and subsequent post-weld heat treatment aging at 790–840 °C is required to improve strength via gamma prime (γ’) precipitation; however, strain age cracking (SAC) can occur in the heat affected zone (HAZ) during this process. This study uses stress relaxation testing at 800 °C on simulated HAZ specimens from vertically and horizontally built L-PBF IN740H to assess SAC susceptibility across heating rates of 40–3480 °C/h and weld-induced strains of 3–10 %. Vertical builds require greater mechanical energy input and exhibit longer times to fracture than horizontal builds, and time to fracture occurs sooner at slower heating rates. Creep voids were observed in γ’-denuded regions along grain boundaries, and cracking propagated along migrated grain boundaries and at interfaces between elongated secondary phases (γ’ or carbides) and the γ-matrix.

14 SOLAR ENERGY↗

DOE OSTI2024

Reduction kinetics of hematite powder using argon/hydrogen plasma with prospects for near net shaping of sustainable iron

Direct reduction of iron ore using hydrogen plasma is being explored as a potential solution to decarbonize the iron and steel sector. The current state-of-the-art demonstrated reduction of hematite pellets via hydrogen plasma using Ar + 10% H 2 but had slow reduction kinetics, requiring 30 minutes of plasma exposure for complete reduction. Here we show that using hematite in a powder form, easily obtainable from beneficiated ore, results in 10× faster kinetics using plasma generated from Ar + 2% H 2 shielding gas compared to the current state-of-the art. Additionally, the increased kinetics using powders and a dilute hydrogen concentration can enable the use of advanced manufacturing techniques like blown powder directed energy deposition using a plasma tungsten arc welding torch to manufacture near net shape components directly from the ore concentrates. This ore to part approach will also reduce the emissions associated with downstream processes like rolling, forging, and machining, thereby further aiding in the sectorial decarbonization efforts.

36 MATERIALS SCIENCE↗