Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “surface roughness”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39

Roughening Surfaces Of Solar Cells

Proposed treatment involving bombardment by ions gives silicon solar cells rough surfaces and increases amount of light absorbed by cells. First step of treatment, wafer of single-crystal silicon held at temperature of 70 degree C or higher while bombarded with argon or hydrogen ions at kinetic energies between 100 and 2,000 eV. This high dose produces damaged layer on surface, consisting of outer polycrystalline sublayer and underlying sublayer containing extended defects. Bombarded wafer then etched chemically. Photovoltaic conversion efficiency increases with number of reflections at surface of silicon cell because large part of light absorbed at each reflection. Deeply textured surface provides opportunities for multiple reflections.

Singh, Ranbir↗

Hexcomb Pattern Roughness Effects on Blunt Body Transition and Heating

An experimental investigation of hexcomb pattern surface roughness effects on boundary-layer transition and convective heating has been performed. Two representative entry vehicle geometries, a spherical-cap aeroshell and a sphere-cone aeroshell, were considered. Multiple cast ceramic models of each geometry were fabricated with various roughness pattern densities and depths that simulated an ablated hexcomb-structure thermal protection system. Wind tunnel testing was performed at Mach 6 over a range of Reynolds numbers sufficient to produce laminar, transitional, and turbulent flow. Aeroheating and boundary-layer transition onset data were obtained using global phosphor thermography. The experimental heating data are presented herein, as are comparisons to laminar and turbulent smooth-wall heat transfer distributions from computational flow field simulations. The experimental data were used to develop a unified boundary-layer transition correlation for both sandgrain distributed roughness and hexcomb pattern roughness.

Brian R Hollis↗

Remote measurement of salinity in an estuarine environment.

The microwave emission of sea water is dependent upon salinity in the low microwave spectrum, and it appears possible to measure remotely surface salinity at 21-cm wavelength with an accuracy up to one part salt per thousand parts water (.1%) for a .5 to 3.5% salinity range. The dielectric constant of sea water can be represented by that of NaCl, except that the sea water conductivity is retained. The effects of the atmosphere, cosmic noise, sea surface roughness, and constant radiometer errors can be corrected by using surface calibration measurements. In experiments performed in Mississippi and Louisiana coastal waters salinity accuracies of .3 to .5 were obtained. It is believed that the accuracy was limited by the radiometer used.

Thomann, G. C.↗

Thermal optical surface properties and high-temperature solar energy conversion

The effects of thermal surface properties on the performance of representative point focusing solar power plants are assessed in this paper. The tradeoff relationships are presented in terms of normalized system performance as a function of thermal optical design parameters. Crucial surface properties include solar reflectance, specular spreading due to microscopic roughness, surface error due to manufacturing slope tolerance or waviness and concentrator pointing accuracy. Two representative power conversion systems, a Rankine steam cycle and an open air Brayton cycle, are considered.

Wen, L.↗

A fundamental study of the sticking of insect residues to aircraft wings

The aircraft industry has long been concerned with the increase of drag on airplanes due to fouling of the wings by insects. The present research studied the effects of surface energy and surface roughness on the phenomenon of insect sticking. Aluminum plates of different roughnesses were coated with thin films of polymers with varying surface energies. The coated plates were attached to a custom jig and mounted on top of an automobile for insect collection. Contact angle measurements, X-ray photoelectron spectroscopy and specular reflectance infrared spectroscopy were used to characterize the surface before and after the insect impact experiments. Scanning electron microscopy showed the topography of insect residues on the exposed plates. Moments were calculated in order to find a correlation between the parameters studied and the amount of bugs collected on the plates. An effect of surface energy on the sticking of insect residues was demonstrated.

Eiss, N. S., Jr.↗

Acid dew and the role of chemistry in the dry deposition of reactive gases to wetted surfaces

A formalism is developed to describe the dry deposition of soluble reactive gases to wetted surfaces in terms of the relevant meteorological conditions, the surface roughness, the total amount of liquid water present on the surface, the rate of accumulation of this water, and the species' solubility and reactivity in the surface water. This formulation is then incorporated into a model designed to simulate the generation of acidic dew from the deposition of HNO3, SO2, S(IV) oxidants, H2O2, and O3. Similar to the observations of dew in the continental U.S., the model generates a dewdrop pH of about 4 by the end of the night; the pH can rapidly fall to toxic levels due to rapid evaporation after sunrise. Relatively low deposition velocities are predicted for the SO2 and O3 because of their lower solubilities and hence larger surface resistances than those of the other oxidants. Because the chemical lifetime of the SO2 in the dew is influenced by the atmospheric levels of H2O2, O3, and SO2, the SO2 deposition velocity is a strong function of these species' atmospheric abundances.

Chameides, William L.↗

Integrating Radar, Multispectral, and Landing Site Data for Analysis of the Lunar Surface

Radar maps of the Moon have been produced since the late 1960s, and have been used by a number of authors to study the surface roughness, subsurface rock abundance, and dielectric properties of the lunar surface. These studies focused on a range of topics, including the depth and rock population of the regolith, crater ejecta blankets, pyroclastic mantling layers, and cryptomare deposits. Limited radar sounding data from the Apollo missions identified layering in some regions of the maria. As radar datasets have improved in resolution and calibration, it has become more possible to make quantitative comparisons between the backscatter properties of the Moon, other remote-sensing observations, and the ground truth provided by Surveyor photos and Apollo traverses. This presentation will focus on the results of recent studies of the lunar regolith that make use of these diverse sources of information, and discuss research directions that will be possible with radar data to be collected in the near future.

Campbell, B. A.↗

Space Weathering in the Fine Size Fractions of Lunar Soils: Soil Maturity Effects

The effects of space weathering on the optical properties of lunar materials have been well documented. These effects include a reddened continuum slope, lowered albedo, and attenuated absorption features in reflectance spectra of lunar soils as compared to finely comminuted rocks from the same Apollo sites. However, the regolith processes that cause these effects are not well known, nor is the petrographic setting of the products of these processes fully understood. A Lunar Soil Characterization Consortium has been formed with the purpose of systematically integrating chemical and mineralogical data with the optical properties of lunar soils. Understanding space-weathering effects is critical in order to fully integrate the lunar sample collection with remotely-sensed data from recent robotic missions (e.g., Lunar Prospector, Clementine, and Galileo) We have shown that depositional processes (condensation of impact-derived vapors, sputter deposits, accreted impact material, e.g., splash glass, spherules, etc.) are a major factor in the modification of the optical surfaces of lunar regolith materials. In mature soils, it is the size and distribution of the nanophase metal in the soil grains that has the major effect on optical properties. In this report, we compare and contrast the space-weathering effects in an immature and a mature soil with similar elemental compositions. For this study, we analyzed <10 micron sieve fractions of two Apollo 17 soils, 79221 (mature, Is/FeO = 81) and 71061 (immature, Is/FeO = 14). Details of the sieving procedures and allocation scheme are given else where. The results of other detailed chemical, mineralogical, and spectroscopic analyses of these soil samples are reported elsewhere. A representative sample of each soil was embedded in low-viscosity epoxy, and thin sections (about 70nm thick) were obtained through ultra microtomy. The thin sections used for these analyses typically contained cross sections of up to 500 individual grains. The thin sections were studied using a JEOL 2010 transmission electron microscope (TEM) equipped with a thin window energy-dispersive X-ray (EDX) spectrometer. An individual thin section was selected from each soil, and for each grain in the section we determined (1) the elemental composition by EDX; (2) whether the grain was crystalline or glassy using electron diffraction and darkfield imaging; (3) the presence or absence of rims and accreted material; and (4) the distribution of nanophase Fe where present. Most of the categories are self-evident; however, we divide the agglutinate derived material into agglutinitic glass (glass with approximately the same composition as the bulk soil that contains nanophase Fe with or without vesicles) and agglutinate fragments, which are composed of crystalline grains and agglutinitic glass. Lithic fragments are defined as polymineralic grains with no glass. Pyroxene grains have been divided into high- and low-Ca groups. As expected, there are a number of differences in the petrography of the <10-microns fractions of 79221 and 71061 given the great difference in their respective maturities, but we focus here on two major distinctions: agglutinate content and the number of grains with micropatina. Slightly over 50% of the particles in 79221 consist of agglutinitic glass and agglutinate fragments, while the remainder are predominantly crystalline mineral grains. The agglutinic glass particles contain abundant nanophase Fe and vesicles. Angular particles are rare, with most showing smooth, rounded exteriors, Of the mineral grains analyzed thus far, over 90% of the grains have amorphous rims that contain nanophase Fe (these rims are believed to have formed by vapor deposition and irradiation effects). The nanophase Fe in these rims probably accounts for a significant fraction of the increase in Is/FeO measured in these size fractions. In addition to the rims, the majority of particles also show abundant accreted material in the form of glass splashes and spherules that also contain nanophase Fe. In stark contrast, the surfaces of the mineral grains in the 71061 sample are relatively prisitine, as only about 14% of the mineral grains in the sample exhibited amorphous rims. Furthermore, the mineral particles are more angular and show greater surface roughness than in the mature sample. Accreted material on particle surfaces is rare. Agglutinitic material is a major component of the 71061 sample; however, nanophase Fe and vesicles are not as well developed as in the 79221 sample. It is now recognized that nanophase Fe is probably the main agent in modifying the optical properties of lunar soil grains. The most important result of this study is the observation that in the fine size fractions of mature soils, nearly every grain has nanophase Fe within 100 run of the particle surface. (Additional Information contained in original)

Keller, L. P.↗

Experimental Investigation into the Radar Anomalies on the Surface of Venus

Radar mapping of thc surface of Venus shows areas of high reflectivity (low emissivity) in the Venusian highlands at altitudes between 2.5-4.75 kilometers. The origin of the radar anomalies found in the Venusian highlands remains unclear. Most explanations of the potential causes for these radar anomalies come from theoretical work. Previous studies suggest increased surface roughness or materials with higher dielectric constants as well as surface atmospheric interactions. Several possible candidates of high-dielectric materials are tellurium) ferroelectric materials, and lead or bismuth sulfides. While previous studies have been influential in determining possible sources for the Venus anomalies, only a very few hypotheses have been verified via experimentation. This work intends to experimentally constrain the source of the radar anomalies on Venus. This study proposes to investigate four possible materials that could potentially cause the high reflectivities on the surface of Venus and tests their behavior under simulated Venusian conditions.

Kohler, E.↗

Isolating the Surface Type Influence on Arctic Cloud Properties

In response to anthropogenic climate change, substantial declines in sea ice have been observed. An urgent question is whether and how clouds respond to the changing Arctic surface. Due to the important radiative influence of clouds, the response of clouds to sea ice cover change constitutes a potentially important climate feedback within the Arctic. The sign of this feedback is strongly influenced by the seasonality of the cloud response to sea ice loss. Given the importance of this phenomenon, previous research focused on using observations of inter-annual variability to quantify the cloud-sea ice relationship. However, the reliance on inter-annual variability to assess the covariance between clouds and sea ice make it challenging to control for the influence of large-scale meteorology on the clouds. We have devised an approach that applies an in situ, airborne observational strategy to quantify the influence of surface type on Arctic clouds to satellite data. Our event-based method composites cloud property differences for ocean, marginal ice zone, and sea ice surface types for >5000 MIZ crossing events. We find that cloud properties in non-summer months below ~1.5 km are influenced by surface type such that greater cloud fraction and water content are found over ocean relative to sea ice regions. Results are statistically significantly at the 95% confidence level. During summer, the surface type does not influence the cloud properties. The primary cause of the surface type dependent cloud property differences is the thermodynamic profiles differences that occur between the two surface types: namely, ocean footprints are warmer, moister, have more positive surface turbulent fluxes and are less stable than their sea ice counterparts. We find that the differences in thermodynamic profiles by surface type that correspond to the cloud property differences also explains a significant portion of the variability across events. Our analysis provides evidence that the influence of surface type on cloud properties fundamentally occurs due to the inherent surface temperature differences between the surface types. Significant surface type influences on cloud properties are only found in the presence of surface temperature differences between the surface types and only non-summer months meet this criterion. A conceptual model of this process is as follows, fundamental properties of the ocean and sea ice surface types (e.g., surface albedo, heat capacity/thermal inertia, surface roughness, and thermal conductance) lead to systematic differences in the surface temperature by surface type. In response to this surface temperature difference, atmosphere boundary layer processes (including turbulent mixing and radiation) communicate the surface temperature differences to the lower atmosphere driving the greater stability over sea ice than ocean. These differences in the background thermodynamic state profiles between the surface types yield atmospheric conditions that are more conducive to cloud development over ocean than sea ice. The details of these boundary layer processes are sensitive to the surface type but may not be fundamental to the resulting thermodynamic structure and cloud differences. Thus, our results indicate that to accurately model that cloud response to sea ice loss in climate models the surface type properties that yield the systematic differences in ocean and sea ice temperature (e.g., surface albedo, surface turbulent fluxes parameters, and thermal conductance) must be accurately represented.

Arctic radiation budget↗

Optical properties of sputtered aluminum on graphite/epoxy composite material

Solar absorptance, emittance, and coating thickness were measured for a range of coating thicknesses from about 400 A to 2500 A. The coatings were sputtered from an aluminum target onto 1-inch-diameter substrates of T300/5209 graphite/epoxy composite material with two different surface textures. Solar absorptance and emittance values for the specimens with the smooth surface finish were lower than those for the specimens with the rough surface finish. The ratio of solar absorptance to emittance was higher for the smooth specimens, increasing from 2 to 4 over the coating thickness range, than for the rough ones, which had a constant ratio of about 1. The solar absorptance and emittance values were dependent on the thickness of the sputtered coating.

Witte, William G., Jr.↗

Three dimensional numerical scattering from ocean-like surfaces

A new method of calculating the electric field scattered from two-dimensional conducting rough surfaces is presented. This method uses the operator conjugate gradients technique and the extended boundary condition equation. This avoids the build-up of round-off errors encountered in the inversion of large matrices. It also avoids the singularities of the integral kernels usually encountered in the method of moments. Techniques for improving the rate of convergence by applying physical constraints are discussed. This method is presently being used to calculate the polarization signatures from simulated ocean-like surfaces.

Rodriguez, Ernesto↗

ESM Roughness Datasets (ARC)

This work focused on the effects on turbulent heat transfer due to surface roughness of types relevant to NASA entry missions, and was supported by NASA’s Entry Systems Modeling (ESM) Project. The emphasis was on new classes of woven materials, which are enabling for many missions.

heat transfer↗

Evaluation of transfer films of Salox M on 440C for HPOTP bearing cage applications, task 119

The objective of the task was to evaluate the suitability of a bronze-filled polytetra fluoroethylene (Salox M) as the cage material in Space Shuttle Main Engine (SSME) high pressure oxygen turbo pump (HPOTP) bearings. The role of the cage pocket material will be to provide a transferred lubricating interface at the ball-race contact region. A series of experiments was conducted which involved block-on-ring tests (the block was the polytetrafluoroethylene (PTFE) -filled material and the ring was through-hardened 440C steel) and high speed traction tests of two 440C disks with one disk rubbed with a PTFE block to generate a transfer film. Measurements included post test visual observations of the condition of the 440C, wear rate measurements of the blocks, and traction measurements between the disks. It was observed that both Salox M and glass-filled PTFE (Armalon) transferred PTFE to 440C at cryogenic temperatures. Bronze is also transferred to uncoated 440C from the Salox M. At room temperature no PTFE transfer was observed in the high speed disk tests due to severe frictional heating, although bronze transfer still occurred with the bronze-PTFE Salox M material. Since the bearing will operate at cryogenic temperature, transfer films are very probable. Salox M wore slightly, although probably tolerably, more than glass-filled PTFE against 440C. However, Salox M is clearly less abrasive to 440C than is the glass-filled material. When the surface layer of PTFE is depleted from the glass-filled material, the glass fibers tend to seriously abrade the steel. This problem does not occur with Salox M. The surface roughness studies indicate that smooth balls are quite reasonable for transfer films. No significant difference in wear rates of the candidate cage materials was observed when the 440C surface finish was increased from 0.025 micron to 0.1 micron cla. At higher levels of roughness, the wear rate increased. Two surface coatings (MoS2 and TiN) were tested. The surface coatings tended to reduce the Salox M wear rate and reduce bronze transfer. PTFE transfer at cryogenic temperatures still occurred with the surface coatings. Two cage design concepts are presented utilizing Salox M material. One design involves a metal-reinforced Salox M cage, while the second design uses Salox M inserts in a metal structure.

Barber, S. A.↗

Comparison of quasi-specular radar scatter from the moon with surface parameters obtained from images

Quasi-specular radar scatter from geologic surfaces displays a variable wavelength dependence in apparent surface roughness. Wavelength dependence will occur whenever a significant fraction of the surface has local radii of curvature comparable to the observing wavelength. This condition can be determined by comparison of the value of the integrated surface curvature spectrum with the radar wavenumber, multiplied by a constant that depends on the geometry. Variations in curvature statistics calculated from photogrammetric reduction of lunar images are consistent with the observed variations in quasi-specular scatter at the same locations. Variations in the strength of the wavelength dependence are correlated with the sizes of lunar craters that lie near the upper size limit for the local steady state distribution. This correlation is also consistent with variations in the curvature spectrum calculated from crater size-frequency distributions.

Tyler, G. L.↗

Analysis of 12-700 micron reflectance spectra of three optical black samples

Normal incidence, specular reflectance spectra of three samples of optical black coatings have been measured in 10 filter passbands at effective wavelengths between 12 and 700 microns. Strong absorption, due to amorphous silicate material in the coatings, is found in the 15-50 micron region of each spectrum. Reflecting-layer model calculations are fitted by a nonlinear least-squares routine to the spectra at wavelengths beyond the absorption band to determine far-infrared optical parameters. It is found that, with a similar wavelength dependence, the absorption coefficient of a new black coating (ECP 2200) made by the Minnesota Mining and Manufacturing Company (3M) is less than 1/10 that of the discontinued coating, 3M Black Velvet Nextel. It is also shown that the extinction effect of a very rough substrate is negligible compared with the effects of increased upper surface roughness and coating thickness attendant upon fully covering a very rough substrate.

Smith, S. M.↗