SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The addition of metals or alloys whose hydrides have a high dissociation pressure allows a considerable increase in the hydrogenation rate of magnesium. The influence of temperature and hydrogen pressure on the reaction rate were studied. Results concerning the hydriding of magnesium rich alloys such as Mg2Ca, La2Mg17 and CeMg12 are presented. The hydriding mechanism of La2Mg17 and CeMg12 alloys is given.
Additive manufacturing (AM) allows for the fabrication of complex near net shape components, leading to new design opportunities and significant savings, for example by decreasing tooling and materials cost or by accelerating prototype development. New Ni-based alloy heat exchangers with thin-walled areas exposed to hot gases will, however, suffer from corrosion degradation, and the high temperature oxidation performance of AM alloys needs to be addressed. Alloy N06002 (Ni-22Cr-18Fe-9Mo) fabricated by electron beam melting (EBM) and selective laser melting (SLM) along with EBM-fabricated N07247 and modified N07247 were cyclic oxidation tested at 950°C in air and humid air for durations ranging from 100 h to 5000 h. Increased spallation rates were observed initially for the AM N06002 alloys in comparison with wrought N06002 alloy because of the AM alloy specific microstructures. After ~2000 h, the situation was reversed with significant spallation observed for the wrought HX alloy only. Low mass gains were observed for the EBM N07247 alloys at 950°C, but thick oxide scales were observed locally due to the presence of oxidized cracks. Massive oxidation of these cracks led to fast oxidation rates at 1100°C.
At low temperatures (< 400°C), single atoms of Rh supported on rutile TiO 2 (rTiO 2 ) are responsible for the formation of CO during the reverse water gas shift (RWGS), while methane production is associated with the Rh-TiO 2 interface due to the correlation between methane formation rates and the volume-averaged Rh nanoparticle diameter. As the temperature is increased to >540°C, there is a notable increase in CO selectivity and methane production rates tend towards zero. The time to reach zero depends on the temperature but independent of the initial Rh structure (single atoms and/or nanoparticles), which is controlled by the catalyst preparation method (wetness impregnation versus colloidal nanoparticles). At 600°C and > 4 h time on stream, the catalytic behaviour becomes completely agnostic to the initial Rh structure as well as weight loading, and the catalysts are highly selective for the reverse water gas-shift reaction. Post-reaction HR-TEM image analysis confirms Rh nanoparticles crystallize/order during the reaction; at 400°C, most of the Rh particles are disordered, while at 600°C, they are more ordered (i.e., development of defined faceting). Infrared spectroscopy of CO adsorption on Rh nanoparticles confirms the appearance of defined facets after annealing in nitrogen at high temperatures. Annealing the Rh/rTiO 2 catalysts prior to the RWGS reaction demonstrates the structural transformation of Rh depends only on time and temperature and not on reactant or product fugacity. Sites responsible for stabilizing Rh single atoms are no longer competent at higher temperatures, enabling their integration into existent nanoparticles. As the reaction temperature is increased to temperatures >540°C, the dominant active site for CO production evolves from single atoms to extended Rh structures.
Here, this study explores the influence of heat treatment paths on the structural relaxation of metallic glasses (MGs) in the regime of fast dynamics. We create MG samples using various quenching rates, from 10 9 to 10 11 K/s, and expose these samples to near-T g heat treatments with assorted combinations of heating/cooling rates, from 5×10 10 to 5×10 12 K/s, and annealing durations, from 10 ps to 10 ns. Results show that the effect of the heating rate is intricately tied to the initial structure of the MG, while a decrease in the cooling rate invariably intensifies the aging process. Extending the annealing duration may induce either aging or rejuvenation, subject to the specific thermal history. To interpret these findings, we hypothesize that the memory effect, governed by the activation and annihilation of reversible and irreversible flow units, underpins the rejuvenation-aging competition in MGs. Moreover, we suggest viewing the cooling stage as an annealing phase controlled by gradient temperature and fine-tuning its rate to achieve the targeted active flow unit distributions. This study illuminates the role of fast dynamics during the glass relaxation process and offers practical strategies for tailoring heat treatments to optimize MG structures and mechanical performance.
Developing stable cathode materials represents a crucial step toward long-life sodium-ion batteries. P2-type layered oxides are important as cathodes for their reversibility, but their long-term performance in full cells remains a key challenge. Herein, we report Na 0.75 Co 0.125 Cu 0.125 Fe 0.125 Ni 0.125 Mn 0.5 O 2 with an intergrowth of ordered P2 and P3 phases, studied by neutron diffraction and Rietveld refinement. A stable electrochemical performance is achieved in Na half cells with 100% capacity retention at a rate of C/10 after 100 cycles (initial capacity of 90 mAh/g), 96% capacity retention at a rate of 1 C after 500 cycles (initial capacity of 70 mAh/g), and 85% capacity retention at a rate of 5 C after 1000 cycles (initial capacity of 55 mAh/g). Stable full cell performance is achieved with 84.2% capacity retention after 1000 cycles at a rate of 1 C. Synchrotron X-ray diffraction, spectroscopy, and imaging are applied to elucidate the relationship between chemical/structural evolution and battery performance. A reversible local and global structural evolution is observed during initial cycles. Meanwhile, the challenges with enabling prolonged cycling (beyond 1000 cycles) may be associated with Fe dissolution and formation of a copper oxide phase. This study implies that cathodes with complex chemical and structural formations may stabilize electrochemical performance and highlights the importance of decoupling the contribution of each transition metal to performance degradation.
The anionic redox reaction (ARR) has become a hot topic in battery research due to its ability to provide high energy density. Nevertheless, there are still many issues in Na-based layered oxides with the ARR, such as large voltage hysteresis, lattice oxygen loss, irreversible structural changes, and cation migration in the TM layer, resulting in structural collapse and poor electrochemical performance. Herein, a series of Na 2/3 [Fe 1/3 Mg x Mn 2/3–x ]O 2 cathodes are synthesized using a traditional solid-state reaction method. The effectiveness of Mg substitution amounts and site occupancy in regulating the reversibility of the ARR has been explored using various experimental techniques. Surprisingly, the well-designed Na/TM-site Mg substituted P2-Na 2/3 [Fe 1/3 Mg 1/12 Mn 7/12 ]O 2 exhibits an extremely high initial reversible capacity of ~253.21 mA h g –1 , equivalent to ~0.94 e – transfer, which is contributed by both cationic and anionic redox reactions as confirmed by hard X-ray absorption spectroscopy (hXAS) and soft X-ray absorption spectroscopy (sXAS) analyses. In addition, the improved cycling and high-rate performance of the P2-Na 2/3 [Fe 1/3 Mg 1/12 Mn 7/12 ]O 2 are achieved by a well-maintained crystal structure and the highly reversible anionic redox reaction of O 2– /O n– . Finally, these in-depth studies provide crucial knowledge for the development and understanding of cathode materials with a highly reversible ARR for low-cost and high-energy sodium-ion batteries.
Here, a series of one-dimensional CuFe 2 O 4 nano/sub-micron wires possessing different diameters, crystal phases, and crystal sizes have been successfully generated using a facile template-assisted co precipitation reaction at room temperature, followed by a short post-annealing process. The diameter and the crystal structure of the resulting CuFe 2 O4 (CFO) wires were judiciously tuned by varying the pore size of the template and the post-annealing temperature, respectively. Carbon nanotubes (CNTs) were incorporated to generate CFO-CNT binder-free anodes, and multiple characterization techniques were employed with the goal of delineating the relationships between electrochemical behavior and the properties of both the CFO wires (crystal phase, wire diameter, crystal size) and the electrode architecture (binder-free vs. conventionally prepared approaches). The study reveals several notable findings. First, the crystal phase (cubic or tetragonal) did not influence the electrochemical behavior in this CFO system. Second, regarding crystallite size and wire diameter, CFO wires with larger crystallite sizes exhibit improved cycling stability, while wires possessing smaller diameters exhibiting higher capacities. Finally, the electrochemical behavior is strongly influenced by the electrode architecture, with CFO-CNT binder-free electrodes demonstrating significantly higher capacities and cycling stability compared to conventionally prepared coatings. The mechanism(s) associated with the high capacities under low current density but limited electrochemical reversibility of CFO electrodes under high current density were probed via x-ray absorption spectroscopy (XAS) mapping with sub-micron spatial resolution for the first time. Results suggest that the capacity of the binder-free electrodes under high rate is limited by the irreversible formation of Cu 0 , as well as limited reduction of Fe 3+ , to Fe 2+ not Fe 0 . The results (1) shed fundamental insight into the reversibility of CuFe 2 O 4 materials cycled at high current density and (2) demonstrate that a synergistic effort to control both active material morphology and electrode architecture is an effective strategy for optimizing electrochemical behavior.
While Li-ion batteries (LIBs) are a leading energy storage technology, their energy densities are limited by the low capacity of conventional intercalation cathodes, driving interest in high energy-density Li–S batteries that make use of conversion chemistry. Achieving high capacity, reversibility, and cycle stability, and controlling volume changes in conversion batteries during the charge–discharge process, however, remains challenging. Here, in this study, we present a porous, amorphous, sulfide-based Mn x Mo 3 S 13 chalcogel, which concurrently offers high capacity and cycle stability. The solution-processable room temperature synthesized Mn x Mo 3 S 13 (x = 0.25) chalcogel exhibits a local structure that resembles the Mo 3 S 13 cluster with Mn 2+ distributed across the Mo 3 S 13 matrix, as determined by synchrotron X-ray pair distribution function (PDF) and extended X-ray absorption fine structure (EXAFS). Ab initio molecular dynamics (AIMD) simulations reveal that Mn 2+ incorporation shortens the polysulfide chain in the gel matrix compared to the Mo 3 S 13 chalcogel, while forming a coordination environment with disulfide groups, analogous to the experimental findings. A Li/Mn 0.25 Mo 3 S 13 half-cell delivers 897 mAh g –1 capacity during the first discharge and retains 571 mAh g –1 capacity after 100 cycles at a C/3 rate. Distribution of relaxation time (DRT) unveils a stable solid–electrolyte interphase (SEI) formation upon cycling that enables charge–discharge reversibility. Here, the enhanced capacity retention and cycle stability compared to those of the Li/Mo 3 S 13 cell are attributed to the reduced dissolution of active mass into the electrolyte, facilitated by the formation of shorter polysulfide chains within the Mn 0.25 Mo 3 S 13 structure and the strong affinity of Lewis-acidic Mn 2+ for polysulfide anions generated during the charge–discharge process of the Li/Mn 0.25 Mo 3 S 13 cell. Thus, this work illustrates a design principle of material for high-capacity and cycle-stable Li-metal sulfide batteries.
Developing high-capacity electrodes requires the evaluation of electrochemical behaviors with an increasing current density. Currently, the current density for evaluation of high-capacity electrodes has reached a new stage where the polarization at the lithium counter electrode has become a technical barrier for the accurate evaluation of battery electrodes, resulting in severe performance and mechanism mischaracterizations. Here, the accurate electrochemical behavior for high-capacity electrodes via a single-channel three-electrode vehicle is decoupled, by which the impact of lithium counter electrode is minimized. The testing high-capacity graphite electrode is capable of delivering an excellent rate capability with 81.7% capacity retention at 0.3 C, as well as stable cycling performance retaining 97.5% practical reversible capacity after 225 cycles, much higher than the graphite electrode tested with traditional half-cell testing vehicle but in close agreement with the results obtained from a well-matched full cell, reflecting accurate electrochemical performance evaluations of high-capacity electrodes. Moreover, detailed electrochemical mechanisms of impedance and diffusion properties for working electrodes are also successfully decoupled individually. Here, this work uncovers the mismatch between traditional evaluation configuration and increasing testing current density and provides a guideline for accurate electrochemical evaluation for ever-increasing high-capacity electrodes, which is of great significance for high-energy lithium or other alkali-metal ion batteries.
A parametric study has been conducted to identify the effects of several parameters on the separation of CsCl from molten LiCl-KCl salt via a melt crystallization process. A reverse vertical Bridgman technique was used to grow the salt crystals. The investigated parameters were: (1) the advancement rate, (2) the crucible lid configuration, (3) the amount of salt mixture, (4) the initial composition of CsCl, and (5) the temperature difference between the high and low furnace zones. From each grown crystal, samples were taken axially and analyzed using inductively coupled plasma mass spectrometry (ICP-MS). Results show that CsCl concentrations at the top of the crystals were low and increased to a maximum at the bottom of the salt. Salt (LiCl-KCl) recycle percentages for the experiments ranged from 50% to 75% and the CsCl composition in the waste salt was low. To increase the recycle percentage and the concentration of CsCl in the waste form, the possibility of using multiple crystallization stages was explored to further optimize the process. Results show that multiple crystallization stages are practical and the optimal experimental conditions should be operated at 5.0 mm/hr rate with a lid configuration and temperature difference of 200 °C for a total of five crystallization stages. Under these conditions, up to 88% of the salt can be recycled.
Silicon-based materials demonstrate significant potential as lithium-ion batteries (LIBs) anode, but their expansion and degradation present engineering design challenges for commercial application. In this study, a porous three-dimensional (3D) graphene and micron-sized silicon composite anode (Si@G foam) was synthesized using humic acid (HA) derived from coal as a graphene precursor. In-situ formation of graphene structure through reducing HA was confirmed by Raman spectra. The reduced HA (rHA) shows similar electrical conductivity compared to the commercial conductive carbon. SEM images depict a 3D skeleton of coal-derived graphene, with silicon particles distributed on the 3D graphene foam's internal surface. The Si@G composite-anode displays a good reversible capacity of ~656 mAh/g at a current density of 50 mA/g, as well as a high-rate capability of ~433 mAh/g at a current density of 800 mA/g, and outstanding cycling stability –89.8% capacity retention after 300 cycles, which is significantly higher than that of other foam structures. During lithiation and de-lithiation, the graphene foam serves as a matrix of electrical conductors and a volume expansion support for silicon. This 3D graphene network will be beneficial for developing advanced silicon-based anodes for high-performance LIBs.
Highlights: • Synthesis of Pt–RGO nanohybrids of very high electrochemically active surface area. • Electrocatalytic activity-cum-stability: ∼10 times that of commercial Pt-C catalyst. • TEM confirms narrow size distribution and excellent dispersion of Pt nanoparticles. • SAED and XRD indicate (1 1 1) orientation of Pt nanoparticles. • Methanol oxidation EIS reveal decrease in charge transfer resistance with potential - Abstract: High quality thermally exfoliated reduced graphene oxide (RGO) nanosheets decorated with platinum nanocrystals have been synthesized using a simple environmentally benign process. The electrocatalytic behaviour of the Pt–RGO nanohybrid for methanol oxidation was studied using cyclic voltammetry, chronoamperometry and electrochemical impedance spectroscopy. High resolution transmission electron microscopy shows uniform dispersion of Pt nanoparticles of ∼2–4 nm size. X-ray diffraction and selected area diffraction studies reveal (1 1 1) orientation of the platinum nanoparticles. The cyclic voltammetry and chronoamperometry results indicate higher catalytic activity and stability for Pt–RGO compared to commercial Pt-C. The electrochemical active surface area of Pt–RGO (52.16 m{sup 2}/g) is found to be 1.5 times that of commercial Pt-C. Impedance spectroscopy shows different impedance behaviour at different potential regions, indicating change in methanol oxidation reaction mechanism with potential. The reversal of impedance pattern to the second quadrant, at potentials higher than ∼0.40 V, indicates change in the rate determining reaction.
Spinel intercalation hosts are well known to to facilitate high rate capability and high voltage Li-ion batteries. A recent experimental study has shown that Mg can reversibly intercalate in spinel TiS 2 , demonstrating the viability of Li intercalation host crystal structures for Mg-ion batteries. We report on a first-principles statistical mechanics study of Mg insertion into spinel TiS 2 , accounting for occupancy on both octahedrally and tetrahedrally coordinated interstitial sites. In contrast to Li-containing spinels, we predict mixed octahedral and tetrahedral site occupancy at nondilute Mg concentrations consistent with the recent experimental study of Sun et al. The onset of mixed occupancy is correlated with an increase in the spinel volume upon Mg insertion, which is more pronounced in MgxTiS 2 than in its Li counterpart. Lastly, the results in this study suggest that the degree of mixed occupancy could be controlled through the volume of the host with addition of electrochemically inactive species.
Abstract Developing highly efficient and reversible hydrogenation-dehydrogenation catalysts shows great promise for hydrogen storage technologies with highly desirable economic and ecological benefits. Herein, we show that reaction sites consisting of single Pt atoms and neighboring oxygen vacancies (V O ) can be prepared on CeO 2 (Pt 1 /CeO 2 ) with unique catalytic properties for the reversible dehydrogenation and rehydrogenation of large molecules such as cyclohexane and methylcyclohexane. Specifically, we find that the dehydrogenation rate of cyclohexane and methylcyclohexane on such sites can reach values above 32,000 mol H2 mol Pt −1 h −1 , which is 309 times higher than that of conventional supported Pt nanoparticles. Combining of DRIFTS, AP-XPS, EXAFS, and DFT calculations, we show that the Pt 1 /CeO 2 catalyst exhibits a super-synergistic effect between the catalytic Pt atom and its support, involving redox coupling between Pt and Ce ions, enabling adsorption, activation and reaction of large molecules with sufficient versatility to drive abstraction/addition of hydrogen without requiring multiple reaction sites.
An agent-based discrete computational model biologically calibrated to Pseudomonas aeruginosa migration is used to explore the impacts of bacterial reversals and wrap mode on the efficiency of motion in different environments, both with and without chemotaxis. It is first shown that wrap mode increases the exploration of continuous multimodal chemotactic profiles such as those produced by biologically relevant fungal networks. For cells undergoing a run-reverse pattern, it is shown that the bacteria are likely to remain at the first local chemoattractant maximal production site on a hypha they find. However, with wrap mode, the bacteria can more easily escape these local sites to further explore their neighboring environment along the fungi, suggesting that wrap mode may be beneficial for migration along the fungi in liquid. In a different set of simulations of bacterial motion close to an isolated chemotactic source, wrap mode is shown to increase the ability of a bacterium to reorient toward the source while reducing the overall motion required for similar chemotactic efficiency as a run-reverse strategy, suggesting a potential metabolic benefit. In contrast, model simulations show that wrap mode can increase the rate of dispersal of P. aeruginosa in a nonchemotactic environment.
A lithium charge storage mechanism is discovered at the interface of nano-crystallites of LiTiS 2 in the solid state. The surface titanium atoms can be reduced reversibly at higher voltages. Electrochemically, this appears as a pseudocapacitive effect boosting capacity greater than theoretical at high rate with no liquid electrolyte.
Lithium iron silicate, Li 2 FeSiO 4 , is a promising cathode material for lithium ion batteries due to its high theoretical specific capacity, earth abundance, low cost, and environmental friendliness. The challenges of Li 2 FeSiO 4 as a practical cathode material are (1) the low electronic and ionic conductivity and (2) the low discharge voltage. The approach of incorporating graphene sheets into the nanostructure of Li 2 FeSiO 4 is used for dealing with the low conductivities while fluorine doping is intended to increase the discharge voltage. The fluorine-doped and graphene-incorporated iron-rich lithium iron silicate F-LFSO/G nanomaterials were successfully synthesized using a facile/efficient hydrothermal method with excellent performance, 328.43 mA h g -1 at 0.1C rate, approaching their theoretical specific capacity, 99% of 331 mA h g -1 . This clearly reveals that the reversible (de)lithiation of 2 Li + ions per F-LFSO has been realized as a result of these approaches. The (de)lithiation process has been studied using in operando high energy synchrotron X-ray absorption near edge spectroscopy and X-ray photoelectron spectroscopy aided by theoretical modeling, which reveals that F doping deeply changes the O electron configuration in F-LFSO, and consequently makes the Li + ion transfer easier, while the reversible redox of oxygen can be utilized to achieve high specific capacity.
Energy conversion technologies that are key to decarbonization efforts face significant durability challenges due to variable operation. Understanding the impact of variable operation on catalytic stability and identifying the key variables that dictate degradation is crucial for developing robust technologies. Here, we present a comprehensive investigation of the effects of variable operation on liquid alkaline water electrolysis. Our findings reveal that variable operation induces severe degradation of Ni, Fe, and Co catalytic films that is not observed during steady-state operation. By systematically interrogating the electrode discharge during simulated shutdown tests using Raman spectroscopy and mass spectrometry techniques, we uncover significant alterations caused by reverse currents in real time. These include changes in crystal structure, composition, film thickness, electronic conductivity, and dissolution rates. Lab-scale electrolyzer experiments further highlight the impact of variable operation on catalyst materials under relevant conditions. Finally, we provide guidelines for leveraging these insights to advance electrocatalysis research. This work underscores the importance of integrating realistic stressors into stability testing and offers practical guidelines for catalyst design, performance evaluation, and industrial implementation. Collectively, insights from this study will drive the development of more resilient energy conversion technologies.