Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “stress testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

An investigation into the effects of cyclic strain rate on the high cycle and very high cycle fatigue behaviors of wrought and additively manufactured Inconel 718

Additive Manufacturing (AM) has increasingly been used to fabricate parts in aerospace applications, which may require service lives beyond ten-million cycles due to the imposed high loading frequencies. Understanding the very high cycle fatigue (VHCF) behavior of these additive manufactured (AM) parts is an important step towards their design and qualification processes. This study focuses on the high cycle fatigue (HCF) and VHCF behaviors of both wrought and laser beam-powder bed fusion (LB-PBF) fabricated Inconel 718 in machined/polished surface condition, emphasizing on the influence of test frequency (i.e., cyclic strain rate). Uniaxial, fully-reversed force- and stress-controlled fatigue tests were conducted utilizing a servo-hydraulic and an ultrasonic test system operating at 5 Hz and 20 kHz, respectively, on wrought as well as LB-PBF vertically and diagonally built specimens. Fatigue cracks in the majority of the specimens were found to initiate from intra-granular slip bands near or at the surface, which gives rise to strong anisotropy in fatigue resistance in LB-PBF specimens due to the presence of columnar grains along the build directions. Longer fatigue lives were obtained at 20 kHz, which was ascribed to possibly lower-than-intended stresses applied in the ultrasonic tests. The corrected stress-life fatigue data at 20 kHz were found to converge to the one obtained from conventional testing at 5 Hz, implying no effect of cyclic strain rate on the fatigue behavior of Inconel 718 regardless of the fabrication process. The findings of this work confirm the use of ultrasonic fatigue testing to expedite generation of AM materials data to keep up with the current demand; however, the applied stress may need to be corrected.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Increasing the Pressure‐Free Stripping Capacity of the Lithium Metal Anode in Solid‐State‐Batteries by Carbon Nanotubes

Abstract Lithium metal is the key anode material for solid‐state‐batteries as its successful implementation will drastically increase their energy and power densities. However, anode contact loss during stripping leads to dendrites upon plating and subsequent cell failure. Design strategies to mitigate these issues are crucial to enable the use of lithium metal anodes. This paper reports the dissolution kinetics of composite anodes made of lithium metal and carbon nanotubes (CNTs) with a garnet‐type solid electrolyte (SE). In addition to an enhancement of the effective diffusion within the anode, its dissolution is fundamentally changed from being 2D to 3D. By maintaining contact with the SE, the CNTs facilitate lithium transport to the interface, which yields more than 20 mAh cm −2 discharge capacity at 100 µ A cm −2 without the application of external stack pressure ( > 1 MPa). Conclusions drawn from electrochemical data on the anode microstructure are validated using cryo‐focused‐ion‐beam scanning electron microscopy and correlated with the mechanical properties. Micro‐indentation, acoustic analysis, and stress–strain testing show that mechanical properties of the anode, like yield strength and hardness, are adjustable. Overall, it is shown that the mechanical and electrochemical properties of Li–CNT composite electrodes can be tailored to suit the requirements of a practical cell.

Fuchs, Till↗
DOE OSTI2022

Stress-controlled fatigue of HfNbTaTiZr high-entropy alloy and associated deformation and fracture mechanisms

The stress-controlled fatigue tests are carried out at a stress ratio of 0.1 and a frequency of 10 Hz, and span both low-cycle and high-cycle regimes by varying the applied stress amplitudes. The high-cycle fatigue regime gives a fatigue strength of 497 MPa and a fatigue ratio of 0.44. At equivalent conditions, the alloy's fatigue strength is greater than all other high-entropy alloys (HEAs) with reported high-cycle fatigue data, dilute body-centered cubic alloys, and many structural alloys such as steels, titanium alloys, and aluminum alloys. Through in-depth analyses of crack-propagation trajectories, fracture-surface morphologies and deformation plasticity by means of various microstructural analysis techniques and theoretical frameworks, the alloy's remarkable fatigue resistance is attributed to delayed crack initiation in the high-cycle regime, which is achieved by retarding the formation of localized persistent slip bands, and its good resistance to crack propagation in the low-cycle regime, which is accomplished by intrinsic toughening backed up by extrinsic toughening. Additionally, the stochastic nature of the fatigue data is neatly captured with a 2-parameter Weibull model.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Strain age cracking in a simulated heat affected zone of Inconel 740H laser-powder bed fusion components

Inconel® 740H components produced via laser-powder-bed fusion (L-PBF) additive manufacturing are ideal for supercritical CO2 primary heat exchangers. Arc welding is often needed, and subsequent post-weld heat treatment aging at 790–840 °C is required to improve strength via gamma prime (γ’) precipitation; however, strain age cracking (SAC) can occur in the heat affected zone (HAZ) during this process. This study uses stress relaxation testing at 800 °C on simulated HAZ specimens from vertically and horizontally built L-PBF IN740H to assess SAC susceptibility across heating rates of 40–3480 °C/h and weld-induced strains of 3–10 %. Vertical builds require greater mechanical energy input and exhibit longer times to fracture than horizontal builds, and time to fracture occurs sooner at slower heating rates. Creep voids were observed in γ’-denuded regions along grain boundaries, and cracking propagated along migrated grain boundaries and at interfaces between elongated secondary phases (γ’ or carbides) and the γ-matrix.

14 SOLAR ENERGY↗
DOE OSTI2020

Analysis of alternative climate datasets and evapotranspiration methods for the Upper Mississippi River Basin using SWAT within HAWQS

This study reports the application of Soil andWater Assessment Tool (SWAT) within the Hydrologic andWater Quality System(HAWQS) on-line platform, for the UpperMississippi River Basin (UMRB). TheUMRB is an important ecosystem located in the north central U.S. that is experiencing a range of ecological stresses. Specifically, testing of SWAT was performed for: (1) Hargreaves (HG) and Penman-Monteith (PM) PET methods, and (2) Livneh, National Climatic Data Center (NCDC) and Parameter-elevation Regressions on Independent Slopes Model (PRISM) climate datasets. The Livneh-PM combination resulted in the highest average annual water yield of 380.6 mm versus the lowest estimated water yield of 193.9 mm for the Livneh-HG combination, in response to 23-year uncalibrated simulations. Higher annual ET and PET values were predicted with HG method versus the PM method for all three weather datasets in response to the uncalibrated simulations, due primarily to higher HG-based estimates during the growing season. Based on these results, it was found that the HG method is the preferred PET option for the UMRB. Initial calibration of SWAT was performed using the Livneh data and HGmethod for threeMississippi Rivermain stem gauge sites, which was followed by spatial validation at 10 other gauge sites located within the UMRB streamnetwork. Overall satisfactory results were found for the calibration and validation gauge sites, with the majority of R2 values ranging between 0.61 and 0.82, Nash- Sutcliffe modeling efficiency (NSE) values ranging between 0.50 and 0.79, and Kling-Gupta efficiency (KGE) values ranging between 0.61 and 0.84. The results of an additional experimental suite of six scenarios,which represented different combinations of climate data sets and calibrated parameters, revealed that suggested statistical criteria were again satisfied by the different scenario combinations. Overall, the PRISM data exhibited the strongest reliability for the UMRB.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Degradation behavior of CIGS solar Cells: A parametric analysis

A parametric study of the effect of bulk and interface properties on device characteristics as a function of heat and light stress under open-circuit and short-circuit conditions is developed for Cu(In,Ga)(S,Se) 2 solar cells using SCAPS-1D simulator. The variables and interdependencies modeled include: (1) conduction band offset (CBO) between buffer and absorber; (2) buffer ionized donor density; (3) CIGS shallow acceptor density; (4) CIGS deep acceptor density; (5) CIGS shallow donor density; (6) ionized acceptor concentration in the ordered vacancy compound (OVC) CIGS/buffer interface; and (7) back contact work-function. An increase in absorber shallow acceptor or a decrease in shallow donor density results in an increase in net carrier density and open-circuit voltage (V OC ). Further, a decrease in V OC is observed with an increase in the deep acceptors or neutral midgap defects in the CIGS due to higher charge carrier recombination. A change of CBO from spike to cliff condition is a dominant mechanism of decreasing VOC with an interface defect density of 10 12 cm -2 . The minimum depletion width is found to be specifically sensitive to CBO and interface defect density. An inflection in the capacitance–voltage curves (in reverse bias) is observed with simultaneous increase in bulk deep acceptor density and shallow donor density near the back contact.

14 SOLAR ENERGY↗
DOE OSTI2022

Asymmetric Miktoarm Star Polymers as Polyester Thermoplastic Elastomers

A library of polyester-based A(BA') n asymmetric miktoarm star polymers was synthesized with A, A' = poly(l-lactide) (PLLA) as the semicrystalline hard blocks and B = poly(4-methylcaprolactone) (PMCL) as the soft segment using a grafting-through platform known as μSTAR. The synthetic versatility of μSTAR enabled a systematic investigation of architectural design parameters, in particular the number of BA' arms (n), while holding the A, A', and B block lengths constant. The value of n has a pronounced impact on the mechanical properties of these high-molecular-weight miktoarm materials. Tensile toughness increases with n, an effect likely related to bridging, as the modulus drops because the hard-block volume fraction decreases. Furthermore, these insights expand our understanding of architecture effects in sustainable thermoplastic elastomers.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Monotonic Gaussian Process for Physics-Constrained Machine Learning With Materials Science Applications

Physics-constrained machine learning is emerging as an important topic in the field of machine learning for physics. One of the most significant advantages of incorporating physics constraints into machine learning methods is that the resulting model requires significantly less data to train. By incorporating physical rules into the machine learning formulation itself, the predictions are expected to be physically plausible. Gaussian process (GP) is perhaps one of the most common methods in machine learning for small datasets. In this paper, we investigate the possibility of constraining a GP formulation with monotonicity on three different material datasets, where one experimental and two computational datasets are used. The monotonic GP is compared against the regular GP, where a significant reduction in the posterior variance is observed. The monotonic GP is strictly monotonic in the interpolation regime, but in the extrapolation regime, the monotonic effect starts fading away as one goes beyond the training dataset. Imposing monotonicity on the GP comes at a small accuracy cost, compared to the regular GP. The monotonic GP is perhaps most useful in applications where data are scarce and noisy, and monotonicity is supported by strong physical evidence.

36 MATERIALS SCIENCE↗
DOE OSTI2021

AST Development for PEM Electrolyzers [Slides]

The ASTWG charter targets include: Develop ASTs to predict 80,000 hours of life in desired application; and Develop additional ASTs to evaluate different PEM electrolyzer components.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2020

Examination of Gamma-irradiated Calcium Silicate Hydrates. Part II: Mechanical Properties

Mechanical properties of calcium silicate hydrates (C-S-H) with C/S ratios of 0.75, 1, and 1.33 were examined with nanoindentation after gamma-adsorbed doses of 0.145, 0.280, 0.500, and 0.784 MGy, and were compared with control samples. Young' s modulus and stress relaxation tests showed no apparent trend with irradiation dose. Qualitatively, most of the irradiated samples were found to relax more than their respective controls, but not always in a statistically significant manner. Most of the Young' s modulus irradiated–control pairs showed marginally higher stiffness in the irradiated samples, but overall trends with irradiation dose were not obvious. Creep compliance was obtained for the samples irradiated at the highest dose and their respective controls. Two of the three irradiated samples exhibited less creep than their respective controls, but only one of which was statistically significant. The lack of clear changes in mechanical properties for these samples correlates with separate chemical analyses that showed no loss of interlayer water by exposure to irradiation or changes in the mean silicate chain length. Further research evaluating higher doses (25 and 200 MGy) representative of those received by concrete structures in nuclear power plants at prolonged operation is being carried out to complement the present study.

36 MATERIALS SCIENCE↗
NASA NTRS1964

Bearing transmits rotary and axial motion

A low friction, two-component bearing comprised of a pair of ball-bearing races for transmitting rotary motion and an inner series of ball bearing assemblies for transmitting axial motion is described and should be useful in mechanisms such as stress-strain testing machines.

Dow, N. F.↗
NASA NTRS1963

Component design, construction and evaluation for satellites

Components for a high-reliability system such as the Telstar project are obtained by: (a) design of the component for the required environment, (b) careful control of manufacturing processes, (c) elimination of potential early failures by screening tests, and (d) selection of the most stable components. For passive components, these methods could be applied by using design parameters, suppliers and screening techniques established in the earlier submarine cable program, with consideration being given to the additional effects of the satellite launch and orbit environments. Semiconductor component designs were selected by qualification tests using accelerated electrical and environmental stress conditions. Screening tests were applied to eliminate early failures, and resulting components were aged from two to six months before selection for the satellite. The recognition of the effect of ionizing radiation on transistors caused the addition of a radiation qualification test, or a screening to assure selection of the least sensitive devices. Tests have shown this screening to be effective for the radiation intensity expected. Experience with the passive components, and evaluation of the accelerated test results and aging data of the semiconductor devices, indicate that the reliability objective was obtained.

TELSTAR SATELLITE↗
NASA NTRS1965

Development of high temperature nickel-base alloys for jet engine turbine bucket applications

A program has been initiated to develop a material with superior properties at elevated temperatures for utilization in turbine blade applications. A nickel-base superalloy can provide the necessary high temperature strength by using the maximum capability of the three available strengthening mechanisms - intermetallic gamma prime precipitation (Ni3Al), solid solution strengthening with refractory and precious metals, and stable carbide formations through the addition of strong carbide forming elements. A stress rupture test at 2000 deg F and 15,000 psi was formulated to approximate the desired properties. By adding varying amounts of refractory metals (Mo, W and Ta) it was possible to statistically analyze the effects of each in a basic superalloy composition containing fixed amounts of Co, Cr, C, B, Sr, and Ni at three separate levels of AL and Ta. Metallographic analysis correlated with the mechanical properties of the alloys; those with few strengthening phases were weak and ductile and those with excessive amounts of intermetallic phases present in undesirable morphologies were brittle.

SUPERALLOY↗
NASA NTRS1966

Research Achievements Review, volume II

Materials research - diffusion bonding methods, stress corrosion tests, nondestructive testing, material designs for electronic equipment, and nonmetallic material development.

SPACECRAFT COMPONENT↗