Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “structural modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39
All sourcesNASA NTRSDOE OSTI
NASA NTRS2011

Lateral-Directional Parameter Estimation on the X-48B Aircraft Using an Abstracted, Multi-Objective Effector Model

The problem of parameter estimation on hybrid-wing-body aircraft is complicated by the fact that many design candidates for such aircraft involve a large number of aerodynamic control effectors that act in coplanar motion. This adds to the complexity already present in the parameter estimation problem for any aircraft with a closed-loop control system. Decorrelation of flight and simulation data must be performed in order to ascertain individual surface derivatives with any sort of mathematical confidence. Non-standard control surface configurations, such as clamshell surfaces and drag-rudder modes, further complicate the modeling task. In this paper, time-decorrelation techniques are applied to a model structure selected through stepwise regression for simulated and flight-generated lateral-directional parameter estimation data. A virtual effector model that uses mathematical abstractions to describe the multi-axis effects of clamshell surfaces is developed and applied. Comparisons are made between time history reconstructions and observed data in order to assess the accuracy of the regression model. The Cram r-Rao lower bounds of the estimated parameters are used to assess the uncertainty of the regression model relative to alternative models. Stepwise regression was found to be a useful technique for lateral-directional model design for hybrid-wing-body aircraft, as suggested by available flight data. Based on the results of this study, linear regression parameter estimation methods using abstracted effectors are expected to perform well for hybrid-wing-body aircraft properly equipped for the task.

Ratnayake, Nalin A.↗
NASA NTRS1996

Integrated Modeling Methodology Validation Using the Micro-Precision Interferometer Testbed

This paper validates the integrated modeling methodology used for design and performance evaluation of complex opto-mechanical systems, particularly spaceborne interferometers. The methodology integrates structural modeling, optical modeling, and control system design into a common environment, the Integrated Modeling of Optical Systems (IMOS) software package.

opto-mechanical↗
NASA NTRS1996

Development and Application of Viscoplastic Models in Nonlinear Structural Analysis

A number of numerical solution technologies were developed for advanced analysis capabilities involving the finite element method in advanced constitutive modeling and structural analysis for improved and rational designs of aerospace propulsive systems. These technologies were incorporated into several advanced viscoplastic models and were applied to a wide spectrum of structural engineering problems involving extremes of thermal/mechanical loading. Results of the research performed under the grant were presented at a number of scientific meetings and conferences and have resulted in numerous publications.

Keith, Theo G., Jr.↗
NASA NTRS1985

A demonstrative model of a lunar base simulation on a personal computer

The initial demonstration model of a lunar base simulation is described. This initial model was developed on the personal computer level to demonstrate feasibility and technique before proceeding to a larger computer-based model. Lotus Symphony Version 1.1 software was used to base the demonstration model on an personal computer with an MS-DOS operating system. The personal computer-based model determined the applicability of lunar base modeling techniques developed at an LSPI/NASA workshop. In addition, the personnal computer-based demonstration model defined a modeling structure that could be employed on a larger, more comprehensive VAX-based lunar base simulation. Refinement of this personal computer model and the development of a VAX-based model is planned in the near future.

Source record↗
NASA NTRS1989

Full potential unsteady computations including aeroelastic effects

A unified formulation is presented based on the full potential framework coupled with an appropriate structural model to compute steady and unsteady flows over rigid and flexible configurations across the Mach number range. The unsteady form of the full potential equation in conservation form is solved using an implicit scheme maintaining time accuracy through internal Newton iterations. A flux biasing procedure based on the unsteady sonic reference conditions is implemented to compute hyperbolic regions with moving sonic and shock surfaces. The wake behind a trailing edge is modeled using a mathematical cut across which the pressure is satisfied to be continuous by solving an appropriate vorticity convection equation. An aeroelastic model based on the generalized modal deflection approach interacts with the nonlinear aerodynamics and includes both static as well as dynamic structural analyses capability. Results are presented for rigid and flexible configurations at different Mach numbers ranging from subsonic to supersonic conditions. The dynamic response of a flexible wing below and above its flutter point is demonstrated.

Shankar, Vijaya↗
NASA NTRS1991

Vibration analysis of the SA349/2 helicopter

Helicopter airframe vibration is examined using calculations and measurements for the SA349/2 research helicopter. The hub loads, which transmit excitations to the fuselage, are predicted using a comprehensive rotorcraft analysis and correlated with measuring hub loads. The predicted and measured hub loads are then coupled with finite element models representing the SA349/2 fuselage. The resulting vertical acceleration at the pilot seat is examined. Adjustments are made to the airframe structural models to examine the sensitivity of predicted vertical acceleration to the model. Changes of a few percent to the damping and frequency of specific models lead to large reductions in predicted vibration, and to major improvements in the correlations with measured pilot-seat vertical acceleration.

Heffernan, Ruth↗
NASA NTRS1991

Analysis and correlation of SA349/2 helicopter vibration

Helicopter airframe vibration is examined using calculation and measurements for the SA349/2 research helicopter. The hub loads, which transmit excitation to the fuselage, are predicted using a comprehensive rotorcraft analysis and correlated with measured hub loads. The predicted and measured hub loads are then coupled with finite element models representing the SA349/2 fuselage. The resulting vertical acceleration at the pilot seat is examined. Adjustments are made to the airframe structural models to examine the sensitivity of predicted vertical acceleration to the model. Changes of a few percent to the damping and frequency of specific modes lead to large reductions in predicted vibration and to major improvements in the correlations with measured pilot seat vertical acceleration.

Heffernan, Ruth↗
NASA NTRS1991

Vibration suppression using a proofmass actuator operating in stroke/force saturation

The design of the control-loop structure for a feedback control system which contains a proofmass actuator for suppressing vibration is discussed. The loop structure is composed of inner control loops, which determine the frequency of the actuator and which are directly related to the actuator and the outer loops which add damping to the structure. When the frequency response of the actuator is matched to the stroke/force saturation curve, the actuator is most effective in the vibration suppression loops, and, since the stroke/force saturation curve is characterized by the stroke length, the mass of the proofmass, and the maximum current delivered by the motor electronics, the size of the actuator can be easily determined. The results of the loop-structure model calculations are verified by examining linear DC motors as proofmass actuators for the Mast in NASA's Control of Flexible Structures program.

Lindner, D. K.↗
NASA NTRS2004

Inducer Hydrodynamic Forces in a Cavitating Environment

Marshall Space Flight Center has developed and demonstrated a measurement device for sensing and resolving the hydrodynamic loads on fluid machinery. The device - a derivative of the six-component wind tunnel balance - senses the forces and moments on the rotating device through a weakened shaft section instrumented with a series of strain gauges. This rotating balance was designed to directly measure the steady and unsteady hydrodynamic loads on an inducer, thereby defining the amplitude and frequency content associated with operating in various cavitation modes. The rotating balance was calibrated statically using a dead-weight load system in order to generate the 6 x 12 calibration matrix later used to convert measured voltages to engineering units. Structural modeling suggested that the rotating assembly first bending mode would be significantly reduced with the balance s inclusion. This reduction in structural stiffness was later confirmed experimentally with a hammer-impact test. This effect, coupled with the relatively large damping associated with the rotating balance waterproofing material, limited the device s bandwidth to approximately 50 Hertz Other pre-test validations included sensing the test article rotating assembly built-in imbalance for two configurations and directly measuring the assembly mass and buoyancy while submerged under water. Both tests matched predictions and confirmed the device s sensitivity while stationary and rotating. The rotating balance was then demonstrated in a water test of a full-scale Space Shuttle Main Engine high-pressure liquid oxygen pump inducer. Experimental data was collected a scaled operating conditions at three flow coefficients across a range of cavitation numbers for the single inducer geometry and radial clearance. Two distinct cavitation modes were observed symmetric tip vortex cavitation and alternate-blade cavitation. Although previous experimental tests on the same inducer demonstrated two additional cavitation modes at lower inlet pressures, these conditions proved unreachable with the rotating balance installed due to the intense dynamic environment. The sensed radial load was less influenced by flow coefficient than by cavitation number or cavitation mode although the flow coefficient range was relatively narrow. Transition from symmetric tip vortex to alternate-blade cavitation corresponded to changes in both radial load magnitude and radial load orientation relative to the inducer. Sensed moments indicated that the effective load center moved downstream during this change in cavitation mode. An occurrence of "higher+rdex cavitation" was also detected in both the stationary pressures and the rotating balance data although the frequency of the phenomena was well above the reliable bandwidth of the rotating balance. In summary the experimental tests proved both the concept and device s capability despite the limitations and confirmed that hydrodynamically-induced forces and moments develop in response to the unbalanced pressure field, which is, in turn, a product of the cavitation environment.

Skelley, Stephen E.↗
NASA NTRS2013

Uncertainty in Simulating Wheat Yields Under Climate Change

Projections of climate change impacts on crop yields are inherently uncertain1. Uncertainty is often quantified when projecting future greenhouse gas emissions and their influence on climate2. However, multi-model uncertainty analysis of crop responses to climate change is rare because systematic and objective comparisons among process-based crop simulation models1,3 are difficult4. Here we present the largest standardized model intercomparison for climate change impacts so far. We found that individual crop models are able to simulate measured wheat grain yields accurately under a range of environments, particularly if the input information is sufficient. However, simulated climate change impacts vary across models owing to differences in model structures and parameter values. A greater proportion of the uncertainty in climate change impact projections was due to variations among crop models than to variations among downscaled general circulation models. Uncertainties in simulated impacts increased with CO2 concentrations and associated warming. These impact uncertainties can be reduced by improving temperature and CO2 relationships in models and better quantified through use of multi-model ensembles. Less uncertainty in describing how climate change may affect agricultural productivity will aid adaptation strategy development and policymaking.

exhaust gases↗
NASA NTRSDate not supplied

Assessment of Artemis-1 Pogo Flight Instrumentation System

As the space industry continues to strive for more efficient launch vehicles, it must relyon increasingly accurate predictive models. Verification of models typically requires physical testing. Flight data measurements offer the most real and therefore the most accurate data for model correlation. As NASA prepares for the inaugural launch of Space Launch System(SLS), Artemis-1, they must rely heavily on predictive system models to ensure flight safety.NASA has implemented a Development Flight Instrumentation (DFI) system in hopes of recovering useful flight data to aid in model correlation. Historically, some of the most important flight measurements are those that monitor the potentially destructive dynamic interaction of the structural and propellant modes – a phenomenon known as pogo. Pogo is a dynamic instability that can occur on a launch vehicle during any phase of ascent. During this investigation an end-to-end assessment of the Artemis-I Pogo-related DFI was performed to identify any obstacles inherent in the current instrumentation system which may prevent successful measurement of the data necessary to validate the current predictive fluid-structural models. Input drive signals were approximated and applied to a state-space system model to derive predicted pressure and acceleration responses. These predicted responses were then fed through a simulation of the data acquisition process in order to recover predicted measurements. Finally, a mock Flight Data Analysis (FDA) was performed to assess the ability of these measurements to meet the Flight Test Objectives(FTO).

Adam Johnson↗
NASA NTRS1999

The 13th Technology of Deep Space One

On October 24th, 1998, the Deep Space One (DS-1) spacecraft launched aboard a Delta II rocket as the first step towards the bold task of testing and validating 12 new technologies for future missions. This launch also represented yet another thrilling event; namely, the successful test and validation of a 13th heretofore undisclosed technology: model-base-code-generation of the spacecraft's system-level fault-protection (FP) software from behavioral state diagrams and structural models.

model-based-code-generation↗
NASA NTRS1992

Katz model prediction of Caenorhabditis elegans mutagenesis on STS-42

Response parameters that describe the production of recessive lethal mutations in C. elegans from ionizing radiation are obtained with the Katz track structure model. The authors used models of the space radiation environment and radiation transport to predict and discuss mutation rates for C. elegans on the IML-1 experiment aboard STS-42.

Cucinotta, Francis A.↗
NASA NTRS1992

Experimental and analytical study of the effects of floor location on response of composite fuselage frames

Experimental and analytical results are presented of the effects of floor placement on the structural response and strength of I-cross section, semi-circular fuselage frames constructed of graphite-epoxy composite material. The composite frame configuration is representative of current conventional aircraft design. Experimental strain distributions are presented from static loading tests of the composite frames and compared with finite element structural models and closed form solutions. An understanding of floor location effects can aid dynamists in predicting the crash behavior of these conventional structures, and may assist the designer in developing crashworthy structures for future aircraft.

Jones, Lisa E.↗
NASA NTRS2012

A Cross-Validation Approach to Approximate Basis Function Selection of the Stall Flutter Response of a Rectangular Wing in a Wind Tunnel

The stall flutter response of a rectangular wing in a low speed wind tunnel is modelled using a nonlinear difference equation description. Static and dynamic tests are used to select a suitable model structure and basis function. Bifurcation criteria such as the Hopf condition and vibration amplitude variation with airspeed were used to ensure the model was representative of experimentally measured stall flutter phenomena. Dynamic test data were used to estimate model parameters and estimate an approximate basis function.

Kukreja, Sunil L.↗
NASA NTRS1982

Stress analysis and design considerations for Shuttle pointed autonomous research tool for astronomy /SPARTAN/

The Shuttle Pointed Autonomous Research Tool for Astronomy (SPARTAN) family of spacecraft are intended to operate with minimum interfaces with the U.S. Space Shuttle in order to increase flight opportunities. The SPARTAN I Spacecraft was designed to enhance structural capabilities and increase reliability. The approach followed results from work experience which evolved from sounding rocket projects. Structural models were developed to do the analyses necessary to satisfy safety requirements for Shuttle hardware. A loads analysis must also be performed. Stress analysis calculations will be performed on the main structural elements and subcomponents. Attention is given to design considerations and program definition, the schematic representation of a finite element model used for SPARTAN I spacecraft, details of loads analysis, the stress analysis, and fracture mechanics plan implications.

Ferragut, N. J.↗