Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “vacuum processes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39

Low Power, Wide Dynamic Range Carbon Nanotube Vacuum Gauges

This slide presentation presents carbon nanotube vacuum pressure sensor gauges that operate at low power and exhibit a wide-dynamic range based on microelectromechanical systems (MEMS) technology. The fabrication facility, and the formation process are shown. Pressure sensitivity was found to increase rapidly as the bias power was increased. In addition, by etching part of the thermal SiO2 beneath the tubes and minimizing heat conduction through the substrate, pressure sensitivity was extended toward lower pressures. Results are compared to a conventional thin film meander resistor, which was fabricated and whose pressure response was also measured for comparative purposes.

JEOL E-beam aligner↗

Progress in Fabrication of Rocket Combustion Chambers by VPS

Several documents in a collection describe aspects of the development of advanced materials and fabrication processes intended to enable the manufacture of advanced rocket combustion chambers and nozzles at relatively low cost. One concept discussed in most of the documents is the fabrication of combustion-chamber liners by vacuum plasma spraying (VPS) of an alloy of 88Cu/8Cr/4Nb (numbers indicate atomic percentages) -- a concept that was reported in "Improved Alloy for Fabrication of Combustion Chambers by VPS" (MFS-26546). Another concept is the deposition of graded-composition wall and liner structures by VPS in order to make liners integral parts of wall structures and to make oxidation- and thermal-protection layers integral parts of liners: The VPS process is started at 100 percent of a first alloy, then the proportion of a second alloy is increased gradually from zero as deposition continues, ending at 100 percent of the second alloy. Yet another concept discussed in one of the documents is the VPS of oxidation-protection coats in the forms of nickel-and-chromium-containing refractory alloys on VPS-deposited 88Cu/8Cr/4Nb liners.

Holmes, Richard R.↗

Large Eddy Simulation (LES) of Particle-Laden Temporal Mixing Layers

High-fidelity models of plume-regolith interaction are difficult to develop because of the widely disparate flow conditions that exist in this process. The gas in the core of a rocket plume can often be modeled as a time-dependent, high-temperature, turbulent, reacting continuum flow. However, due to the vacuum conditions on the lunar surface, the mean molecular path in the outer parts of the plume is too long for the continuum assumption to remain valid. Molecular methods are better suited to model this region of the flow. Finally, granular and multiphase flow models must be employed to describe the dust and debris that are displaced from the surface, as well as how a crater is formed in the regolith. At present, standard commercial CFD (computational fluid dynamics) software is not capable of coupling each of these flow regimes to provide an accurate representation of this flow process, necessitating the development of custom software. This software solves the fluid-flow-governing equations in an Eulerian framework, coupled with the particle transport equations that are solved in a Lagrangian framework. It uses a fourth-order explicit Runge-Kutta scheme for temporal integration, an eighth-order central finite differencing scheme for spatial discretization. The non-linear terms in the governing equations are recast in cubic skew symmetric form to reduce aliasing error. The second derivative viscous terms are computed using eighth-order narrow stencils that provide better diffusion for the highest resolved wave numbers. A fourth-order Lagrange interpolation procedure is used to obtain gas-phase variable values at the particle locations.

Bellan, Josette↗

Better Thermal Insulation in Solar-Array Laminators

Glass marbles improve temperature control. Modified vacuum laminator for photovoltaic solar arrays includes thermal insulation made of conventional glass marbles. Marbles serve as insulation for temperature control of lamination process at cure temperatures as high as 350 degrees F. Used to replace original insulation made of asbestos cement.

Burger, D. R.↗

Processing, physical metallurgy and creep of NiAl + Ta and NiAl + Nb alloys

Powder processed NiAl + Ta alloys containing 1, 2, and 4.5 at percent tantalum and NiAl + Nb alloys containing 1 and 2 at percent niobium were developed for improved creep properties. In addition, a cast alloy with 5 at percent tantalum was also studied. Hot extrusion parameters for processing alloys with 1 and 2 at percent of tantalum or niobium were designed. The NiAl + 4.5 at percent Ta alloy could be vacuum hot pressed successfully, even though it could not be extruded. All the phases in the multiphase alloys were identified and the phase transformations studied. The Ni2AlTa in NiAl + 4.5 at percent Ta alloy transforms into a liquid phase above 1700 K. Solutionizing and annealing below this temperature gives rise to a uniform distribution of fine second phase precipitates. Compressive creep properties were evaluated at 1300 K using constant load and constant velocity tests. In the higher strain rate region single phase NiAl + 1 at percent Ta and NiAl + 1 at percent Nb alloys exhibit a stress exponent of 5 characteristic of climb controlled dislocation creep. In slower strain rate regime diffusional creep becomes important. The two phase alloys containing 2 to 5 at percent Ta and 2 at percent Nb show considerable improvement over binary NiAl and single phase alloys. Loose dislocation networks and tangles stabilized by the precipitates were found in the as crept microstructure. The cast alloy which has larger grains and a distribution of fine precipitates shows the maximum improvement over binary NiAl.

Pathare, Viren M.↗

Space resources. Overview

Space resources must be used to support life on the Moon and in the exploration of Mars. Just as the pioneers applied the tools they brought with them to resources they found along the way rather than trying to haul all their needs over a long supply line, so too must space travelers apply their high technology tools to local resources. This overview describes the findings of a study on the use of space resources in the development of future space activities and defines the necessary research and development that must precede the practical utilization of these resources. Space resources considered included lunar soil, oxygen derived from lunar soil, material retrieved from near-Earth asteroids, abundant sunlight, low gravity, and high vacuum. The study participants analyzed the direct use of these resources, the potential demand for products from them, the techniques for retrieving and processing space resources, the necessary infrastructure, and the economic tradeoffs.

Mckay, Mary Fae↗

Space Resources

Space resources must be used to support life on the Moon and exploration of Mars. Just as the pioneers applied the tools they brought with them to resources they found along the way rather than trying to haul all their needs over a long supply line, so too must space travelers apply their high technology tools to local resources. The pioneers refilled their water barrels at each river they forded; moonbase inhabitants may use chemical reactors to combine hydrogen brought from Earth with oxygen found in lunar soil to make their water. The pioneers sought temporary shelter under trees or in the lee of a cliff and built sod houses as their first homes on the new land; settlers of the Moon may seek out lava tubes for their shelter or cover space station modules with lunar regolith for radiation protection. The pioneers moved further west from their first settlements, using wagons they had built from local wood and pack animals they had raised; space explorers may use propellant made at a lunar base to take them on to Mars. The concept for this report was developed at a NASA-sponsored summer study in 1984. The program was held on the Scripps campus of the University of California at San Diego (UCSD), under the auspices of the American Society for Engineering Education (ASEE). It was jointly managed under the California Space Inst. and the NASA Johnson Space Center, under the direction of the Office of Aeronautics and Space Technology (OAST) at NASA Headquarters. The study participants (listed in the addendum) included a group of 18 university teachers and researchers (faculty fellows) who were present for the entire 10-week period and a larger group of attendees from universities, Government, and industry who came for a series of four 1-week workshops. The organization of this report follows that of the summer study. Space Resources consists of a brief overview and four detailed technical volumes: (1) Scenarios; (2) Energy, Power, and Transport; (3) Materials; (4) Social Concerns. Although many of the included papers got their impetus from workshop discussions, most have been written since then, thus allowing the authors to base new applications on established information and tested technology. All these papers have been updated to include the authors' current work. This overview, drafted by faculty fellow Jim Burke, describes the findings of the summer study, as participants explored the use of space resources in the development of future space activities and defined the necessary research and development that must precede the practical utilization of these resources. Space resources considered included lunar soil, oxygen derived from lunar soil, material retrieved from near-Earth asteroids, abundant sunlight, low gravity, and high vacuum. The study participants analyzed the direct use of these resources, the potential demand for products from them, the techniques for retrieving and processing space resources, the necessary infrastructure, and the economic tradeoffs. This is certainly not the first report to urge the utilization of space resources in the development of space activities. In fact, Space Resources may be seen as the third of a trilogy of NASA Special Publications reporting such ideas arising from similar studies. It has been preceded by Space Settlements: A Design Study (NASA SP-413) and Space Resources and Space Settlements (NASA SP-428). And other, contemporaneous reports have responded to the same themes. The National Commission on Space, led by Thomas Paine, in Pioneering the Space Frontier, and the NASA task force led by astronaut Sally Ride, in Leadership and America's Future in Space, also emphasize expansion of the space Infrastructure; more detailed exploration of the Moon, Mars, and asteroids; an early start on the development of the technology necessary for using space resources; and systematic development of the skills necessary for long-term human presence in space. Our report does not represent any Government-authorized view or official NASA policy. NASA's official response to these challenging opportunities must be found in the reports of its Office of Exploration, which was established in 1987. That office's report, released in November 1989, of a 90-day study of possible plans for human exploration of the Moon and Mars is NASA's response to the new initiative proposed by President Bush on July 20, 1989, the 20th anniversary of the Apollo 11 landing on the Moon: "First, for the coming decade, for the 1990s, Space Station Freedom, our critical next step in all our space endeavors. And next, for the new century, back to the Moon, back to the future, and this time, back to stay. And then a journey into tomorrow, a journey to another planet, a manned mission to Mars." This report, Space Resources, offers substantiation for NASA's bid to carry out that new initiative.

McKay, Mary Fae↗

An Experimental Study on Low Pressure Frost Formation for Lunar Polar Water Capture

In-situ resource utilization (ISRU) is a vital component of NASA’s mission to the Moon and beyond, as the extraction of resources from the environment can reduce payload weight and the frequency of resupply missions. Since the discovery of water in the regolith of the permanently shadowed regions (PSR) of the Moon, its extraction and transport has become an area of increasing interest for NASA. One proposed method is heating icy regolith to free the water before desublimating and transporting it as ice in a tanker. However, little is known regarding the dynamics of frost growth at low pressures, and an understanding of the heat transfer process is required to properly size the heat exchanger for the tanker. To investigate this phenomenon, a cold plate was placed in a vacuum chamber with water vapor directed at its surface. The chamber pressure (300 and 500 Pa) and cold plate temperature (–18 to –5 °C) were kept below the triple point and varied throughout the experiment to examine their impact on frost layer heat transfer. As water flowed into the chamber and deposited on the cold plate surface, the heat flux and temperature were measured along with the frost layer thickness and/or mass. Density calculated at the conclusion of each test suggests the frost layer is denser than that of frost grown at atmospheric pressure. The results demonstrate unexpected density and heat transfer characteristics and require development of a new model of frost growth for lunar conditions.

In situ Resource Utiliztion↗

An Experimental Study on Low Pressure Frost Formation for Lunar Polar Water Capture

In-situ resource utilization (ISRU) is a vital component of NASA’s mission to the Moon and beyond, as the extraction of resources from the environment can reduce payload weight and the frequency of resupply missions. Since the discovery of water in the regolith of the permanently shadowed regions (PSR) of the Moon, its extraction and transport has become an area of increasing interest for NASA. One proposed method is heating icy regolith to free the water before de-sublimating and transporting it as ice in a tanker. However, little is known regarding the dynamics of frost growth at low pressures, and an understanding of the heat transfer process is required to properly size the heat exchanger for the tanker. To investigate this phenomenon, a cold plate was placed in a vacuum chamber with water vapor directed at its surface. The chamber pressure (300 and 500 Pa) and cold plate temperature (–18 to –5 °C) were kept below the triple point and varied throughout the experiment to examine their impact on frost layer heat transfer. As water flowed into the chamber and deposited on the cold plate surface, the heat flux and temperature were measured along with the frost layer thickness and/or mass. Density calculated at the conclusion of each test suggests the frost layer is denser than that of frost grown at atmospheric pressure. The results demonstrate unexpected density and heat transfer characteristics and require development of a new model of frost growth for lunar conditions

Lunar polar↗

Process for the preparation of calcium superoxide

Calcium superoxide is prepared in high yields by spreading a quantity of calcium peroxide diperoxyhydrate on the surface of a container, positioning said container in a vacuum chamber on a support structure through which a coolant fluid can be circulated, partially evacuating said vacuum chamber, allowing the temperature of the diperoxyhydrate to reach the range of about 0 to about 40 C; maintaining the temperature selected for a period of time sufficient to complete the disproproriation of the diperoxyhydrate to calcium superoxide, calcium hydroxide, oxygen, and water; constantly and systematically removing the water as it is formed by sweeping the reacting material with a current of dry inert gas and/or by condensation of said water on a cold surface; backfilling the chamber with a dry inert gas; and finally, recovering the calcium superoxide produced.

Ballou, E. V.↗

Spaceflight Autonomous Multigenerational Microbial Sequencer (SAMMS) in Support of Plant-Growth Systems

As the National Aeronautics and Space Association (NASA) begins to pursue long-duration space flights, they will need to be able to provide astronauts with a nutritious and reliable food source. To meet the administration’s goal of traveling to the Moon and Mars, astronauts will need to begin to grow their own food in space. To protect their food source, extensive monitoring will occur to test for the effects of a space flight environment (e.g., radiation) as well as for early pathogen and disease detection. Genomic sequencing allows for both concerns to be tested on a regular basis. However, NASA’s current sequencer is unable to process plant tissues. Therefore, a novel method for plant DNA extraction using microneedle (MN) patches that will be able to feed into NASA’s existing system, but also require minimal human input is proposed. To support this, the design was broken down into four components (1) MN patch fabrication (2) MN patch extraction, (3) automated sampling motion control, and (4) a processing module. The MN patch is fabricated using a custom mold with conically shaped needles. The mold is filled with Polyvinyl alcohol (PVA) solution and placed in a vacuum desiccator. The mold is left in the vacuum overnight until the patch is dry and ready for use. The protocol was tested with varying pressures, drying times, volume amounts, and preparation methods to determine if highquality needles can be produced. A MN is a method of DNA extraction where the patch is applied to a leaf, the needles penetrate the leaf, breaking the rigid plant cell wall to isolate the DNA. A protocol for this method of extraction was tested to ensure the patch could produce the needed yield and purity. The tests varied by the number of patches, number of applications, and plant type. To automate the MN extraction method, motion control will utilize two separate axis tables which move in the x and y directions. The y-axis table will have an end effector that fits a MN patch and will have the ability to apply the patch to the leaf sample. This end effector will also act as a lid for a downstream processing module. The other axis will position the leaf sample and processing container so that the patch can be applied accurately. The Joint Comprehensive Sequencing System (JCSS) module integrates all the components together. The output of this module feeds into the NASA Charged Information-Storage Polymer Preparation System (CHIPPS) for genomic sequencing. The extraction module operates using a series of syringes and tubing to pump the varying reagents needed for the extraction protocol. The results of the study proved that MN patches are a viable method of DNA extraction. While fabrication of high-quality needles was unsuccessful, the protocol was able to be further developed using centrifugation. The integrated design between the motion control and the JCSS enabled the potential for automation with a complete conceptual design and prototype. Future research and development for this study would include (1) further testing for fabrication (2) expanding the range of plant species compatible with the MN patch, and (3) building a working prototype for the integrated system.

Peter Ling↗

Influence of evaporation rate and chamber pressure on the FUV reflectance and physical characteristics of aluminum films

Space telescopes for studying astrophysical phenomena from the far ultraviolet (FUV) to the near infrared (NIR) require durable mirror coatings with high and uniform reflectance over a very broad spectral region. While coatings for the optical and NIR region are well developed with proven performance, the FUV band presents significant challenges, particularly below 115 nm. Recent developments in physical vapor deposition (PVD) coating processes of aluminum mirrors that are protected with a metal-fluoride overcoat to prevent oxidation (such as LiF, MgF2, or AlF3) have improved reflectance in the FUV. While the emphasis in these studies has been placed on improving the deposition conditions of the metal-fluoride overcoats, less attention has been devoted to how deposition parameters (such as vacuum conditions or deposition rates) may affect the quality of the aluminum mirrors. This paper presents characterization of Al+MgF2 coupons made by flash evaporation of aluminum followed by resistive evaporation of MgF2. Samples were manufactured under a variety of processing conditions and the relationship between processing variables and mirror FUV reflectivity is analyzed. Performance characterization was based on the measured near-normal reflectance in the FUV (90-180 nm), and normal-incidence transmittance in the visible was done to analyze the possible presence of pinholes in the mirror. We demonstrated pinhole-free Al/MgF2 mirrors deposited at room temperature with a reflectivity of 0.91 at 122 nm wavelength. This reflectivity enhancement was achieved solely through parameter optimization.

Manuel A. Quijada↗

Influence of Evaporation Rate and Chamber Pressure on the FUV Reflectance and Physical Characteristics of Aluminum Films

Space telescopes for studying astrophysical phenomena from the far ultraviolet (FUV) to the near infrared (NIR) require durable mirror coatings with high and uniform reflectance over a very broad spectral region. While coatings for the optical and NIR region are well developed with proven performance, the FUV band presents significant challenges, particularly below 115 nm. Recent developments in physical vapor deposition (PVD) coating processes of aluminum mirrors that are protected with a metal-fluoride overcoat to prevent oxidation (such as LiF, MgF2, or AlF3) have improved reflectance in the FUV. While the emphasis in these studies has been placed on improving the deposition conditions of the metal-fluoride overcoats, less attention has been devoted to how deposition parameters (such as vacuum conditions or deposition rates) may affect the quality of the aluminum mirrors. This paper presents characterization of Al+MgF2 coupons made by flash evaporation of aluminum followed by resistive evaporation of MgF2. Samples were manufactured under a variety of processing conditions and the relationship between processing variables and mirror FUV reflectivity is analyzed. Performance characterization was based on the measured near-normal reflectance in the FUV (90-180 nm), and normal-incidence transmittance in the visible was done to analyze the possible presence of pinholes in the mirror. We demonstrated pinhole-free Al/MgF2 mirrors deposited at room temperature with a reflectivity of 0.91 at 122 nm wavelength. This reflectivity enhancement was achieved solely through parameter optimization.

FUV reflectance, aluminum, PVD, deposition rate, A↗

Microstructures and properties of rapidly solidified alloys

The microstructure and properties of rapidly solidified aluminum alloys were researched. The effects of powder and flake chemistry and morphology and alternative consolidation processing parameters are being conducted. Samples of the powders being utilized were obtained for comprehensive metallurgical characterization. Seven aluminum alloys in the form of thin foils were studied by a variety of techniques including optical metallography, scanning electron microscope, and transmission electron microscope. Details of the microstructural characteristics are presented along with a discussion of the solidification process. A better understanding of the microstructure of the rapidly solidified aluminum alloys prepared by a variety of techniques such as roller quenching, the vacuum atomized procedure, ultrasonically atomized in inert atmospheres, and atomized in flue gas was provided.

Shechtman, D.↗

Ge/Si Integrated Circuit For Infrared Imaging

Proposed integrated circuit consists of focal-plane array of metal/germanium Schottky-barrier photodetectors on same chip with silicon-based circuits that processes signals from photodetectors. Made compatible with underlying silicon-based circuitry by growing germanium epitaxially on silicon circuit wafers. Metal deposited in ultrahigh vacuum immediately after growth of germanium. Combination of described techniques results in high-resolution infrared-imaging circuits of superior performance.

Fathauer, Robert W.↗

The effect of simulated low earth orbit radiation on polyimides (UV degradation study)

UV degradation of polyimide films in air and vacuum were studied using UV-visible, ESR, FTIR, and XPS spectroscopies. The UV-visible spectra of polyimide films showed a blue shift in the absorption compared to Kapton. This behavior was attributed to the presence of bulky groups and kinks along the polymer chains which disrupt the formation of a charge transfer complex. The UV-visible spectra showed also that UV irradiation of polyimides result extensively in surface degradation, leaving the bulk of the polymer intact. ESR spectra of polyimides irradiated in vacuum revealed the formation of stable carbon-centered radicals which give a singlet ESR spectrum, while polyimides irradiated in air produced an asymmetric signal shifted to a lower magnetic field, with a higher g value and line width. This signal was attributed to oxygen-cenetered radicals of peroxy and/or alkoxy type. The rate of radical formation in air was two fold higher than for vacuum irradiation, and reached a plateau after a short time. This suggests a continuous depletion of radicals on the surface via an ablative degradation process. FTIR, XPS, and weight loss studies supported this postulate. An XPS study of the surface indicated a substantial increase in the surface oxidation after irradiation in air. The sharp increase in the C-O binding energy peak relative to the C-C peak was believed to be associated with an aromatic ring opening reaction.

Forsythe, John S.↗

Understanding the Chemistry of PAHs in H2O Ice

Polycyclic aromatic hydrocarbons (PAHs) can be incorporated into H O ice grains and mantles found in dense molecular clouds, comets, interplanetary dust particles (IDPs), and many Solar System objects. However, laboratory infrared (IR) spectroscopic studies of PAHs in ices is still a relatively young field. Early research efforts have shown the rich chemistry of PAHs in H O to be dependent on PAH concentration, with the concentration impacting everything from IR band shifts to the photoproducts produced [1-6]. Similarly, research suggests that a potential top-down synthesis route for complex organic molecules or COMs found within solar systems is possible from PAHs in water ice [7]. In order to fully exploit the observations from the James Webb Space Telescope (JWST) more IR studies of PAHs in H O ice under relevant astrophysical conditions and planetary systems are needed. The NASA ICEE (Institute for Carbon Evolution Experiments), formerly the NASA Ames PAH IR Laboratory, has been at the forefront of this field. Starting in 2019, just before the COVID-19 shutdown, the ICEE laboratory underwent a major renovation, gearing it towards in-depth PAHs in H O ice research under relevant solar systems and interstellar conditions. The ICEE facility enables us to study the processing of PAHs in H O ice using UV photons and charged particle (electron) irradiation either singly or in combination under ultra-high vacuum and low temperature (15K). We use in-situ measurements with IR, Raman, and mass spectra by which we monitor the chemistry of PAHs in H O ice before, during and after the irradiation. This presentation will summarize the past work regarding PAHs in ices and provide an update on the latest ICEE research results in this area, outlining a roadmap for future research efforts.

Andrew Mattioda↗