Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “spectral methods”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 703 records · Page 39
All sourcesNASA NTRSDOE OSTI
NASA NTRS2008

Shaping Diffraction-Grating Grooves to Optimize Efficiency

A method of shaping diffraction-grating grooves to optimize the spectral efficiency, spectral range, and image quality of a spectral imaging instrument is under development. The method is based on the use of an advanced design algorithm to determine the possibly complex shape of grooves needed to obtain a desired efficiency-versus-wavelength response (see figure). Then electron- beam fabrication techniques are used to realize the required groove shape. The method could be used, for example, to make the spectral efficiency of the grating in a given wavelength range proportional to the inverse of the spectral efficiency of a photodetector array so that the overall spectral efficiency of the combination of the grating and the photodetector array would be flat. The method has thus far been applied to one-dimensional gratings only, but in principle, it is also applicable to two-dimensional gratings. The algorithm involves calculations in the spatial-frequency domain. The spatial-frequency spectrum of a grating is represented as a diffraction-order spectral-peak-width function multiplied by an efficiency function for a single grating groove. This representation affords computational efficiency and accuracy by making it possible to consider only the response from one grating groove (one period of the grating), instead of from the whole grating area, in determining the response from the entire grating. This combination of efficiency and accuracy is crucial for future extensions of the algorithm to two-dimensional designs and to designs in which polarization must also be taken into account. The algorithm begins with the definition of target values of relative efficiency that represent the desired spectral response of the grating in certain spectral frequencies calculated from the diffraction order and wavelength. The grating period is divided into a number of cells - typically, 100. The phase contribution from each cell is determined from the phase of the incident electromagnetic wave and the height of the grating surface in the cell. The total contribution from all cells to each target value is then calculated. Then a method known to specialists as the optimum-rotation-angle method is used to adjust the height of each cell so that the total response from all cells is optimized. The computation is iterative and continues until the desired response is obtained. In the event that the desired response is unphysical, the algorithm nevertheless strives to generate a grating-grove profile for which the response approximates the desired one as closely as possible.

Backlund, John↗
NASA NTRS1989

Identification of XV-15 aeroelastic modes using frequency-domain methods

The XV-15 Tilt-Rotor wing has six major aeroelastic modes that are close in frequency. To precisely excite individual modes during flight test, dual flaperon exciters with automatic frequency-sweep controls were installed. The resulting structural data were analyzed in the frequency domain (Fourier transformed) with cross spectral and transfer function methods. Modal frequencies and damping were determined by performing curve fits to transfer function magnitude and phase data and to cross spectral magnitude data. Results are given for the XV-15 with its original metal rotor blades. Frequency and damping values are also compared with earlier predictions.

Acree, C. W., Jr.↗
NASA NTRS1989

Identification of XV-15 aeroelastic modes using frequency-domain methods

The XV-15 Tilt-Rotor wing has six major aeroelastic modes that are close in frequency. To precisely excite individual modes during flight test, dual flaperon exciters with automatic frequency-sweep controls were installed. The resulting structural data were analyzed in the frequency domain (Fourier transformed) with cross spectral and transfer function methods. Modal frequencies and damping were determined by performing curve fits to transfer function magnitude and phase data and to cross spectral magnitude data. Results are given for the XV-15 with its original metal rotor blades. Frequency and damping values are also compared with earlier predictions.

Acree, Cecil W., Jr.↗
NASA NTRS1973

On Digital Simulation of Multicorrelated Random Processes and Its Applications

Two methods are described to simulate, on a digital computer, a set of correlated, stationary, and Gaussian time series with zero mean from the given matrix of power spectral densities and cross spectral densities. The first method is based upon trigonometric series with random amplitudes and deterministic phase angles. The random amplitudes are generated by using a standard random number generator subroutine. An example is given which corresponds to three components of wind velocities at two different spatial locations for a total of six correlated time series. In the second method, the whole process is carried out using the Fast Fourier Transform approach. This method gives more accurate results and works about twenty times faster for a set of six correlated time series.

Sinha, A. K.↗
NASA NTRS1987

Using frequency-domain methods to identify XV-15 aeroelastic modes

The XV-15 Tilt-Rotor wing has six major aeroelastic modes that are close in frequency. To precisely excite individual modes during flight test, dual flaperon exciters with automatic frequency-sweep controls were installed. The resulting structural data were analyzed in the frequency domain (Fourier transformed) with cross spectral and transfer function methods. Modal frequencies and damping were determined by performing curve fits to transfer function magnitude and phase data and to cross spectral magnitude data. Results are given for the XV-15 with its original metal rotor blades. Frequency and damping values are also compared with earlier predictions.

Acree, C. W., Jr.↗
NASA NTRS1988

Using frequency-domain methods to identify XV-15 aeroelastic modes

The XV-15 Tilt-Rotor wing has six major aeroelastic modes that are close in frequency. To precisely excite individual modes during flight test, dual flaperon exciters with automatic frequency-sweep controls were installed. The resulting structural data were analyzed in the frequency domain (Fourier transformed) with cross spectral and transfer function methods. Modal frequencies and damping were determined by performing curve fits to transfer function magnitude and phase data and to cross spectral magnitude data. Results are given for the XV-15 with its original metal rotor blades. Frequency and damping values are also compared with earlier predictions.

Acree, C. W., Jr.↗
NASA NTRS1982

Laser measurement of the spectral extinction coefficients of fluorescent, highly absorbing liquids

A conceptual method is developed to deduce rapidly the spectral extinction coefficient of fluorescent, highly absorbing liquids, such as crude or refined petroleum oils. The technique offers the advantage of only requiring one laser wavelength and a single experimental assembly and execution for any specific fluorescent liquid. The liquid is inserted into an extremely thin wedge-shaped cavity for stimulation by a laser from one side and flurescence measurement on the other side by a monochromator system. For each arbitrarily selected extinction wavelength, the wedge is driven slowly to increasing thicknesses until the fluorescence extinguishes. The fluorescence as a function of wedge thickness permits a determination of the extinction coefficient using an included theoretical model. When the monochromator is set to the laser emission wavelength, the extinction coefficient is determined using the usual on-wavelength signal extinction procedure.

Hoge, F. E.↗
NASA NTRS1995

Satellite estimation of spectral UVB irradiance using TOMS derived total ozone and UV reflectivity

A method for satellite remote sensing of spectral UVB radiation incident at the earth's surface for snow and/or ice free areas has been developed. Measurements of total ozone and UV reflectively from the Nimbus-7 Total Ozone Mapping Spectrometer (TOMS) instrument have been applied to this technique. Comparison of satellite estimates with ground based measurements of spectral UVB irradiance show differences which are comparable to differences between near simultaneous measurements made with two or more ground based co-located instruments.

Eck, T. F.↗
NASA NTRS1972

Serial segment method for measuring remnant

For tracking tasks where a sum of sine waves forcing function is used it is often difficult and/or expensive to obtain the pilot's remnant in the vicinity of the sine waves. For the case where each sine wave has at least four times an integer number of cycle per run length, this paper illustrates the serial segments method for measuring remnant power spectral density in a frequency band centered on each sine wave. This method can be implemented on digital, hybrid, or analog Fourier coefficient analyzers, and is particularly advantageous on the latter since properties of Fourier coefficients are exploited to yield both a remnant measure and an improved estimate of the correlated component.

Magdaleno, R. E.↗
NASA NTRS2005

On the determination of atmospheric minor gases by the method of vanishing partial derivatives with application to CO2

We present a general method for the determination of minor gases in the troposphere from high spectral resolution observations. In this method, we make use of a general property of the total differential of multi-variable functions to separate the contributions of each individual minor gas. We have applied this method to derive the mixing ratio of carbon dioxide in the mid-troposphere using data from the Atmospheric Infrared Sounder (AIRS) currently flying on the NASA Aqua Mission. We compare our results to the aircraft flask CO2 measurements obtained by H. Matsueda et al. over the western Pacific and demonstrate skill in tracking the measured 5 ppmv seasonal variation with an accuracy of 0.43 +/- 1.20 ppmv.

Atmospheric Infrared Sounder (AIRS)↗
NASA NTRS1977

Plasma effects on the spontaneous emission of synchrotron radiation from weakly relativistic electrons

A method for computing the spectral emissivity of spontaneous synchrotron radiation is discussed. The Klimontovich (1967) formalism in plasma kinetic theory is adopted in which an ensemble average of the microscopically emitted power is considered. The present method clarifies the meaning of the random phase approximation which is imposed in several existing theories of synchrotron radiation. Both the effects of dielectric polarization and two-particle correlations are included in the present discussion. The theory is applied to the case of a plasma in thermal equilibrium, for which it is shown that the effect of pair correlations on the emissivity vanishes. On the other hand, the effect of dielectric polarization is studied numerically for a wide range of parameters.

Freund, H. P.↗
NASA NTRS1987

Ocean color spectral variability studies using solar-induced chlorophyll fluorescence

It is suggested that chlorophyll-induced ocean color spectral variability can be studied using only a passive airborne spectroradiometer instrument, with solar-induced chlorophyll fluorescence used as the standard against which all correlations are performed. The intraspectral correlation (ISC) method is demonstrated with results obtained during an airborne mapping mission in the New York Bight. The curvature algorithm is applied to the solar-induced chlorophyll fluorescence at about 690 nm, and good agreement is found with results obtained using active-passive correlation spectroscopy. The ISC method has application to spectral variability and resulting chlorophyll concentration measurement in different environmental conditions and in different water types.

Hoge, Frank E.↗
NASA NTRS1990

Comparison of satellite based cloud retrieval methods for cirrus and stratocumulus

One difficulty in using satellite remote sensing data is the spatial variability of cloud properties on scales smaller than most meteorological satellite fields of view (approx. 4 to 8 km). The variation is examined of satellite derived cloud cover as a function of the satellite sensor spatial resolution for seven cloud cover retrieval methods: (1) Reflectance threshold; (2) Temperature threshold; (3) ISCCP; (4) HBTM (Hybrid Bispectral Threshold Method); (5) NCLE; (6) Spatial coherence; and (7) Functional Box Counting. The first two methods are simple single spectral thresholds which specify a satellite pixel as cloud filled if the measured reflectance is greater than the threshold, or if the measured equivalent blackbody temperature is less than the threshold. The next three methods are bispectral, using one visible wavelength window channel and one thermal infrared wavelength window. The final two algorithms rely on the spatial variability within the cloud field to determine cloud cover. Spatial coherence assumes only that the cloud field occurs in a single layer and that the clouds are optically thick in the infrared window. LANDSAT Thematic Mapper (TM) data is used to test the spatial resolution dependence of the cloud algorithms. The ISCCP bispectral threshold applied to the full resolution data is used as the reference or truth cloud cover, after which the retrieval methods are applied to the spatial resolutions. Studies of the fraction of pixels in the scene at cloud edge, and of the profile of reflectance and temperature near cloud edges indicate an uncertainty in the reference cloud fraction of 1 to 5 percent.

Parker, Lindsay↗
NASA NTRS2001

Apparatus and method using a holographic optical element for converting a spectral distribution to image points

A holographic optical element transforms a spectral distribution of light to image points. The element comprises areas, each of which acts as a separate lens to image the light incident in its area to an image point. Each area contains the recorded hologram of a point source object. The image points can be made to lie in a line in the same focal plane so as to align with a linear array detector. A version of the element has been developed that has concentric equal areas to match the circular fringe pattern of a Fabry-Perot interferometer. The element has high transmission efficiency, and when coupled with high quantum efficiency solid state detectors, provides an efficient photon-collecting detection system. The element may be used as part of the detection system in a direct detection Doppler lidar system or multiple field of view lidar system.

McGill, Matthew J.↗
NASA NTRS1989

Solving the shallow water equations on the Cray X-MP/48 and the connection machine 2

The shallow water equations in Cartesian coordinates and 2-D are solved on the Connection Machine 2 (CM-2) using both the spectral and finite difference methods. A description of these implementations is presented together with a brief discussion of the CM-2 as it relates to these specific computations. The finite difference code was written both in C* and *LISP and the spectral code was written in *LISP. The performance of the codes is compared with a FORTRAN version that was optimized for the Cray X-MP/48.

Swarztrauber, Paul N.↗