Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “vertical axis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Room temperature multiferroicity and magnetodielectric coupling in 0–3 composite thin films

Magnetoelectric (ME) composite thin films are promising candidates for novel applications in future nanoelectronics, spintronics, memory and other multifunctional devices as they exhibit much higher ME coupling and transition temperatures (Tc) than well-known single phase multiferroics discovered to date. Among the three types of multiferroic composite nanostructures, (2-2) layered and (1-3) vertically aligned composite nanostructures exhibit comparatively smaller ME coupling due to different shortcomings which restrict their use in many applications. Here we study the morphological, piezoresponse force microscopic (PFM), ferroelectric, magnetic, and magnetodielectric properties of 0-3 (magnetic nanoparticles (0) homogeneously distributed in ferroelectric matrices (3)) multiferroic composite thin films. The Pb(Fe 0.5 Nb 0.5 )O 3 (PFN) - Ni 0.65 Zn 0.35 Fe 2 O 4 (NZFO) particulate composite films were synthesized by pulsed laser deposition (PLD). These particulate composite thin films are completely c-axis oriented with very low surface roughness. We observed magnetic and ferroelectric T c above room temperature (RT) for all composite thin films. The PFN-NZFO 0-3 composites exhibit large polarization, high saturated magnetization with low coercive field, low dielectric loss along with magnetodielectric coupling at RT. These nanocomposites might be utilized in next generation nano/microelectronics and spintronic devices.

36 MATERIALS SCIENCE↗
NASA NTRS2011

Excitation of a Parallel Plate Waveguide by an Array of Rectangular Waveguides

This work addresses the problem of excitation of a parallel plate waveguide by an array of rectangular waveguides that arises in applications such as the continuous transverse stub (CTS) antenna and dual-polarized parabolic cylindrical reflector antennas excited by a scanning line source. In order to design the junction region between the parallel plate waveguide and the linear array of rectangular waveguides, waveguide sizes have to be chosen so that the input match is adequate for the range of scan angles for both polarizations. Electromagnetic wave scattered by the junction of a parallel plate waveguide by an array of rectangular waveguides is analyzed by formulating coupled integral equations for the aperture electric field at the junction. The integral equations are solved by the method of moments. In order to make the computational process efficient and accurate, the method of weighted averaging was used to evaluate rapidly oscillating integrals encountered in the moment matrix. In addition, the real axis spectral integral is evaluated in a deformed contour for speed and accuracy. The MoM results for a large finite array have been validated by comparing its reflection coefficients with corresponding results for an infinite array generated by the commercial finite element code, HFSS. Once the aperture electric field is determined by MoM, the input reflection coefficients at each waveguide port, and coupling for each polarization over the range of useful scan angles, are easily obtained. Results for the input impedance and coupling characteristics for both the vertical and horizontal polarizations are presented over a range of scan angles. It is shown that the scan range is limited to about 35 for both polarizations and therefore the optimum waveguide is a square of size equal to about 0.62 free space wavelength.

Rengarajan, Sembiam↗
NASA NTRS1993

Estimating the path-average rainwater content and updraft speed along a microwave link

There is a scarcity of methods for accurately estimating the mass of rainwater rather than its flux. A recently proposed technique uses the difference between the observed rates of attenuation A with increasing distance at 38 and 25 GHz, A(38-25), to estimate the rainwater content W. Unfortunately, this approach is still somewhat sensitive to the form of the drop-size distribution. An alternative proposed here uses the ratio A38/A25 to estimate the mass-weighted average raindrop size Dm. Rainwater content is then estimated from measurements of polarization propagation differential phase shift (Phi-DP) divided by (1-R), where R is the mass-weighted mean axis ratio of the raindrops computed from Dm. This paper investigates these two water-content estimators using results from a numerical simulation of observations along a microwave link. From these calculations, it appears that the combination (R, Phi-DP) produces more accurate estimates of W than does A38-25. In addition, by combining microwave estimates of W and the rate of rainfall in still air with the mass-weighted mean terminal fall speed derived using A38/A25, it is possible to detect the potential influence of vertical air motion on the raingage-microwave rainfall comparisons.

Jameson, Arthur R.↗
NASA NTRS2018

Time-Varying Manual Control Identification in a Stall Recovery Task Under Different Simulator Motion Conditions

This paper adds data to help the development of simulator motion cueing guidelines for stall recovery training by identifying time-varying manual control behavior in a stall recovery task under different simulator motion conditions. A study was conducted with seventeen general aviation pilots in the NASA Ames Vertical Motion Simulator. Pilots had to follow a flight director through four stages of a high-altitude stall task. A time-varying identification method was used to quantify how pilot manual control parameters change throughout different stages of the task in both roll and pitch. Four motion configurations were used: no motion, generic hexapod motion, enhanced hexapod motion and full motion. Pilot performance was highest for the enhanced hexapod and full motion configurations in both roll and pitch, and the lowest without motion. In the roll axis, the pilot position gain did not significantly change throughout the stall task, but was the lowest for the condition with no motion. The pilot roll velocity gain was significantly different between motion conditions, the largest difference being found close to the stall point. The enhanced hexapod motion condition had the highest pilot roll velocity gain. In the pitch axis, the pilot position gain was significantly different between time segments but not between motion conditions. The pilot pitch velocity gain was highest for the full motion condition and increased close to the stall point, but did not change significantly for the other motion conditions. Overall, pilot control behavior under enhanced hexapod motion was most similar to that under full aircraft motion. This indicates that motion cueing for stall recovery training on hexapod simulators might be improved by using the principles behind the enhanced hexapod motion configuration.

manual control↗
NASA NTRS1977

Effect of gyro verticality error on lateral autoland tracking performance for an inertially smoothed control law

The results of a simulation study performed to determine the effects of gyro verticality error on lateral autoland tracking and landing performance are presented. A first order vertical gyro error model was used to generate the measurement of the roll attitude feedback signal normally supplied by an inertial navigation system. The lateral autoland law used was an inertially smoothed control design. The effect of initial angular gyro tilt errors (2 deg, 3 deg, 4 deg, and 5 deg), introduced prior to localizer capture, were investigated by use of a small perturbation aircraft simulation. These errors represent the deviations which could occur in the conventional attitude sensor as a result of the maneuver-induced spin-axis misalinement and drift. Results showed that for a 1.05 deg per minute erection rate and a 5 deg initial tilt error, ON COURSE autoland control logic was not satisfied. Failure to attain the ON COURSE mode precluded high control loop gains and localizer beam path integration and resulted in unacceptable beam standoff at touchdown.

Thibodeaux, J. J.↗
NASA NTRS1993

Organization of cortical microtubules in graviresponding maize roots

Immunofluorescence labeling of cortical microtubules (MTs) was used to investigate the relationship between MT arrangement and changes in growth rate of the upper and lower sides of horizontally placed roots of maize (Zea mays L. cv. Merit). Cap cells and cells of the elongation zone of roots grown vertically in light or darkness showed MT arrangements that were transverse (perpendicular) to the growth direction. Microtubules of cells basal to the elongation zone typically showed oblique orientation. Two hours after horizontal reorientation, cap cells of gravicompetent, light-grown and curving roots contained MTs parallel to the gravity vector. The MT arrangement on the upper side of the elongation zone remained transverse but the MTs of the outer four to five layers of cortical cells along the lower side of the elongation zone showed reorientation parallel to the axis of the root. The MTs of the lower epidermis retained their transverse orientation. Dark-grown roots did not curve and did not show reorientation of MTs in cells of the root cap or elongation zone. The data indicate that MT depolymerization and reorientation is correlated with reduction in growth rate, and that MT reorientation is one of the steps of growth control of graviresponding roots.

NASA Discipline Plant Biology↗
NASA NTRS1994

Off-Axis Drag of Dendrite Fragments at Low Reynolds Number

The aim of the present investigation is to characterize the motion of dendrite fragments falling under the influence of gravity in a uniform liquid medium at low Reynolds number. In an earlier study, Zakhem, Weidman and de Groh (1992) reported on the settling speed of model equiaxed dendrite grains released along their axis of symmetry. In this follow-up study uniaxial model dendrite grains were released off-axis to observe and document their motion at different orientations. It was hypothesized that the dendrite models might rotate when released off-axis in which case an attempt would be made to document the ensuing unsteady motion. This latter event turned out to be in fact true: at the small but finite Reynolds numbers that existed, each uniaxial dendrite slowly rotated towards its equilibrium orientation while failing under the influence of gravity. In addition to completing the original goal, we have made use of a beads-on-a shell Stokes flow code to numerically determine the drag coefficient for capsules, i.e.. uniaxial dendrites without arms. The drag on horizontally and vertically falling capsules are reported and compared with measurements.

Weidman, P. D.↗
DOE OSTI2020

Analytical formula for pellet fuel source density in toroidal plasma configurations based on an areal deposition model

An analytical formula for the fuel source density η F (Ψ) over a magnetic flux surface Ψ following pellet injection is derived. During pellet motion the ablated and ionized fuel will be initially deposited nearby the pellet, prior to subsequent homogenization within the magnetic flux surfaces. Here in our research, it is assumed that the deposition area projected normal to the magnetic field is on the order of the cross-sectional area of the ionized ablation column whose axis is aligned with the magnetic field. Previous pellet deposition codes [1] employed a point source deposition approximation, which overpredicts the surface-averaged density, particularly when the obliquity between the pellet trajectory and the flux surface normal approaches 90 degrees. A key finding of this study is that as the obliquity approaches 90 degrees, grazing trajectory, the areal model predicts a well behaved η F and removes the unphysical divergence stemming from the point model. To illustrate the difference exhibited between areal and point models for near grazing trajectories, we considered vertical pellet injection into a CFETR-like tokamak with a negative triangularity plasma cross section using a pellet ablation/deposition module.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1988

In-flight simulation investigation of rotorcraft pitch-roll cross coupling

An in-flight simulation experiment investigating the handling qualities effects of the pitch-roll cross-coupling characteristic of single-main-rotor helicopters is described. The experiment was conducted using the NASA/Army CH-47B variable stability helicopter with an explicit-model-following control system. The research is an extension of an earlier ground-based investigation conducted on the NASA Ames Research Center's Vertical Motion Simulator. The model developed for the experiment is for an unaugmented helicopter with cross-coupling implemented using physical rotor parameters. The details of converting the model from the simulation to use in flight are described. A frequency-domain comparison of the model and actual aircraft responses showing the fidelity of the in-flight simulation is described. The evaluation task was representative of nap-of-the-Earth maneuvering flight. The results indicate that task demands are important in determining allowable levels of coupling. In addition, on-axis damping characteristics influence the frequency-dependent characteristics of coupling and affect the handling qualities. Pilot technique, in terms of learned control crossfeeds, can improve performance and lower workload for particular types of coupling. The results obtained in flight corroborated the simulation results.

Watson, Douglas C.↗
NASA NTRS1991

Adaptive control of Space Station during nominal operations with CMGs

An adaptive control approach is investigated for the Space Station. The main components of the adaptive controller are the parameter identification scheme, the control gain calculation, and the control law. The control law is the Space Station baseline control law. The control gain calculation is based on linear quadratic regulator theory with eigenvalue placement in a vertical strip. The parameter identification scheme is a real-time recursive extended Kalman filter which estimates the inertias and also provides an estimate of the unmodeled disturbances due to the aerodynamic torques and to the nonlinear effects. An analysis of the inertia estimation problem suggests that it is possible to compute accurate estimates of the Space Station inertias during nominal CMG (control moment gyro) operations. The closed-loop adaptive control law is shown to be capable of stabilizing the Space Station after large inertia changes. Results are presented for the pitch axis.

Bishop, R. H.↗
NASA NTRSDate not supplied

Mechanical Design of the Urban Air Mobility Side-by-Side Test Stand

The Urban Air Mobility Side-by-Side Test Stand (SBS) is a new capability for the National Aeronautics and Space Administration (NASA) to test the conceptual side-by-side rotorcraft configuration. This test stand enhances the experimental capabilities of the Revolutionary Vertical Lift Technology (RVLT) Project and is primarily designed to be tested in the U.S. Army’s 7-by 10-Foot Wind Tunnel at NASA Ames Research Center. One of the goals for the SBS is to identify the optimal degree of rotor overlap that will yield the best aerodynamic performance. The SBS has two counter-rotating, intermeshing rotors that can vary in lateral separation. The test stand can pitch nose up and nose down, with each rotor having the capability to be trimmed independently through cyclic and collective controls. Six-axis load cells and rotary torque sensors are placed underneath each rotor to measure the thrust, torque, and side force from each rotor system. This paper describes the mechanical design of the SBS and outlines the structural analyses conducted to ensure a safety factor of 4 for ultimate strength and 3 for yield strength during all experimental testing.

Mechanical Design↗
NASA NTRSDate not supplied

Space Needle Returns

STEP is imported into Engineering Sketch Pad. Some bodies where slightly scaled and translated in OpenCSM to create a manifold solid for the downstream meshing process. The braces at the base and columns around the core are omitted because their solids are malformed or created nonmanifold intersections. EGADS provides an initial tessellation of the surface. refine adapted the surface mesh to a curvature and feature size metric. TetGen initially filled the volume. The TetGen mesh is adapted to the Spalding Law of the Wall u+ with refine to provide the initial mesh for flow solution. Solution-based mesh adaptation is performed where FUN3D-FV computes the flow solution with the Reynolds-averaged Navier-Stokes equations coupled to the Spalart-Allmaras turbulence model. The freestream Mach number is 4 approaching 40° from the central axis of the Space Needle. The volume and surface mesh is adapted with refine to reduce estimated interpolation error in Mach number via the multiscale metric. The adapted mesh implicitly resolves the boundary layers, shocks, and expansions. The surface mesh is shown for the lee side with a slice through the volume on the left. Computational schlieren in the lower right shows density variations. A slice of the mesh is colored with Mach number in the upper right where mesh with freestream Mach number is not rendered. The volume mesh contains 64 million vertices. A NASA worm logo is sketched and extruded into a solid in OpenCSM. The worm is unioned to the Space Needle roof to produce the inset mesh image.

mesh↗
DOE OSTI2022

The Milky Way’s middle-aged inner ring

Aims. We investigate the metallicity, age, and orbital anatomy of the inner Milky Way, specifically focussing on the outer bar region. Methods. We integrated a sample of APOGEE DR16 inner Galaxy stars in a state of the art bar-bulge potential with a slow pattern speed and investigated the link between the resulting orbits and their [Fe/H] and ages. By superimposing the orbits, we built density, [Fe/H], and age maps of the inner Milky Way, which we divided further using the orbital parameters eccentricity, |Xmax|, and |Zmax|. Results. We find that at low heights from the Galactic plane, the Galactic bar gradually transitions into a radially thick, vertically thin, elongated inner ring with average solar [Fe/H]. This inner ring is mainly composed of stars with AstroNN ages between 4 and 9 Gyr with a peak in age between 6 and 8 Gyr, making the average age of the ring ~6 Gyr. The vertical thickness of the ring decreases markedly towards younger ages. We also find very large L4 Lagrange orbits that have average solar to super-solar metallicities and intermediate ages. Lastly, we confirm a clear X-shape in the [Fe/H] and density distributions at large Galactic heights. Conclusions. The orbital structure obtained for the APOGEE stars reveals that the Milky Way hosts an inner ring-like structure between the planar bar and corotation. This structure is on average metal rich, intermediately aged, and enhances the horizontal metallicity gradient along the bar’s major axis.

79 ASTRONOMY AND ASTROPHYSICS↗
NASA NTRS2000

TAILSIM Users Guide

The TAILSIM program uses a 4th order Runge-Kutta method to integrate the standard aircraft equations-of-motion (EOM). The EOM determine three translational and three rotational accelerations about the aircraft's body axis reference system. The forces and moments that drive the EOM are determined from aerodynamic coefficients, dynamic derivatives, and control inputs. Values for these terms are determined from linear interpolation of tables that are a function of parameters such as angle-of-attack and surface deflections. Buildup equations combine these terms and dimensionalize them to generate the driving total forces and moments. Features that make TAILSIM applicable to studies of tailplane stall include modeling of the reversible control System, modeling of the pilot performing a load factor and/or airspeed command task, and modeling of vertical gusts. The reversible control system dynamics can be described as two hinged masses connected by a spring. resulting in a fifth order system. The pilot model is a standard form of lead-lag with a time delay applied to an integrated pitch rate and/or airspeed error feedback. The time delay is implemented by a Pade approximation, while the commanded pitch rate is determined by a commanded load factor. Vertical gust inputs include a single 1-cosine gust and a continuous NASA Dryden gust model. These dynamic models. coupled with the use of a nonlinear database, allow the tailplane stall characteristics, elevator response, and resulting aircraft response, to be modeled. A useful output capability of the TAILSIM program is the ability to display multiple post-run plot pages to allow a quick assessment of the time history response. There are 16 plot pages currently available to the user. Each plot page displays 9 parameters. Each parameter can also be displayed individually. on a one plot-per-page format. For a more refined display of the results the program can also create files of tabulated data. which can then be used by other plotting programs. The TAILSIM program was written straightforwardly assuming the user would want to change the database tables, the buildup equations, the output parameters. and the pilot model parameters. A separate database file and input file are automatically read in by the program. The use of an include file to set up all common blocks facilitates easy changing of parameter names and array sizes.

Hiltner, Dale W.↗
NASA NTRS2000

An all-silicon single-wafer micro-g accelerometer with a combined surface and bulk micromachining process

This paper reports an all-silicon fully symmetrical z-axis micro-g accelerometer that is fabricated on a single-silicon wafer using a combined surface and bulk fabrication process. The microaccelerometer has high device sensitivity, low noise, and low/controllable damping that are the key factors for attaining micro g and sub-micro g resolution in capacitive accelerometers. The microfabrication process produces a large proof mass by using the whole wafer thickness and a large sense capacitance by utilizing a thin sacrificial layer. The sense/feedback electrodes are formed by a deposited 2-3 microns polysilicon film with embedded 25-35 microns-thick vertical stiffeners. These electrodes, while thin, are made very stiff by the thick embedded stiffeners so that force rebalancing of the proof mass becomes possible. The polysilicon electrodes are patterned to create damping holes. The microaccelerometers are batch-fabricated, packaged, and tested successfully. A device with a 2-mm x 1-mm proof mass and a full bridge support has a measured sensitivity of 2 pF/g. The measured sensitivity of a 4-mm x 1-mm accelerometer with a cantilever support is 19.4 pF/g. The calculated noise floor of these devices at atmosphere are 0.23 micro g/sqrt(Hz) and 0.16 micro g/sqrt(Hz), respectively.

Non-NASA Center↗
NASA NTRS1992

Spatial orientation of the vestibular system

1. A simplified three-dimensional state space model of visual vestibular interaction was formulated. Matrix and dynamical system operators representing coupling from the semicircular canals and the visual system to the velocity storage integrator were incorporated into the model. 2. It was postulated that the system matrix for a tilted position was a composition of two linear transformations of the system matrix for the upright position. One transformation modifies the eigenvalues of the system matrix while another rotates the pitch and roll eigenvectors with the head, while maintaining the yaw axis eigenvector approximately spatially invariant. Using this representation, the response characteristics of the pitch, roll, and yaw eye velocity were obtained in terms of the eigenvalues and associated eigenvectors. 3. Using OKAN data obtained from monkeys and comparing to the model predictions, the eigenvalues and eigenvectors of the system matrix were identified as a function of tilt to the side or of tilt to the prone positions, using a modification of the Marquardt algorithm. The yaw eigenvector for right-side-down tilt and for downward pitch cross-coupling was approximately 30 degrees from the spatial vertical. For the prone position, the eigenvector was computed to be approximately 20 degrees relative to the spatial vertical. For both side-down and prone positions, oblique OKN induced along eigenvector directions generated OKAN which decayed to zero along a straight line with approximately a single time constant. This was verified by a spectral analysis of the residual sequence about the straight line fit to the decaying data. The residual sequence was associated with a narrow autocorrelation function and a wide power spectrum. 4. Parameters found using the Marquardt algorithm were incorporated into the model. Diagonal matrices in a head coordinate frame were introduced to represent the direct pathway and the coupling of the visual system to the integrator. Model simulations predicted the behavior of yaw and pitch OKN and OKAN when the animal was upright, as well as the cross-coupling in the tilted position. The trajectories in velocity space were also accurately simulated. 5. There were similarities between the monkey eigenvectors and human perception of the spatial vertical. For side-down tilts and downward eye velocity cross-coupling, there was only an Aubert (A) effect. For upward eye velocity cross-coupling there were both Muller (E) and Aubert (A) effects. The mean of the eigenvectors for upward and downward eye velocities overlay human 1 x g perceptual data.(ABSTRACT TRUNCATED AT 400 WORDS).

NASA Discipline Neuroscience↗
DOE OSTI2023

Advances in 3D Geologic Modeling of Alluvial Basins with a Focus on Facies and Property Modeling

The unsaturated zone alluvium reference case is one of several geologic systems under consideration by the U.S. Department of Energy Office of Nuclear Energy for hosting repositories for spent nuclear fuel and associated waste (Sevougian et al., 2019). As noted by Mariner et al. (2018), the generic alluvial basin offers positive attributes that merit its consideration as a reference case by the Spent Fuel and Waste Science and Technology (SFWST) campaign. There are hundreds of alluvial basins and sub-basins scattered across the arid western United States (Figure 1-1). Precipitation and infiltration rates are relatively low with high evapotranspiration, resulting in vertical separation between repository and water table and thus longer transport paths to an aquifer. Accumulations of alluvial sediments within these basins are typically on the order of hundreds of meters, and locally may exceed 1,000 m in thickness, as is the case for the Deming sub-basin in southern New Mexico. A thick geologic host medium, which serves as the natural barrier system (NBS) in the conceptual model framework of a geologic disposal system, isolates the waste packages from receptors in the biosphere. Further, alluvial basin fill is typically comprised of stacked playa and lacustrine deposits along the basin axis (Perry et al., 2018). Characterized by low permeability, these layers protect the biosphere above the repository and the groundwater resources below the repository.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Dimensional stability of low-cost thermoplastic composite molds

This report addresses a key question for using additively manufactured tooling from carbon fiber reinforced thermoplastic composites. How does the distortion of the molded part change with the print orientation used in the manufacture of tooling? The objective of this research was to discuss the distortion of parts molded with such tooling, in relation to the deflections in the tooling during the compression molding process. This was achieved through both model simulations and experimental molding runs. A vertical orientation was used in printing the mold with a distinctly non-planar surface: this orientation allowed for higher performance along the press closing direction -- higher thermal conductivity, higher stiffness, and lower coefficient of thermal expansion. Epoxy-carbon fiber twill weave fabric prepreg was then compression molded in this mold. The thermomechanical properties of the tooling material and the molded part were measured and used in simulation of mold deformation as well as part distortion. The thermomechanical anisotropy of the mold is quite different from that of the molded part because in the mold, the stiffest direction is the z-axis, while in the molded thermoset part, the z-axis is the weakest direction. The connection between mold deformation during the compression molding process and the final part distortion can be seen from the simulation results. The simulation results for the case where the mold was four times as stiff as the part along the press closing direction compared well with experiment. When the mold stiffness was lowered in relation to the part stiffness, the mold deformation during the compression molding increased; but this led to a smaller extent of part distortion.

36 MATERIALS SCIENCE↗